diff options
Diffstat (limited to 'drivers/pinctrl/nomadik/pinctrl-nomadik.c')
| -rw-r--r-- | drivers/pinctrl/nomadik/pinctrl-nomadik.c | 2099 |
1 files changed, 2099 insertions, 0 deletions
diff --git a/drivers/pinctrl/nomadik/pinctrl-nomadik.c b/drivers/pinctrl/nomadik/pinctrl-nomadik.c new file mode 100644 index 000000000000..e7cab07eef47 --- /dev/null +++ b/drivers/pinctrl/nomadik/pinctrl-nomadik.c @@ -0,0 +1,2099 @@ +/* + * Generic GPIO driver for logic cells found in the Nomadik SoC + * + * Copyright (C) 2008,2009 STMicroelectronics + * Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it> + * Rewritten based on work by Prafulla WADASKAR <prafulla.wadaskar@st.com> + * Copyright (C) 2011-2013 Linus Walleij <linus.walleij@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/gpio.h> +#include <linux/spinlock.h> +#include <linux/interrupt.h> +#include <linux/slab.h> +#include <linux/of_device.h> +#include <linux/of_address.h> +#include <linux/pinctrl/machine.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinmux.h> +#include <linux/pinctrl/pinconf.h> +/* Since we request GPIOs from ourself */ +#include <linux/pinctrl/consumer.h> +#include "pinctrl-nomadik.h" +#include "../core.h" + +/* + * The GPIO module in the Nomadik family of Systems-on-Chip is an + * AMBA device, managing 32 pins and alternate functions. The logic block + * is currently used in the Nomadik and ux500. + * + * Symbols in this file are called "nmk_gpio" for "nomadik gpio" + */ + +/* + * pin configurations are represented by 32-bit integers: + * + * bit 0.. 8 - Pin Number (512 Pins Maximum) + * bit 9..10 - Alternate Function Selection + * bit 11..12 - Pull up/down state + * bit 13 - Sleep mode behaviour + * bit 14 - Direction + * bit 15 - Value (if output) + * bit 16..18 - SLPM pull up/down state + * bit 19..20 - SLPM direction + * bit 21..22 - SLPM Value (if output) + * bit 23..25 - PDIS value (if input) + * bit 26 - Gpio mode + * bit 27 - Sleep mode + * + * to facilitate the definition, the following macros are provided + * + * PIN_CFG_DEFAULT - default config (0): + * pull up/down = disabled + * sleep mode = input/wakeup + * direction = input + * value = low + * SLPM direction = same as normal + * SLPM pull = same as normal + * SLPM value = same as normal + * + * PIN_CFG - default config with alternate function + */ + +typedef unsigned long pin_cfg_t; + +#define PIN_NUM_MASK 0x1ff +#define PIN_NUM(x) ((x) & PIN_NUM_MASK) + +#define PIN_ALT_SHIFT 9 +#define PIN_ALT_MASK (0x3 << PIN_ALT_SHIFT) +#define PIN_ALT(x) (((x) & PIN_ALT_MASK) >> PIN_ALT_SHIFT) +#define PIN_GPIO (NMK_GPIO_ALT_GPIO << PIN_ALT_SHIFT) +#define PIN_ALT_A (NMK_GPIO_ALT_A << PIN_ALT_SHIFT) +#define PIN_ALT_B (NMK_GPIO_ALT_B << PIN_ALT_SHIFT) +#define PIN_ALT_C (NMK_GPIO_ALT_C << PIN_ALT_SHIFT) + +#define PIN_PULL_SHIFT 11 +#define PIN_PULL_MASK (0x3 << PIN_PULL_SHIFT) +#define PIN_PULL(x) (((x) & PIN_PULL_MASK) >> PIN_PULL_SHIFT) +#define PIN_PULL_NONE (NMK_GPIO_PULL_NONE << PIN_PULL_SHIFT) +#define PIN_PULL_UP (NMK_GPIO_PULL_UP << PIN_PULL_SHIFT) +#define PIN_PULL_DOWN (NMK_GPIO_PULL_DOWN << PIN_PULL_SHIFT) + +#define PIN_SLPM_SHIFT 13 +#define PIN_SLPM_MASK (0x1 << PIN_SLPM_SHIFT) +#define PIN_SLPM(x) (((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT) +#define PIN_SLPM_MAKE_INPUT (NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT) +#define PIN_SLPM_NOCHANGE (NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT) +/* These two replace the above in DB8500v2+ */ +#define PIN_SLPM_WAKEUP_ENABLE (NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT) +#define PIN_SLPM_WAKEUP_DISABLE (NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT) +#define PIN_SLPM_USE_MUX_SETTINGS_IN_SLEEP PIN_SLPM_WAKEUP_DISABLE + +#define PIN_SLPM_GPIO PIN_SLPM_WAKEUP_ENABLE /* In SLPM, pin is a gpio */ +#define PIN_SLPM_ALTFUNC PIN_SLPM_WAKEUP_DISABLE /* In SLPM, pin is altfunc */ + +#define PIN_DIR_SHIFT 14 +#define PIN_DIR_MASK (0x1 << PIN_DIR_SHIFT) +#define PIN_DIR(x) (((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT) +#define PIN_DIR_INPUT (0 << PIN_DIR_SHIFT) +#define PIN_DIR_OUTPUT (1 << PIN_DIR_SHIFT) + +#define PIN_VAL_SHIFT 15 +#define PIN_VAL_MASK (0x1 << PIN_VAL_SHIFT) +#define PIN_VAL(x) (((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT) +#define PIN_VAL_LOW (0 << PIN_VAL_SHIFT) +#define PIN_VAL_HIGH (1 << PIN_VAL_SHIFT) + +#define PIN_SLPM_PULL_SHIFT 16 +#define PIN_SLPM_PULL_MASK (0x7 << PIN_SLPM_PULL_SHIFT) +#define PIN_SLPM_PULL(x) \ + (((x) & PIN_SLPM_PULL_MASK) >> PIN_SLPM_PULL_SHIFT) +#define PIN_SLPM_PULL_NONE \ + ((1 + NMK_GPIO_PULL_NONE) << PIN_SLPM_PULL_SHIFT) +#define PIN_SLPM_PULL_UP \ + ((1 + NMK_GPIO_PULL_UP) << PIN_SLPM_PULL_SHIFT) +#define PIN_SLPM_PULL_DOWN \ + ((1 + NMK_GPIO_PULL_DOWN) << PIN_SLPM_PULL_SHIFT) + +#define PIN_SLPM_DIR_SHIFT 19 +#define PIN_SLPM_DIR_MASK (0x3 << PIN_SLPM_DIR_SHIFT) +#define PIN_SLPM_DIR(x) \ + (((x) & PIN_SLPM_DIR_MASK) >> PIN_SLPM_DIR_SHIFT) +#define PIN_SLPM_DIR_INPUT ((1 + 0) << PIN_SLPM_DIR_SHIFT) +#define PIN_SLPM_DIR_OUTPUT ((1 + 1) << PIN_SLPM_DIR_SHIFT) + +#define PIN_SLPM_VAL_SHIFT 21 +#define PIN_SLPM_VAL_MASK (0x3 << PIN_SLPM_VAL_SHIFT) +#define PIN_SLPM_VAL(x) \ + (((x) & PIN_SLPM_VAL_MASK) >> PIN_SLPM_VAL_SHIFT) +#define PIN_SLPM_VAL_LOW ((1 + 0) << PIN_SLPM_VAL_SHIFT) +#define PIN_SLPM_VAL_HIGH ((1 + 1) << PIN_SLPM_VAL_SHIFT) + +#define PIN_SLPM_PDIS_SHIFT 23 +#define PIN_SLPM_PDIS_MASK (0x3 << PIN_SLPM_PDIS_SHIFT) +#define PIN_SLPM_PDIS(x) \ + (((x) & PIN_SLPM_PDIS_MASK) >> PIN_SLPM_PDIS_SHIFT) +#define PIN_SLPM_PDIS_NO_CHANGE (0 << PIN_SLPM_PDIS_SHIFT) +#define PIN_SLPM_PDIS_DISABLED (1 << PIN_SLPM_PDIS_SHIFT) +#define PIN_SLPM_PDIS_ENABLED (2 << PIN_SLPM_PDIS_SHIFT) + +#define PIN_LOWEMI_SHIFT 25 +#define PIN_LOWEMI_MASK (0x1 << PIN_LOWEMI_SHIFT) +#define PIN_LOWEMI(x) (((x) & PIN_LOWEMI_MASK) >> PIN_LOWEMI_SHIFT) +#define PIN_LOWEMI_DISABLED (0 << PIN_LOWEMI_SHIFT) +#define PIN_LOWEMI_ENABLED (1 << PIN_LOWEMI_SHIFT) + +#define PIN_GPIOMODE_SHIFT 26 +#define PIN_GPIOMODE_MASK (0x1 << PIN_GPIOMODE_SHIFT) +#define PIN_GPIOMODE(x) (((x) & PIN_GPIOMODE_MASK) >> PIN_GPIOMODE_SHIFT) +#define PIN_GPIOMODE_DISABLED (0 << PIN_GPIOMODE_SHIFT) +#define PIN_GPIOMODE_ENABLED (1 << PIN_GPIOMODE_SHIFT) + +#define PIN_SLEEPMODE_SHIFT 27 +#define PIN_SLEEPMODE_MASK (0x1 << PIN_SLEEPMODE_SHIFT) +#define PIN_SLEEPMODE(x) (((x) & PIN_SLEEPMODE_MASK) >> PIN_SLEEPMODE_SHIFT) +#define PIN_SLEEPMODE_DISABLED (0 << PIN_SLEEPMODE_SHIFT) +#define PIN_SLEEPMODE_ENABLED (1 << PIN_SLEEPMODE_SHIFT) + + +/* Shortcuts. Use these instead of separate DIR, PULL, and VAL. */ +#define PIN_INPUT_PULLDOWN (PIN_DIR_INPUT | PIN_PULL_DOWN) +#define PIN_INPUT_PULLUP (PIN_DIR_INPUT | PIN_PULL_UP) +#define PIN_INPUT_NOPULL (PIN_DIR_INPUT | PIN_PULL_NONE) +#define PIN_OUTPUT_LOW (PIN_DIR_OUTPUT | PIN_VAL_LOW) +#define PIN_OUTPUT_HIGH (PIN_DIR_OUTPUT | PIN_VAL_HIGH) + +#define PIN_SLPM_INPUT_PULLDOWN (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_DOWN) +#define PIN_SLPM_INPUT_PULLUP (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_UP) +#define PIN_SLPM_INPUT_NOPULL (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_NONE) +#define PIN_SLPM_OUTPUT_LOW (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_LOW) +#define PIN_SLPM_OUTPUT_HIGH (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_HIGH) + +#define PIN_CFG_DEFAULT (0) + +#define PIN_CFG(num, alt) \ + (PIN_CFG_DEFAULT |\ + (PIN_NUM(num) | PIN_##alt)) + +#define PIN_CFG_INPUT(num, alt, pull) \ + (PIN_CFG_DEFAULT |\ + (PIN_NUM(num) | PIN_##alt | PIN_INPUT_##pull)) + +#define PIN_CFG_OUTPUT(num, alt, val) \ + (PIN_CFG_DEFAULT |\ + (PIN_NUM(num) | PIN_##alt | PIN_OUTPUT_##val)) + +/* + * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving + * the "gpio" namespace for generic and cross-machine functions + */ + +#define GPIO_BLOCK_SHIFT 5 +#define NMK_GPIO_PER_CHIP (1 << GPIO_BLOCK_SHIFT) + +/* Register in the logic block */ +#define NMK_GPIO_DAT 0x00 +#define NMK_GPIO_DATS 0x04 +#define NMK_GPIO_DATC 0x08 +#define NMK_GPIO_PDIS 0x0c +#define NMK_GPIO_DIR 0x10 +#define NMK_GPIO_DIRS 0x14 +#define NMK_GPIO_DIRC 0x18 +#define NMK_GPIO_SLPC 0x1c +#define NMK_GPIO_AFSLA 0x20 +#define NMK_GPIO_AFSLB 0x24 +#define NMK_GPIO_LOWEMI 0x28 + +#define NMK_GPIO_RIMSC 0x40 +#define NMK_GPIO_FIMSC 0x44 +#define NMK_GPIO_IS 0x48 +#define NMK_GPIO_IC 0x4c +#define NMK_GPIO_RWIMSC 0x50 +#define NMK_GPIO_FWIMSC 0x54 +#define NMK_GPIO_WKS 0x58 +/* These appear in DB8540 and later ASICs */ +#define NMK_GPIO_EDGELEVEL 0x5C +#define NMK_GPIO_LEVEL 0x60 + + +/* Pull up/down values */ +enum nmk_gpio_pull { + NMK_GPIO_PULL_NONE, + NMK_GPIO_PULL_UP, + NMK_GPIO_PULL_DOWN, +}; + +/* Sleep mode */ +enum nmk_gpio_slpm { + NMK_GPIO_SLPM_INPUT, + NMK_GPIO_SLPM_WAKEUP_ENABLE = NMK_GPIO_SLPM_INPUT, + NMK_GPIO_SLPM_NOCHANGE, + NMK_GPIO_SLPM_WAKEUP_DISABLE = NMK_GPIO_SLPM_NOCHANGE, +}; + +struct nmk_gpio_chip { + struct gpio_chip chip; + void __iomem *addr; + struct clk *clk; + unsigned int bank; + unsigned int parent_irq; + int latent_parent_irq; + u32 (*get_latent_status)(unsigned int bank); + void (*set_ioforce)(bool enable); + spinlock_t lock; + bool sleepmode; + /* Keep track of configured edges */ + u32 edge_rising; + u32 edge_falling; + u32 real_wake; + u32 rwimsc; + u32 fwimsc; + u32 rimsc; + u32 fimsc; + u32 pull_up; + u32 lowemi; +}; + +/** + * struct nmk_pinctrl - state container for the Nomadik pin controller + * @dev: containing device pointer + * @pctl: corresponding pin controller device + * @soc: SoC data for this specific chip + * @prcm_base: PRCM register range virtual base + */ +struct nmk_pinctrl { + struct device *dev; + struct pinctrl_dev *pctl; + const struct nmk_pinctrl_soc_data *soc; + void __iomem *prcm_base; +}; + +static struct nmk_gpio_chip * +nmk_gpio_chips[DIV_ROUND_UP(ARCH_NR_GPIOS, NMK_GPIO_PER_CHIP)]; + +static DEFINE_SPINLOCK(nmk_gpio_slpm_lock); + +#define NUM_BANKS ARRAY_SIZE(nmk_gpio_chips) + +static void __nmk_gpio_set_mode(struct nmk_gpio_chip *nmk_chip, + unsigned offset, int gpio_mode) +{ + u32 bit = 1 << offset; + u32 afunc, bfunc; + + afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & ~bit; + bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & ~bit; + if (gpio_mode & NMK_GPIO_ALT_A) + afunc |= bit; + if (gpio_mode & NMK_GPIO_ALT_B) + bfunc |= bit; + writel(afunc, nmk_chip->addr + NMK_GPIO_AFSLA); + writel(bfunc, nmk_chip->addr + NMK_GPIO_AFSLB); +} + +static void __nmk_gpio_set_slpm(struct nmk_gpio_chip *nmk_chip, + unsigned offset, enum nmk_gpio_slpm mode) +{ + u32 bit = 1 << offset; + u32 slpm; + + slpm = readl(nmk_chip->addr + NMK_GPIO_SLPC); + if (mode == NMK_GPIO_SLPM_NOCHANGE) + slpm |= bit; + else + slpm &= ~bit; + writel(slpm, nmk_chip->addr + NMK_GPIO_SLPC); +} + +static void __nmk_gpio_set_pull(struct nmk_gpio_chip *nmk_chip, + unsigned offset, enum nmk_gpio_pull pull) +{ + u32 bit = 1 << offset; + u32 pdis; + + pdis = readl(nmk_chip->addr + NMK_GPIO_PDIS); + if (pull == NMK_GPIO_PULL_NONE) { + pdis |= bit; + nmk_chip->pull_up &= ~bit; + } else { + pdis &= ~bit; + } + + writel(pdis, nmk_chip->addr + NMK_GPIO_PDIS); + + if (pull == NMK_GPIO_PULL_UP) { + nmk_chip->pull_up |= bit; + writel(bit, nmk_chip->addr + NMK_GPIO_DATS); + } else if (pull == NMK_GPIO_PULL_DOWN) { + nmk_chip->pull_up &= ~bit; + writel(bit, nmk_chip->addr + NMK_GPIO_DATC); + } +} + +static void __nmk_gpio_set_lowemi(struct nmk_gpio_chip *nmk_chip, + unsigned offset, bool lowemi) +{ + u32 bit = BIT(offset); + bool enabled = nmk_chip->lowemi & bit; + + if (lowemi == enabled) + return; + + if (lowemi) + nmk_chip->lowemi |= bit; + else + nmk_chip->lowemi &= ~bit; + + writel_relaxed(nmk_chip->lowemi, + nmk_chip->addr + NMK_GPIO_LOWEMI); +} + +static void __nmk_gpio_make_input(struct nmk_gpio_chip *nmk_chip, + unsigned offset) +{ + writel(1 << offset, nmk_chip->addr + NMK_GPIO_DIRC); +} + +static void __nmk_gpio_set_output(struct nmk_gpio_chip *nmk_chip, + unsigned offset, int val) +{ + if (val) + writel(1 << offset, nmk_chip->addr + NMK_GPIO_DATS); + else + writel(1 << offset, nmk_chip->addr + NMK_GPIO_DATC); +} + +static void __nmk_gpio_make_output(struct nmk_gpio_chip *nmk_chip, + unsigned offset, int val) +{ + writel(1 << offset, nmk_chip->addr + NMK_GPIO_DIRS); + __nmk_gpio_set_output(nmk_chip, offset, val); +} + +static void __nmk_gpio_set_mode_safe(struct nmk_gpio_chip *nmk_chip, + unsigned offset, int gpio_mode, + bool glitch) +{ + u32 rwimsc = nmk_chip->rwimsc; + u32 fwimsc = nmk_chip->fwimsc; + + if (glitch && nmk_chip->set_ioforce) { + u32 bit = BIT(offset); + + /* Prevent spurious wakeups */ + writel(rwimsc & ~bit, nmk_chip->addr + NMK_GPIO_RWIMSC); + writel(fwimsc & ~bit, nmk_chip->addr + NMK_GPIO_FWIMSC); + + nmk_chip->set_ioforce(true); + } + + __nmk_gpio_set_mode(nmk_chip, offset, gpio_mode); + + if (glitch && nmk_chip->set_ioforce) { + nmk_chip->set_ioforce(false); + + writel(rwimsc, nmk_chip->addr + NMK_GPIO_RWIMSC); + writel(fwimsc, nmk_chip->addr + NMK_GPIO_FWIMSC); + } +} + +static void +nmk_gpio_disable_lazy_irq(struct nmk_gpio_chip *nmk_chip, unsigned offset) +{ + u32 falling = nmk_chip->fimsc & BIT(offset); + u32 rising = nmk_chip->rimsc & BIT(offset); + int gpio = nmk_chip->chip.base + offset; + int irq = irq_find_mapping(nmk_chip->chip.irqdomain, offset); + struct irq_data *d = irq_get_irq_data(irq); + + if (!rising && !falling) + return; + + if (!d || !irqd_irq_disabled(d)) + return; + + if (rising) { + nmk_chip->rimsc &= ~BIT(offset); + writel_relaxed(nmk_chip->rimsc, + nmk_chip->addr + NMK_GPIO_RIMSC); + } + + if (falling) { + nmk_chip->fimsc &= ~BIT(offset); + writel_relaxed(nmk_chip->fimsc, + nmk_chip->addr + NMK_GPIO_FIMSC); + } + + dev_dbg(nmk_chip->chip.dev, "%d: clearing interrupt mask\n", gpio); +} + +static void nmk_write_masked(void __iomem *reg, u32 mask, u32 value) +{ + u32 val; + + val = readl(reg); + val = ((val & ~mask) | (value & mask)); + writel(val, reg); +} + +static void nmk_prcm_altcx_set_mode(struct nmk_pinctrl *npct, + unsigned offset, unsigned alt_num) +{ + int i; + u16 reg; + u8 bit; + u8 alt_index; + const struct prcm_gpiocr_altcx_pin_desc *pin_desc; + const u16 *gpiocr_regs; + + if (!npct->prcm_base) + return; + + if (alt_num > PRCM_IDX_GPIOCR_ALTC_MAX) { + dev_err(npct->dev, "PRCM GPIOCR: alternate-C%i is invalid\n", + alt_num); + return; + } + + for (i = 0 ; i < npct->soc->npins_altcx ; i++) { + if (npct->soc->altcx_pins[i].pin == offset) + break; + } + if (i == npct->soc->npins_altcx) { + dev_dbg(npct->dev, "PRCM GPIOCR: pin %i is not found\n", + offset); + return; + } + + pin_desc = npct->soc->altcx_pins + i; + gpiocr_regs = npct->soc->prcm_gpiocr_registers; + + /* + * If alt_num is NULL, just clear current ALTCx selection + * to make sure we come back to a pure ALTC selection + */ + if (!alt_num) { + for (i = 0 ; i < PRCM_IDX_GPIOCR_ALTC_MAX ; i++) { + if (pin_desc->altcx[i].used == true) { + reg = gpiocr_regs[pin_desc->altcx[i].reg_index]; + bit = pin_desc->altcx[i].control_bit; + if (readl(npct->prcm_base + reg) & BIT(bit)) { + nmk_write_masked(npct->prcm_base + reg, BIT(bit), 0); + dev_dbg(npct->dev, + "PRCM GPIOCR: pin %i: alternate-C%i has been disabled\n", + offset, i+1); + } + } + } + return; + } + + alt_index = alt_num - 1; + if (pin_desc->altcx[alt_index].used == false) { + dev_warn(npct->dev, + "PRCM GPIOCR: pin %i: alternate-C%i does not exist\n", + offset, alt_num); + return; + } + + /* + * Check if any other ALTCx functions are activated on this pin + * and disable it first. + */ + for (i = 0 ; i < PRCM_IDX_GPIOCR_ALTC_MAX ; i++) { + if (i == alt_index) + continue; + if (pin_desc->altcx[i].used == true) { + reg = gpiocr_regs[pin_desc->altcx[i].reg_index]; + bit = pin_desc->altcx[i].control_bit; + if (readl(npct->prcm_base + reg) & BIT(bit)) { + nmk_write_masked(npct->prcm_base + reg, BIT(bit), 0); + dev_dbg(npct->dev, + "PRCM GPIOCR: pin %i: alternate-C%i has been disabled\n", + offset, i+1); + } + } + } + + reg = gpiocr_regs[pin_desc->altcx[alt_index].reg_index]; + bit = pin_desc->altcx[alt_index].control_bit; + dev_dbg(npct->dev, "PRCM GPIOCR: pin %i: alternate-C%i has been selected\n", + offset, alt_index+1); + nmk_write_masked(npct->prcm_base + reg, BIT(bit), BIT(bit)); +} + +/* + * Safe sequence used to switch IOs between GPIO and Alternate-C mode: + * - Save SLPM registers + * - Set SLPM=0 for the IOs you want to switch and others to 1 + * - Configure the GPIO registers for the IOs that are being switched + * - Set IOFORCE=1 + * - Modify the AFLSA/B registers for the IOs that are being switched + * - Set IOFORCE=0 + * - Restore SLPM registers + * - Any spurious wake up event during switch sequence to be ignored and + * cleared + */ +static void nmk_gpio_glitch_slpm_init(unsigned int *slpm) +{ + int i; + + for (i = 0; i < NUM_BANKS; i++) { + struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; + unsigned int temp = slpm[i]; + + if (!chip) + break; + + clk_enable(chip->clk); + + slpm[i] = readl(chip->addr + NMK_GPIO_SLPC); + writel(temp, chip->addr + NMK_GPIO_SLPC); + } +} + +static void nmk_gpio_glitch_slpm_restore(unsigned int *slpm) +{ + int i; + + for (i = 0; i < NUM_BANKS; i++) { + struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; + + if (!chip) + break; + + writel(slpm[i], chip->addr + NMK_GPIO_SLPC); + + clk_disable(chip->clk); + } +} + +static int __maybe_unused nmk_prcm_gpiocr_get_mode(struct pinctrl_dev *pctldev, int gpio) +{ + int i; + u16 reg; + u8 bit; + struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); + const struct prcm_gpiocr_altcx_pin_desc *pin_desc; + const u16 *gpiocr_regs; + + if (!npct->prcm_base) + return NMK_GPIO_ALT_C; + + for (i = 0; i < npct->soc->npins_altcx; i++) { + if (npct->soc->altcx_pins[i].pin == gpio) + break; + } + if (i == npct->soc->npins_altcx) + return NMK_GPIO_ALT_C; + + pin_desc = npct->soc->altcx_pins + i; + gpiocr_regs = npct->soc->prcm_gpiocr_registers; + for (i = 0; i < PRCM_IDX_GPIOCR_ALTC_MAX; i++) { + if (pin_desc->altcx[i].used == true) { + reg = gpiocr_regs[pin_desc->altcx[i].reg_index]; + bit = pin_desc->altcx[i].control_bit; + if (readl(npct->prcm_base + reg) & BIT(bit)) + return NMK_GPIO_ALT_C+i+1; + } + } + return NMK_GPIO_ALT_C; +} + +int nmk_gpio_get_mode(int gpio) +{ + struct nmk_gpio_chip *nmk_chip; + u32 afunc, bfunc, bit; + + nmk_chip = nmk_gpio_chips[gpio / NMK_GPIO_PER_CHIP]; + if (!nmk_chip) + return -EINVAL; + + bit = 1 << (gpio % NMK_GPIO_PER_CHIP); + + clk_enable(nmk_chip->clk); + + afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & bit; + bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & bit; + + clk_disable(nmk_chip->clk); + + return (afunc ? NMK_GPIO_ALT_A : 0) | (bfunc ? NMK_GPIO_ALT_B : 0); +} +EXPORT_SYMBOL(nmk_gpio_get_mode); + + +/* IRQ functions */ +static inline int nmk_gpio_get_bitmask(int gpio) +{ + return 1 << (gpio % NMK_GPIO_PER_CHIP); +} + +static void nmk_gpio_irq_ack(struct irq_data *d) +{ + struct gpio_chip *chip = irq_data_get_irq_chip_data(d); + struct nmk_gpio_chip *nmk_chip = container_of(chip, struct nmk_gpio_chip, chip); + + clk_enable(nmk_chip->clk); + writel(nmk_gpio_get_bitmask(d->hwirq), nmk_chip->addr + NMK_GPIO_IC); + clk_disable(nmk_chip->clk); +} + +enum nmk_gpio_irq_type { + NORMAL, + WAKE, +}; + +static void __nmk_gpio_irq_modify(struct nmk_gpio_chip *nmk_chip, + int gpio, enum nmk_gpio_irq_type which, + bool enable) +{ + u32 bitmask = nmk_gpio_get_bitmask(gpio); + u32 *rimscval; + u32 *fimscval; + u32 rimscreg; + u32 fimscreg; + + if (which == NORMAL) { + rimscreg = NMK_GPIO_RIMSC; + fimscreg = NMK_GPIO_FIMSC; + rimscval = &nmk_chip->rimsc; + fimscval = &nmk_chip->fimsc; + } else { + rimscreg = NMK_GPIO_RWIMSC; + fimscreg = NMK_GPIO_FWIMSC; + rimscval = &nmk_chip->rwimsc; + fimscval = &nmk_chip->fwimsc; + } + + /* we must individually set/clear the two edges */ + if (nmk_chip->edge_rising & bitmask) { + if (enable) + *rimscval |= bitmask; + else + *rimscval &= ~bitmask; + writel(*rimscval, nmk_chip->addr + rimscreg); + } + if (nmk_chip->edge_falling & bitmask) { + if (enable) + *fimscval |= bitmask; + else + *fimscval &= ~bitmask; + writel(*fimscval, nmk_chip->addr + fimscreg); + } +} + +static void __nmk_gpio_set_wake(struct nmk_gpio_chip *nmk_chip, + int gpio, bool on) +{ + /* + * Ensure WAKEUP_ENABLE is on. No need to disable it if wakeup is + * disabled, since setting SLPM to 1 increases power consumption, and + * wakeup is anyhow controlled by the RIMSC and FIMSC registers. + */ + if (nmk_chip->sleepmode && on) { + __nmk_gpio_set_slpm(nmk_chip, gpio % NMK_GPIO_PER_CHIP, + NMK_GPIO_SLPM_WAKEUP_ENABLE); + } + + __nmk_gpio_irq_modify(nmk_chip, gpio, WAKE, on); +} + +static int nmk_gpio_irq_maskunmask(struct irq_data *d, bool enable) +{ + struct nmk_gpio_chip *nmk_chip; + unsigned long flags; + u32 bitmask; + + nmk_chip = irq_data_get_irq_chip_data(d); + bitmask = nmk_gpio_get_bitmask(d->hwirq); + if (!nmk_chip) + return -EINVAL; + + clk_enable(nmk_chip->clk); + spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); + spin_lock(&nmk_chip->lock); + + __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, enable); + + if (!(nmk_chip->real_wake & bitmask)) + __nmk_gpio_set_wake(nmk_chip, d->hwirq, enable); + + spin_unlock(&nmk_chip->lock); + spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); + clk_disable(nmk_chip->clk); + + return 0; +} + +static void nmk_gpio_irq_mask(struct irq_data *d) +{ + nmk_gpio_irq_maskunmask(d, false); +} + +static void nmk_gpio_irq_unmask(struct irq_data *d) +{ + nmk_gpio_irq_maskunmask(d, true); +} + +static int nmk_gpio_irq_set_wake(struct irq_data *d, unsigned int on) +{ + struct nmk_gpio_chip *nmk_chip; + unsigned long flags; + u32 bitmask; + + nmk_chip = irq_data_get_irq_chip_data(d); + if (!nmk_chip) + return -EINVAL; + bitmask = nmk_gpio_get_bitmask(d->hwirq); + + clk_enable(nmk_chip->clk); + spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); + spin_lock(&nmk_chip->lock); + + if (irqd_irq_disabled(d)) + __nmk_gpio_set_wake(nmk_chip, d->hwirq, on); + + if (on) + nmk_chip->real_wake |= bitmask; + else + nmk_chip->real_wake &= ~bitmask; + + spin_unlock(&nmk_chip->lock); + spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); + clk_disable(nmk_chip->clk); + + return 0; +} + +static int nmk_gpio_irq_set_type(struct irq_data *d, unsigned int type) +{ + bool enabled = !irqd_irq_disabled(d); + bool wake = irqd_is_wakeup_set(d); + struct nmk_gpio_chip *nmk_chip; + unsigned long flags; + u32 bitmask; + + nmk_chip = irq_data_get_irq_chip_data(d); + bitmask = nmk_gpio_get_bitmask(d->hwirq); + if (!nmk_chip) + return -EINVAL; + if (type & IRQ_TYPE_LEVEL_HIGH) + return -EINVAL; + if (type & IRQ_TYPE_LEVEL_LOW) + return -EINVAL; + + clk_enable(nmk_chip->clk); + spin_lock_irqsave(&nmk_chip->lock, flags); + + if (enabled) + __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, false); + + if (enabled || wake) + __nmk_gpio_irq_modify(nmk_chip, d->hwirq, WAKE, false); + + nmk_chip->edge_rising &= ~bitmask; + if (type & IRQ_TYPE_EDGE_RISING) + nmk_chip->edge_rising |= bitmask; + + nmk_chip->edge_falling &= ~bitmask; + if (type & IRQ_TYPE_EDGE_FALLING) + nmk_chip->edge_falling |= bitmask; + + if (enabled) + __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, true); + + if (enabled || wake) + __nmk_gpio_irq_modify(nmk_chip, d->hwirq, WAKE, true); + + spin_unlock_irqrestore(&nmk_chip->lock, flags); + clk_disable(nmk_chip->clk); + + return 0; +} + +static unsigned int nmk_gpio_irq_startup(struct irq_data *d) +{ + struct nmk_gpio_chip *nmk_chip = irq_data_get_irq_chip_data(d); + + clk_enable(nmk_chip->clk); + nmk_gpio_irq_unmask(d); + return 0; +} + +static void nmk_gpio_irq_shutdown(struct irq_data *d) +{ + struct nmk_gpio_chip *nmk_chip = irq_data_get_irq_chip_data(d); + + nmk_gpio_irq_mask(d); + clk_disable(nmk_chip->clk); +} + +static struct irq_chip nmk_gpio_irq_chip = { + .name = "Nomadik-GPIO", + .irq_ack = nmk_gpio_irq_ack, + .irq_mask = nmk_gpio_irq_mask, + .irq_unmask = nmk_gpio_irq_unmask, + .irq_set_type = nmk_gpio_irq_set_type, + .irq_set_wake = nmk_gpio_irq_set_wake, + .irq_startup = nmk_gpio_irq_startup, + .irq_shutdown = nmk_gpio_irq_shutdown, + .flags = IRQCHIP_MASK_ON_SUSPEND, +}; + +static void __nmk_gpio_irq_handler(unsigned int irq, struct irq_desc *desc, + u32 status) +{ + struct irq_chip *host_chip = irq_get_chip(irq); + struct gpio_chip *chip = irq_desc_get_handler_data(desc); + + chained_irq_enter(host_chip, desc); + + while (status) { + int bit = __ffs(status); + + generic_handle_irq(irq_find_mapping(chip->irqdomain, bit)); + status &= ~BIT(bit); + } + + chained_irq_exit(host_chip, desc); +} + +static void nmk_gpio_irq_handler(unsigned int irq, struct irq_desc *desc) +{ + struct gpio_chip *chip = irq_desc_get_handler_data(desc); + struct nmk_gpio_chip *nmk_chip = container_of(chip, struct nmk_gpio_chip, chip); + u32 status; + + clk_enable(nmk_chip->clk); + status = readl(nmk_chip->addr + NMK_GPIO_IS); + clk_disable(nmk_chip->clk); + + __nmk_gpio_irq_handler(irq, desc, status); +} + +static void nmk_gpio_latent_irq_handler(unsigned int irq, + struct irq_desc *desc) +{ + struct gpio_chip *chip = irq_desc_get_handler_data(desc); + struct nmk_gpio_chip *nmk_chip = container_of(chip, struct nmk_gpio_chip, chip); + u32 status = nmk_chip->get_latent_status(nmk_chip->bank); + + __nmk_gpio_irq_handler(irq, desc, status); +} + +/* I/O Functions */ + +static int nmk_gpio_request(struct gpio_chip *chip, unsigned offset) +{ + /* + * Map back to global GPIO space and request muxing, the direction + * parameter does not matter for this controller. + */ + int gpio = chip->base + offset; + + return pinctrl_request_gpio(gpio); +} + +static void nmk_gpio_free(struct gpio_chip *chip, unsigned offset) +{ + int gpio = chip->base + offset; + + pinctrl_free_gpio(gpio); +} + +static int nmk_gpio_make_input(struct gpio_chip *chip, unsigned offset) +{ + struct nmk_gpio_chip *nmk_chip = + container_of(chip, struct nmk_gpio_chip, chip); + + clk_enable(nmk_chip->clk); + + writel(1 << offset, nmk_chip->addr + NMK_GPIO_DIRC); + + clk_disable(nmk_chip->clk); + + return 0; +} + +static int nmk_gpio_get_input(struct gpio_chip *chip, unsigned offset) +{ + struct nmk_gpio_chip *nmk_chip = + container_of(chip, struct nmk_gpio_chip, chip); + u32 bit = 1 << offset; + int value; + + clk_enable(nmk_chip->clk); + + value = (readl(nmk_chip->addr + NMK_GPIO_DAT) & bit) != 0; + + clk_disable(nmk_chip->clk); + + return value; +} + +static void nmk_gpio_set_output(struct gpio_chip *chip, unsigned offset, + int val) +{ + struct nmk_gpio_chip *nmk_chip = + container_of(chip, struct nmk_gpio_chip, chip); + + clk_enable(nmk_chip->clk); + + __nmk_gpio_set_output(nmk_chip, offset, val); + + clk_disable(nmk_chip->clk); +} + +static int nmk_gpio_make_output(struct gpio_chip *chip, unsigned offset, + int val) +{ + struct nmk_gpio_chip *nmk_chip = + container_of(chip, struct nmk_gpio_chip, chip); + + clk_enable(nmk_chip->clk); + + __nmk_gpio_make_output(nmk_chip, offset, val); + + clk_disable(nmk_chip->clk); + + return 0; +} + +#ifdef CONFIG_DEBUG_FS + +#include <linux/seq_file.h> + +static void nmk_gpio_dbg_show_one(struct seq_file *s, + struct pinctrl_dev *pctldev, struct gpio_chip *chip, + unsigned offset, unsigned gpio) +{ + const char *label = gpiochip_is_requested(chip, offset); + struct nmk_gpio_chip *nmk_chip = + container_of(chip, struct nmk_gpio_chip, chip); + int mode; + bool is_out; + bool pull; + u32 bit = 1 << offset; + const char *modes[] = { + [NMK_GPIO_ALT_GPIO] = "gpio", + [NMK_GPIO_ALT_A] = "altA", + [NMK_GPIO_ALT_B] = "altB", + [NMK_GPIO_ALT_C] = "altC", + [NMK_GPIO_ALT_C+1] = "altC1", + [NMK_GPIO_ALT_C+2] = "altC2", + [NMK_GPIO_ALT_C+3] = "altC3", + [NMK_GPIO_ALT_C+4] = "altC4", + }; + + clk_enable(nmk_chip->clk); + is_out = !!(readl(nmk_chip->addr + NMK_GPIO_DIR) & bit); + pull = !(readl(nmk_chip->addr + NMK_GPIO_PDIS) & bit); + mode = nmk_gpio_get_mode(gpio); + if ((mode == NMK_GPIO_ALT_C) && pctldev) + mode = nmk_prcm_gpiocr_get_mode(pctldev, gpio); + + seq_printf(s, " gpio-%-3d (%-20.20s) %s %s %s %s", + gpio, label ?: "(none)", + is_out ? "out" : "in ", + chip->get + ? (chip->get(chip, offset) ? "hi" : "lo") + : "? ", + (mode < 0) ? "unknown" : modes[mode], + pull ? "pull" : "none"); + + if (!is_out) { + int irq = gpio_to_irq(gpio); + struct irq_desc *desc = irq_to_desc(irq); + + /* This races with request_irq(), set_irq_type(), + * and set_irq_wake() ... but those are "rare". + */ + if (irq > 0 && desc && desc->action) { + char *trigger; + u32 bitmask = nmk_gpio_get_bitmask(gpio); + + if (nmk_chip->edge_rising & bitmask) + trigger = "edge-rising"; + else if (nmk_chip->edge_falling & bitmask) + trigger = "edge-falling"; + else + trigger = "edge-undefined"; + + seq_printf(s, " irq-%d %s%s", + irq, trigger, + irqd_is_wakeup_set(&desc->irq_data) + ? " wakeup" : ""); + } + } + clk_disable(nmk_chip->clk); +} + +static void nmk_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip) +{ + unsigned i; + unsigned gpio = chip->base; + + for (i = 0; i < chip->ngpio; i++, gpio++) { + nmk_gpio_dbg_show_one(s, NULL, chip, i, gpio); + seq_printf(s, "\n"); + } +} + +#else +static inline void nmk_gpio_dbg_show_one(struct seq_file *s, + struct pinctrl_dev *pctldev, + struct gpio_chip *chip, + unsigned offset, unsigned gpio) +{ +} +#define nmk_gpio_dbg_show NULL +#endif + +/* This structure is replicated for each GPIO block allocated at probe time */ +static struct gpio_chip nmk_gpio_template = { + .request = nmk_gpio_request, + .free = nmk_gpio_free, + .direction_input = nmk_gpio_make_input, + .get = nmk_gpio_get_input, + .direction_output = nmk_gpio_make_output, + .set = nmk_gpio_set_output, + .dbg_show = nmk_gpio_dbg_show, + .can_sleep = false, +}; + +void nmk_gpio_clocks_enable(void) +{ + int i; + + for (i = 0; i < NUM_BANKS; i++) { + struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; + + if (!chip) + continue; + + clk_enable(chip->clk); + } +} + +void nmk_gpio_clocks_disable(void) +{ + int i; + + for (i = 0; i < NUM_BANKS; i++) { + struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; + + if (!chip) + continue; + + clk_disable(chip->clk); + } +} + +/* + * Called from the suspend/resume path to only keep the real wakeup interrupts + * (those that have had set_irq_wake() called on them) as wakeup interrupts, + * and not the rest of the interrupts which we needed to have as wakeups for + * cpuidle. + * + * PM ops are not used since this needs to be done at the end, after all the + * other drivers are done with their suspend callbacks. + */ +void nmk_gpio_wakeups_suspend(void) +{ + int i; + + for (i = 0; i < NUM_BANKS; i++) { + struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; + + if (!chip) + break; + + clk_enable(chip->clk); + + writel(chip->rwimsc & chip->real_wake, + chip->addr + NMK_GPIO_RWIMSC); + writel(chip->fwimsc & chip->real_wake, + chip->addr + NMK_GPIO_FWIMSC); + + clk_disable(chip->clk); + } +} + +void nmk_gpio_wakeups_resume(void) +{ + int i; + + for (i = 0; i < NUM_BANKS; i++) { + struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; + + if (!chip) + break; + + clk_enable(chip->clk); + + writel(chip->rwimsc, chip->addr + NMK_GPIO_RWIMSC); + writel(chip->fwimsc, chip->addr + NMK_GPIO_FWIMSC); + + clk_disable(chip->clk); + } +} + +/* + * Read the pull up/pull down status. + * A bit set in 'pull_up' means that pull up + * is selected if pull is enabled in PDIS register. + * Note: only pull up/down set via this driver can + * be detected due to HW limitations. + */ +void nmk_gpio_read_pull(int gpio_bank, u32 *pull_up) +{ + if (gpio_bank < NUM_BANKS) { + struct nmk_gpio_chip *chip = nmk_gpio_chips[gpio_bank]; + + if (!chip) + return; + + *pull_up = chip->pull_up; + } +} + +static int nmk_gpio_probe(struct platform_device *dev) +{ + struct device_node *np = dev->dev.of_node; + struct nmk_gpio_chip *nmk_chip; + struct gpio_chip *chip; + struct resource *res; + struct clk *clk; |