diff options
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/regulator/bd718x7-regulator.c | 201 |
1 files changed, 176 insertions, 25 deletions
diff --git a/drivers/regulator/bd718x7-regulator.c b/drivers/regulator/bd718x7-regulator.c index ccea133778c8..b2191be49670 100644 --- a/drivers/regulator/bd718x7-regulator.c +++ b/drivers/regulator/bd718x7-regulator.c @@ -350,6 +350,135 @@ static const struct reg_init bd71837_ldo6_inits[] = { }, }; +#define NUM_DVS_BUCKS 4 + +struct of_dvs_setting { + const char *prop; + unsigned int reg; +}; + +static int set_dvs_levels(const struct of_dvs_setting *dvs, + struct device_node *np, + const struct regulator_desc *desc, + struct regmap *regmap) +{ + int ret, i; + unsigned int uv; + + ret = of_property_read_u32(np, dvs->prop, &uv); + if (ret) { + if (ret != -EINVAL) + return ret; + return 0; + } + + for (i = 0; i < desc->n_voltages; i++) { + ret = regulator_desc_list_voltage_linear_range(desc, i); + if (ret < 0) + continue; + if (ret == uv) { + i <<= ffs(desc->vsel_mask) - 1; + ret = regmap_update_bits(regmap, dvs->reg, + DVS_BUCK_RUN_MASK, i); + break; + } + } + return ret; +} + +static int buck4_set_hw_dvs_levels(struct device_node *np, + const struct regulator_desc *desc, + struct regulator_config *cfg) +{ + int ret, i; + const struct of_dvs_setting dvs[] = { + { + .prop = "rohm,dvs-run-voltage", + .reg = BD71837_REG_BUCK4_VOLT_RUN, + }, + }; + + for (i = 0; i < ARRAY_SIZE(dvs); i++) { + ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap); + if (ret) + break; + } + return ret; +} +static int buck3_set_hw_dvs_levels(struct device_node *np, + const struct regulator_desc *desc, + struct regulator_config *cfg) +{ + int ret, i; + const struct of_dvs_setting dvs[] = { + { + .prop = "rohm,dvs-run-voltage", + .reg = BD71837_REG_BUCK3_VOLT_RUN, + }, + }; + + for (i = 0; i < ARRAY_SIZE(dvs); i++) { + ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap); + if (ret) + break; + } + return ret; +} + +static int buck2_set_hw_dvs_levels(struct device_node *np, + const struct regulator_desc *desc, + struct regulator_config *cfg) +{ + int ret, i; + const struct of_dvs_setting dvs[] = { + { + .prop = "rohm,dvs-run-voltage", + .reg = BD718XX_REG_BUCK2_VOLT_RUN, + }, + { + .prop = "rohm,dvs-idle-voltage", + .reg = BD718XX_REG_BUCK2_VOLT_IDLE, + }, + }; + + + + for (i = 0; i < ARRAY_SIZE(dvs); i++) { + ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap); + if (ret) + break; + } + return ret; +} + +static int buck1_set_hw_dvs_levels(struct device_node *np, + const struct regulator_desc *desc, + struct regulator_config *cfg) +{ + int ret, i; + const struct of_dvs_setting dvs[] = { + { + .prop = "rohm,dvs-run-voltage", + .reg = BD718XX_REG_BUCK1_VOLT_RUN, + }, + { + .prop = "rohm,dvs-idle-voltage", + .reg = BD718XX_REG_BUCK1_VOLT_IDLE, + }, + { + .prop = "rohm,dvs-suspend-voltage", + .reg = BD718XX_REG_BUCK1_VOLT_SUSP, + }, + }; + + for (i = 0; i < ARRAY_SIZE(dvs); i++) { + ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap); + if (ret) + break; + } + return ret; +} + static const struct bd718xx_regulator_data bd71847_regulators[] = { { .desc = { @@ -368,6 +497,7 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = { .enable_reg = BD718XX_REG_BUCK1_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck1_set_hw_dvs_levels, }, .init = { .reg = BD718XX_REG_BUCK1_CTRL, @@ -391,6 +521,7 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = { .enable_reg = BD718XX_REG_BUCK2_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck2_set_hw_dvs_levels, }, .init = { .reg = BD718XX_REG_BUCK2_CTRL, @@ -662,6 +793,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = { .enable_reg = BD718XX_REG_BUCK1_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck1_set_hw_dvs_levels, }, .init = { .reg = BD718XX_REG_BUCK1_CTRL, @@ -685,6 +817,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = { .enable_reg = BD718XX_REG_BUCK2_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck2_set_hw_dvs_levels, }, .init = { .reg = BD718XX_REG_BUCK2_CTRL, @@ -708,6 +841,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = { .enable_reg = BD71837_REG_BUCK3_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck3_set_hw_dvs_levels, }, .init = { .reg = BD71837_REG_BUCK3_CTRL, @@ -731,6 +865,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = { .enable_reg = BD71837_REG_BUCK4_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck4_set_hw_dvs_levels, }, .init = { .reg = BD71837_REG_BUCK4_CTRL, @@ -1029,6 +1164,7 @@ static int bd718xx_probe(struct platform_device *pdev) }; int i, j, err; + bool use_snvs; mfd = dev_get_drvdata(pdev->dev.parent); if (!mfd) { @@ -1055,27 +1191,28 @@ static int bd718xx_probe(struct platform_device *pdev) BD718XX_REG_REGLOCK); } - /* At poweroff transition PMIC HW disables EN bit for regulators but - * leaves SEL bit untouched. So if state transition from POWEROFF - * is done to SNVS - then all power rails controlled by SW (having - * SEL bit set) stay disabled as EN is cleared. This may result boot - * failure if any crucial systems are powered by these rails. - * + use_snvs = of_property_read_bool(pdev->dev.parent->of_node, + "rohm,reset-snvs-powered"); + + /* * Change the next stage from poweroff to be READY instead of SNVS * for all reset types because OTP loading at READY will clear SEL * bit allowing HW defaults for power rails to be used */ - err = regmap_update_bits(mfd->regmap, BD718XX_REG_TRANS_COND1, - BD718XX_ON_REQ_POWEROFF_MASK | - BD718XX_SWRESET_POWEROFF_MASK | - BD718XX_WDOG_POWEROFF_MASK | - BD718XX_KEY_L_POWEROFF_MASK, - BD718XX_POWOFF_TO_RDY); - if (err) { - dev_err(&pdev->dev, "Failed to change reset target\n"); - goto err; - } else { - dev_dbg(&pdev->dev, "Changed all resets from SVNS to READY\n"); + if (!use_snvs) { + err = regmap_update_bits(mfd->regmap, BD718XX_REG_TRANS_COND1, + BD718XX_ON_REQ_POWEROFF_MASK | + BD718XX_SWRESET_POWEROFF_MASK | + BD718XX_WDOG_POWEROFF_MASK | + BD718XX_KEY_L_POWEROFF_MASK, + BD718XX_POWOFF_TO_RDY); + if (err) { + dev_err(&pdev->dev, "Failed to change reset target\n"); + goto err; + } else { + dev_dbg(&pdev->dev, + "Changed all resets from SVNS to READY\n"); + } } for (i = 0; i < pmic_regulators[mfd->chip_type].r_amount; i++) { @@ -1098,19 +1235,33 @@ static int bd718xx_probe(struct platform_device *pdev) err = PTR_ERR(rdev); goto err; } - /* Regulator register gets the regulator constraints and + + /* + * Regulator register gets the regulator constraints and * applies them (set_machine_constraints). This should have * turned the control register(s) to correct values and we * can now switch the control from PMIC state machine to the * register interface + * + * At poweroff transition PMIC HW disables EN bit for + * regulators but leaves SEL bit untouched. So if state + * transition from POWEROFF is done to SNVS - then all power + * rails controlled by SW (having SEL bit set) stay disabled + * as EN is cleared. This will result boot failure if any + * crucial systems are powered by these rails. We don't + * enable SW control for crucial regulators if snvs state is + * used */ - err = regmap_update_bits(mfd->regmap, r->init.reg, - r->init.mask, r->init.val); - if (err) { - dev_err(&pdev->dev, - "Failed to write BUCK/LDO SEL bit for (%s)\n", - desc->name); - goto err; + if (!use_snvs || !rdev->constraints->always_on || + !rdev->constraints->boot_on) { + err = regmap_update_bits(mfd->regmap, r->init.reg, + r->init.mask, r->init.val); + if (err) { + dev_err(&pdev->dev, + "Failed to take control for (%s)\n", + desc->name); + goto err; + } } for (j = 0; j < r->additional_init_amnt; j++) { err = regmap_update_bits(mfd->regmap, |