/*
* Interface handling (except master interface)
*
* Copyright 2002-2005, Instant802 Networks, Inc.
* Copyright 2005-2006, Devicescape Software, Inc.
* Copyright (c) 2006 Jiri Benc <jbenc@suse.cz>
* Copyright 2008, Johannes Berg <johannes@sipsolutions.net>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/if_arp.h>
#include <linux/netdevice.h>
#include <linux/rtnetlink.h>
#include <net/mac80211.h>
#include "ieee80211_i.h"
#include "sta_info.h"
#include "debugfs_netdev.h"
#include "mesh.h"
#include "led.h"
#include "driver-ops.h"
/**
* DOC: Interface list locking
*
* The interface list in each struct ieee80211_local is protected
* three-fold:
*
* (1) modifications may only be done under the RTNL
* (2) modifications and readers are protected against each other by
* the iflist_mtx.
* (3) modifications are done in an RCU manner so atomic readers
* can traverse the list in RCU-safe blocks.
*
* As a consequence, reads (traversals) of the list can be protected
* by either the RTNL, the iflist_mtx or RCU.
*/
static int ieee80211_change_mtu(struct net_device *dev, int new_mtu)
{
int meshhdrlen;
struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
meshhdrlen = (sdata->vif.type == NL80211_IFTYPE_MESH_POINT) ? 5 : 0;
/* FIX: what would be proper limits for MTU?
* This interface uses 802.3 frames. */
if (new_mtu < 256 ||
new_mtu > IEEE80211_MAX_DATA_LEN - 24 - 6 - meshhdrlen) {
return -EINVAL;
}
#ifdef CONFIG_MAC80211_VERBOSE_DEBUG
printk(KERN_DEBUG "%s: setting MTU %d\n", dev->name, new_mtu);
#endif /* CONFIG_MAC80211_VERBOSE_DEBUG */
dev->mtu = new_mtu;
return 0;
}
static inline int identical_mac_addr_allowed(int type1, int type2)
{
return type1 == NL80211_IFTYPE_MONITOR ||
type2 == NL80211_IFTYPE_MONITOR ||
(type1 == NL80211_IFTYPE_AP && type2 == NL80211_IFTYPE_WDS) ||
(type1 == NL80211_IFTYPE_WDS &&
(type2 == NL80211_IFTYPE_WDS ||
type2 == NL80211_IFTYPE_AP)) ||
(type1 == NL80211_IFTYPE_AP && type2 == NL80211_IFTYPE_AP_VLAN) ||
(type1 == NL80211_IFTYPE_AP_VLAN &&
(type2 == NL80211_IFTYPE_AP ||
type2 == NL80211_IFTYPE_AP_VLAN));
}
static int ieee80211_open(struct net_device *dev)
{
struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
struct ieee80211_sub_if_data *nsdata;
struct ieee80211_local *local = sdata->local;
struct sta_info *sta;
struct ieee80211_if_init_conf conf;
u32 changed = 0;
int res;
u32 hw_reconf_flags = 0;
u8 null_addr[ETH_ALEN] = {0};
/* fail early if user set an invalid address */
if (compare_ether_addr(dev->dev_addr, null_addr) &&
!is_valid_ether_addr(dev->dev_addr))
return -EADDRNOTAVAIL;
/* we hold the RTNL here so can safely walk the list */
list_for_each_entry(nsdata, &local->interfaces, list) {
struct net_device *ndev = nsdata->dev;
if (ndev != dev && netif_running(ndev)) {
/*
* Allow only a single IBSS interface to be up at any
* time. This is restricted because beacon distribution
* cannot work properly if both are in the same IBSS.
*
* To remove this restriction we'd have to disallow them
* from setting the same SSID on different IBSS interfaces
* belonging to the same hardware. Then, however, we're
* faced with having to adopt two different TSF timers...
*/
if (sdata->vif.type == NL80211_IFTYPE_ADHOC &&
nsdata->vif.type == NL80211_IFTYPE_ADHOC)
return -EBUSY;
/*
* The remaining checks are only performed for interfaces
* with the same MAC address.
*/
if (compare_ether_addr(dev->dev_addr, ndev->dev_addr))
continue;
/*
* check whether it may have the same address
*/
if (!identical_mac_addr_allowed(sdata->vif.type,
nsdata->vif.type))
return -ENOTUNIQ;
/*
* can only add VLANs to enabled APs
*/
if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN &&
nsdata->vif.type == NL80211_IFTYPE_AP)
sdata->bss = &nsdata->u.ap;
}
}
switch (sdata->vif.type) {
case NL80211_IFTYPE_WDS:
if (!is_valid_ether_addr(sdata->u.wds.remote_addr))
return -ENOLINK;
break;
case NL80211_IFTYPE_AP_VLAN:
if (!sdata->bss)
return -ENOLINK;
list_add(&sdata->u.vlan.list, &sdata->bss->vlans);
break;
case NL80211_IFTYPE_AP:
sdata->bss = &sdata->u.ap;
break;
case NL80211_IFTYPE_MESH_POINT:
if (!ieee80211_vif_is_mesh(&sdata->vif))
break;
/* mesh ifaces must set allmulti to forward mcast traffic */
atomic_inc(&local->iff_allmultis);
break;
case NL80211_IFTYPE_STATION:
case NL80211_IFTYPE_MONITOR:
case NL80211_IFTYPE_ADHOC:
/* no special treatment */
break;
case NL80211_IFTYPE_UNSPECIFIED:
case __NL80211_IFTYPE_AFTER_LAST