/*
* sata_sil24.c - Driver for Silicon Image 3124/3132 SATA-2 controllers
*
* Copyright 2005 Tejun Heo
*
* Based on preview driver from Silicon Image.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2, or (at your option) any
* later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/dma-mapping.h>
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
#include <linux/libata.h>
#define DRV_NAME "sata_sil24"
#define DRV_VERSION "0.3"
/*
* Port request block (PRB) 32 bytes
*/
struct sil24_prb {
__le16 ctrl;
__le16 prot;
__le32 rx_cnt;
u8 fis[6 * 4];
};
/*
* Scatter gather entry (SGE) 16 bytes
*/
struct sil24_sge {
__le64 addr;
__le32 cnt;
__le32 flags;
};
/*
* Port multiplier
*/
struct sil24_port_multiplier {
__le32 diag;
__le32 sactive;
};
enum {
SIL24_HOST_BAR = 0,
SIL24_PORT_BAR = 2,
/*
* Global controller registers (128 bytes @ BAR0)
*/
/* 32 bit regs */
HOST_SLOT_STAT = 0x00, /* 32 bit slot stat * 4 */
HOST_CTRL = 0x40,
HOST_IRQ_STAT = 0x44,
HOST_PHY_CFG = 0x48,
HOST_BIST_CTRL = 0x50,
HOST_BIST_PTRN = 0x54,
HOST_BIST_STAT = 0x58,
HOST_MEM_BIST_STAT = 0x5c,
HOST_FLASH_CMD = 0x70,
/* 8 bit regs */
HOST_FLASH_DATA = 0x74,
HOST_TRANSITION_DETECT = 0x75,
HOST_GPIO_CTRL = 0x76,
HOST_I2C_ADDR = 0x78, /* 32 bit */
HOST_I2C_DATA = 0x7c,
HOST_I2C_XFER_CNT = 0x7e,
HOST_I2C_CTRL = 0x7f,
/* HOST_SLOT_STAT bits */
HOST_SSTAT_ATTN = (1 << 31),
/* HOST_CTRL bits */
HOST_CTRL_M66EN = (1 << 16), /* M66EN PCI bus signal */
HOST_CTRL_TRDY = (1 << 17), /* latched PCI TRDY */
HOST_CTRL_STOP = (1 << 18), /* latched PCI STOP */
HOST_CTRL_DEVSEL = (1 << 19), /* latched PCI DEVSEL */
HOST_CTRL_REQ64 = (1 << 20), /* latched PCI REQ64 */
HOST_CTRL_GLOBAL_RST = (1 << 31), /* global reset */
/*
* Port registers
* (8192 bytes @ +0x0000, +0x2000, +0x4000 and +0x6000 @ BAR2)
*/
PORT_REGS_SIZE = 0x2000,
PORT_LRAM = 0x0000, /* 31 LRAM slots and PMP regs */
PORT_LRAM_SLOT_SZ = 0x0080, /* 32 bytes PRB + 2 SGE, ACT... */
PORT_PMP = 0x0f80, /* 8 bytes PMP * 16 (128 bytes) */
PORT_PMP_STATUS = 0x0000, /* port device status offset */
PORT_PMP_QACTIVE = 0x0004, /* port device QActive offset */
PORT_PMP_SIZE = 0x0008, /* 8 bytes per PMP */
/* 32 bit regs */
PORT_CTRL_STAT = 0x1000, /* write: ctrl-set, read: stat */
PORT_CTRL_CLR = 0x1004, /* write: ctrl-clear */
PORT_IRQ_STAT = 0x1008, /* high: status, low: interrupt */
PORT_IRQ_ENABLE_SET = 0x1010, /* write: enable-set */
PORT_IRQ_ENABLE_CLR = 0x1014, /* write: enable-clear */
PORT_ACTIVATE_UPPER_ADDR= 0x101c,
PORT_EXEC_FIFO = 0x1020, /* command execution fifo */
PORT_CMD_ERR = 0x1024, /* command error number */
PORT_FIS_CFG = 0x1028,
PORT_FIFO_THRES = 0x102c,
/* 16 bit regs */
PORT_DECODE_ERR_CNT = 0x1040,
PORT_DECODE_ERR_THRESH = 0x1042,
PORT_CRC_ERR_CNT = 0x1044,
PORT_CRC_ERR_THRESH = 0x1046,
PORT_HSHK_ERR_CNT = 0x1048