Age | Commit message (Collapse) | Author |
|
Since commit d73dfc6a4199e0e3 ("serial: 8250_pci: remove __devexit
usage") in v3.9, the 8250/16550 PCI serial driver no longer has any code
or data located in initmem, hence there is no need to annotate the
pci_serial_quirks structure with __refdata. Drop the annotation, to
avoid suppressing future section warnings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201211133907.2970460-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pm_runtime_enable will increase power disable depth.
Thus a pairing decrement is needed on the error handling
path to keep it balanced according to context.
Fixes: e32a83c70cf98 ("serial: 8250-mtk: modify mtk uart power and clock management")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201119141126.168850-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/8250/8250_port.c:349:14: warning: no previous prototype for ‘au_serial_in’ [-Wmissing-prototypes]
drivers/tty/serial/8250/8250_port.c:359:6: warning: no previous prototype for ‘au_serial_out’ [-Wmissing-prototypes]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Mike Hudson <Exoray@isys.ca>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112105857.2078977-3-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With commit 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable"),
below warning is seen with W=1 and CONFIG_SERIAL_8250_DMA is disabled:
drivers/tty/serial/8250/8250_omap.c:1199:42: warning: unused variable 'k3_soc_devices' [-Wunused-const-variable]
Fix this by moving the code using k3_soc_devices array to
omap_serial_fill_features_erratas() that handles other errata flags as
well.
Fixes: 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
k3_soc_devices array is missing a sentinel entry which may result in out
of bounds access as reported by kernel KASAN.
Fix this by adding a sentinel entry.
Fixes: 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the TTY/vt/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud
rates in both the new and the old termios setting are higher than
uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered.
Passing NULL as the old termios so uart_get_baud_rate() will use
uartclk / 16 - 1 as the new baud rate which will be replaced by the
original baud rate later by tty_termios_encode_baud_rate() in
mtk8250_set_termios().
Fixes: 551e553f0d4a ("serial: 8250_mtk: Fix high-speed baud rates clamping")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UARTs on TI SoCs prior to J7200 don't provide independent control over
RX FIFO not empty interrupt (RHR_IT) and RX timeout interrupt.
Starting with J7200 SoC, its possible to disable RHR_IT independent of
RX timeout interrupt using bit 2 of IER2 register. So disable RHR_IT
once RX DMA is started so as to avoid spurious interrupt being raised
when data is in the RX FIFO but is yet to be drained by DMA (a known
errata in older SoCs).
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201029051930.7097-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/8250/serial_cs.c: In function ‘multi_config’:
drivers/tty/serial/8250/serial_cs.c:562:7: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: "David A. Hinds" <dahinds@users.sourceforge.net>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-15-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It has been discovered that there is a potential deadlock between
the clock-change-notifier thread and the UART port suspending one:
CPU0 (suspend CPU/UART) CPU1 (update clock)
---- ----
lock(&port->mutex);
lock((work_completion)(&data->clk_work));
lock(&port->mutex);
lock((work_completion)(&data->clk_work));
*** DEADLOCK ***
The best way to fix this is to eliminate the CPU0
port->mutex/work-completion scenario. So we suggest to register and
unregister the clock-notifier during the DW APB UART port probe/remove
procedures, instead of doing that at the points of the port
startup/shutdown.
Link: https://lore.kernel.org/linux-serial/f1cd5c75-9cda-6896-a4e2-42c5bfc3f5c3@redhat.com
Fixes: cc816969d7b5 ("serial: 8250_dw: Fix common clocks usage race condition")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is erroneous to update the TTY port baud rate if it hasn't been
initialized yet, because in that case the TTY struct isn't set. So there
is no termios structure to get and re-calculate the baud if the current
baud can't be reached. Let's skip the baud rate update then until the port
is fully initialized.
Note the update UART clock method still sets the uartclk member with a new
ref clock value even if the port is turned off. The new UART ref clock
rate will be used later on the port starting up procedure.
Fixes: 868f3ee6e452 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It has been a mistake to add the MCR register RTS/DTS fields setting in
the generic method of the UART reference clock update. There is no point
in asserting these lines at that procedure. Just discard the
serial8250_out_MCR() mathod invocation from there then.
Fixes: 868f3ee6e452 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the port of the commit db1b5bc047b3 ("serial: 8250: Fix TX
interrupt handling condition") to the 8250_fsl irq handling logic.
Interrupt handler checked THRE bit (transmitter holding register
empty) in LSR to detect if TX fifo is empty.
In case when there is only receive interrupts the TX handling
got called because THRE bit in LSR is set when there is no
transmission (FIFO empty). TX handling caused TX stop, which in
RS-485 half-duplex mode actually resets receiver FIFO. This is not
desired during reception because of possible data loss.
The fix is to check if THRI is set in IER in addition of the TX
fifo status. THRI in IER is set when TX is started and cleared
when TX is stopped.
This ensures that TX handling is only called when there is really
transmission on going and an interrupt for THRE and not when there
are only RX interrupts.
Signed-off-by: Andrij Abyzov <aabyzov@slb.com>
Link: https://lore.kernel.org/r/20200928144127.87156-1-aabyzov@slb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here and this resolves a merge issue in
the 8250 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These serial ports are exposed by the OOB-management-engine on
RealManage-enabled network cards (e.g. AMD DASH enabled systems using
Realtek cards).
Because these have 3 BARs, they fail the "num_iomem <= 1" check in
serial_pci_guess_board.
I've manually checked the two IOMEM regions and BAR 2 doesn't seem to
respond to reads, but BAR 4 seems to be an MMIO version of the IO ports
(untested).
With this change, the ports are detected:
0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A
0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A
lspci output:
02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550])
Subsystem: 17aa:5082
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 82
IOMMU group: 11
Region 0: I/O ports at 2200 [size=256]
Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
Not readable
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [170 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Capabilities: [178 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=10us
02:00.2 0700: 10ec:816b (rev 0e)
[...same...]
Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To use mmio32, we also need to set regshift.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Link: https://lore.kernel.org/r/20200915054825.3289105-2-hsinyi@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is not used since commit 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200909135103.17768-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds support for ACPI enumerated FSL 16550 UARTs.
For supporting ACPI, I added a wrapper so that this driver
can be used if firmware has exposed the HID "NXP0018" in
DSDT table.
This will be built as object file if config "SERIAL_8250_FSL"
is enabled which depends on config "SERIAL_8250_CONSOLE".
Signed-off-by: kuldip dwivedi <kuldip.dwivedi@puresoftware.com>
Link: https://lore.kernel.org/r/20200903113402.12371-1-kuldip.dwivedi@puresoftware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20200901153100.18827-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add PCI id for WCH384_8S 8 port PCI-E serial card.
because this card has so many ports, you may have
to check these two options before use it:
CONFIG_SERIAL_8250_RUNTIME_UARTS
CONFIG_SERIAL_8250_NR_UARTS
Signed-off-by: Du Huanpeng <u74147@gmail.com>
Link: https://lore.kernel.org/r/1598060848-27807-1-git-send-email-u74147@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small TTY/Serial/vt fixes for 5.9-rc3
Included in here are:
- qcom serial fixes
- vt ioctl and core bugfixes
- pl011 serial driver fixes
- 8250 serial driver fixes
- other misc serial driver fixes
and for good measure:
- fbcon fix for syzbot found problem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: imx: add dependence and build for earlycon
serial: samsung: Removes the IRQ not found warning
serial: 8250: change lock order in serial8250_do_startup()
serial: stm32: avoid kernel warning on absence of optional IRQ
serial: pl011: Fix oops on -EPROBE_DEFER
serial: pl011: Don't leak amba_ports entry on driver register error
serial: 8250_exar: Fix number of ports for Commtech PCIe cards
tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setup
serial: qcom_geni_serial: Fix recent kdb hang
vt_ioctl: change VT_RESIZEX ioctl to check for error return from vc_resize()
fbcon: prevent user font height or width change from causing potential out-of-bounds access
vt: defer kfree() of vc_screenbuf in vc_do_resize()
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
We have a number of "uart.port->desc.lock vs desc.lock->uart.port"
lockdep reports coming from 8250 driver; this causes a bit of trouble
to people, so let's fix it.
The problem is reverse lock order in two different call paths:
chain #1:
serial8250_do_startup()
spin_lock_irqsave(&port->lock);
disable_irq_nosync(port->irq);
raw_spin_lock_irqsave(&desc->lock)
chain #2:
__report_bad_irq()
raw_spin_lock_irqsave(&desc->lock)
for_each_action_of_desc()
printk()
spin_lock_irqsave(&port->lock);
Fix this by changing the order of locks in serial8250_do_startup():
do disable_irq_nosync() first, which grabs desc->lock, and grab
uart->port after that, so that chain #1 and chain #2 have same lock
order.
Full lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.4.39 #55 Not tainted
======================================================
swapper/0/0 is trying to acquire lock:
ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57
but task is already holding lock:
ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&irq_desc_lock_class){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
__irq_get_desc_lock+0x65/0x89
__disable_irq_nosync+0x3b/0x93
serial8250_do_startup+0x451/0x75c
uart_startup+0x1b4/0x2ff
uart_port_activate+0x73/0xa0
tty_port_open+0xae/0x10a
uart_open+0x1b/0x26
tty_open+0x24d/0x3a0
chrdev_open+0xd5/0x1cc
do_dentry_open+0x299/0x3c8
path_openat+0x434/0x1100
do_filp_open+0x9b/0x10a
do_sys_open+0x15f/0x3d7
kernel_init_freeable+0x157/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #1 (&port_lock_key){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
serial8250_console_write+0xa7/0x2a0
console_unlock+0x3b7/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
register_console+0x336/0x3a4
uart_add_one_port+0x51b/0x5be
serial8250_register_8250_port+0x454/0x55e
dw8250_probe+0x4dc/0x5b9
platform_drv_probe+0x67/0x8b
really_probe+0x14a/0x422
driver_probe_device+0x66/0x130
device_driver_attach+0x42/0x5b
__driver_attach+0xca/0x139
bus_for_each_dev+0x97/0xc9
bus_add_driver+0x12b/0x228
driver_register+0x64/0xed
do_one_initcall+0x20c/0x4a6
do_initcall_level+0xb5/0xc5
do_basic_setup+0x4c/0x58
kernel_init_freeable+0x13f/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #0 (console_owner){-...}:
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
console_lock_spinning_enable+0x51/0x57
console_unlock+0x25d/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
ret_from_intr+0x0/0x1d
cpuidle_enter_state+0x12f/0x1fd
cpuidle_enter+0x2e/0x3d
do_idle+0x1ce/0x2ce
cpu_startup_entry+0x1d/0x1f
start_kernel+0x406/0x46a
secondary_startup_64+0xa4/0xb0
other info that might help us debug this:
Chain exists of:
console_owner --> &port_lock_key --> &irq_desc_lock_class
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&irq_desc_lock_class);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
lock(console_owner);
*** DEADLOCK ***
2 locks held by swapper/0/0:
#0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
#1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55
Hardware name: XXXXXX
Call Trace:
<IRQ>
dump_stack+0xbf/0x133
? print_circular_bug+0xd6/0xe9
check_noncircular+0x1b9/0x1c3
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
? console_lock_spinning_enable+0x31/0x57
console_lock_spinning_enable+0x51/0x57
? console_lock_spinning_enable+0x31/0x57
console_unlock+0x25d/0x528
? console_trylock+0x18/0x4e
vprintk_emit+0x111/0x17f
? lock_acquire+0x203/0x258
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
common_interrupt+0xf/0xf
</IRQ>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Raul Rangel <rrangel@google.com>
BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800
Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:
nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 679193b7baf8d88e41cbeb397ca17f797654947d.
It appears that in QEmu the lock has been initialised differently
(it wasn't obvious on real hardware during testing). Let's
revert the change until the better approach will be developed.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200802111612.36189-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the serial core handles spin lock initialisation,
let the driver rely on it.
Depends-on: f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731123733.22754-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The race condition may happen if the UART reference clock is shared with
some other device (on Baikal-T1 SoC it's another DW UART port). In this
case if that device changes the clock rate while serial console is using
it the DW 8250 UART port might not only end up with an invalid uartclk
value saved, but may also experience a distorted output data since
baud-clock could have been changed. In order to fix this lets at least
try to adjust the 8250 port setting like UART clock rate in case if the
reference clock rate change is discovered. The driver will call the new
method to update 8250 UART port clock rate settings. It's done by means of
the clock event notifier registered at the port startup and unregistered
in the shutdown callback method.
Note 1. In order to avoid deadlocks we had to execute the UART port update
method in a dedicated deferred work. This is due to (in my opinion
redundant) the clock update implemented in the dw8250_set_termios()
method.
Note 2. Before the ref clock is manually changed by the custom
set_termios() function we swap the port uartclk value with new rate
adjusted to be suitable for the requested baud. It is necessary in
order to effectively disable a functionality of the ref clock events
handler for the current UART port, since uartclk update will be done
a bit further in the generic serial8250_do_set_termios() function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Indeed according to the clk API if clk_round_rate() has successfully
accepted a rate, then in order setup the clock with value returned by the
clk_round_rate() the clk_set_rate() method must be called with the
original rate value.
Suggested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Really instead of twice checking the clk_round_rate() return value
we could do it once, and if it isn't error the clock rate can be changed.
By doing so we decrease a number of ret-value tests and remove a weird
goto-based construction implemented in the dw8250_set_termios() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some platforms can be designed in a way so the UART port reference clock
might be asynchronously changed at some point. In Baikal-T1 SoC this may
happen due to the reference clock being shared between two UART ports, on
the Allwinner SoC the reference clock is derived from the CPU clock, so
any CPU frequency change should get to be known/reflected by/in the UART
controller as well. But it's not enough to just update the
uart_port->uartclk field of the corresponding UART port, the 8250
controller reference clock divisor should be altered so to preserve
current baud rate setting. All of these things is done in a coherent
way by calling the serial8250_update_uartclk() method provided in this
patch. Though note that it isn't supposed to be called from within the
UART port callbacks because the locks using to the protect the UART port
data are already taken in there.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
we need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1d. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1d
With GPIOs preconfigured as per commit 7dea8165f1d all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1d6 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064ec3 ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com
Fixes: 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port")
Reported-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: stable <stable@vger.kernel.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I got null-ptr-deref in serial8250_start_tx():
[ 78.114630] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[ 78.123778] Mem abort info:
[ 78.126560] ESR = 0x86000007
[ 78.129603] EC = 0x21: IABT (current EL), IL = 32 bits
[ 78.134891] SET = 0, FnV = 0
[ 78.137933] EA = 0, S1PTW = 0
[ 78.141064] user pgtable: 64k pages, 48-bit VAs, pgdp=00000027d41a8600
[ 78.147562] [0000000000000000] pgd=00000027893f0003, p4d=00000027893f0003, pud=00000027893f0003, pmd=00000027c9a20003, pte=0000000000000000
[ 78.160029] Internal error: Oops: 86000007 [#1] SMP
[ 78.164886] Modules linked in: sunrpc vfat fat aes_ce_blk crypto_simd cryptd aes_ce_cipher crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce ses enclosure sg sbsa_gwdt ipmi_ssif spi_dw_mmio sch_fq_codel vhost_net tun vhost vhost_iotlb tap ip_tables ext4 mbcache jbd2 ahci hisi_sas_v3_hw libahci hisi_sas_main libsas hns3 scsi_transport_sas hclge libata megaraid_sas ipmi_si hnae3 ipmi_devintf ipmi_msghandler br_netfilter bridge stp llc nvme nvme_core xt_sctp sctp libcrc32c dm_mod nbd
[ 78.207383] CPU: 11 PID: 23258 Comm: null-ptr Not tainted 5.8.0-rc6+ #48
[ 78.214056] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B210.01 03/12/2020
[ 78.222888] pstate: 80400089 (Nzcv daIf +PAN -UAO BTYPE=--)
[ 78.228435] pc : 0x0
[ 78.230618] lr : serial8250_start_tx+0x160/0x260
[ 78.235215] sp : ffff800062eefb80
[ 78.238517] x29: ffff800062eefb80 x28: 0000000000000fff
[ 78.243807] x27: ffff800062eefd80 x26: ffff202fd83b3000
[ 78.249098] x25: ffff800062eefd80 x24: ffff202fd83b3000
[ 78.254388] x23: ffff002fc5e50be8 x22: 0000000000000002
[ 78.259679] x21: 0000000000000001 x20: 0000000000000000
[ 78.264969] x19: ffffa688827eecc8 x18: 0000000000000000
[ 78.270259] x17: 0000000000000000 x16: 0000000000000000
[ 78.275550] x15: ffffa68881bc67a8 x14: 00000000000002e6
[ 78.280841] x13: ffffa68881bc67a8 x12: 000000000000c539
[ 78.286131] x11: d37a6f4de9bd37a7 x10: ffffa68881cccff0
[ 78.291421] x9 : ffffa68881bc6000 x8 : ffffa688819daa88
[ 78.296711] x7 : ffffa688822a0f20 x6 : ffffa688819e0000
[ 78.302002] x5 : ffff800062eef9d0 x4 : ffffa68881e707a8
[ 78.307292] x3 : 0000000000000000 x2 : 0000000000000002
[ 78.312582] x1 : 0000000000000001 x0 : ffffa688827eecc8
[ 78.317873] Call trace:
[ 78.320312] 0x0
[ 78.322147] __uart_start.isra.9+0x64/0x78
[ 78.326229] uart_start+0xb8/0x1c8
[ 78.329620] uart_flush_chars+0x24/0x30
[ 78.333442] n_tty_receive_buf_common+0x7b0/0xc30
[ 78.338128] n_tty_receive_buf+0x44/0x2c8
[ 78.342122] tty_ioctl+0x348/0x11f8
[ 78.345599] ksys_ioctl+0xd8/0xf8
[ 78.348903] __arm64_sys_ioctl+0x2c/0xc8
[ 78.352812] el0_svc_common.constprop.2+0x88/0x1b0
[ 78.357583] do_el0_svc+0x44/0xd0
[ 78.360887] el0_sync_handler+0x14c/0x1d0
[ 78.364880] el0_sync+0x140/0x180
[ 78.368185] Code: bad PC value
SERIAL_PORT_DFNS is not defined on each arch, if it's not defined,
serial8250_set_defaults() won't be called in serial8250_isa_init_ports(),
so the p->serial_in pointer won't be initialized, and it leads a null-ptr-deref.
Fix this problem by calling serial8250_set_defaults() after init uart port.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200721143852.4058352-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200718123840.19957-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200618122952.88265-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618123320.88612-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618122744.88204-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618122024.87170-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618095144.73852-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
get_num_ports returns -ENODEV, and the result is stored in int, so it
should not be unsigned. Zero ports does not seem to make sense, so
make that check consistent.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Link: https://lore.kernel.org/r/20200606151146.GA10940@amd
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop the recently added gpio include from the serial-core header in
favour of a forward declaration and instead include the gpio header only
where needed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200610155121.14014-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
All of these have been in linux-next with no issues for a while"
* tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (67 commits)
tty: serial: qcom_geni_serial: Add 51.2MHz frequency support
tty: serial: imx: clear Ageing Timer Interrupt in handler
serial: 8250_fintek: Add F81966 Support
sc16is7xx: Add flag to activate IrDA mode
dt-bindings: sc16is7xx: Add flag to activate IrDA mode
serial: 8250: Support rs485 bus termination GPIO
serial: 8520_port: Fix function param documentation
dt-bindings: serial: Add binding for rs485 bus termination GPIO
vt: keyboard: avoid signed integer overflow in k_ascii
serial: 8250: Enable 16550A variants by default on non-x86
tty: hvc_console, fix crashes on parallel open/close
serial: imx: Initialize lock for non-registered console
sc16is7xx: Read the LSR register for basic device presence check
sc16is7xx: Allow sharing the IRQ line
sc16is7xx: Use threaded IRQ
sc16is7xx: Always use falling edge IRQ
tty: n_gsm: Fix bogus i++ in gsm_data_kick
tty: n_gsm: Remove unnecessary test in gsm_print_packet()
serial: stm32: add no_console_suspend support
tty: serial: fsl_lpuart: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Program MPS for RCiEP devices (Ashok Raj)
- Fix pci_register_host_bridge() device_register() error handling
(Rob Herring)
- Fix pci_host_bridge struct device release/free handling (Rob
Herring)
Resource management:
- Allow resizing BARs for devices on root bus (Ard Biesheuvel)
Power management:
- Reduce Thunderbolt resume time by working around devices that don't
support DLL Link Active reporting (Mika Westerberg)
- Work around a Pericom USB controller OHCI/EHCI PME# defect
(Kai-Heng Feng)
Virtualization:
- Add ACS quirk for Intel Root Complex Integrated Endpoints (Ashok
Raj)
- Avoid FLR for AMD Starship USB 3.0 (Kevin Buettner)
- Avoid FLR for AMD Matisse HD Audio & USB 3.0 (Marcos Scriven)
Error handling:
- Use only _OSC (no |