| Age | Commit message (Collapse) | Author |
|---|
|
For QCA6390, bss peer must be created before vdev is to start. This
change is to start vdev if a bss peer is created. Otherwise, ath11k
delays to start vdev.
This fixes an issue in a case where HT/VHT/HE settings change between
authentication and association, e.g., due to the user space request
to disable HT.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201211051358.9191-1-cjhuang@codeaurora.org
|
|
Peer creation in firmware fails, if last peer deletion
is still in progress.
Hence, add wait for the event after deleting every peer
from host driver to synchronize with firmware.
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-3-git-send-email-mkenna@codeaurora.org
|
|
ath11k should not be spamming these to the logs. If these are important they
should be debug messages, but I just remove them for now.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-10-git-send-email-kvalo@codeaurora.org
|
|
Add the pdev index information in the peer object to validate
the peer creation. Ignore the peer creation request, if the given
MAC address is already present in the peer list with same radio.
If we allow the peer creation in above scenario, FW assert will happen.
Above scenario occurred in two cases, where Multiple AP VAP created in
the same radio.
1. when testing tool sends association request to two AP with same
MAC address
2. when a station do roaming from one AP VAP to another AP VAP.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586343795-21422-1-git-send-email-periyasa@codeaurora.org
|
|
As Hash based reo destination selection is configured,
the decapped packets reach different reo destintion rings
based on the destintaion ring selected for the computed hash (based on
the 5-tuple {ip src/ip dst/src port/dst port/protocol}) by hw and
as configured by driver.
Hence the current implementation of amsdu list based processing after all
the subframes of amsdu are received (since all msdu's for a pdev are
received in same reo dest ring), is not applicable here and hence is
replaced with per msdu based handling as these subframes
can be received in different reo dest rings.
Also, as some of the rx descriptor fields might be valid only for the
first msdu (for ex. received 80211 header, encryption type, etc),
it might not be useful now as we cannot sync between different
subframes received in different rings. Hence do not rely on those
fields and replace them with fieds valid only on per msdu descriptors.
Also cache other details such as encryption type for a peer so that
it can be reused when a packet is received from it.
Co-developed-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.
Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.
Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.
Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.
The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:
https://github.com/kvalo/ath11k-firmware
This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.
The driver has had multiple authors who are listed in alphabetical
order below.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
|
