path: root/drivers/ata/ahci.h

/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
 *  ahci.h - Common AHCI SATA definitions and declarations
 *
 *  Maintained by:  Tejun Heo <tj@kernel.org>
 *    		    Please ALWAYS copy linux-ide@vger.kernel.org
 *		    on emails.
 *
 *  Copyright 2004-2005 Red Hat, Inc.
 *
 * libata documentation is available via 'make {ps|pdf}docs',
 * as Documentation/driver-api/libata.rst
 *
 * AHCI hardware documentation:
 * http://www.intel.com/technology/serialata/pdf/rev1_0.pdf
 * http://www.intel.com/technology/serialata/pdf/rev1_1.pdf
 */

#ifndef _AHCI_H
#define _AHCI_H

#include <linux/pci.h>
#include <linux/clk.h>
#include <linux/libata.h>
#include <linux/phy/phy.h>
#include <linux/regulator/consumer.h>

/* Enclosure Management Control */
#define EM_CTRL_MSG_TYPE              0x000f0000

/* Enclosure Management LED Message Type */
#define EM_MSG_LED_HBA_PORT           0x0000000f
#define EM_MSG_LED_PMP_SLOT           0x0000ff00
#define EM_MSG_LED_VALUE              0xffff0000
#define EM_MSG_LED_VALUE_ACTIVITY     0x00070000
#define EM_MSG_LED_VALUE_OFF          0xfff80000
#define EM_MSG_LED_VALUE_ON           0x00010000

enum {
	AHCI_MAX_PORTS		= 32,
	AHCI_MAX_CLKS		= 5,
	AHCI_MAX_SG		= 168, /* hardware max is 64K */
	AHCI_DMA_BOUNDARY	= 0xffffffff,
	AHCI_MAX_CMDS		= 32,
	AHCI_CMD_SZ		= 32,
	AHCI_CMD_SLOT_SZ	= AHCI_MAX_CMDS * AHCI_CMD_SZ,
	AHCI_RX_FIS_SZ		= 256,
	AHCI_CMD_TBL_CDB	= 0x40,
	AHCI_CMD_TBL_HDR_SZ	= 0x80,
	AHCI_CMD_TBL_SZ		= AHCI_CMD_TBL_HDR_SZ + (AHCI_MAX_SG * 16),
	AHCI_CMD_TBL_AR_SZ	= AHCI_CMD_TBL_SZ * AHCI_MAX_CMDS,
	AHCI_PORT_PRIV_DMA_SZ	= AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ +
				  AHCI_RX_FIS_SZ,
	AHCI_PORT_PRIV_FBS_DMA_SZ	= AHCI_CMD_SLOT_SZ +
					  AHCI_CMD_TBL_AR_SZ +
					  (AHCI_RX_FIS_SZ * 16),
	AHCI_IRQ_ON_SG		= (1 << 31),
	AHCI_CMD_ATAPI		= (1 << 5),
	AHCI_CMD_WRITE		= (1 << 6),
	AHCI_CMD_PREFETCH	= (1 << 7),
	AHCI_CMD_RESET		= (1 << 8),
	AHCI_CMD_CLR_BUSY	= (1 << 10),

	RX_FIS_PIO_SETUP	= 0x20,	/* offset of PIO Setup FIS data */
	RX_FIS_D2H_REG		= 0x40,	/* offset of D2H Register FIS data */
	RX_FIS_SDB		= 0x58, /* offset of SDB FIS data */
	RX_FIS_UNK		= 0x60, /* offset of Unknown FIS data */

	/* global controller registers */
	HOST_CAP		= 0x00, /* host capabilities */
	HOST_CTL		= 0x04, /* global host control */
	HOST_IRQ_STAT		= 0x08, /* interrupt status */
	HOST_PORTS_IMPL		= 0x0c, /* bitmap of implemented ports */
	HOST_VERSION		= 0x10, /* AHCI spec. version compliancy */
	HOST_EM_LOC		= 0x1c, /* Enclosure Management location */
	HOST_EM_CTL		= 0x20, /* Enclosure Management Control */
	HOST_CAP2		= 0x24, /* host capabilities, extended */

	/* HOST_CTL bits */
	HOST_RESET		= (1 << 0),  /* reset controller; self-clear */
	HOST_IRQ_EN		= (1 << 1),  /* global IRQ enable */
	HOST_MRSM		= (1 << 2),  /* MSI Revert to Single Message */
	HOST_AHCI_EN		= (1 << 31), /* AHCI enabled */

	/* HOST_CAP bits */
	HOST_CAP_SXS		= (1 << 5),  /* Supports External SATA */
	HOST_CAP_EMS		= (1 << 6),  /* Enclosure Management support */
	HOST_CAP_CCC		= (1 << 7),  /* Command Completion Coalescing */
	HOST_CAP_PART		= (1 << 13), /* Partial state capable */
	HOST_CAP_SSC		= (1 << 14), /* Slumber state capable */
	HOST_CAP_PIO_MULTI	= (1 << 15), /* PIO multiple DRQ support */
	HOST_CAP_FBS		= (1 << 16), /* FIS-based switching support */
	HOST_CAP_PMP		= (1 << 17), /* Port Multiplier support */
	HOST_CAP_ONLY		= (1 << 18), /* Supports AHCI mode only */
	HOST_CAP_CLO		= (1 << 24), /* Command List Override support */
	HOST_CAP_LED		= (1 << 25), /* Supports activity LED */
	HOST_CAP_ALPM		= (1 << 26), /* Aggressive Link PM support */
	HOST_CAP_SSS		= (1 << 27), /* Staggered Spin-up */
	HOST_CAP_MPS		= (1 << 28), /* Mechanical presence switch */
	HOST_CAP_SNTF		= (1 << 29), /* SNotification register */
	HOST_CAP_NCQ		= (1 << 30), /* Native Command Queueing */
	HOST_CAP_64		= (1 << 31), /* PCI DAC (64-bit DMA) support */

	/* HOST_CAP2 bits */
	HOST_CAP2_BOH		= (1 << 0),  /* BIOS/OS handoff supported */
	HOST_CAP2_NVMHCI	= (1 << 1),  /* NVMHCI supported */
	HOST_CAP2_APST		= (1 << 2),  /* Automatic partial to slumber */
	HOST_CAP2_SDS		= (1 << 3),  /* Support device sleep */
	HOST_CAP2_SADM		= (1 << 4),  /* Support aggressive DevSlp */
	HOST_CAP2_DESO		= (1 << 5),  /* DevSlp from slumber only */

	/* registers for each SATA port */
	PORT_LST_ADDR		= 0x00, /* command list DMA addr */
	PORT_LST_ADDR_HI	= 0x04, /* command list DMA addr hi */
	PORT_FIS_ADDR		= 0x08, /* FIS rx buf addr */
	PORT_FIS_ADDR_HI	= 0x0c, /* FIS rx buf addr hi */
	PORT_IRQ_STAT		= 0x10, /* interrupt status */
	PORT_IRQ_MASK		= 0x14, /* interrupt enable/disable mask */
	PORT_CMD		= 0x18, /* port command */
	PORT_TFDATA		= 0x20,	/* taskfile data */
	PORT_SIG		= 0x24,	/* device TF signature */
	PORT_CMD_ISSUE		= 0x38, /* command issue */
	PORT_SCR_STAT		= 0x28, /* SATA phy register: SStatus */
	PORT_SCR_CTL		= 0x2c, /* SATA phy register: SControl */
	PORT_SCR_ERR		= 0x30, /* SATA phy register: SError */
	PORT_SCR_ACT		= 0x34, /* SATA phy register: SActive */
	PORT_SCR_NTF		= 0x3c, /* SATA phy register: SNotification */
	PORT_FBS		= 0x40, /* FIS-based Switching */
	PORT_DEVSLP		= 0x44, /* device sleep */

	/* PORT_IRQ_{STAT,MASK} bits */
	PORT_IRQ_COLD_PRES	= (1 << 31), /* cold presence detect */
	PORT_IRQ_TF_ERR		= (1 << 30), /* task file error */
	PORT_IRQ_HBUS_ERR	= (1 << 29), /* host bus fatal error */
	PORT_IRQ_HBUS_DATA_ERR	= (1 << 28), /* host bus data error */
	PORT_IRQ_IF_ERR		= (1 << 27), /* interface fatal error */
	PORT_IRQ_IF_NONFATAL	= (1 << 26), /* interface non-fatal error */
	PORT_IRQ_OVERFLOW	= (1 << 24), /* xfer exhausted available S/G */
	PORT_IRQ_BAD_PMP	= (1 << 23), /* incorrect port multiplier */

	PORT_IRQ_PHYRDY		= (1 << 22), /* PhyRdy changed */
	PORT_IRQ_DEV_ILCK	= (1 << 7), /* device interlock */
	PORT_IRQ_CONNECT	= (1 << 6), /* port connect change status */
	PORT_IRQ_SG_DONE	= (1 << 5), /* descriptor processed */
	PORT_IRQ_UNK_FIS	= (1 << 4), /* unknown FIS rx'd */
	PORT_IRQ_SDB_FIS	= (1 << 3), /* Set Device Bits FIS rx'd */
	PORT_IRQ_DMAS_FIS	= (1 << 2), /* DMA Setup FIS rx'd */
	PORT_IRQ_PIOS_FIS	= (1 << 1), /* PIO Setup FIS rx'd */
	PORT_IRQ_D2H_REG_FIS	= (1 << 0), /* D2H Register FIS rx'd */

	PORT_IRQ_FREEZE		= PORT_IRQ_HBUS_ERR |
				  PORT_IRQ_IF_ERR |
				  PORT_IRQ_CONNECT |
				  PORT_IRQ_PHYRDY |
				  PORT_IRQ_UNK_FIS |
				  PORT_IRQ_BAD_PMP,
	PORT_IRQ_ERROR		= PORT_IRQ_FREEZE |
				  PORT_IRQ_TF_ERR |
				  PORT_IRQ_HBUS_DATA_ERR,
	DEF_PORT_IRQ		= PORT_IRQ_ERROR | PORT_IRQ_SG_DONE |
				  PORT_IRQ_SDB_FIS | PORT_IRQ_DMAS_FIS |
				  PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,

	/* PORT_CMD bits */
	PORT_CMD_ASP		= (1 << 27), /* Aggressive Slumber/Partial */
	PORT_CMD_ALPE		= (1 << 26), /* Aggressive Link PM enable */
	PORT_CMD_ATAPI		= (1 << 24), /* Device is ATAPI */
	PORT_CMD_FBSCP		= (1 << 22), /* FBS Capable Port */
	PORT_CMD_ESP		= (1 << 21), /* External Sata Port */
	PORT_CMD_HPCP		= (1 << 18), /* HotPlug Capable Port */
	PORT_CMD_PMP		= (1 << 17), /* PMP attached */
	PORT_CMD_LIST_ON	= (1 << 15), /* cmd list DMA engine running */
	PORT_CMD_FIS_ON		= (1 << 14), /* FIS DMA engine running */
	PORT_CMD_FIS_RX		= (1 << 4), /* Enable FIS receive DMA engine */
	PORT_CMD_CLO		= (1 << 3), /* Command list override */
	PORT_CMD_POWER_ON	= (1 << 2), /* Power up device */
	PORT_CMD_SPIN_UP	= (1 << 1), /* Spin up device */
	PORT_CMD_START		= (1 << 0), /* Enable port DMA engine */

	PORT_CMD_ICC_MASK	= (0xf << 28), /* i/f ICC state mask */
	PORT_CMD_ICC_ACTIVE	= (0x1 << 28), /* Put i/f in active state */
	PORT_CMD_ICC_PARTIAL	= (0x2 << 28), /* Put i/f in partial state */
	PORT_CMD_ICC_SLUMBER	=