/*
* ahci.c - AHCI SATA support
*
* Maintained by: Jeff Garzik <jgarzik@pobox.com>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
* Copyright 2004-2005 Red Hat, Inc.
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2, or (at your option)
* any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; see the file COPYING. If not, write to
* the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
*
*
* libata documentation is available via 'make {ps|pdf}docs',
* as Documentation/DocBook/libata.*
*
* AHCI hardware documentation:
* http://www.intel.com/technology/serialata/pdf/rev1_0.pdf
* http://www.intel.com/technology/serialata/pdf/rev1_1.pdf
*
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/sched.h>
#include <linux/dma-mapping.h>
#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <asm/io.h>
#define DRV_NAME "ahci"
#define DRV_VERSION "1.01"
enum {
AHCI_PCI_BAR = 5,
AHCI_MAX_SG = 168, /* hardware max is 64K */
AHCI_DMA_BOUNDARY = 0xffffffff,
AHCI_USE_CLUSTERING = 0,
AHCI_CMD_SLOT_SZ = 32 * 32,
AHCI_RX_FIS_SZ = 256,
AHCI_CMD_TBL_HDR = 0x80,
AHCI_CMD_TBL_CDB = 0x40,
AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR + (AHCI_MAX_SG * 16),
AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_SZ +
AHCI_RX_FIS_SZ,
AHCI_IRQ_ON_SG = (1 << 31),
AHCI_CMD_ATAPI = (1 << 5),
AHCI_CMD_WRITE = (1 << 6),
RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
board_ahci = 0,
/* global controller registers */
HOST_CAP = 0x00, /* host capabilities */
HOST_CTL = 0x04, /* global host control */
HOST_IRQ_STAT = 0x08, /* interrupt status */
HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */
HOST_VERSION = 0x10, /* AHCI spec. version compliancy */
/* HOST_CTL bits */
HOST_RESET = (1 << 0), /* reset controller; self-clear */
HOST_IRQ_EN = (1 << 1), /* global IRQ enable */
HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
/* HOST_CAP bits */
HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
/* registers for each SATA port */
PORT_LST_ADDR = 0x00, /* command list DMA addr */
PORT_LST_ADDR_HI = 0x04, /* command list DMA addr hi */
PORT_FIS_ADDR = 0x08, /* FIS rx buf addr */
PORT_FIS_ADDR_HI = 0x0c, /* FIS rx buf addr hi */
PORT_IRQ_STAT = 0x10, /* interrupt status */
PORT_IRQ_MASK = 0x14, /* interrupt enable/disable mask */
PORT_CMD = 0x18, /* port command */
PORT_TFDATA = 0x20, /* taskfile data */
PORT_SIG = 0x24, /* device TF signature */
PORT_CMD_ISSUE = 0x38, /* command issue */
PORT_SCR = 0x28, /* SATA phy register block */
PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */
PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */
PORT_SCR_ERR = 0x30, /* SATA phy register: SError */
PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
/* PORT_IRQ_{STAT,MASK} bits */
PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
PORT_IRQ_TF_ERR = (1 << 30), /* task file error */
PORT_IRQ_HBUS_ERR = (1 << 29), /* host bus fatal error */
PORT_IRQ_HBUS_DATA_ERR = (1 << 28), /* host bus data error */
PORT_IRQ_IF_ERR = (1 << 27), /* interface fatal error */
PORT_IRQ_IF_NONFATAL = (1 << 26), /* interface non-fatal error */
PORT_IRQ_OVERFLOW = (1 << 24), /* xfer exhausted available S/G */
PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */
PORT_IRQ_DEV_ILCK = (1 << 7), /* device interlock */
PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */
PORT_IRQ_SG_DONE = (