Merge tag 'qcom-arm64-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt

Qualcomm ARM64 DT updates for v5.8

For SDM845 this defines the IPA network accelerator and the CCI camera
control bus, it defines the required UFS reset and adds WiFi for the
Lenovo Yoga C630 and defines GPIO pin names and adds OV8856 and OC7251
camera nodes for DB845c.

For SC7180 it adds GPU support, defines the modem remoteproc, adds the
IPA network accelerator, Coresight and ETM support, adds cpuidle low
power states and updates the CPUs' compatible.

For SM8250 it adds regulators from the PM8150, PM8150L and PM8009 and
adds voltage corners, it defines the nodes for UFS PHY and controller
and finally corrects a typo in the PDC node to make SPMI functional.

For MSM8916 I2C1 and I2C5 are defined, a node for the CCI camera control
interface bus is added and Coresight is disabled by default to match
some product configurations. The Samsung A3U gained display support and
Samsung A5U gained touchscreen support.

MSM8996 now property describes the power supply chain for the GPU, the
CCI camera control interface bus is added and the DB820c has the
regulators of the secondary PMIC defined.

For QCS404 USB PHYs and controllers are defined and wired up for the
EVB.

SDM630/SDM660 platform support is added and the Xiaomi Redmi Note 7
defined.

It also contains a number of changes throughout to improve DT binding
compliance.

* tag 'qcom-arm64-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (68 commits)
  arm64: dts: qcom: sc7180: Correct the pdc interrupt ranges
  arm64: dts: qcom: sc7180: add IPA information
  arm64: dts: qcom: sc7180: Fix ETMv4 power management patch
  arm64: dts: qcom: sc7180: Add A618 gpu dt blob
  dt-bindings: arm-smmu: Add sc7180 compatible string
  arm64: dts: qcom: msm8996: Make GPU node control GPU_GX GDSC
  arm64: dts: qcom: db820c: Add vdd_gfx and tie it into mmcc
  arm64: dts: qcom: apq8016-sbc: merge -pins.dtsi into main .dtsi
  arm64: dts: qcom: msm8916: move gpu opp table to gpu node
  arm64: dts: qcom: msm8916: avoid using _ in node names
  arm64: dts: qcom: c630: Specify UFS device reset
  arm64: dts: qcom: c630: Add WiFi node
  arm64: dts: qcom: msm8916-samsung-a3u: add nodes for display panel
  arm64: dts: qcom: db820c: Fix invalid pm8994 supplies
  arm64: dts: qcom: db820c: Add pmi8994 RPM regulators
  arm64: dts: qcom: msm8916: Disable coresight by default
  arm64: dts: qcom: sc7180: Add "no-map" to cmd_db reserved area
  arm64: dts: qcom: msm8916-samsung-a5u: Add touchscreen
  arm64: dts: qcom: msm8916-samsung-a2015: Add touchscreen regulator
  arm64: dts: qcom: msm8916: Add blsp_i2c5
  ...

Link: https://lore.kernel.org/r/20200519052528.1249950-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

32 files changed, 3519 insertions, 801 deletions

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index cc103f7020fd..0f2c33d611df 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-hp-envy-x2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-lenovo-miix-630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm660-xiaomi-lavender.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc-pmic-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc-pmic-pins.dtsi
deleted file mode 100644
index aff218c1b7b6..000000000000
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc-pmic-pins.dtsi
+++ /dev/null
@@ -1,74 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
-
-&pm8916_gpios {
-
-	usb_hub_reset_pm: usb_hub_reset_pm {
-		pinconf {
-			pins = "gpio3";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			input-disable;
-			output-high;
-		};
-	};
-
-	usb_hub_reset_pm_device: usb_hub_reset_pm_device {
-		pinconf {
-			pins = "gpio3";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			output-low;
-		};
-	};
-
-	usb_sw_sel_pm: usb_sw_sel_pm {
-		pinconf {
-			pins = "gpio4";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			power-source = <PM8916_GPIO_VPH>;
-			input-disable;
-			output-high;
-		};
-	};
-
-	usb_sw_sel_pm_device: usb_sw_sel_pm_device {
-		pinconf {
-			pins = "gpio4";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			power-source = <PM8916_GPIO_VPH>;
-			input-disable;
-			output-low;
-		};
-	};
-
-	pm8916_gpios_leds: pm8916_gpios_leds {
-		pinconf {
-			pins = "gpio1", "gpio2";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			output-low;
-		};
-	};
-};
-
-&pm8916_mpps {
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&ls_exp_gpio_f>;
-
-	ls_exp_gpio_f: pm8916_mpp4 {
-		pinconf {
-			pins = "mpp4";
-			function = "digital";
-			output-low;
-			power-source = <PM8916_MPP_L5>;	// 1.8V
-		};
-	};
-
-	pm8916_mpps_leds: pm8916_mpps_leds {
-		pinconf {
-			pins = "mpp2", "mpp3";
-			function = "digital";
-			output-low;
-		};
-	};
-};
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi
deleted file mode 100644
index 21d0822f1ca6..000000000000
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi
+++ /dev/null
@@ -1,89 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-
-#include <dt-bindings/gpio/gpio.h>
-
-&msmgpio {
-
-	msmgpio_leds: msmgpio_leds {
-		pinconf {
-			pins = "gpio21", "gpio120";
-			function = "gpio";
-			output-low;
-		};
-	};
-
-	usb_id_default: usb-id-default {
-		pinmux {
-			function = "gpio";
-			pins = "gpio121";
-		};
-
-		pinconf {
-			pins = "gpio121";
-			drive-strength = <8>;
-			input-enable;
-			bias-pull-up;
-		};
-	};
-
-	adv7533_int_active: adv533_int_active {
-		pinmux {
-			function = "gpio";
-			pins = "gpio31";
-		};
-		pinconf {
-			pins = "gpio31";
-			drive-strength = <16>;
-			bias-disable;
-		};
-	};
-
-	adv7533_int_suspend: adv7533_int_suspend {
-		pinmux {
-			function = "gpio";
-			pins = "gpio31";
-		};
-		pinconf {
-			pins = "gpio31";
-			drive-strength = <2>;
-			bias-disable;
-		};
-	};
-
-	adv7533_switch_active: adv7533_switch_active {
-		pinmux {
-			function = "gpio";
-			pins = "gpio32";
-		};
-		pinconf {
-			pins = "gpio32";
-			drive-strength = <16>;
-			bias-disable;
-		};
-	};
-
-	adv7533_switch_suspend: adv7533_switch_suspend {
-		pinmux {
-			function = "gpio";
-			pins = "gpio32";
-		};
-		pinconf {
-			pins = "gpio32";
-			drive-strength = <2>;
-			bias-disable;
-		};
-	};
-
-	msm_key_volp_n_default: msm_key_volp_n_default {
-		pinmux {
-			function = "gpio";
-			pins = "gpio107";
-		};
-		pinconf {
-			pins = "gpio107";
-			drive-strength = <8>;
-			input-enable;
-			bias-pull-up;
-		};
-	};
-};
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index 06aab44d798c..8a4b790aa7ff 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -5,10 +5,10 @@
 
 #include "msm8916.dtsi"
 #include "pm8916.dtsi"
-#include "apq8016-sbc-soc-pins.dtsi"
-#include "apq8016-sbc-pmic-pins.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
 #include <dt-bindings/sound/apq8016-lpass.h>
 
 /*
@@ -51,6 +51,30 @@
 		stdout-path = "serial0";
 	};
 
+	camera_vdddo_1v8: camera-vdddo-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vdddo";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	camera_vdda_2v8: camera-vdda-2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vdda";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+
+	camera_vddd_1v5: camera-vddd-1v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vddd";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+	};
+
 	reserved-memory {
 		ramoops@bff00000{
 			compatible = "ramoops";
@@ -495,6 +519,27 @@
 		wcnss@a21b000 {
 			status = "okay";
 		};
+
+		tpiu@820000 { status = "okay"; };
+		funnel@821000 { status = "okay"; };
+		replicator@824000 { status = "okay"; };
+		etf@825000 { status = "okay"; };
+		etr@826000 { status = "okay"; };
+		funnel@841000 { status = "okay"; };
+		debug@850000 { status = "okay"; };
+		debug@852000 { status = "okay"; };
+		debug@854000 { status = "okay"; };
+		debug@856000 { status = "okay"; };
+		etm@85c000 { status = "okay"; };
+		etm@85d000 { status = "okay"; };
+		etm@85e000 { status = "okay"; };
+		etm@85f000 { status = "okay"; };
+		cti@810000 { status = "okay"; };
+		cti@811000 { status = "okay"; };
+		cti@858000 { status = "okay"; };
+		cti@859000 { status = "okay"; };
+		cti@85a000 { status = "okay"; };
+		cti@85b000 { status = "okay"; };
 	};
 
 	usb2513 {
@@ -521,7 +566,7 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -538,6 +583,58 @@
 	};
 };
 
+&camss {
+	status = "ok";
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		port@0 {
+			reg = <0>;
+			csiphy0_ep: endpoint {
+				clock-lanes = <1>;
+				data-lanes = <0 2>;
+				remote-endpoint = <&ov5640_ep>;
+				status = "okay";
+			};
+		};
+	};
+};
+
+&cci {
+	status = "ok";
+};
+
+&cci_i2c0 {
+	camera_rear@3b {
+		compatible = "ovti,ov5640";
+		reg = <0x3b>;
+
+		enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&camera_rear_default>;
+
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "xclk";
+		clock-frequency = <23880000>;
+
+		vdddo-supply = <&camera_vdddo_1v8>;
+		vdda-supply = <&camera_vdda_2v8>;
+		vddd-supply = <&camera_vddd_1v5>;
+
+		/* No camera mezzanine by default */
+		status = "disabled";
+
+		port {
+			ov5640_ep: endpoint {
+				clock-lanes = <1>;
+				data-lanes = <0 2>;
+				remote-endpoint = <&csiphy0_ep>;
+			};
+		};
+	};
+};
+
 &spmi_bus {
 	pm8916_0: pm8916@0 {
 		pon@800 {
@@ -680,3 +777,157 @@
 		regulator-max-microvolt = <3337000>;
 	};
 };
+
+&msmgpio {
+	msmgpio_leds: msmgpio-leds {
+		pinconf {
+			pins = "gpio21", "gpio120";
+			function = "gpio";
+			output-low;
+		};
+	};
+
+	usb_id_default: usb-id-default {
+		pinmux {
+			function = "gpio";
+			pins = "gpio121";
+		};
+
+		pinconf {
+			pins = "gpio121";
+			drive-strength = <8>;
+			input-enable;
+			bias-pull-up;
+		};
+	};
+
+	adv7533_int_active: adv533-int-active {
+		pinmux {
+			function = "gpio";
+			pins = "gpio31";
+		};
+		pinconf {
+			pins = "gpio31";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	adv7533_int_suspend: adv7533-int-suspend {
+		pinmux {
+			function = "gpio";
+			pins = "gpio31";
+		};
+		pinconf {
+			pins = "gpio31";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	adv7533_switch_active: adv7533-switch-active {
+		pinmux {
+			function = "gpio";
+			pins = "gpio32";
+		};
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	adv7533_switch_suspend: adv7533-switch-suspend {
+		pinmux {
+			function = "gpio";
+			pins = "gpio32";
+		};
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	msm_key_volp_n_default: msm-key-volp-n-default {
+		pinmux {
+			function = "gpio";
+			pins = "gpio107";
+		};
+		pinconf {
+			pins = "gpio107";
+			drive-strength = <8>;
+			input-enable;
+			bias-pull-up;
+		};
+	};
+};
+
+&pm8916_gpios {
+	usb_hub_reset_pm: usb-hub-reset-pm {
+		pinconf {
+			pins = "gpio3";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			input-disable;
+			output-high;
+		};
+	};
+
+	usb_hub_reset_pm_device: usb-hub-reset-pm-device {
+		pinconf {
+			pins = "gpio3";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			output-low;
+		};
+	};
+
+	usb_sw_sel_pm: usb-sw-sel-pm {
+		pinconf {
+			pins = "gpio4";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			power-source = <PM8916_GPIO_VPH>;
+			input-disable;
+			output-high;
+		};
+	};
+
+	usb_sw_sel_pm_device: usb-sw-sel-pm-device {
+		pinconf {
+			pins = "gpio4";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			power-source = <PM8916_GPIO_VPH>;
+			input-disable;
+			output-low;
+		};
+	};
+
+	pm8916_gpios_leds: pm8916-gpios-leds {
+		pinconf {
+			pins = "gpio1", "gpio2";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			output-low;
+		};
+	};
+};
+
+&pm8916_mpps {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ls_exp_gpio_f>;
+
+	ls_exp_gpio_f: pm8916-mpp4 {
+		pinconf {
+			pins = "mpp4";
+			function = "digital";
+			output-low;
+			power-source = <PM8916_MPP_L5>;	// 1.8V
+		};
+	};
+
+	pm8916_mpps_leds: pm8916-mpps-leds {
+		pinconf {
+			pins = "mpp2", "mpp3";
+			function = "digital";
+			output-low;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index af87350b5547..a5abd3d115ea 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -117,16 +117,6 @@
 		regulator-max-microvolt = <3700000>;
 	};
 
-	vreg_s8a_l3a_input: vreg-s8a-l3a-input {
-		compatible = "regulator-fixed";
-		regulator-name = "vreg_s8a_l3a_input";
-		regulator-always-on;
-		regulator-boot-on;
-
-		regulator-min-microvolt = <0>;
-		regulator-max-microvolt = <0>;
-	};
-
 	wlan_en: wlan-en-1-8v {
 		pinctrl-names = "default";
 		pinctrl-0 = <&wlan_en_gpios>;
@@ -251,6 +241,10 @@
 	status = "okay";
 };
 
+&mmcc {
+	vdd-gfx-supply = <&vdd_gfx>;
+};
+
 &msmgpio {
 	gpio-line-names =
 		"[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */
@@ -688,6 +682,15 @@
 	};
 };
 
+&pmi8994_spmi_regulators {
+	vdd_gfx: s2@1700 {
+		reg = <0x1700 0x100>;
+		regulator-name = "VDD_GFX";
+		regulator-min-microvolt = <980000>;
+		regulator-max-microvolt = <980000>;
+	};
+};
+
 &rpm_requests {
 	pm8994-regulators {
 		compatible = "qcom,rpm-pm8994-regulators";
@@ -704,15 +707,20 @@
 		vdd_s10-supply = <&vph_pwr>;
 		vdd_s11-supply = <&vph_pwr>;
 		vdd_s12-supply = <&vph_pwr>;
+		vdd_l1-supply = <&vreg_s1b_1p025>;
 		vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>;
-		vdd_l3_l11-supply = <&vreg_s8a_l3a_input>;
+		vdd_l3_l11-supply = <&vreg_s3a_1p3>;
 		vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>;
 		vdd_l5_l7-supply = <&vreg_s5a_2p15>;
 		vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>;
 		vdd_l8_l16_l30-supply = <&vph_pwr>;
+		vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>;
+		vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>;
 		vdd_l14_l15-supply = <&vreg_s5a_2p15>;
+		vdd_l17_l29-supply = <&vph_pwr_bbyp>;
+		vdd_l20_l21-supply = <&vph_pwr_bbyp>;
 		vdd_l25-supply = <&vreg_s3a_1p3>;
-		vdd_lvs1_2-supply = <&vreg_s4a_1p8>;
+		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
 
 		vreg_s3a_1p3: s3 {
 			regulator-name = "vreg_s3a_1p3";
@@ -895,6 +903,27 @@
 			regulator-name = "vreg_lvs2a_1p8";
 		};
 	};
+
+	pmi8994-regulators {
+		compatible = "qcom,rpm-pmi8994-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_bst_byp-supply = <&vph_pwr>;
+
+		vph_pwr_bbyp: boost-bypass {
+			regulator-name = "vph_pwr_bbyp";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		vreg_s1b_1p025: s1 {
+			regulator-name = "vreg_s1b_1p025";
+			regulator-min-microvolt = <1025000>;
+			regulator-max-microvolt = <1025000>;
+		};
+	};
 };
 
 &sdhc2 {
diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
index 70be3f95209b..6754cb0638f4 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
@@ -24,63 +24,61 @@
 		device_type = "memory";
 		reg = <0x0 0x40000000 0x0 0x20000000>;
 	};
+};
+
+&blsp1_i2c2 {
+	status = "ok";
+};
+
+&blsp1_spi1 {
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&blsp1_uart3 {
+	status = "ok";
+};
+
+&blsp1_uart5 {
+	status = "ok";
+};
+
+&pcie0 {
+	status = "ok";
+	perst-gpio = <&tlmm 61 0x1>;
+};
+
+&pcie1 {
+	status = "ok";
+	perst-gpio = <&tlmm 58 0x1>;
+};
+
+&pcie_phy0 {
+	status = "ok";
+};
+
+&pcie_phy1 {
+	status = "ok";
+};
+
+&qpic_bam {
+	status = "ok";
+};
+
+&qpic_nand {
+	status = "ok";
 
-	soc {
-		serial@78b3000 {
-			status = "ok";
-		};
-
-		spi@78b5000 {
-			status = "ok";
-
-			m25p80@0 {
-				  #address-cells = <1>;
-				  #size-cells = <1>;
-				  compatible = "jedec,spi-nor";
-				  reg = <0>;
-				  spi-max-frequency = <50000000>;
-			};
-		};
-
-		serial@78b1000 {
-			 status = "ok";
-		};
-
-		i2c@78b6000 {
-			 status = "ok";
-		};
-
-		dma@7984000 {
-			 status = "ok";
-		};
-
-		nand@79b0000 {
-			status = "ok";
-
-			nand@0 {
-				reg = <0>;
-				nand-ecc-strength = <4>;
-				nand-ecc-step-size = <512>;
-				nand-bus-width = <8>;
-			};
-		};
-
-		phy@86000 {
-			status = "ok";
-		};
-
-		phy@8e000 {
-			status = "ok";
-		};
-
-		pci@20000000 {
-			status = "ok";
-			perst-gpio = <&tlmm 58 0x1>;
-		};
-
-		pci@10000000 {
-			status = "ok";
-			perst-gpio = <&tlmm 61 0x1>;
-		};
+	nand@0 {
+		reg = <0>;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 2b31823d3ccd..5303821300b4 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -10,15 +10,111 @@
 	model = "Qualcomm Technologies, Inc. IPQ8074";
 	compatible = "qcom,ipq8074";
 
+	clocks {
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};
+
+		xo: xo {
+			compatible = "fixed-clock";
+			clock-frequency = <19200000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CPU1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+		};
+
+		L2_0: l2-cache {
+			compatible = "cache";
+			cache-level = <0x2>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
 	soc: soc {
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 		ranges = <0 0 0 0xffffffff>;
 		compatible = "simple-bus";
 
+		pcie_phy0: phy@86000 {
+			compatible = "qcom,ipq8074-qmp-pcie-phy";
+			reg = <0x00086000 0x1000>;
+			#phy-cells = <0>;
+			clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
+			clock-names = "pipe_clk";
+			clock-output-names = "pcie20_phy0_pipe_clk";
+
+			resets = <&gcc GCC_PCIE0_PHY_BCR>,
+				<&gcc GCC_PCIE0PHY_PHY_BCR>;
+			reset-names = "phy",
+				      "common";
+			status = "disabled";
+		};
+
+		pcie_phy1: phy@8e000 {
+			compatible = "qcom,ipq8074-qmp-pcie-phy";
+			reg = <0x0008e000 0x1000>;
+			#phy-cells = <0>;
+			clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
+			clock-names = "pipe_clk";
+			clock-output-names = "pcie20_phy1_pipe_clk";
+
+			resets = <&gcc GCC_PCIE1_PHY_BCR>,
+				<&gcc GCC_PCIE1PHY_PHY_BCR>;
+			reset-names = "phy",
+				      "common";
+			status = "disabled";
+		};
+
 		tlmm: pinctrl@1000000 {
 			compatible = "qcom,ipq8074-pinctrl";
-			reg = <0x1000000 0x300000>;
+			reg = <0x01000000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
 			gpio-ranges = <&tlmm 0 0 70>;
@@ -66,102 +162,16 @@
 			};
 		};
 
-		intc: interrupt-controller@b000000 {
-			compatible = "qcom,msm-qgic2";
-			interrupt-controller;
-			#interrupt-cells = <0x3>;
-			reg = <0xb000000 0x1000>, <0xb002000 0x1000>;
-		};
-
-		timer {
-			compatible = "arm,armv8-timer";
-			interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
-		};
-
-		timer@b120000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			compatible = "arm,armv7-timer-mem";
-			reg = <0xb120000 0x1000>;
-			clock-frequency = <19200000>;
-
-			frame@b120000 {
-				frame-number = <0>;
-				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb121000 0x1000>,
-				      <0xb122000 0x1000>;
-			};
-
-			frame@b123000 {
-				frame-number = <1>;
-				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb123000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@b124000 {
-				frame-number = <2>;
-				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb124000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@b125000 {
-				frame-number = <3>;
-				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb125000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@b126000 {
-				frame-number = <4>;
-				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb126000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@b127000 {
-				frame-number = <5>;
-				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb127000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@b128000 {
-				frame-number = <6>;
-				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb128000 0x1000>;
-				status = "disabled";
-			};
-		};
-
 		gcc: gcc@1800000 {
 			compatible = "qcom,gcc-ipq8074";
-			reg = <0x1800000 0x80000>;
+			reg = <0x01800000 0x80000>;
 			#clock-cells = <0x1>;
 			#reset-cells = <0x1>;
 		};
 
-		blsp1_uart5: serial@78b3000 {
-			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-			reg = <0x78b3000 0x200>;
-			interrupts = <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&