Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (40 commits)
  [netdrvr] atl1: fix build
  pasemi_mac: Use local-mac-address instead of mac-address if available
  pasemi_mac: PHY support
  pasemi_mac: Add msglevel support and "debug" module param
  pasemi_mac: Logic cleanup / rx performance improvements
  pasemi_mac: Minor cleanup / define fixes
  pasemi_mac: Add SKB reuse / copy-break
  pasemi_mac: Timer and interrupt fixes
  pasemi_mac: Abstract and fix up interrupt restart routines
  pasemi_mac: Move the IRQ mapping from the PCI layer to the driver
  tc35815: Remove unnecessary skb->dev assignment
  drivers/net/dm9000: Convert to generic boolean
  AT91RM9200 Ethernet: Fix multicast addressing
  AT91RM9200 Ethernet: Support additional PHYs
  PCMCIA-NETDEV : xirc2ps_cs: bugfix of multicast code
  sky2: re-enable 88E8056 for most motherboards
  MIPS: Drop unnecessary CONFIG_ISA from RBTX49XX
  ne: MIPS: Use platform_driver for ne on RBTX49XX
  ne: Add NEEDS_PORTLIST to control ISA auto-probe
  ne: Misc fixes for platform driver.
  ...

Fix conflict in drivers/net/pasemi_mac.c (get_property() got renamed to
of_get_property()) manually.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

30 files changed, 1188 insertions, 510 deletions

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 279ec625cec4..b86ccd2ecd5b 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1104,7 +1104,7 @@ config ETH16I
 
 config NE2000
 	tristate "NE2000/NE1000 support"
-	depends on NET_ISA || (Q40 && m) || M32R
+	depends on NET_ISA || (Q40 && m) || M32R || TOSHIBA_RBTX4927 || TOSHIBA_RBTX4938
 	select CRC32
 	---help---
 	  If you have a network (Ethernet) card of this type, say Y and read
@@ -2488,6 +2488,7 @@ config NETXEN_NIC
 config PASEMI_MAC
 	tristate "PA Semi 1/10Gbit MAC"
 	depends on PPC64 && PCI
+	select PHYLIB
 	help
 	  This driver supports the on-chip 1/10Gbit Ethernet controller on
 	  PA Semi's PWRficient line of chips.
diff --git a/drivers/net/arm/at91_ether.c b/drivers/net/arm/at91_ether.c
index 152fa7a042b8..ef2cc80256a3 100644
--- a/drivers/net/arm/at91_ether.c
+++ b/drivers/net/arm/at91_ether.c
@@ -225,6 +225,16 @@ static irqreturn_t at91ether_phy_interrupt(int irq, void *dev_id)
 		if (!(phy & ((1 << 2) | 1)))
 			goto done;
 	}
+	else if (lp->phy_type == MII_T78Q21x3_ID) {			/* ack interrupt in Teridian PHY */
+		read_phy(lp->phy_address, MII_T78Q21INT_REG, &phy);
+		if (!(phy & ((1 << 2) | 1)))
+			goto done;
+	}
+	else if (lp->phy_type == MII_DP83848_ID) {
+		read_phy(lp->phy_address, MII_DPPHYSTS_REG, &phy);	/* ack interrupt in DP83848 PHY */
+		if (!(phy & (1 << 7)))
+			goto done;
+	}
 
 	update_linkspeed(dev, 0);
 
@@ -280,6 +290,19 @@ static void enable_phyirq(struct net_device *dev)
 		dsintr = (1 << 10) | ( 1 << 8);
 		write_phy(lp->phy_address, MII_TPISTATUS, dsintr);
 	}
+	else if (lp->phy_type == MII_T78Q21x3_ID) {	/* for Teridian PHY */
+		read_phy(lp->phy_address, MII_T78Q21INT_REG, &dsintr);
+		dsintr = dsintr | 0x500;		/* set bits 8, 10 */
+		write_phy(lp->phy_address, MII_T78Q21INT_REG, dsintr);
+	}
+	else if (lp->phy_type == MII_DP83848_ID) {	/* National Semiconductor DP83848 PHY */
+		read_phy(lp->phy_address, MII_DPMISR_REG, &dsintr);
+		dsintr = dsintr | 0x3c;			/* set bits 2..5 */
+		write_phy(lp->phy_address, MII_DPMISR_REG, dsintr);
+		read_phy(lp->phy_address, MII_DPMICR_REG, &dsintr);
+		dsintr = dsintr | 0x3;			/* set bits 0,1 */
+		write_phy(lp->phy_address, MII_DPMICR_REG, dsintr);
+	}
 
 	disable_mdi();
 	spin_unlock_irq(&lp->lock);
@@ -323,6 +346,19 @@ static void disable_phyirq(struct net_device *dev)
 		dsintr = ~((1 << 10) | (1 << 8));
 		write_phy(lp->phy_address, MII_TPISTATUS, dsintr);
 	}
+	else if (lp->phy_type == MII_T78Q21x3_ID) {	/* for Teridian PHY */
+		read_phy(lp->phy_address, MII_T78Q21INT_REG, &dsintr);
+		dsintr = dsintr & ~0x500;			/* clear bits 8, 10 */
+		write_phy(lp->phy_address, MII_T78Q21INT_REG, dsintr);
+	}
+	else if (lp->phy_type == MII_DP83848_ID) {	/* National Semiconductor DP83848 PHY */
+		read_phy(lp->phy_address, MII_DPMICR_REG, &dsintr);
+		dsintr = dsintr & ~0x3;				/* clear bits 0, 1 */
+		write_phy(lp->phy_address, MII_DPMICR_REG, dsintr);
+		read_phy(lp->phy_address, MII_DPMISR_REG, &dsintr);
+		dsintr = dsintr & ~0x3c;			/* clear bits 2..5 */
+		write_phy(lp->phy_address, MII_DPMISR_REG, dsintr);
+	}
 
 	disable_mdi();
 	spin_unlock_irq(&lp->lock);
@@ -535,8 +571,8 @@ static void at91ether_sethashtable(struct net_device *dev)
 		mc_filter[bitnr >> 5] |= 1 << (bitnr & 31);
 	}
 
-	at91_emac_write(AT91_EMAC_HSH, mc_filter[0]);
-	at91_emac_write(AT91_EMAC_HSL, mc_filter[1]);
+	at91_emac_write(AT91_EMAC_HSL, mc_filter[0]);
+	at91_emac_write(AT91_EMAC_HSH, mc_filter[1]);
 }
 
 /*
@@ -1062,10 +1098,16 @@ static int __init at91ether_setup(unsigned long phy_type, unsigned short phy_add
 		printk(KERN_INFO "%s: Broadcom BCM5221 PHY\n", dev->name);
 	else if (phy_type == MII_DP83847_ID)
 		printk(KERN_INFO "%s: National Semiconductor DP83847 PHY\n", dev->name);
+	else if (phy_type == MII_DP83848_ID)
+		printk(KERN_INFO "%s: National Semiconductor DP83848 PHY\n", dev->name);
 	else if (phy_type == MII_AC101L_ID)
 		printk(KERN_INFO "%s: Altima AC101L PHY\n", dev->name);
 	else if (phy_type == MII_KS8721_ID)
 		printk(KERN_INFO "%s: Micrel KS8721 PHY\n", dev->name);
+	else if (phy_type == MII_T78Q21x3_ID)
+		printk(KERN_INFO "%s: Teridian 78Q21x3 PHY\n", dev->name);
+	else if (phy_type == MII_LAN83C185_ID)
+		printk(KERN_INFO "%s: SMSC LAN83C185 PHY\n", dev->name);
 
 	return 0;
 }
@@ -1103,8 +1145,11 @@ static int __init at91ether_probe(struct platform_device *pdev)
 			case MII_RTL8201_ID:		/* Realtek RTL8201: PHY_ID1 = 0, PHY_ID2 = 0x8201 */
 			case MII_BCM5221_ID:		/* Broadcom BCM5221: PHY_ID1 = 0x40, PHY_ID2 = 0x61e0 */
 			case MII_DP83847_ID:		/* National Semiconductor DP83847:  */
+			case MII_DP83848_ID:		/* National Semiconductor DP83848:  */
 			case MII_AC101L_ID:		/* Altima AC101L: PHY_ID1 = 0x22, PHY_ID2 = 0x5520 */
 			case MII_KS8721_ID:		/* Micrel KS8721: PHY_ID1 = 0x22, PHY_ID2 = 0x1610 */
+			case MII_T78Q21x3_ID:		/* Teridian 78Q21x3: PHY_ID1 = 0x0E, PHY_ID2 = 7237 */
+			case MII_LAN83C185_ID:		/* SMSC LAN83C185: PHY_ID1 = 0x0007, PHY_ID2 = 0xC0A1 */
 				detected = at91ether_setup(phy_id, phy_address, pdev, ether_clk);
 				break;
 		}
diff --git a/drivers/net/arm/at91_ether.h b/drivers/net/arm/at91_ether.h
index b6b665de2ea0..a38fd2d053a6 100644
--- a/drivers/net/arm/at91_ether.h
+++ b/drivers/net/arm/at91_ether.h
@@ -17,39 +17,46 @@
 
 
 /* Davicom 9161 PHY */
-#define MII_DM9161_ID	0x0181b880
-#define MII_DM9161A_ID	0x0181b8a0
-
-/* Davicom specific registers */
-#define MII_DSCR_REG	16
-#define MII_DSCSR_REG	17
-#define MII_DSINTR_REG	21
+#define MII_DM9161_ID		0x0181b880
+#define MII_DM9161A_ID		0x0181b8a0
+#define MII_DSCR_REG		16
+#define MII_DSCSR_REG		17
+#define MII_DSINTR_REG		21
 
 /* Intel LXT971A PHY */
-#define MII_LXT971A_ID	0x001378E0
-
-/* Intel specific registers */
-#define MII_ISINTE_REG	18
-#define MII_ISINTS_REG	19
-#define MII_LEDCTRL_REG	20
+#define MII_LXT971A_ID		0x001378E0
+#define MII_ISINTE_REG		18
+#define MII_ISINTS_REG		19
+#define MII_LEDCTRL_REG		20
 
 /* Realtek RTL8201 PHY */
-#define MII_RTL8201_ID	0x00008200
+#define MII_RTL8201_ID		0x00008200
 
 /* Broadcom BCM5221 PHY */
-#define MII_BCM5221_ID	0x004061e0
-
-/* Broadcom specific registers */
-#define MII_BCMINTR_REG	26
+#define MII_BCM5221_ID		0x004061e0
+#define MII_BCMINTR_REG		26
 
 /* National Semiconductor DP83847 */
-#define MII_DP83847_ID	0x20005c30
+#define MII_DP83847_ID		0x20005c30
+
+/* National Semiconductor DP83848 */
+#define MII_DP83848_ID		0x20005c90
+#define MII_DPPHYSTS_REG	16
+#define MII_DPMICR_REG		17
+#define MII_DPMISR_REG		18
 
 /* Altima AC101L PHY */
-#define MII_AC101L_ID	0x00225520
+#define MII_AC101L_ID		0x00225520
 
 /* Micrel KS8721 PHY */
-#define MII_KS8721_ID	0x00221610
+#define MII_KS8721_ID		0x00221610
+
+/* Teridian 78Q2123/78Q2133 */
+#define MII_T78Q21x3_ID		0x000e7230
+#define MII_T78Q21INT_REG	17
+
+/* SMSC LAN83C185 */
+#define MII_LAN83C185_ID	0x0007C0A0
 
 /* ........................................................................ */
 
diff --git a/drivers/net/atl1/atl1_ethtool.c b/drivers/net/atl1/atl1_ethtool.c
index c11c27798e5c..1f616c5c1473 100644
--- a/drivers/net/atl1/atl1_ethtool.c
+++ b/drivers/net/atl1/atl1_ethtool.c
@@ -156,8 +156,7 @@ static int atl1_set_settings(struct net_device *netdev,
 	u16 old_media_type = hw->media_type;
 
 	if (netif_running(adapter->netdev)) {
-		printk(KERN_DEBUG "%s: ethtool shutting down adapter\n",
-			atl1_driver_name);
+		dev_dbg(&adapter->pdev->dev, "ethtool shutting down adapter\n");
 		atl1_down(adapter);
 	}
 
@@ -166,9 +165,8 @@ static int atl1_set_settings(struct net_device *netdev,
 	else {
 		if (ecmd->speed == SPEED_1000) {
 			if (ecmd->duplex != DUPLEX_FULL) {
-				printk(KERN_WARNING
-				       "%s: can't force to 1000M half duplex\n",
-					atl1_driver_name);
+				dev_warn(&adapter->pdev->dev,
+					"can't force to 1000M half duplex\n");
 				ret_val = -EINVAL;
 				goto exit_sset;
 			}
@@ -206,9 +204,8 @@ static int atl1_set_settings(struct net_device *netdev,
 	}
 	if (atl1_phy_setup_autoneg_adv(hw)) {
 		ret_val = -EINVAL;
-		printk(KERN_WARNING
-			"%s: invalid ethtool speed/duplex setting\n",
-			atl1_driver_name);
+		dev_warn(&adapter->pdev->dev,
+			"invalid ethtool speed/duplex setting\n");
 		goto exit_sset;
 	}
 	if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
@@ -239,12 +236,10 @@ exit_sset:
 		hw->media_type = old_media_type;
 
 	if (netif_running(adapter->netdev)) {
-		printk(KERN_DEBUG "%s: ethtool starting adapter\n",
-			atl1_driver_name);
+		dev_dbg(&adapter->pdev->dev, "ethtool starting adapter\n");
 		atl1_up(adapter);
 	} else if (!ret_val) {
-		printk(KERN_DEBUG "%s: ethtool resetting adapter\n",
-			atl1_driver_name);
+		dev_dbg(&adapter->pdev->dev, "ethtool resetting adapter\n");
 		atl1_reset(adapter);
 	}
 	return ret_val;
diff --git a/drivers/net/atl1/atl1_hw.c b/drivers/net/atl1/atl1_hw.c
index 69482e0d849b..ef886bdeac13 100644
--- a/drivers/net/atl1/atl1_hw.c
+++ b/drivers/net/atl1/atl1_hw.c
@@ -2,20 +2,20 @@
  * Copyright(c) 2005 - 2006 Attansic Corporation. All rights reserved.
  * Copyright(c) 2006 Chris Snook <csnook@redhat.com>
  * Copyright(c) 2006 Jay Cliburn <jcliburn@gmail.com>
- * 
+ *
  * Derived from Intel e1000 driver
  * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
- * 
+ *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the Free
  * Software Foundation; either version 2 of the License, or (at your option)
  * any later version.
- * 
+ *
  * This program is distributed in the hope that it will be useful, but WITHOUT
  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  * more details.
- * 
+ *
  * You should have received a copy of the GNU General Public License along with
  * this program; if not, write to the Free Software Foundation, Inc., 59
  * Temple Place - Suite 330, Boston, MA  02111-1307, USA.
@@ -38,12 +38,13 @@
  */
 s32 atl1_reset_hw(struct atl1_hw *hw)
 {
+	struct pci_dev *pdev = hw->back->pdev;
 	u32 icr;
 	int i;
 
-	/* 
+	/*
 	 * Clear Interrupt mask to stop board from generating
-	 * interrupts & Clear any pending interrupt events 
+	 * interrupts & Clear any pending interrupt events
 	 */
 	/*
 	 * iowrite32(0, hw->hw_addr + REG_IMR);
@@ -74,7 +75,7 @@ s32 atl1_reset_hw(struct atl1_hw *hw)
 	}
 
 	if (icr) {
-		printk (KERN_DEBUG "icr = %x\n", icr); 
+		dev_dbg(&pdev->dev, "ICR = 0x%x\n", icr);
 		return icr;
 	}
 
@@ -136,8 +137,8 @@ s32 atl1_read_phy_reg(struct atl1_hw *hw, u16 reg_addr, u16 *phy_data)
 	int i;
 
 	val = ((u32) (reg_addr & MDIO_REG_ADDR_MASK)) << MDIO_REG_ADDR_SHIFT |
-	    	MDIO_START | MDIO_SUP_PREAMBLE | MDIO_RW | MDIO_CLK_25_4 <<
- 		MDIO_CLK_SEL_SHIFT;
+		MDIO_START | MDIO_SUP_PREAMBLE | MDIO_RW | MDIO_CLK_25_4 <<
+		MDIO_CLK_SEL_SHIFT;
 	iowrite32(val, hw->hw_addr + REG_MDIO_CTRL);
 	ioread32(hw->hw_addr + REG_MDIO_CTRL);
 
@@ -204,7 +205,7 @@ static bool atl1_spi_read(struct atl1_hw *hw, u32 addr, u32 *buf)
 
 /*
  * get_permanent_address
- * return 0 if get valid mac address, 
+ * return 0 if get valid mac address,
  */
 static int atl1_get_permanent_address(struct atl1_hw *hw)
 {
@@ -301,7 +302,7 @@ static int atl1_get_permanent_address(struct atl1_hw *hw)
 }
 
 /*
- * Reads the adapter's MAC address from the EEPROM 
+ * Reads the adapter's MAC address from the EEPROM
  * hw - Struct containing variables accessed by shared code
  */
 s32 atl1_read_mac_addr(struct atl1_hw *hw)
@@ -437,6 +438,7 @@ s32 atl1_phy_enter_power_saving(struct atl1_hw *hw)
  */
 static s32 atl1_phy_reset(struct atl1_hw *hw)
 {
+	struct pci_dev *pdev = hw->back->pdev;
 	s32 ret_val;
 	u16 phy_data;
 
@@ -468,8 +470,7 @@ static s32 atl1_phy_reset(struct atl1_hw *hw)
 		u32 val;
 		int i;
 		/* pcie serdes link may be down! */
-		printk(KERN_DEBUG "%s: autoneg caused pcie phy link down\n", 
-			atl1_driver_name);
+		dev_dbg(&pdev->dev, "pcie phy link down\n");
 
 		for (i = 0; i < 25; i++) {
 			msleep(1);
@@ -479,9 +480,7 @@ static s32 atl1_phy_reset(struct atl1_hw *hw)
 		}
 
 		if ((val & (MDIO_START | MDIO_BUSY)) != 0) {
-			printk(KERN_WARNING 
-				"%s: pcie link down at least for 25ms\n", 
-				atl1_driver_name);
+			dev_warn(&pdev->dev, "pcie link down at least 25ms\n");
 			return ret_val;
 		}
 	}
@@ -571,6 +570,7 @@ s32 atl1_phy_setup_autoneg_adv(struct atl1_hw *hw)
  */
 static s32 atl1_setup_link(struct atl1_hw *hw)
 {
+	struct pci_dev *pdev = hw->back->pdev;
 	s32 ret_val;
 
 	/*
@@ -581,15 +581,13 @@ static s32 atl1_setup_link(struct atl1_hw *hw)
 	 */
 	ret_val = atl1_phy_setup_autoneg_adv(hw);
 	if (ret_val) {
-		printk(KERN_DEBUG "%s: error setting up autonegotiation\n", 
-			atl1_driver_name);
+		dev_dbg(&pdev->dev, "error setting up autonegotiation\n");
 		return ret_val;
 	}
 	/* SW.Reset , En-Auto-Neg if needed */
 	ret_val = atl1_phy_reset(hw);
 	if (ret_val) {
-		printk(KERN_DEBUG "%s: error resetting the phy\n", 
-			atl1_driver_name);
+		dev_dbg(&pdev->dev, "error resetting phy\n");
 		return ret_val;
 	}
 	hw->phy_configured = true;
@@ -631,7 +629,7 @@ static void atl1_init_flash_opcode(struct atl1_hw *hw)
  * Performs basic configuration of the adapter.
  * hw - Struct containing variables accessed by shared code
  * Assumes that the controller has previously been reset and is in a
- * post-reset uninitialized state. Initializes multicast table, 
+ * post-reset uninitialized state. Initializes multicast table,
  * and  Calls routines to setup link
  * Leaves the transmit and receive units disabled and uninitialized.
  */
@@ -669,6 +667,7 @@ s32 atl1_init_hw(struct atl1_hw *hw)
  */
 s32 atl1_get_speed_and_duplex(struct atl1_hw *hw, u16 *speed, u16 *duplex)
 {
+	struct pci_dev *pdev = hw->back->pdev;
 	s32 ret_val;
 	u16 phy_data;
 
@@ -691,8 +690,7 @@ s32 atl1_get_speed_and_duplex(struct atl1_hw *hw, u16 *speed, u16 *duplex)
 		*speed = SPEED_10;
 		break;
 	default:
-		printk(KERN_DEBUG "%s: error getting speed\n", 
-			atl1_driver_name);
+		dev_dbg(&pdev->dev, "error getting speed\n");
 		return ATL1_ERR_PHY_SPEED;
 		break;
 	}
diff --git a/drivers/net/atl1/atl1_main.c b/drivers/net/atl1/atl1_main.c
index 4b1d4d153ecf..d28f88bbdd5f 100644
--- a/drivers/net/atl1/atl1_main.c
+++ b/drivers/net/atl1/atl1_main.c
@@ -188,8 +188,7 @@ s32 atl1_setup_ring_resources(struct atl1_adapter *adapter)
 	size = sizeof(struct atl1_buffer) * (tpd_ring->count + rfd_ring->count);
 	tpd_ring->buffer_info = kzalloc(size, GFP_KERNEL);
 	if (unlikely(!tpd_ring->buffer_info)) {
-		printk(KERN_WARNING "%s: kzalloc failed , size = D%d\n",
-			atl1_driver_name, size);
+		dev_err(&pdev->dev, "kzalloc failed , size = D%d\n", size);
 		goto err_nomem;
 	}
 	rfd_ring->buffer_info =
@@ -207,9 +206,7 @@ s32 atl1_setup_ring_resources(struct atl1_adapter *adapter)
 	ring_header->desc = pci_alloc_consistent(pdev, ring_header->size,
 						&ring_header->dma);
 	if (unlikely(!ring_header->desc)) {
-		printk(KERN_WARNING
-			"%s: pci_alloc_consistent failed, size = D%d\n",
-			atl1_driver_name, size);
+		dev_err(&pdev->dev, "pci_alloc_consistent failed\n");
 		goto err_nomem;
 	}
 
@@ -373,8 +370,7 @@ static void atl1_rx_checksum(struct atl1_adapter *adapter,
 		if (rrd->err_flg & (ERR_FLAG_CRC | ERR_FLAG_TRUNC |
 					ERR_FLAG_CODE | ERR_FLAG_OV)) {
 			adapter->hw_csum_err++;
-			printk(KERN_DEBUG "%s: rx checksum error\n",
-				atl1_driver_name);
+			dev_dbg(&adapter->pdev->dev, "rx checksum error\n");
 			return;
 		}
 	}
@@ -393,8 +389,9 @@ static void atl1_rx_checksum(struct atl1_adapter *adapter,
 	}
 
 	/* IPv4, but hardware thinks its checksum is wrong */
-	printk(KERN_DEBUG "%s: hw csum wrong pkt_flag:%x, err_flag:%x\n",
-		atl1_driver_name, rrd->pkt_flg, rrd->err_flg);
+	dev_dbg(&adapter->pdev->dev,
+		"hw csum wrong, pkt_flag:%x, err_flag:%x\n",
+		rrd->pkt_flg, rrd->err_flg);
 	skb->ip_summed = CHECKSUM_COMPLETE;
 	skb->csum = htons(rrd->xsz.xsum_sz.rx_chksum);
 	adapter->hw_csum_err++;
@@ -507,14 +504,13 @@ chk_rrd:
 			/* rrd seems to be bad */
 			if (unlikely(i-- > 0)) {
 				/* rrd may not be DMAed completely */
-				printk(KERN_DEBUG
-					"%s: RRD may not be DMAed completely\n",
-					atl1_driver_name);
+				dev_dbg(&adapter->pdev->dev,
+					"incomplete RRD DMA transfer\n");
 				udelay(1);
 				goto chk_rrd;
 			}
 			/* bad rrd */
-			printk(KERN_DEBUG "%s: bad RRD\n", atl1_driver_name);
+			dev_dbg(&adapter->pdev->dev, "bad RRD\n");
 			/* see if update RFD index */
 			if (rrd->num_buf > 1) {
 				u16 num_buf;
@@ -685,8 +681,8 @@ static void atl1_check_for_link(struct atl1_adapter *adapter)
 	/* notify upper layer link down ASAP */
 	if (!(phy_data & BMSR_LSTATUS)) {	/* Link Down */
 		if (netif_carrier_ok(netdev)) {	/* old link state: Up */
-			printk(KERN_INFO "%s: %s link is down\n",
-			       atl1_driver_name, netdev->name);
+			dev_info(&adapter->pdev->dev, "%s link is down\n",
+				netdev->name);
 			adapter->link_speed = SPEED_0;
 			netif_carrier_off(netdev);
 			netif_stop_queue(netdev);
@@ -731,8 +727,8 @@ static irqreturn_t atl1_intr(int irq, void *data)
 
 		/* check if PCIE PHY Link down */
 		if (status & ISR_PHY_LINKDOWN) {
-			printk(KERN_DEBUG "%s: pcie phy link down %x\n",
-				atl1_driver_name, status);
+			dev_dbg(&adapter->pdev->dev, "pcie phy link down %x\n",
+				status);
 			if (netif_running(adapter->netdev)) {	/* reset MAC */
 				iowrite32(0, adapter->hw.hw_addr + REG_IMR);
 				schedule_work(&adapter->pcie_dma_to_rst_task);
@@ -742,9 +738,9 @@ static irqreturn_t atl1_intr(int irq, void *data)
 
 		/* check if DMA read/write error ? */
 		if (status & (ISR_DMAR_TO_RST | ISR_DMAW_TO_RST)) {
-			printk(KERN_DEBUG
-				"%s: pcie DMA r/w error (status = 0x%x)\n",
-				atl1_driver_name, status);
+			dev_dbg(&adapter->pdev->dev,
+				"pcie DMA r/w error (status = 0x%x)\n",
+				status);
 			iowrite32(0, adapter->hw.hw_addr + REG_IMR);
 			schedule_work(&adapter->pcie_dma_to_rst_task);
 			return IRQ_HANDLED;
@@ -762,14 +758,13 @@ static irqreturn_t atl1_intr(int irq, void *data)
 
 		/* rx exception */
 		if (unlikely(status & (ISR_RXF_OV | ISR_RFD_UNRUN |
+			ISR_RRD_OV | ISR_HOST_RFD_UNRUN |
+			ISR_HOST_RRD_OV | ISR_CMB_RX))) {
+			if (status & (ISR_RXF_OV | ISR_RFD_UNRUN |
 				ISR_RRD_OV | ISR_HOST_RFD_UNRUN |
-				ISR_HOST_RRD_OV | ISR_CMB_RX))) {
-			if (status &
-			    (ISR_RXF_OV | ISR_RFD_UNRUN | ISR_RRD_OV |
-			     ISR_HOST_RFD_UNRUN | ISR_HOST_RRD_OV))
-				printk(KERN_INFO
-					"%s: rx exception: status = 0x%x\n",
-					atl1_driver_name, status);
+				ISR_HOST_RRD_OV))
+				dev_dbg(&adapter->pdev->dev,
+					"rx exception, ISR = 0x%x\n", status);
 			atl1_intr_rx(adapter);
 		}
 
@@ -874,8 +869,7 @@ static u32 atl1_check_link(struct atl1_adapter *adapter)
 	atl1_read_phy_reg(hw, MII_BMSR, &phy_data);
 	if (!(phy_data & BMSR_LSTATUS)) {	/* link down */
 		if (netif_carrier_ok(netdev)) {	/* old link state: Up */
-			printk(KERN_INFO "%s: link is down\n",
-				atl1_driver_name);
+			dev_info(&adapter->pdev->dev, "link is down\n");
 			adapter->link_speed = SPEED_0;
 			netif_carrier_off(netdev);
 			netif_stop_queue(netdev);
@@ -918,11 +912,11 @@ static u32 atl1_check_link(struct atl1_adapter *adapter)
 			adapter->link_speed = speed;
 			adapter->link_duplex = duplex;
 			atl1_setup_mac_ctrl(adapter);
-			printk(KERN_INFO "%s: %s link is up %d Mbps %s\n",
-			       atl1_driver_name, netdev->name,
-			       adapter->link_speed,
-			       adapter->link_duplex ==
-			       FULL_DUPLEX ? "full duplex" : "half duplex");
+			dev_info(&adapter->pdev->dev,
+				"%s link is up %d Mbps %s\n",
+				netdev->name, adapter->link_speed,
+				adapter->link_duplex == FULL_DUPLEX ?
+				"full duplex" : "half duplex");
 		}
 		if (!netif_carrier_ok(netdev)) {	/* Link down -> Up */
 			netif_carrier_on(netdev);
@@ -1330,8 +1324,8 @@ static int atl1_tx_csum(struct atl1_adapter *adapter, struct sk_buff *skb,
 		cso = skb_transport_offset(skb);
 		css = cso + skb->csum_offset;
 		if (unlikely(cso & 0x1)) {
-			printk(KERN_DEBUG "%s: payload offset != even number\n",
-				atl1_driver_name);
+			dev_dbg(&adapter->pdev->dev,
+				"payload offset not an even number\n");
 			return -1;
 		}
 		csum->csumpl |= (cso & CSUM_PARAM_PLOADOFFSET_MASK) <<
@@ -1579,7 +1573,7 @@ static int atl1_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
 	if (!spin_trylock(&adapter->lock)) {
 		/* Can't get lock - tell upper layer to requeue */
 		local_irq_restore(flags);
-		printk(KERN_DEBUG "%s: TX locked\n", atl1_driver_name);
+		dev_dbg(&adapter->pdev->dev, "tx locked\n");
 		return NETDEV_TX_LOCKED;
 	}
 
@@ -1587,7 +1581,7 @@ static int atl1_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
 		/* not enough descriptors */
 		netif_stop_queue(netdev);
 		spin_unlock_irqrestore(&adapter->lock, flags);
-		printk(KERN_DEBUG "%s: TX busy\n", atl1_driver_name);
+		dev_dbg(&adapter->pdev->dev, "tx busy\n");
 		return NETDEV_TX_BUSY;
 	}
 
@@ -1841,8 +1835,7 @@ static int atl1_change_mtu(struct net_device *netdev, int new_mtu)
 
 	if ((max_frame < MINIMUM_ETHERNET_FRAME_SIZE) ||
 	    (max_frame > MAX_JUMBO_FRAME_SIZE)) {
-		printk(KERN_WARNING "%s: invalid MTU setting\n",
-			atl1_driver_name);
+		dev_warn(&adapter->pdev->dev, "invalid MTU setting\n");
 		return -EINVAL;
 	}
 
@@ -2136,9 +2129,7 @@ static int __devinit atl1_probe(struct pci_dev *pdev,
 	if (err) {
 		err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
 		if (err) {
-			printk(KERN_DEBUG
-				"%s: no usable DMA configuration, aborting\n",
-				atl1_driver_name);
+			dev_err(&pdev->dev, "no usable DMA configuration\n");
 			goto err_dma;
 		}
 		pci_using_64 = false;
@@ -2175,7 +2166,9 @@ static int __devinit atl1_probe(struct pci_dev *pdev,
 		goto err_pci_iomap;
 	}
 	/* get device revision number */
-	adapter->hw.dev_rev = ioread16(adapter->hw.hw_addr + (REG_MASTER_CTRL + 2));
+	adapter->hw.dev_rev = ioread16(adapter->hw.hw_addr +
+					(REG_MASTER_CTRL + 2));
+	dev_info(&pdev->dev, "version %s\n", DRIVER_VERSION);
 
 	/* set default ring resource counts */
 	adapter->rfd_ring.count = adapter->rrd_ring.count = ATL1_DEFAULT_RFD;
@@ -2466,8 +2459,6 @@ static void __exit atl1_exit_module(void)
  */
 static int __init atl1_init_module(void)
 {
-	printk(KERN_INFO "%s - version %s\n", atl1_driver_string, DRIVER_VERSION);
-	printk(KERN_INFO "%s\n", atl1_copyright);
 	return pci_register_driver(&atl1_driver);
 }
 
diff --git a/drivers/net/atl1/atl1_param.c b/drivers/net/atl1/atl1_param.c
index bcd0bd891722..4246bb9bd50e 100644
--- a/drivers/net/atl1/atl1_param.c
+++ b/drivers/net/atl1/atl1_param.c
@@ -23,6 +23,7 @@
 
 #include <linux/types.h>
 #include <linux/moduleparam.h>
+#include <linux/pci.h>
 #include "atl1.h"
 
 /*
@@ -93,7 +94,7 @@ struct atl1_option {
 	} arg;
 };
 
-static int __devinit atl1_validate_option(int *value, struct atl1_option *opt)
+static int __devinit atl1_validate_option(int *value, struct atl1_option *opt, struct pci_dev *pdev)
 {
 	if (*value == OPTION_UNSET) {
 		*value = opt->def;
@@ -104,19 +105,17 @@ static int __devinit atl1_validate_option(int *value, struct atl1_option *opt)
 	case enable_option:
 		switch (*value) {
 		case OPTION_ENABLED:
-			printk(KERN_INFO "%s: %s Enabled\n", atl1_driver_name,
-				opt->name);
+			dev_info(&pdev->dev, "%s enabled\n", opt->name);
 			return 0;
 		case OPTION_DISABLED:
-			printk(KERN_INFO "%s: %s Disabled\n", atl1_driver_name,
-				opt->name);
+			dev_info(&pdev->dev, "%s disabled\n", opt->name);
 			return 0;
 		}
 		break;
 	case range_option:
 		if (*value >= opt->arg.r.min && *value <= opt->arg.r.max) {
-			printk(KERN_INFO "%s: %s set to %i\n",
-				atl1_driver_name, opt->name, *value);
+			dev_info(&pdev->dev, "%s set to %i\n", opt->name,
+				*value);
 			return 0;
 		}
 		break;
@@ -128,8 +127,8 @@ static int __devinit atl1_validate_option(int *value, struct atl1_option *opt)
 				ent = &opt->arg.l.p[i];
 				if (*value == ent->i) {
 					if (ent->str[0] != '\0')
-						printk(KERN_INFO "%s: %s\n",
-						       atl1_driver_name, ent->str);
+						dev_info(&pdev->dev, "%s\n",
+							ent->str);
 					return 0;
 				}
 			}
@@ -140,8 +139,8 @@ static int __devinit atl1_validate_option(int *value, struct atl1_option *opt)
 		break;
 	}
 
-	printk(KERN_INFO "%s: invalid %s specified (%i) %s\n",
-	       atl1_driver_name, opt->name, *value, opt->err);
+	dev_info(&pdev->dev, "invalid %s specified (%i) %s\n",
+		opt->name, *value, opt->err);
 	*value = opt->def;
 	return -1;
 }
@@ -157,12 +156,11 @@ static int __devinit atl1_validate_option(int *value, struct atl1_option *opt)
  */
 void __devinit atl1_check_options(struct atl1_adapter *adapter)
 {
+	struct pci_dev *pdev = adapter->pdev;
 	int bd = adapter->bd_number;
 	if (bd >= ATL1_MAX_NIC) {
-		printk(KERN_NOTICE "%s: warning: no configuration for board #%i\n",
-			atl1_driver_name, bd);
-		printk(KERN_NOTICE "%s: using defaults for all values\n",
-			atl1_driver_name);
+		dev_notice(&pdev->dev, "no configuration for board#%i\n", bd);
+		dev_notice(&pdev->dev, "using defaults for all values\n");
 	}
 	{			/* Interrupt Moderate Timer */
 		struct atl1_option opt = {
@@ -177,7 +175,7 @@ void __devinit atl1_check_options(struct atl1_adapter *adapter)
 		int val;
 		if (num_int_mod_timer > bd) {
 			val = int_mod_timer[bd];
-			atl1_validate_option(&val, &opt);
+			atl1_validate_option(&val, &opt, pdev);
 			adapter->imt = (u16) val;
 		} else
 			adapter->imt = (u16) (opt.def);
@@ -197,7 +195,7 @@ void __devinit atl1_check_options(struct atl1_adapter *adapter)
 		int val;
 		if (num_flash_vendor > bd) {
 			val = flash_vendor[bd];
-			atl1_validate_option(&val, &opt);
+			atl1_validate_option(&val, &opt, pdev);
 			adapter->hw.flash_vendor = (u8) val;
 		} else
 			adapter->hw.flash_vendor = (u8) (opt.def);
diff --git a/drivers/net/dm9000.c b/drivers/net/dm9000.c
index 8cc1174e7f64..264fa0e2e075 100644
--- a/drivers/net/dm9000.c
+++ b/drivers/net/dm9000.c
@@ -77,9 +77,6 @@
 
 #define DM9000_PHY		0x40	/* PHY address 0x01 */
 
-#define TRUE			1
-#define FALSE			0
-
 #define CARDNAME "dm9000"
 #define PFX CARDNAME ": "
 
@@ -601,7 +598,7 @@ dm9000_probe(struct platform_device *pdev)
 	printk("%s: not found (%d).\n", CARDNAME, ret);
 
 	dm9000_release_board(pdev, db);
-	kfree(ndev);
+	free_netdev(ndev);
 
 	return ret;
 }
@@ -896,7 +893,7 @@ dm9000_rx(struct net_device *dev)
 	struct dm9000_rxhdr rxhdr;
 	struct sk_buff *skb;
 	u8 rxbyte, *rdptr;
-	int GoodPacket;
+	bool GoodPacket;
 	int RxLen;
 
 	/* Check packet ready or not */
@@ -918,7 +915,7 @@ dm9000_rx(struct net_device *dev)
 			return;
 
 		/* A packet ready now  & Get status/length */
-		GoodPacket = T