path: root/drivers/scsi/megaraid/megaraid_sas.h

/*
 *
 *		Linux MegaRAID driver for SAS based RAID controllers
 *
 * Copyright (c) 2003-2005  LSI Corporation.
 *
 *		This program is free software; you can redistribute it and/or
 *		modify it under the terms of the GNU General Public License
 *		as published by the Free Software Foundation; either version
 *		2 of the License, or (at your option) any later version.
 *
 * FILE		: megaraid_sas.h
 */

#ifndef LSI_MEGARAID_SAS_H
#define LSI_MEGARAID_SAS_H

/*
 * MegaRAID SAS Driver meta data
 */
#define MEGASAS_VERSION				"00.00.03.16-rc1"
#define MEGASAS_RELDATE				"Nov. 07, 2007"
#define MEGASAS_EXT_VERSION			"Thu. Nov. 07 10:09:32 PDT 2007"

/*
 * Device IDs
 */
#define	PCI_DEVICE_ID_LSI_SAS1078R		0x0060
#define	PCI_DEVICE_ID_LSI_VERDE_ZCR		0x0413

/*
 * =====================================
 * MegaRAID SAS MFI firmware definitions
 * =====================================
 */

/*
 * MFI stands for  MegaRAID SAS FW Interface. This is just a moniker for 
 * protocol between the software and firmware. Commands are issued using
 * "message frames"
 */

/*
 * FW posts its state in upper 4 bits of outbound_msg_0 register
 */
#define MFI_STATE_MASK				0xF0000000
#define MFI_STATE_UNDEFINED			0x00000000
#define MFI_STATE_BB_INIT			0x10000000
#define MFI_STATE_FW_INIT			0x40000000
#define MFI_STATE_WAIT_HANDSHAKE		0x60000000
#define MFI_STATE_FW_INIT_2			0x70000000
#define MFI_STATE_DEVICE_SCAN			0x80000000
#define MFI_STATE_BOOT_MESSAGE_PENDING		0x90000000
#define MFI_STATE_FLUSH_CACHE			0xA0000000
#define MFI_STATE_READY				0xB0000000
#define MFI_STATE_OPERATIONAL			0xC0000000
#define MFI_STATE_FAULT				0xF0000000

#define MEGAMFI_FRAME_SIZE			64

/*
 * During FW init, clear pending cmds & reset state using inbound_msg_0
 *
 * ABORT	: Abort all pending cmds
 * READY	: Move from OPERATIONAL to READY state; discard queue info
 * MFIMODE	: Discard (possible) low MFA posted in 64-bit mode (??)
 * CLR_HANDSHAKE: FW is waiting for HANDSHAKE from BIOS or Driver
 * HOTPLUG	: Resume from Hotplug
 * MFI_STOP_ADP	: Send signal to FW to stop processing
 */
#define MFI_INIT_ABORT				0x00000001
#define MFI_INIT_READY				0x00000002
#define MFI_INIT_MFIMODE			0x00000004
#define MFI_INIT_CLEAR_HANDSHAKE		0x00000008
#define MFI_INIT_HOTPLUG			0x00000010
#define MFI_STOP_ADP				0x00000020
#define MFI_RESET_FLAGS				MFI_INIT_READY| \
						MFI_INIT_MFIMODE| \
						MFI_INIT_ABORT

/*
 * MFI frame flags
 */
#define MFI_FRAME_POST_IN_REPLY_QUEUE		0x0000
#define MFI_FRAME_DONT_POST_IN_REPLY_QUEUE	0x0001
#define MFI_FRAME_SGL32				0x0000
#define MFI_FRAME_SGL64				0x0002
#define MFI_FRAME_SENSE32			0x0000
#define MFI_FRAME_SENSE64			0x0004
#define MFI_FRAME_DIR_NONE			0x0000
#define MFI_FRAME_DIR_WRITE			0x0008
#define MFI_FRAME_DIR_READ			0x0010
#define MFI_FRAME_DIR_BOTH			0x0018

/*
 * Definition for cmd_status
 */
#define MFI_CMD_STATUS_POLL_MODE		0xFF

/*
 * MFI command opcodes
 */
#define MFI_CMD_INIT				0x00
#define MFI_CMD_LD_READ				0x01
#define MFI_CMD_LD_WRITE			0x02
#define MFI_CMD_LD_SCSI_IO			0x03
#define MFI_CMD_PD_SCSI_IO			0x04
#define MFI_CMD_DCMD				0x05
#define MFI_CMD_ABORT				0x06
#define MFI_CMD_SMP				0x07
#define MFI_CMD_STP				0x08

#define MR_DCMD_CTRL_GET_INFO			0x01010000

#define MR_DCMD_CTRL_CACHE_FLUSH		0x01101000
#define MR_FLUSH_CTRL_CACHE			0x01
#define MR_FLUSH_DISK_CACHE			0x02

#define MR_DCMD_CTRL_SHUTDOWN			0x01050000
#define MR_DCMD_HIBERNATE_SHUTDOWN		0x01060000
#define MR_ENABLE_DRIVE_SPINDOWN		0x01

#define MR_DCMD_CTRL_EVENT_GET_INFO		0x01040100
#define MR_DCMD_CTRL_EVENT_GET			0x01040300
#define MR_DCMD_CTRL_EVENT_WAIT			0x01040500
#define MR_DCMD_LD_GET_PROPERTIES		0x03030000

#define MR_DCMD_CLUSTER				0x08000000
#define MR_DCMD_CLUSTER_RESET_ALL		0x08010100
#define MR_DCMD_CLUSTER_RESET_LD		0x08010200

/*
 * MFI command completion codes
 */
enum MFI_STAT {
	MFI_STAT_OK = 0x00,
	MFI_STAT_INVALID_CMD = 0x01,
	MFI_STAT_INVALID_DCMD = 0x02,
	MFI_STAT_INVALID_PARAMETER = 0x03,
	MFI_STAT_INVALID_SEQUENCE_NUMBER = 0x04,
	MFI_STAT_ABORT_NOT_POSSIBLE = 0x05,
	MFI_STAT_APP_HOST_CODE_NOT_FOUND = 0x06,
	MFI_STAT_APP_IN_USE = 0x07,
	MFI_STAT_APP_NOT_INITIALIZED = 0x08,
	MFI_STAT_ARRAY_INDEX_INVALID = 0x09,
	MFI_STAT_ARRAY_ROW_NOT_EMPTY = 0x0a,
	MFI_STAT_CONFIG_RESOURCE_CONFLICT = 0x0b,
	MFI_STAT_DEVICE_NOT_FOUND = 0x0c,
	MFI_STAT_DRIVE_TOO_SMALL = 0x0d,
	MFI_STAT_FLASH_ALLOC_FAIL = 0x0e,
	MFI_STAT_FLASH_BUSY = 0x0f,
	MFI_STAT_FLASH_ERROR = 0x10,
	MFI_STAT_FLASH_IMAGE_BAD = 0x11,
	MFI_STAT_FLASH_IMAGE_INCOMPLETE = 0x12,
	MFI_STAT_FLASH_NOT_OPEN = 0x13,
	MFI_STAT_FLASH_NOT_STARTED = 0x14,
	MFI_STAT_FLUSH_FAILED = 0x15,
	MFI_STAT_HOST_CODE_NOT_FOUNT = 0x16,
	MFI_STAT_LD_CC_IN_PROGRESS = 0x17,
	MFI_STAT_LD_INIT_IN_PROGRESS = 0x18,
	MFI_STAT_LD_LBA_OUT_OF_RANGE = 0x19,
	MFI_STAT_LD_MAX_CONFIGURED = 0x1a,
	MFI_STAT_LD_NOT_OPTIMAL = 0x1b,
	MFI_STAT_LD_RBLD_IN_PROGRESS = 0x1c,
	MFI_STAT_LD_RECON_IN_PROGRESS = 0x1d,
	MFI_STAT_LD_WRONG_RAID_LEVEL = 0x1e,
	MFI_STAT_MAX_SPARES_EXCEEDED = 0x1f,
	MFI_STAT_MEMORY_NOT_AVAILABLE = 0x20,
	MFI_STAT_MFC_HW_ERROR = 0x21,
	MFI_STAT_NO_HW_PRESENT = 0x22,
	MFI_STAT_NOT_FOUND = 0x23,
	MFI_STAT_NOT_IN_ENCL = 0x24,
	MFI_STAT_PD_CLEAR_IN_PROGRESS = 0x25,
	MFI_STAT_PD_TYPE_WRONG = 0x26,
	MFI_STAT_PR_DISABLED = 0x27,
	MFI_STAT_ROW_INDEX_INVALID = 0x28,
	MFI_STAT_SAS_CONFIG_INVALID_ACTION = 0x29,
	MFI_STAT_SAS_CONFIG_INVALID_DATA = 0x2a,
	MFI_STAT_SAS_CONFIG_INVALID_PAGE =