Update runtime files.

1 files changed, 11 insertions, 6 deletions

diff --git a/runtime/doc/map.txt b/runtime/doc/map.txt
index c2eb76c5ff..ef3126193c 100644
--- a/runtime/doc/map.txt
+++ b/runtime/doc/map.txt
@@ -1,4 +1,4 @@
-*map.txt*       For Vim version 9.0.  Last change: 2023 Jan 09
+*map.txt*       For Vim version 9.0.  Last change: 2023 Feb 18
 
 
 		  VIM REFERENCE MANUAL    by Bram Moolenaar
@@ -845,7 +845,7 @@ option).  After that it assumes that the 'q' is to be interpreted as such.  If
 you type slowly, or your system is slow, reset the 'timeout' option.  Then you
 might want to set the 'ttimeout' option.
 
-			      				*map-precedence*
+							*map-precedence*
 Buffer-local mappings (defined using |:map-<buffer>|) take precedence over
 global mappings.  When a buffer-local mapping is the same as a global mapping,
 Vim will use the buffer-local mapping.  In addition, Vim will use a complete
@@ -923,6 +923,11 @@ in the original Vi, you would get back the text before the first undo).
 
 1.10 MAPPING ALT-KEYS					*:map-alt-keys*
 
+For a readable mapping command the <A-k> form can be used.  Note that <A-k>
+and <A-K> are different, the latter will use an upper case letter.  Actually,
+<A-K> and <A-S-K> are the same.  Instead of "A" you can use "M".  If you have
+an actual Meta modifier key, please see |:map-meta-keys|.
+
 In the GUI Vim handles the Alt key itself, thus mapping keys with ALT should
 always work.  But in a terminal Vim gets a sequence of bytes and has to figure
 out whether ALT was pressed or not.
@@ -1028,7 +1033,7 @@ enabled when it spots an escape sequence that must have been created by it.
 To see if Vim detected such an escape sequence use `:verbose map`, the first
 line will then show "Seen modifyOtherKeys: true" (possibly translated).
 
-This automatic detection depends on receiving an escape code starting with 
+This automatic detection depends on receiving an escape code starting with
 "<1b>[27;".  This is the normal way xterm sends these key codes.  However, if
 the *formatOtherKeys* resource is set another form is used that is not
 recognized, therefore you must not set formatOtherKeys.
@@ -1069,7 +1074,7 @@ translated).  The meaning of {value}:
 	Disabled	protocol was used but expected to have been disabled
 			by 't_TE'
 	Cleared		protocol expected to have beeen disabled by 't_TE',
-			previous state is unknown 
+			previous state is unknown
 
 
 1.14 MAPPING AN OPERATOR				*:map-operator*
@@ -1212,7 +1217,7 @@ non-id	  The "non-id" type ends in a non-keyword character, the other
 Examples of strings that cannot be abbreviations: "a.b", "#def", "a b", "_$r"
 
 An abbreviation is only recognized when you type a non-keyword character.
-This can also be the <Esc> that ends insert mode or the <CR> that ends a
+This can also be the <Esc> that ends Insert mode or the <CR> that ends a
 command.  The non-keyword character which ends the abbreviation is inserted
 after the expanded abbreviation.  An exception to this is the character <C-]>,
 which is used to expand an abbreviation without inserting any extra
@@ -1723,7 +1728,7 @@ by default correspond to the current line, last line and the whole buffer,
 relate to arguments, (loaded) buffers, windows or tab pages.
 
 Possible values are (second column is the short name used in listing):
-    -addr=lines		  	Range of lines (this is the default for -range)
+    -addr=lines			Range of lines (this is the default for -range)
     -addr=arguments	  arg	Range for arguments
     -addr=buffers	  buf	Range for buffers (also not loaded buffers)
     -addr=loaded_buffers  load	Range for loaded buffers