// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
*/
#include "msm8996.dtsi"
#include "pm8994.dtsi"
#include "pmi8994.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/sound/qcom,q6afe.h>
#include <dt-bindings/sound/qcom,q6asm.h>
/*
* GPIO name legend: proper name = the GPIO line is used as GPIO
* NC = not connected (pin out but not routed from the chip to
* anything the board)
* "[PER]" = pin is muxed for [peripheral] (not GPIO)
* LSEC = Low Speed External Connector
* P HSEC = Primary High Speed External Connector
* S HSEC = Secondary High Speed External Connector
* J14 = Camera Connector
* TP = Test Points
*
* Line names are taken from the schematic "DragonBoard 820c",
* drawing no: LM25-P2751-1
*
* For the lines routed to the external connectors the
* lines are named after the 96Boards CE Specification 1.0,
* Appendix "Expansion Connector Signal Description".
*
* When the 96Board naming of a line and the schematic name of
* the same line are in conflict, the 96Board specification
* takes precedence, which means that the external UART on the
* LSEC is named UART0 while the schematic and SoC names this
* UART3. This is only for the informational lines i.e. "[FOO]",
* the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
* ones actually used for GPIO.
*/
/ {
aliases {
serial0 = &blsp2_uart1;
serial1 = &blsp2_uart2;
serial2 = &blsp1_uart1;
i2c0 = &blsp1_i2c2;
i2c1 = &blsp2_i2c1;
i2c2 = &blsp2_i2c0;
spi0 = &blsp1_spi0;
spi1 = &blsp2_spi5;
};
chosen {
stdout-path = "serial0:115200n8";
};
clocks {
compatible = "simple-bus";
divclk4: divclk4 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "divclk4";
pinctrl-names = "default";
pinctrl-0 = <&divclk4_pin_a>;
};
div1_mclk: divclk1 {
compatible = "gpio-gate-clock";
pinctrl-0 = <&audio_mclk>;
pinctrl-names = "default";
clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
#clock-cells = <0>;
enable-gpios = <&pm8994_gpios 15 0>;
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
autorepeat;
pinctrl-names = "default";
pinctrl-0 = <&volume_up_gpio>;
button@0 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
};
};
usb2_id: usb2-id {
compatible = "linux,extcon-usb-gpio";
id-gpio = <&pmi8994_gpios 6 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb2_vbus_det_gpio>;
};
usb3_id: usb3-id {
compatible = "linux,extcon-usb-gpio";
id-gpio = <&pm8994_gpios 22 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb3_vbus_det_gpio>;
};
wlan_en: wlan-en-1-8v {
pinctrl-names = "default";
pinctrl-0 = <&wlan_en_gpios>;
compatible = "regulator-fixed";
regulator-name = "wlan-en-regulator";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&pm8994_gpios 8 0>;
/* WLAN card specific delay */
startup-delay-us = <70000>;
enable-active-high;
};
};
&blsp1_i2c2 {
/* On Low speed expansion */
label = "LS-I2C0";
status = "okay";
};
&blsp1_spi0 {
/* On Low speed expansion */
label = "LS-SPI0";
status = "okay";
};
&blsp1_uart1 {
label = "BT-UART";
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_uart1_default>;
pinctrl-1 = <&blsp1_uart1_sleep>;
bluetooth {
compatible = "qcom,qca6174-bt";
/* bt_disable_n gpio */
enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
clocks = <&divclk4>;
};
};
&blsp2_i2c0 {
/* On High speed expansion */
label = "HS-I2C2";
status = "okay";
};
&blsp2_i2c1 {
/* On Low speed expansion */
label = "LS-I2C1";
status = "okay";
};
&blsp2_spi5 {
/* On High speed expansion */
label = "HS-SPI1";
status = "okay";
};
&blsp2_uart1 {
label = "LS-UART1";
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_uart1_2pins_default>;
pinctrl-1 = <&blsp2_uart1_2pins_sleep>;
};
&blsp2_uart2 {
label = "LS-UART0";
status =