diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound')
25 files changed, 750 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/sound/ak4613.txt b/Documentation/devicetree/bindings/sound/ak4613.txt index 15a919522b42..1783f9ef0930 100644 --- a/Documentation/devicetree/bindings/sound/ak4613.txt +++ b/Documentation/devicetree/bindings/sound/ak4613.txt @@ -7,6 +7,16 @@ Required properties: - compatible : "asahi-kasei,ak4613" - reg : The chip select number on the I2C bus +Optional properties: +- asahi-kasei,in1-single-end : Boolean. Indicate input / output pins are single-ended. +- asahi-kasei,in2-single-end rather than differential. +- asahi-kasei,out1-single-end +- asahi-kasei,out2-single-end +- asahi-kasei,out3-single-end +- asahi-kasei,out4-single-end +- asahi-kasei,out5-single-end +- asahi-kasei,out6-single-end + Example: &i2c { diff --git a/Documentation/devicetree/bindings/sound/atmel-pdmic.txt b/Documentation/devicetree/bindings/sound/atmel-pdmic.txt new file mode 100644 index 000000000000..e0875f17c229 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/atmel-pdmic.txt @@ -0,0 +1,55 @@ +* Atmel PDMIC driver under ALSA SoC architecture + +Required properties: +- compatible + Should be "atmel,sama5d2-pdmic". +- reg + Should contain PDMIC registers location and length. +- interrupts + Should contain the IRQ line for the PDMIC. +- dmas + One DMA specifiers as described in atmel-dma.txt and dma.txt files. +- dma-names + Must be "rx". +- clock-names + Required elements: + - "pclk" peripheral clock + - "gclk" generated clock +- clocks + Must contain an entry for each required entry in clock-names. + Please refer to clock-bindings.txt. +- atmel,mic-min-freq + The minimal frequency that the micphone supports. +- atmel,mic-max-freq + The maximal frequency that the micphone supports. + +Optional properties: +- pinctrl-names, pinctrl-0 + Please refer to pinctrl-bindings.txt. +- atmel,model + The user-visible name of this sound card. + The default value is "PDMIC". +- atmel,mic-offset + The offset that should be added. + The range is from -32768 to 32767. + The default value is 0. + +Example: + pdmic@f8018000 { + compatible = "atmel,sama5d2-pdmic"; + reg = <0xf8018000 0x124>; + interrupts = <48 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(50))>; + dma-names = "rx"; + clocks = <&pdmic_clk>, <&pdmic_gclk>; + clock-names = "pclk", "gclk"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pdmic_default>; + atmel,model = "PDMIC @ sama5d2_xplained"; + atmel,mic-min-freq = <1000000>; + atmel,mic-max-freq = <3246000>; + atmel,mic-offset = <0x0>; + }; diff --git a/Documentation/devicetree/bindings/sound/da7218.txt b/Documentation/devicetree/bindings/sound/da7218.txt new file mode 100644 index 000000000000..5ca5a709b6aa --- /dev/null +++ b/Documentation/devicetree/bindings/sound/da7218.txt @@ -0,0 +1,104 @@ +Dialog Semiconductor DA7218 Audio Codec bindings + +DA7218 is an audio codec with HP detect feature. + +====== + +Required properties: +- compatible : Should be "dlg,da7217" or "dlg,da7218" +- reg: Specifies the I2C slave address + +- VDD-supply: VDD power supply for the device +- VDDMIC-supply: VDDMIC power supply for the device +- VDDIO-supply: VDDIO power supply for the device + (See Documentation/devicetree/bindings/regulator/regulator.txt for further + information relating to regulators) + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the IRQs from DA7218 are delivered to. +- interrupts: IRQ line info for DA7218 chip. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for + further information relating to interrupt properties) +- interrupt-names : Name associated with interrupt line. Should be "wakeup" if + interrupt is to be used to wake system, otherwise "irq" should be used. +- wakeup-source: Flag to indicate this device can wake system (suspend/resume). + +- clocks : phandle and clock specifier for codec MCLK. +- clock-names : Clock name string for 'clocks' attribute, should be "mclk". + +- dlg,micbias1-lvl-millivolt : Voltage (mV) for Mic Bias 1 + [<1200>, <1600>, <1800>, <2000>, <2200>, <2400>, <2600>, <2800>, <3000>] +- dlg,micbias2-lvl-millivolt : Voltage (mV) for Mic Bias 2 + [<1200>, <1600>, <1800>, <2000>, <2200>, <2400>, <2600>, <2800>, <3000>] +- dlg,mic1-amp-in-sel : Mic1 input source type + ["diff", "se_p", "se_n"] +- dlg,mic2-amp-in-sel : Mic2 input source type + ["diff", "se_p", "se_n"] +- dlg,dmic1-data-sel : DMIC1 channel select based on clock edge. + ["lrise_rfall", "lfall_rrise"] +- dlg,dmic1-samplephase : When to sample audio from DMIC1. + ["on_clkedge", "between_clkedge"] +- dlg,dmic1-clkrate-hz : DMic1 clock frequency (Hz). + [<1500000>, <3000000>] +- dlg,dmic2-data-sel : DMic2 channel select based on clock edge. + ["lrise_rfall", "lfall_rrise"] +- dlg,dmic2-samplephase : When to sample audio from DMic2. + ["on_clkedge", "between_clkedge"] +- dlg,dmic2-clkrate-hz : DMic2 clock frequency (Hz). + [<1500000>, <3000000>] +- dlg,hp-diff-single-supply : Boolean flag, use single supply for HP + (DA7217 only) + +====== + +Optional Child node - 'da7218_hpldet' (DA7218 only): + +Optional properties: +- dlg,jack-rate-us : Time between jack detect measurements (us) + [<5>, <10>, <20>, <40>, <80>, <160>, <320>, <640>] +- dlg,jack-debounce : Number of debounce measurements taken for jack detect + [<0>, <2>, <3>, <4>] +- dlg,jack-threshold-pct : Threshold level for jack detection (% of VDD) + [<84>, <88>, <92>, <96>] +- dlg,comp-inv : Boolean flag, invert comparator output +- dlg,hyst : Boolean flag, enable hysteresis +- dlg,discharge : Boolean flag, auto discharge of Mic Bias on jack removal + +====== + +Example: + + codec: da7218@1a { + compatible = "dlg,da7218"; + reg = <0x1a>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + wakeup-source; + + VDD-supply = <®_audio>; + VDDMIC-supply = <®_audio>; + VDDIO-supply = <®_audio>; + + clocks = <&clks 201>; + clock-names = "mclk"; + + dlg,micbias1-lvl-millivolt = <2600>; + dlg,micbias2-lvl-millivolt = <2600>; + dlg,mic1-amp-in-sel = "diff"; + dlg,mic2-amp-in-sel = "diff"; + + dlg,dmic1-data-sel = "lrise_rfall"; + dlg,dmic1-samplephase = "on_clkedge"; + dlg,dmic1-clkrate-hz = <3000000>; + dlg,dmic2-data-sel = "lrise_rfall"; + dlg,dmic2-samplephase = "on_clkedge"; + dlg,dmic2-clkrate-hz = <3000000>; + + da7218_hpldet { + dlg,jack-rate-us = <40>; + dlg,jack-debounce = <2>; + dlg,jack-threshold-pct = <84>; + dlg,hyst; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/da7219.txt b/Documentation/devicetree/bindings/sound/da7219.txt index 1b7030911a3b..cf61681826b6 100644 --- a/Documentation/devicetree/bindings/sound/da7219.txt +++ b/Documentation/devicetree/bindings/sound/da7219.txt @@ -28,13 +28,15 @@ Optional properties: - clocks : phandle and clock specifier for codec MCLK. - clock-names : Clock name string for 'clocks' attribute, should be "mclk". -- dlg,ldo-lvl : Required internal LDO voltage (mV) level for digital engine - [<1050>, <1100>, <1200>, <1400>] - dlg,micbias-lvl : Voltage (mV) for Mic Bias - [<1800>, <2000>, <2200>, <2400>, <2600>] + [<1600>, <1800>, <2000>, <2200>, <2400>, <2600>] - dlg,mic-amp-in-sel : Mic input source type ["diff", "se_p", "se_n"] +Deprecated properties: +- dlg,ldo-lvl : Required internal LDO voltage (mV) level for digital engine + (LDO unavailable in production HW so property no longer required). + ====== Child node - 'da7219_aad': diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt index b93362a570be..3e26a9478e57 100644 --- a/Documentation/devicetree/bindings/sound/fsl,asrc.txt +++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt @@ -25,6 +25,11 @@ Required properties: "mem" Peripheral access clock to access registers. "ipg" Peripheral clock to driver module. "asrck_<0-f>" Clock sources for input and output clock. + "spba" The spba clock is required when ASRC is placed as a + bus slave of the Shared Peripheral Bus and when two + or more bus masters (CPU, DMA or DSP) try to access + it. This property is optional depending on the SoC + design. - big-endian : If this property is absent, the little endian mode will be in use as default. Otherwise, the big endian diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt index d3b6b5f48010..cd3ee5d84f03 100644 --- a/Documentation/devicetree/bindings/sound/fsl,esai.txt +++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt @@ -27,6 +27,11 @@ Required properties: derive HCK, SCK and FS. "fsys" The system clock derived from ahb clock used to derive HCK, SCK and FS. + "spba" The spba clock is required when ESAI is placed as a + bus slave of the Shared Peripheral Bus and when two + or more bus masters (CPU, DMA or DSP) try to access + it. This property is optional depending on the SoC + design. - fsl,fifo-depth : The number of elements in the transmit and receive FIFOs. This number is the maximum allowed value for diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt index b5ee32ee3706..4ca39ddc0417 100644 --- a/Documentation/devicetree/bindings/sound/fsl,spdif.txt +++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt @@ -27,6 +27,11 @@ Required properties: Transceiver Clock Diagram" of SoC reference manual. It can also be referred to TxClk_Source bit of register SPDIF_STC. + "spba" The spba clock is required when SPDIF is placed as a + bus slave of the Shared Peripheral Bus and when two + or more bus masters (CPU, DMA or DSP) try to access + it. This property is optional depending on the SoC + design. - big-endian : If this property is absent, the native endian mode will be in use as default, or the big endian mode diff --git a/Documentation/devicetree/bindings/sound/img,i2s-in.txt b/Documentation/devicetree/bindings/sound/img,i2s-in.txt new file mode 100644 index 000000000000..423265cfc3d6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,i2s-in.txt @@ -0,0 +1,47 @@ +Imagination Technologies I2S Input Controller + +Required Properties: + + - compatible : Compatible list, must contain "img,i2s-in" + + - #sound-dai-cells : Must be equal to 0 + + - reg : Offset and length of the register set for the device + + - clocks : Contains an entry for each entry in clock-names + + - clock-names : Must include the following entry: + "sys" The system clock + + - dmas: Contains an entry for each entry in dma-names. + + - dma-names: Must include the following entry: + "rx" Single DMA channel used by all active I2S channels + + - img,i2s-channels : Number of I2S channels instantiated in the I2S in block + +Optional Properties: + + - interrupts : Contains the I2S in interrupts. Depending on + the configuration, there may be no interrupts, one interrupt, + or an interrupt per I2S channel. For the case where there is + one interrupt per channel, the interrupts should be listed + in ascending channel order + + - resets: Contains a phandle to the I2S in reset signal + + - reset-names: Contains the reset signal name "rst" + +Example: + +i2s_in: i2s-in@18100800 { + compatible = "img,i2s-in"; + reg = <0x18100800 0x200>; + interrupts = <GIC_SHARED 7 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdc 30 0xffffffff 0>; + dma-names = "rx"; + clocks = <&cr_periph SYS_CLK_I2S_IN>; + clock-names = "sys"; + img,i2s-channels = <6>; + #sound-dai-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/img,i2s-out.txt b/Documentation/devicetree/bindings/sound/img,i2s-out.txt new file mode 100644 index 000000000000..0159415b3338 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,i2s-out.txt @@ -0,0 +1,51 @@ +Imagination Technologies I2S Output Controller + +Required Properties: + + - compatible : Compatible list, must contain "img,i2s-out" + + - #sound-dai-cells : Must be equal to 0 + + - reg : Offset and length of the register set for the device + + - clocks : Contains an entry for each entry in clock-names + + - clock-names : Must include the following entries: + "sys" The system clock + "ref" The reference clock + + - dmas: Contains an entry for each entry in dma-names. + + - dma-names: Must include the following entry: + "tx" Single DMA channel used by all active I2S channels + + - img,i2s-channels : Number of I2S channels instantiated in the I2S out block + + - resets: Contains a phandle to the I2S out reset signal + + - reset-names: Contains the reset signal name "rst" + +Optional Properties: + + - interrupts : Contains the I2S out interrupts. Depending on + the configuration, there may be no interrupts, one interrupt, + or an interrupt per I2S channel. For the case where there is + one interrupt per channel, the interrupts should be listed + in ascending channel order + +Example: + +i2s_out: i2s-out@18100A00 { + compatible = "img,i2s-out"; + reg = <0x18100A00 0x200>; + interrupts = <GIC_SHARED 13 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdc 23 0xffffffff 0>; + dma-names = "tx"; + clocks = <&cr_periph SYS_CLK_I2S_OUT>, + <&clk_core CLK_I2S>; + clock-names = "sys", "ref"; + img,i2s-channels = <6>; + resets = <&pistachio_reset PISTACHIO_RESET_I2S_OUT>; + reset-names = "rst"; + #sound-dai-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/img,parallel-out.txt b/Documentation/devicetree/bindings/sound/img,parallel-out.txt new file mode 100644 index 000000000000..a3015d2a06e0 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,parallel-out.txt @@ -0,0 +1,44 @@ +Imagination Technologies Parallel Output Controller + +Required Properties: + + - compatible : Compatible list, must contain "img,parallel-out". + + - #sound-dai-cells : Must be equal to 0 + + - reg : Offset and length of the register set for the device. + + - dmas: Contains an entry for each entry in dma-names. + + - dma-names: Must include the following entry: + "tx" + + - clocks : Contains an entry for each entry in clock-names. + + - clock-names : Includes the following entries: + "sys" The system clock + "ref" The reference clock + + - resets: Contains a phandle to the parallel out reset signal + + - reset-names: Contains the reset signal name "rst" + +Optional Properties: + + - interrupts : Contains the parallel out interrupt, if present + +Example: + +parallel_out: parallel-out@18100C00 { + compatible = "img,parallel-out"; + reg = <0x18100C00 0x100>; + interrupts = <GIC_SHARED 19 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdc 16 0xffffffff 0>; + dma-names = "tx"; + clocks = <&cr_periph SYS_CLK_PAUD_OUT>, + <&clk_core CLK_AUDIO_DAC>; + clock-names = "sys", "ref"; + resets = <&pistachio_reset PISTACHIO_RESET_PRL_OUT>; + reset-names = "rst"; + #sound-dai-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/img,pistachio-internal-dac.txt b/Documentation/devicetree/bindings/sound/img,pistachio-internal-dac.txt new file mode 100644 index 000000000000..4cc18fc0477e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,pistachio-internal-dac.txt @@ -0,0 +1,18 @@ +Pistachio internal DAC DT bindings + +Required properties: + + - compatible: "img,pistachio-internal-dac" + + - img,cr-top : Must contain a phandle to the top level control syscon + node which contains the internal dac control registers + + - VDD-supply : Digital power supply regulator (+1.8V or +3.3V) + +Examples: + +internal_dac: internal-dac { + compatible = "img,pistachio-internal-dac"; + img,cr-top = <&cr_top>; + VDD-supply = <&supply3v3>; +}; diff --git a/Documentation/devicetree/bindings/sound/img,spdif-in.txt b/Documentation/devicetree/bindings/sound/img,spdif-in.txt new file mode 100644 index 000000000000..aab9a81f7e13 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,spdif-in.txt @@ -0,0 +1,41 @@ +Imagination Technologies SPDIF Input Controller + +Required Properties: + + - compatible : Compatible list, must contain "img,spdif-in" + + - #sound-dai-cells : Must be equal to 0 + + - reg : Offset and length of the register set for the device + + - dmas: Contains an entry for each entry in dma-names. + + - dma-names: Must include the following entry: + "rx" + + - clocks : Contains an entry for each entry in clock-names + + - clock-names : Includes the following entries: + "sys" The system clock + +Optional Properties: + + - resets: Should contain a phandle to the spdif in reset signal, if any + + - reset-names: Should contain the reset signal name "rst", if a + reset phandle is given + + - interrupts : Contains the spdif in interrupt, if present + +Example: + +spdif_in: spdif-in@18100E00 { + compatible = "img,spdif-in"; + reg = <0x18100E00 0x100>; + interrupts = <GIC_SHARED 20 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdc 15 0xffffffff 0>; + dma-names = "rx"; + clocks = <&cr_periph SYS_CLK_SPDIF_IN>; + clock-names = "sys"; + #sound-dai-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/img,spdif-out.txt b/Documentation/devicetree/bindings/sound/img,spdif-out.txt new file mode 100644 index 000000000000..470a5191e101 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/img,spdif-out.txt @@ -0,0 +1,44 @@ +Imagination Technologies SPDIF Output Controller + +Required Properties: + + - compatible : Compatible list, must contain "img,spdif-out" + + - #sound-dai-cells : Must be equal to 0 + + - reg : Offset and length of the register set for the device + + - dmas: Contains an entry for each entry in dma-names. + + - dma-names: Must include the following entry: + "tx" + + - clocks : Contains an entry for each entry in clock-names. + + - clock-names : Includes the following entries: + "sys" The system clock + "ref" The reference clock + + - resets: Contains a phandle to the spdif out reset signal + + - reset-names: Contains the reset signal name "rst" + +Optional Properties: + + - interrupts : Contains the parallel out interrupt, if present + +Example: + +spdif_out: spdif-out@18100D00 { + compatible = "img,spdif-out"; + reg = <0x18100D00 0x100>; + interrupts = <GIC_SHARED 21 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdc 14 0xffffffff 0>; + dma-names = "tx"; + clocks = <&cr_periph SYS_CLK_SPDIF_OUT>, + <&clk_core CLK_SPDIF>; + clock-names = "sys", "ref"; + resets = <&pistachio_reset PISTACHIO_RESET_SPDIF_OUT>; + reset-names = "rst"; + #sound-dai-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/inno-rk3036.txt b/Documentation/devicetree/bindings/sound/inno-rk3036.txt new file mode 100644 index 000000000000..758de8e27561 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/inno-rk3036.txt @@ -0,0 +1,20 @@ +Inno audio codec for RK3036 + +Inno audio codec is integrated inside RK3036 SoC. + +Required properties: +- compatible : Should be "rockchip,rk3036-codec". +- reg : The registers of codec. +- clock-names : Should be "acodec_pclk". +- clocks : The clock of codec. +- rockchip,grf : The phandle of grf device node. + +Example: + + acodec: acodec-ana@20030000 { + compatible = "rk3036-codec"; + reg = <0x20030000 0x4000>; + rockchip,grf = <&grf>; + clock-names = "acodec_pclk"; + clocks = <&cru ACLK_VCODEC>; + }; diff --git a/Documentation/devicetree/bindings/sound/pcm1792a.txt b/Documentation/devicetree/bindings/sound/pcm179x.txt index 970ba1ed576f..4ae70d3462d6 100644 --- a/Documentation/devicetree/bindings/sound/pcm1792a.txt +++ b/Documentation/devicetree/bindings/sound/pcm179x.txt @@ -1,4 +1,4 @@ -Texas Instruments pcm1792a DT bindings +Texas Instruments pcm179x DT bindings This driver supports the SPI bus. diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index c57cbd65736c..8ee0fa91e4a0 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -7,8 +7,11 @@ Required properties: "renesas,rcar_sound-gen3" if generation3 Examples with soctypes are: - "renesas,rcar_sound-r8a7778" (R-Car M1A) + - "renesas,rcar_sound-r8a7779" (R-Car H1) - "renesas,rcar_sound-r8a7790" (R-Car H2) - "renesas,rcar_sound-r8a7791" (R-Car M2-W) + - "renesas,rcar_sound-r8a7793" (R-Car M2-N) + - "renesas,rcar_sound-r8a7794" (R-Car E2) - "renesas,rcar_sound-r8a7795" (R-Car H3) - reg : Should contain the register physical address. required register is @@ -34,6 +37,8 @@ Required properties: see below for detail. - #sound-dai-cells : it must be 0 if your system is using single DAI it must be 1 if your system is using multi DAI + +Optional properties: - #clock-cells : it must be 0 if your system has audio_clkout it must be 1 if your system has audio_clkout0/1/2/3 - clock-frequency : for all audio_clkout0/1/2/3 @@ -244,3 +249,80 @@ rcar_sound: sound@ec500000 { }; }; }; + +Example: simple sound card + + rsnd_ak4643: sound { + compatible = "simple-audio-card"; + + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&ak4643>; + clocks = <&audio_clock>; + }; + }; + +&rcar_sound { + pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-names = "default"; + + /* Single DAI */ + #sound-dai-cells = <0>; + + status = "okay"; + + rcar_sound,dai { + dai0 { + playback = <&ssi0 &src2 &dvc0>; + capture = <&ssi1 &src3 &dvc1>; + }; + }; +}; + +&ssi1 { + shared-pin; +}; + +Example: simple sound card for TDM + + rsnd_tdm: sound { + compatible = "simple-audio-card"; + + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + dai-tdm-slot-num = <6>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&xxx>; + }; + }; + +Example: simple sound card for Multi channel + +&rcar_sound { + pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-names = "default"; + + /* Single DAI */ + #sound-dai-cells = <0>; + + status = "okay"; + + rcar_sound,dai { + dai0 { + playback = <&ssi0 &ssi1 &ssi2 &src0 &dvc0>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt index 962748a8d919..2b2caa281ce3 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt @@ -4,8 +4,8 @@ Renesas Sampling Rate Convert Sound Card specifies audio DAI connections of SoC Required properties: -- compatible : "renesas,rsrc-card,<board>" - Examples with soctypes are: +- compatible : "renesas,rsrc-card{,<board>}" + Examples with boards are: - "renesas,rsrc-card" - "renesas,rsrc-card,lager" - "renesas,rsrc-card,koelsch" diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt index 2267d249ca0e..b7f3a9325ebd 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -19,6 +19,7 @@ Required properties: - clock-names: should contain followings: - "i2s_hclk": clock for I2S BUS - "i2s_clk" : clock for I2S controller +- rockchip,playback-channels: max playback channels, if not set, 8 channels default. - rockchip,capture-channels: max capture channels, if not set, 2 channels default. Example for rk3288 I2S controller: @@ -31,5 +32,6 @@ i2s@ff890000 { dma-names = "tx", "rx"; clock-names = "i2s_hclk", "i2s_clk"; clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>; + rockchip,playback-channels = <8>; rockchip,capture-channels = <2>; }; diff --git a/Documentation/devicetree/bindings/sound/rt5616.txt b/Documentation/devicetree/bindings/sound/rt5616.txt new file mode 100644 index 000000000000..efc48c65198d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5616.txt @@ -0,0 +1,26 @@ +RT5616 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5616". + +- reg : The I2C address of the device. + +Pins on the device (for linking into audio routes) for RT5616: + + * IN1P + * IN2P + * IN2N + * LOUTL + * LOUTR + * HPOL + * HPOR + +Example: + +codec: rt5616@1b { + compatible = "realtek,rt5616"; + reg = <0x1b>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5651.txt b/Documentation/devicetree/bindings/sound/rt5651.txt new file mode 100644 index 000000000000..3875233095f5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5651.txt @@ -0,0 +1,41 @@ +RT5651 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5651". + +- reg : The I2C address of the device. + +Optional properties: + +- realtek,in2-differential + Boolean. Indicate MIC2 input are differential, rather than single-ended. + +- realtek,dmic-en + Boolean. true if dmic is used. + +Pins on the device (for linking into audio routes) for RT5651: + + * DMIC L1 + * DMIC R1 + * IN1P + * IN2P + * IN2N + * IN3P + * HPOL + * HPOR + * LOUTL + * LOUTR + * PDML + * PDMR + +Example: + +codec: rt5651@1a { + compatible = "realtek,rt5651"; + reg = <0x1a>; + realtek,dmic-en = "true"; + realtek,in2-diff = "false"; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5659.txt b/Documentation/devicetree/bindings/sound/rt5659.txt new file mode 100644 index 000000000000..5f79e7fde032 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5659.txt @@ -0,0 +1,75 @@ +RT5659/RT5658 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : One of "realtek,rt5659" or "realtek,rt5658". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +- realtek,in1-differential +- realtek,in3-differential +- realtek,in4-differential + Boolean. Indicate MIC1/3/4 input are differential, rather than single-ended. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using IN2N pin as dmic1 data pin + 2: using GPIO5 pin as dmic1 data pin + 3: using GPIO9 pin as dmic1 data pin + 4: using GPIO11 pin as dmic1 data pin + +- realtek,dmic2-data-pin + 0: dmic2 is not used + 1: using IN2P pin as dmic2 data pin |