summaryrefslogtreecommitdiffstats
path: root/drivers/rtc
AgeCommit message (Collapse)Author
2020-12-11ntp: Make the RTC sync offset less obscureThomas Gleixner
The current RTC set_offset_nsec value is not really intuitive to understand. tsched twrite(t2.tv_sec - 1) t2 (seconds increment) The offset is calculated from twrite based on the assumption that t2 - twrite == 1s. That means for the MC146818 RTC the offset needs to be negative so that the write happens 500ms before t2. It's easier to understand when the whole calculation is based on t2. That avoids negative offsets and the meaning is obvious: t2 - twrite: The time defined by the chip when seconds increment after the write. twrite - tsched: The time for the transport to the point where the chip is updated. ==> set_offset_nsec = t2 - tsched ttransport = twrite - tsched tRTCinc = t2 - twrite ==> set_offset_nsec = ttransport + tRTCinc tRTCinc is a chip property and can be obtained from the data sheet. ttransport depends on how the RTC is connected. It is close to 0 for directly accessible RTCs. For RTCs behind a slow bus, e.g. i2c, it's the time required to send the update over the bus. This can be estimated or even calibrated, but that's a different problem. Adjust the implementation and update comments accordingly. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201206220542.263204937@linutronix.de
2020-12-11ntp, rtc: Move rtc_set_ntp_time() to ntp codeThomas Gleixner
rtc_set_ntp_time() is not really RTC functionality as the code is just a user of RTC. Move it into the NTP code which allows further cleanups. Requested-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201206220542.166871172@linutronix.de
2020-12-11rtc: core: Make the sync offset default more realisticThomas Gleixner
The offset which is used to steer the start of an RTC synchronization update via rtc_set_ntp_time() is huge. The math behind this is: tsched twrite(t2.tv_sec - 1) t2 (seconds increment) twrite - tsched is the transport time for the write to hit the device. t2 - twrite depends on the chip and is for most chips one second. The rtc_set_ntp_time() calculation of tsched is: tsched = t2 - 1sec - (t2 - twrite) The default for the sync offset is 500ms which means that twrite - tsched is 500ms assumed that t2 - twrite is one second. This is 0.5 seconds off for RTCs which are directly accessible by IO writes and probably for the majority of i2C/SPI based RTC off by an order of magnitude. Set it to 5ms which should bring it closer to reality. The default can be adjusted by drivers (rtc_cmos does so) and could be adjusted further by a calibration method which is an orthogonal problem. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201206220541.960333166@linutronix.de
2020-12-11rtc: cmos: Make rtc_cmos sync offset correctThomas Gleixner
The offset for rtc_cmos must be -500ms to work correctly with the current implementation of rtc_set_ntp_time() due to the following: tsched twrite(t2.tv_sec - 1) t2 (seconds increment) twrite - tsched is the transport time for the write to hit the device, which is negligible for this chip because it's accessed directly. t2 - twrite = 500ms according to the datasheet. But rtc_set_ntp_time() calculation of tsched is: tsched = t2 - 1sec - (t2 - twrite) The default for the sync offset is 500ms which means that the write happens at t2 - 1.5 seconds which is obviously off by a second for this device. Make the offset -500ms so it works correct. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201206220541.830517160@linutronix.de
2020-12-11rtc: mc146818: Reduce spinlock section in mc146818_set_time()Thomas Gleixner
No need to hold the lock and disable interrupts for doing math. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201206220541.709243630@linutronix.de
2020-12-11rtc: mc146818: Prevent reading garbageThomas Gleixner
The MC146818 driver is prone to read garbage from the RTC. There are several issues all related to the update cycle of the MC146818. The chip increments seconds obviously once per second and indicates that by a bit in a register. The bit goes high 244us before the actual update starts. During the update the readout of the time values is undefined. The code just checks whether the update in progress bit (UIP) is set before reading the clock. If it's set it waits arbitrary 20ms before retrying, which is ample because the maximum update time is ~2ms. But this check does not guarantee that the UIP bit goes high and the actual update happens during the readout. So the following can happen 0.997 UIP = False -> Interrupt/NMI/preemption 0.998 UIP -> True 0.999 Readout <- Undefined To prevent this rework the code so it checks UIP before and after the readout and if set after the readout try again. But that's not enough to cover the following: 0.997 UIP = False Readout seconds -> NMI (or vCPU scheduled out) 0.998 UIP -> True update completes UIP -> False 1.000 Readout minutes,.... UIP check succeeds That can make the readout wrong up to 59 seconds. To prevent this, read the seconds value before the first UIP check, validate it after checking UIP and after reading out the rest. It's amazing that the original i386 code had this actually correct and the generic implementation of the MC146818 driver got it wrong in 2002 and it stayed that way until today. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201206220541.594826678@linutronix.de
2020-10-21Merge tag 'rtc-5.10' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux Pull RTC updates from Alexandre Belloni: "A new driver this cycle is making the bulk of the changes and the rx8010 driver has been rework to use the modern APIs. Summary: Subsystem: - new generic DT properties: aux-voltage-chargeable, trickle-voltage-millivolt New driver: - Microcrystal RV-3032 Drivers: - ds1307: use aux-voltage-chargeable - r9701, rx8010: modernization of the driver - rv3028: fix clock output, trickle resistor values, RAM configuration registers" * tag 'rtc-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits) rtc: r9701: set range rtc: r9701: convert to devm_rtc_allocate_device rtc: r9701: stop setting RWKCNT rtc: r9701: remove useless memset rtc: r9701: stop setting a default time rtc: r9701: remove leftover comment rtc: rv3032: Add a driver for Microcrystal RV-3032 dt-bindings: rtc: rv3032: add RV-3032 bindings dt-bindings: rtc: add trickle-voltage-millivolt rtc: rv3028: ensure ram configuration registers are saved rtc: rv3028: factorize EERD bit handling rtc: rv3028: fix trickle resistor values rtc: rv3028: fix clock output support rtc: mt6397: Remove unused member dev rtc: rv8803: simplify the return expression of rv8803_nvram_write rtc: meson: simplify the return expression of meson_vrtc_probe rtc: rx8010: rename rx8010_init_client() to rx8010_init() rtc: ds1307: enable rx8130's backup battery, make it chargeable optionally rtc: ds1307: consider aux-voltage-chargeable rtc: ds1307: store previous charge default per chip ...
2020-10-19rtc: r9701: set rangeAlexandre Belloni
Set range and remove the set_time check. This is a classic BCD RTC. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201015191135.471249-6-alexandre.belloni@bootlin.com
2020-10-19rtc: r9701: convert to devm_rtc_allocate_deviceAlexandre Belloni
This allows further improvement of the driver. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201015191135.471249-5-alexandre.belloni@bootlin.com
2020-10-19rtc: r9701: stop setting RWKCNTAlexandre Belloni
tm_wday is never checked for validity and it is not read back in r9701_get_datetime. Avoid setting it to stop tripping static checkers: drivers/rtc/rtc-r9701.c:109 r9701_set_datetime() error: undefined (user controlled) shift '1 << dt->tm_wday' Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201015191135.471249-4-alexandre.belloni@bootlin.com
2020-10-19rtc: r9701: remove useless memsetAlexandre Belloni
The RTC core already sets to zero the struct rtc_tie it passes to the driver, avoid doing it a second time. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201015191135.471249-3-alexandre.belloni@bootlin.com
2020-10-19rtc: r9701: stop setting a default timeAlexandre Belloni
It doesn't make sense to set the RTC to a default value at probe time. Let the core handle invalid date and time. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201015191135.471249-2-alexandre.belloni@bootlin.com
2020-10-19rtc: r9701: remove leftover commentAlexandre Belloni
Commit 22652ba72453 ("rtc: stop validating rtc_time in .read_time") removed the code but not the associated comment. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201015191135.471249-1-alexandre.belloni@bootlin.com
2020-10-19rtc: rv3032: Add a driver for Microcrystal RV-3032Alexandre Belloni
New driver for the Microcrystal RV-3032, including support for: - Date/time - Alarms - Low voltage detection - Trickle charge - Trimming - Clkout - RAM - EEPROM - Temperature sensor Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201013144110.1942218-3-alexandre.belloni@bootlin.com
2020-10-15rtc: rv3028: ensure ram configuration registers are savedAlexandre Belloni
If RV3028_CTRL1_EERD is not set (this is the default), the RTC will refresh the RAM configuration registers from the EEPROM at midnight. It is necessary to save the RAM registers back to EEPROM after modifying them. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201009153101.721149-4-alexandre.belloni@bootlin.com
2020-10-15rtc: rv3028: factorize EERD bit handlingAlexandre Belloni
Both rv3028_eeprom_write and rv3028_eeprom_read enable EERD before sending commands to the EEPROM and restore it afterwards. Factorize this code. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201009153101.721149-3-alexandre.belloni@bootlin.com
2020-10-15rtc: rv3028: fix trickle resistor valuesAlexandre Belloni
Version 1.0 of the application manual had the wrong resistor values. Fix them according to version 1.1 Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201009153101.721149-2-alexandre.belloni@bootlin.com
2020-10-15rtc: rv3028: fix clock output supportAlexandre Belloni
rv3028_clkout_set_rate unconditionally sets RV3028_CLKOUT_CLKOE but clk_set_rate may be called with the clock disabled. Ensure the clock is kept disabled if it was not yet enabled. Also, the actual rate was overwritten when enabling the clock, properly write to the register only once. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201009153101.721149-1-alexandre.belloni@bootlin.com
2020-10-15rtc: mt6397: Remove unused member devFei Shao
Removing the struct member "dev" in mt6397 RTC driver because it's not initialized and the only usage is for one debugging message. Also fixed a typo in the error message. Signed-off-by: Fei Shao <fshao@chromium.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20201008093414.1911699-1-fshao@chromium.org
2020-09-29rtc: rv8803: simplify the return expression of rv8803_nvram_writeLiu Shixin
Simplify the return expression. Signed-off-by: Liu Shixin <liushixin2@huawei.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200921082449.2591981-1-liushixin2@huawei.com
2020-09-29rtc: meson: simplify the return expression of meson_vrtc_probeLiu Shixin
Simplify the return expression. Signed-off-by: Liu Shixin <liushixin2@huawei.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Kevin Hilman <khilman@baylibre.com> Link: https://lore.kernel.org/r/20200919100856.1639319-1-liushixin2@huawei.com
2020-09-29rtc: rx8010: rename rx8010_init_client() to rx8010_init()Bartosz Golaszewski
Since the switch to using regmap this function no longer takes the I2C client struct as argument nor do we even interact with the client anywhere other than when creating the regmap. Rename it to a less misleading name: "rx8010_init()". Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200917114656.9036-1-brgl@bgdev.pl
2020-09-24rtc: ds1307: enable rx8130's backup battery, make it chargeable optionallyBastian Krause
The ds1307 charger infrastructure now allows to add a rx8130 charger setup that.. - does not depend on trickle-resistor-ohms - does not use DS13XX_TRICKLE_CHARGER_MAGIC trickle-charge select (TCS) bits - keeps previous no-charge behavior for device trees without aux-voltage-chargeable Make that happen. Signed-off-by: Bastian Krause <bst@pengutronix.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200917183246.19446-9-bst@pengutronix.de
2020-09-24rtc: ds1307: consider aux-voltage-chargeableBastian Krause
Prefer aux-voltage-chargeable over trickle-diode-disable and set diode accordingly. This is then passed to the chip's appropriate charge setup function. Signed-off-by: Bastian Krause <bst@pengutronix.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200917183246.19446-8-bst@pengutronix.de
2020-09-24rtc: ds1307: store previous charge default per chipBastian Krause
Some RTC's batteries and supercaps were charged by default until now. In contrast other RTCs allow charging but the driver did not configure them to do so until now. These must not be charged by default to stay backwards compatible. In order to do that, store the charge default per chip. Signed-off-by: Bastian Krause <bst@pengutronix.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200917183246.19446-7-bst@pengutronix.de
2020-09-24rtc: ds1307: introduce requires_trickle_resistor per chipBastian Krause
Make trickle-resistor-ohms optional for charging setups that do not require specifying ROUT bits (specifying the resistor value between Vcc and Vbackup). In order to allow specifying that, introduce requires_trickle_resistor per chip. Signed-off-by: Bastian Krause <bst@pengutronix.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200917183246.19446-6-bst@pengutronix.de
2020-09-24rtc: ds1307: apply DS13XX_TRICKLE_CHARGER_MAGIC only conditionallyBastian Krause
DS13XX_TRICKLE_CHARGER_MAGIC sets the trickle-charge select (TCS) bits (7..4). The datasheet of Maxim Integrated's DS1339 [1] for instance reads: "To prevent accidental enabling, only a pattern on 1010 enables the trickle charger. All other patterns disable the trickle charger." Since not all RTCs connected to a backup battery or supercap use these bits DS13XX_TRICKLE_CHARGER_MAGIC should not get applied for all charger setups unconditionally. Epson's RX8130 is such an example: Instead of TCS bits "SMPTSEL1", "SMPTSEL0", "CHGEN" and "INIEN" are expected as bit 7..4. DS1339 and DS1340 are currently the only RTCs in the ds1307 driver that apply DS13XX_TRICKLE_CHARGER_MAGIC to their setup register value. So apply DS13XX_TRICKLE_CHARGER_MAGIC in do_trickle_setup_ds1339() which is used by both RTCs. [1] https://datasheets.maximintegrated.com/en/ds/DS1339-DS1339U.pdf [2] https://support.epson.biz/td/api/doc_check.php?dl=app_RX8130CE Signed-off-by: Bastian Krause <bst@pengutronix.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200917183246.19446-5-bst@pengutronix.de
2020-09-15rtc: pcf2127: fix a bug when not specify interrupts propertyBiwen Li
Fix a bug when not specify interrupts property in dts as follows, rtc-pcf2127-i2c 1-0051: failed to request alarm irq rtc-pcf2127-i2c: probe of 1-0051 failed with error -22 Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200915073213.12779-1-biwen.li@oss.nxp.com
2020-09-15rtc: ds1685: Fix bank switching to avoid endless loopThomas Bogendoerfer
ds1685_rtc_begin_data_access() tried to access an extended register before enabling access to it by switching to bank 1. Depending on content in NVRAM this could lead to an endless loop. While at it fix also switch back to bank 0 in ds1685_rtc_end_data_access(). Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Joshua Kinard <kumba@gentoo.org> Link: https://lore.kernel.org/r/20200910084124.138560-1-tsbogend@alpha.franken.de
2020-09-15rtc: st-lpc: Constify st_rtc_opsRikard Falkeborn
The only usage of st_rtc_ops is to assign its address to the ops field in the rtc_device struct. which is a const pointer. Make it const to allow the compiler to put it in read-only memory. Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200913122644.35515-1-rikard.falkeborn@gmail.com
2020-09-15rtc: rx8010: use range checking provided by core RTC codeBartosz Golaszewski
We don't need to check the time range manually in set_time(), we can use range_min and range_max exposed by struct rtc_device. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-15-brgl@bgdev.pl
2020-09-15rtc: rx8010: convert to using regmapBartosz Golaszewski
This driver requires SMBUS to work. We can relax this requirement if we switch to using i2c regmap and let the regmap sub-system figure out how to talk to the bus. This also has the advantage of shrinking the code for register updates. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-14-brgl@bgdev.pl
2020-09-15rtc: rx8010: switch to using the preferred i2c APIBartosz Golaszewski
We should generally use probe_new instead of probe when registering i2c drivers. Convert rx8010 to using it. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-13-brgl@bgdev.pl
2020-09-15rtc: rx8010: switch to using the preferred RTC APIBartosz Golaszewski
Use devm_rtc_allocate_device() + rtc_register_device() instead of the deprecated devm_rtc_device_register(). Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-12-brgl@bgdev.pl
2020-09-15rtc: rx8010: prefer sizeof(*val) over sizeof(struct type_of_val)Bartosz Golaszewski
Using the size of the variable is preferred over using the size of its type when allocating memory. Convert the call to devm_kzalloc() in probe(). Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-11-brgl@bgdev.pl
2020-09-15rtc: rx8010: use a helper variable for client->dev in probe()Bartosz Golaszewski
Simple 'dev' looks better then repeated &client->dev and has the added benefit of avoiding unnecessary line breaks. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-10-brgl@bgdev.pl
2020-09-15rtc: rx8010: drop unnecessary initializationBartosz Golaszewski
The 'err' local variable in rx8010_init_client() doesn't need to be initialized. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-9-brgl@bgdev.pl
2020-09-15rtc: rx8010: don't use magic values for time buffer lengthBartosz Golaszewski
The time buffer len is used directly in this driver. For readability it's better to define it as the difference between the date register offsets and use sizeof() whenever referencing it. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-8-brgl@bgdev.pl
2020-09-15rtc: rx8010: rename ret to err in rx8010_set_time()Bartosz Golaszewski
All other functions in this driver use 'err' for integer return values. Do the same in rx8010_set_time() for consistency. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-7-brgl@bgdev.pl
2020-09-15rtc: rx8010: use tabs instead of spaces for code formattingBartosz Golaszewski
The define values in this driver are close to their names and they are separated by spaces. Use tabs instead and align all defines. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-6-brgl@bgdev.pl
2020-09-15rtc: rx8010: consolidate local variables of the same typeBartosz Golaszewski
Move local variables of the same type into a single line for better readability. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-5-brgl@bgdev.pl
2020-09-15rtc: rx8010: remove unnecessary bracketsBartosz Golaszewski
Remove brackets wherever they guard a single line. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-4-brgl@bgdev.pl
2020-09-15rtc: rx8010: remove a stray newlineBartosz Golaszewski
Remove an unnecessary newline after requesting the interrupt. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200914154601.32245-3-brgl@bgdev.pl
2020-09-15rtc: rx8010: don't modify the global rtc opsBartosz Golaszewski
The way the driver is implemented is buggy for the (admittedly unlikely) use case where there are two RTCs with one having an interrupt configured and the second not. This is caused by the fact that we use a global rtc_class_ops struct which we modify depending on whether the irq number is present or not. Fix it by using two const ops structs with and without alarm operations. While at it: not being able to request a configured interrupt is an error so don't ignore it and bail out of probe(). Fixes: ed13d89b08e3 ("rtc: Add Epson RX8010SJ RTC driver") Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200914154601.32245-2-brgl@bgdev.pl
2020-09-15rtc: s3c: Simplify with dev_err_probe()Krzysztof Kozlowski
Common pattern of handling deferred probe can be simplified with dev_err_probe(). Less code and the error value gets printed. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200830080937.14367-1-krzk@kernel.org
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-21rtc: fsl-ftm-alarm: update acpi device idPeng Ma
Original device id would conflict with crypto driver, change it. Signed-off-by: Peng Ma <peng.ma@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200818063609.39859-1-ran.wang_1@nxp.com
2020-08-21rtc: ds1307: Clear OSF flag on DS1388 when setting timeChris Packham
Ensure the OSF flag is cleared on the DS1388 when the clock is set. Fixes: df11b323b16f ("rtc: ds1307: handle oscillator failure flags for ds1388 variant") Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200818013543.4283-1-chris.packham@alliedtelesis.co.nz
2020-08-21rtc: ds1307: Ensure oscillator is enabled for DS1388Chris Packham
Similar to the other variants the DS1388 has a bit to stop the oscillator to reduce the power consumption from VBAT. Ensure that the oscillator is enabled when the system is up. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200816235731.21071-1-chris.packham@alliedtelesis.co.nz
2020-08-21rtc: rtc-rs5c313: Convert to module_platform_driver()Geert Uytterhoeven
Reduce boilerplate by using the module_platform_driver() helper. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200814110731.29029-4-geert+renesas@glider.be
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-24 11:17:33 +0000