diff options
106 files changed, 2343 insertions, 653 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt b/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt new file mode 100644 index 000000000000..80fcb7d70e13 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt @@ -0,0 +1,37 @@ +TI/National Semiconductor LP3943 GPIO controller + +Required properties: + - compatible: "ti,lp3943-gpio" + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. See gpio.txt in this directory for a + description of the cells format. + +Example: +Simple LED controls with LP3943 GPIO controller + +&i2c4 { + lp3943@60 { + compatible = "ti,lp3943"; + reg = <0x60>; + + gpioex: gpio { + compatible = "ti,lp3943-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; +}; + +leds { + compatible = "gpio-leds"; + indicator1 { + label = "indi1"; + gpios = <&gpioex 9 GPIO_ACTIVE_LOW>; + }; + + indicator2 { + label = "indi2"; + gpios = <&gpioex 10 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/cros-ec.txt b/Documentation/devicetree/bindings/mfd/cros-ec.txt index 5f229c5f6da9..8009c3d87f33 100644 --- a/Documentation/devicetree/bindings/mfd/cros-ec.txt +++ b/Documentation/devicetree/bindings/mfd/cros-ec.txt @@ -17,6 +17,15 @@ Required properties (SPI): - compatible: "google,cros-ec-spi" - reg: SPI chip select +Optional properties (SPI): +- google,cros-ec-spi-msg-delay: Some implementations of the EC require some + additional processing time in order to accept new transactions. If the delay + between transactions is not long enough the EC may not be able to respond + properly to subsequent transactions and cause them to hang. This property + specifies the delay, in usecs, introduced between transactions to account + for the time required by the EC to get back into a state in which new data + can be accepted. + Required properties (LPC): - compatible: "google,cros-ec-lpc" - reg: List of (IO address, size) pairs defining the interface uses diff --git a/Documentation/devicetree/bindings/mfd/lp3943.txt b/Documentation/devicetree/bindings/mfd/lp3943.txt new file mode 100644 index 000000000000..e8591d6b11b4 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/lp3943.txt @@ -0,0 +1,33 @@ +TI/National Semiconductor LP3943 MFD driver + +Required properties: + - compatible: "ti,lp3943" + - reg: I2C slave address. From 0x60 to 0x67. + +LP3943 consists of two sub-devices, lp3943-gpio and lp3943-pwm. + +For the LP3943 GPIO properties please refer to: +Documentation/devicetree/bindings/gpio/gpio-lp3943.txt + +For the LP3943 PWM properties please refer to: +Documentation/devicetree/bindings/pwm/pwm-lp3943.txt + +Example: + +lp3943@60 { + compatible = "ti,lp3943"; + reg = <0x60>; + + gpioex: gpio { + compatible = "ti,lp3943-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + pwm3943: pwm { + compatible = "ti,lp3943-pwm"; + #pwm-cells = <2>; + ti,pwm0 = <8 9 10>; + ti,pwm1 = <15>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index 78a840d7510d..15ee89c3cc7b 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -60,7 +60,7 @@ as per the datasheet of s2mps11. - LDOn - valid values for n are 1 to 38 - - Example: LDO0, LD01, LDO28 + - Example: LDO1, LD02, LDO28 - BUCKn - valid values for n are 1 to 10. - Example: BUCK1, BUCK2, BUCK9 diff --git a/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt new file mode 100644 index 000000000000..7bd9d3b12ce1 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt @@ -0,0 +1,58 @@ +TI/National Semiconductor LP3943 PWM controller + +Required properties: + - compatible: "ti,lp3943-pwm" + - #pwm-cells: Should be 2. See pwm.txt in this directory for a + description of the cells format. + Note that this hardware limits the period length to the + range 6250~1600000. + - ti,pwm0 or ti,pwm1: Output pin number(s) for PWM channel 0 or 1. + 0 = output 0 + 1 = output 1 + . + . + 15 = output 15 + +Example: +PWM 0 is for RGB LED brightness control +PWM 1 is for brightness control of LP8557 backlight device + +&i2c3 { + lp3943@60 { + compatible = "ti,lp3943"; + reg = <0x60>; + + /* + * PWM 0 : output 8, 9 and 10 + * PWM 1 : output 15 + */ + pwm3943: pwm { + compatible = "ti,lp3943-pwm"; + #pwm-cells = <2>; + ti,pwm0 = <8 9 10>; + ti,pwm1 = <15>; + }; + }; + +}; + +/* LEDs control with PWM 0 of LP3943 */ +pwmleds { + compatible = "pwm-leds"; + rgb { + label = "indi::rgb"; + pwms = <&pwm3943 0 10000>; + max-brightness = <255>; + }; +}; + +&i2c4 { + /* Backlight control with PWM 1 of LP3943 */ + backlight@2c { + compatible = "ti,lp8557"; + reg = <0x2c>; + + pwms = <&pwm3943 1 10000>; + pwm-names = "lp8557"; + }; +}; diff --git a/arch/arm/boot/dts/tegra20-colibri-512.dtsi b/arch/arm/boot/dts/tegra20-colibri-512.dtsi index d5c9bca01232..cbe89ff10686 100644 --- a/arch/arm/boot/dts/tegra20-colibri-512.dtsi +++ b/arch/arm/boot/dts/tegra20-colibri-512.dtsi @@ -268,8 +268,8 @@ reg = <3>; regulator-compatible = "sm2"; regulator-name = "vdd_sm2,vin_ldo*"; - regulator-min-microvolt = <3700000>; - regulator-max-microvolt = <3700000>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; regulator-always-on; }; diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 25ce03eff6ab..50cc557abe41 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -406,6 +406,14 @@ config GPIO_ARIZONA help Support for GPIOs on Wolfson Arizona class devices. +config GPIO_LP3943 + tristate "TI/National Semiconductor LP3943 GPIO expander" + depends on MFD_LP3943 + help + GPIO driver for LP3943 MFD. + LP3943 can be used as a GPIO expander which provides up to 16 GPIOs. + Open drain outputs are required for this usage. + config GPIO_MAX7300 tristate "Maxim MAX7300 GPIO expander" depends on I2C diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index c44fffac9519..0248471402e4 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -35,6 +35,7 @@ obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o obj-$(CONFIG_GPIO_KEMPLD) += gpio-kempld.o obj-$(CONFIG_ARCH_KS8695) += gpio-ks8695.o obj-$(CONFIG_GPIO_INTEL_MID) += gpio-intel-mid.o +obj-$(CONFIG_GPIO_LP3943) += gpio-lp3943.o obj-$(CONFIG_ARCH_LPC32XX) += gpio-lpc32xx.o obj-$(CONFIG_GPIO_LYNXPOINT) += gpio-lynxpoint.o obj-$(CONFIG_GPIO_MAX730X) += gpio-max730x.o diff --git a/drivers/gpio/gpio-lp3943.c b/drivers/gpio/gpio-lp3943.c new file mode 100644 index 000000000000..a0341c92bcb4 --- /dev/null +++ b/drivers/gpio/gpio-lp3943.c @@ -0,0 +1,242 @@ +/* + * TI/National Semiconductor LP3943 GPIO driver + * + * Copyright 2013 Texas Instruments + * + * Author: Milo Kim <milo.kim@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2. + */ + +#include <linux/bitops.h> +#include <linux/err.h> +#include <linux/gpio.h> +#include <linux/i2c.h> +#include <linux/mfd/lp3943.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> + +enum lp3943_gpios { + LP3943_GPIO1, + LP3943_GPIO2, + LP3943_GPIO3, + LP3943_GPIO4, + LP3943_GPIO5, + LP3943_GPIO6, + LP3943_GPIO7, + LP3943_GPIO8, + LP3943_GPIO9, + LP3943_GPIO10, + LP3943_GPIO11, + LP3943_GPIO12, + LP3943_GPIO13, + LP3943_GPIO14, + LP3943_GPIO15, + LP3943_GPIO16, + LP3943_MAX_GPIO, +}; + +struct lp3943_gpio { + struct gpio_chip chip; + struct lp3943 *lp3943; + u16 input_mask; /* 1 = GPIO is input direction, 0 = output */ +}; + +static inline struct lp3943_gpio *to_lp3943_gpio(struct gpio_chip *_chip) +{ + return container_of(_chip, struct lp3943_gpio, chip); +} + +static int lp3943_gpio_request(struct gpio_chip *chip, unsigned offset) +{ + struct lp3943_gpio *lp3943_gpio = to_lp3943_gpio(chip); + struct lp3943 *lp3943 = lp3943_gpio->lp3943; + + /* Return an error if the pin is already assigned */ + if (test_and_set_bit(offset, &lp3943->pin_used)) + return -EBUSY; + + return 0; +} + +static void lp3943_gpio_free(struct gpio_chip *chip, unsigned offset) +{ + struct lp3943_gpio *lp3943_gpio = to_lp3943_gpio(chip); + struct lp3943 *lp3943 = lp3943_gpio->lp3943; + + clear_bit(offset, &lp3943->pin_used); +} + +static int lp3943_gpio_set_mode(struct lp3943_gpio *lp3943_gpio, u8 offset, + u8 val) +{ + struct lp3943 *lp3943 = lp3943_gpio->lp3943; + const struct lp3943_reg_cfg *mux = lp3943->mux_cfg; + + return lp3943_update_bits(lp3943, mux[offset].reg, mux[offset].mask, + val << mux[offset].shift); +} + +static int lp3943_gpio_direction_input(struct gpio_chip *chip, unsigned offset) +{ + struct lp3943_gpio *lp3943_gpio = to_lp3943_gpio(chip); + + lp3943_gpio->input_mask |= BIT(offset); + + return lp3943_gpio_set_mode(lp3943_gpio, offset, LP3943_GPIO_IN); +} + +static int lp3943_get_gpio_in_status(struct lp3943_gpio *lp3943_gpio, + struct gpio_chip *chip, unsigned offset) +{ + u8 ad |