diff options
Diffstat (limited to 'drivers/iio')
98 files changed, 7646 insertions, 810 deletions
diff --git a/drivers/iio/accel/st_accel_core.c b/drivers/iio/accel/st_accel_core.c index 2e37f8a6d8cf..7b837641f166 100644 --- a/drivers/iio/accel/st_accel_core.c +++ b/drivers/iio/accel/st_accel_core.c @@ -15,7 +15,6 @@ #include <linux/types.h> #include <linux/interrupt.h> #include <linux/i2c.h> -#include <linux/gpio.h> #include <linux/irq.h> #include <linux/iio/iio.h> #include <linux/iio/sysfs.h> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig index 0b21dd405dd5..5d8540b7b427 100644 --- a/drivers/iio/adc/Kconfig +++ b/drivers/iio/adc/Kconfig @@ -55,6 +55,16 @@ config AD7291 To compile this driver as a module, choose M here: the module will be called ad7291. +config AD7292 + tristate "Analog Devices AD7292 ADC driver" + depends on SPI + help + Say yes here to build support for Analog Devices AD7292 + 8 Channel ADC with temperature sensor. + + To compile this driver as a module, choose M here: the + module will be called ad7292. + config AD7298 tristate "Analog Devices AD7298 ADC driver" depends on SPI @@ -442,6 +452,17 @@ config INGENIC_ADC This driver can also be built as a module. If so, the module will be called ingenic_adc. +config INTEL_MRFLD_ADC + tristate "Intel Merrifield Basin Cove ADC driver" + depends on INTEL_SOC_PMIC_MRFLD + help + Say yes here to have support for Basin Cove power management IC (PMIC) ADC + device. Depending on platform configuration, this general purpose ADC can + be used for sampling sensors such as thermal resistors. + + To compile this driver as a module, choose M here: the module will be + called intel_mrfld_adc. + config IMX7D_ADC tristate "Freescale IMX7D ADC driver" depends on ARCH_MXC || COMPILE_TEST @@ -518,8 +539,8 @@ config MAX1027 select IIO_BUFFER select IIO_TRIGGERED_BUFFER help - Say yes here to build support for Maxim SPI ADC models - max1027, max1029 and max1031. + Say yes here to build support for Maxim SPI {10,12}-bit ADC models: + max1027, max1029, max1031, max1227, max1229 and max1231. To compile this driver as a module, choose M here: the module will be called max1027. diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile index fc1b6ebb0cde..a1f1fbec0f87 100644 --- a/drivers/iio/adc/Makefile +++ b/drivers/iio/adc/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_AD_SIGMA_DELTA) += ad_sigma_delta.o obj-$(CONFIG_AD7124) += ad7124.o obj-$(CONFIG_AD7266) += ad7266.o obj-$(CONFIG_AD7291) += ad7291.o +obj-$(CONFIG_AD7292) += ad7292.o obj-$(CONFIG_AD7298) += ad7298.o obj-$(CONFIG_AD7923) += ad7923.o obj-$(CONFIG_AD7476) += ad7476.o @@ -43,6 +44,7 @@ obj-$(CONFIG_HX711) += hx711.o obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o obj-$(CONFIG_INGENIC_ADC) += ingenic-adc.o +obj-$(CONFIG_INTEL_MRFLD_ADC) += intel_mrfld_adc.o obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o obj-$(CONFIG_LPC18XX_ADC) += lpc18xx_adc.o obj-$(CONFIG_LPC32XX_ADC) += lpc32xx_adc.o diff --git a/drivers/iio/adc/ad7292.c b/drivers/iio/adc/ad7292.c new file mode 100644 index 000000000000..a6798f7dfdb8 --- /dev/null +++ b/drivers/iio/adc/ad7292.c @@ -0,0 +1,350 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Analog Devices AD7292 SPI ADC driver + * + * Copyright 2019 Analog Devices Inc. + */ + +#include <linux/bitfield.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/regulator/consumer.h> +#include <linux/spi/spi.h> + +#include <linux/iio/iio.h> + +#define ADI_VENDOR_ID 0x0018 + +/* AD7292 registers definition */ +#define AD7292_REG_VENDOR_ID 0x00 +#define AD7292_REG_CONF_BANK 0x05 +#define AD7292_REG_CONV_COMM 0x0E +#define AD7292_REG_ADC_CH(x) (0x10 + (x)) + +/* AD7292 configuration bank subregisters definition */ +#define AD7292_BANK_REG_VIN_RNG0 0x10 +#define AD7292_BANK_REG_VIN_RNG1 0x11 +#define AD7292_BANK_REG_SAMP_MODE 0x12 + +#define AD7292_RD_FLAG_MSK(x) (BIT(7) | ((x) & 0x3F)) + +/* AD7292_REG_ADC_CONVERSION */ +#define AD7292_ADC_DATA_MASK GENMASK(15, 6) +#define AD7292_ADC_DATA(x) FIELD_GET(AD7292_ADC_DATA_MASK, x) + +/* AD7292_CHANNEL_SAMPLING_MODE */ +#define AD7292_CH_SAMP_MODE(reg, ch) (((reg) >> 8) & BIT(ch)) + +/* AD7292_CHANNEL_VIN_RANGE */ +#define AD7292_CH_VIN_RANGE(reg, ch) ((reg) & BIT(ch)) + +#define AD7292_VOLTAGE_CHAN(_chan) \ +{ \ + .type = IIO_VOLTAGE, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ + BIT(IIO_CHAN_INFO_SCALE), \ + .indexed = 1, \ + .channel = _chan, \ +} + +static const struct iio_chan_spec ad7292_channels[] = { + AD7292_VOLTAGE_CHAN(0), + AD7292_VOLTAGE_CHAN(1), + AD7292_VOLTAGE_CHAN(2), + AD7292_VOLTAGE_CHAN(3), + AD7292_VOLTAGE_CHAN(4), + AD7292_VOLTAGE_CHAN(5), + AD7292_VOLTAGE_CHAN(6), + AD7292_VOLTAGE_CHAN(7) +}; + +static const struct iio_chan_spec ad7292_channels_diff[] = { + { + .type = IIO_VOLTAGE, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + .indexed = 1, + .differential = 1, + .channel = 0, + .channel2 = 1, + }, + AD7292_VOLTAGE_CHAN(2), + AD7292_VOLTAGE_CHAN(3), + AD7292_VOLTAGE_CHAN(4), + AD7292_VOLTAGE_CHAN(5), + AD7292_VOLTAGE_CHAN(6), + AD7292_VOLTAGE_CHAN(7) +}; + +struct ad7292_state { + struct spi_device *spi; + struct regulator *reg; + unsigned short vref_mv; + + __be16 d16 ____cacheline_aligned; + u8 d8[2]; +}; + +static int ad7292_spi_reg_read(struct ad7292_state *st, unsigned int addr) +{ + int ret; + + st->d8[0] = AD7292_RD_FLAG_MSK(addr); + + ret = spi_write_then_read(st->spi, st->d8, 1, &st->d16, 2); + if (ret < 0) + return ret; + + return be16_to_cpu(st->d16); +} + +static int ad7292_spi_subreg_read(struct ad7292_state *st, unsigned int addr, + unsigned int sub_addr, unsigned int len) +{ + unsigned int shift = 16 - (8 * len); + int ret; + + st->d8[0] = AD7292_RD_FLAG_MSK(addr); + st->d8[1] = sub_addr; + + ret = spi_write_then_read(st->spi, st->d8, 2, &st->d16, len); + if (ret < 0) + return ret; + + return (be16_to_cpu(st->d16) >> shift); +} + +static int ad7292_single_conversion(struct ad7292_state *st, + unsigned int chan_addr) +{ + int ret; + + struct spi_transfer t[] = { + { + .tx_buf = &st->d8, + .len = 4, + .delay_usecs = 6, + }, { + .rx_buf = &st->d16, + .len = 2, + }, + }; + + st->d8[0] = chan_addr; + st->d8[1] = AD7292_RD_FLAG_MSK(AD7292_REG_CONV_COMM); + + ret = spi_sync_transfer(st->spi, t, ARRAY_SIZE(t)); + + if (ret < 0) + return ret; + + return be16_to_cpu(st->d16); +} + +static int ad7292_vin_range_multiplier(struct ad7292_state *st, int channel) +{ + int samp_mode, range0, range1, factor = 1; + + /* + * Every AD7292 ADC channel may have its input range adjusted according + * to the settings at the ADC sampling mode and VIN range subregisters. + * For a given channel, the minimum input range is equal to Vref, and it + * may be increased by a multiplier factor of 2 or 4 according to the + * following rule: + * If channel is being sampled with respect to AGND: + * factor = 4 if VIN range0 and VIN range1 equal 0 + * factor = 2 if only one of VIN ranges equal 1 + * factor = 1 if both VIN range0 and VIN range1 equal 1 + * If channel is being sampled with respect to AVDD: + * factor = 4 if VIN range0 and VIN range1 equal 0 + * Behavior is undefined if any of VIN range doesn't equal 0 + */ + + samp_mode = ad7292_spi_subreg_read(st, AD7292_REG_CONF_BANK, + AD7292_BANK_REG_SAMP_MODE, 2); + + if (samp_mode < 0) + return samp_mode; + + range0 = ad7292_spi_subreg_read(st, AD7292_REG_CONF_BANK, + AD7292_BANK_REG_VIN_RNG0, 2); + + if (range0 < 0) + return range0; + + range1 = ad7292_spi_subreg_read(st, AD7292_REG_CONF_BANK, + AD7292_BANK_REG_VIN_RNG1, 2); + + if (range1 < 0) + return range1; + + if (AD7292_CH_SAMP_MODE(samp_mode, channel)) { + /* Sampling with respect to AGND */ + if (!AD7292_CH_VIN_RANGE(range0, channel)) + factor *= 2; + + if (!AD7292_CH_VIN_RANGE(range1, channel)) + factor *= 2; + + } else { + /* Sampling with respect to AVDD */ + if (AD7292_CH_VIN_RANGE(range0, channel) || + AD7292_CH_VIN_RANGE(range1, channel)) + return -EPERM; + + factor = 4; + } + + return factor; +} + +static int ad7292_read_raw(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + int *val, int *val2, long info) +{ + struct ad7292_state *st = iio_priv(indio_dev); + unsigned int ch_addr; + int ret; + + switch (info) { + case IIO_CHAN_INFO_RAW: + ch_addr = AD7292_REG_ADC_CH(chan->channel); + ret = ad7292_single_conversion(st, ch_addr); + if (ret < 0) + return ret; + + *val = AD7292_ADC_DATA(ret); + + return IIO_VAL_INT; + case IIO_CHAN_INFO_SCALE: + /* + * To convert a raw value to standard units, the IIO defines + * this formula: Scaled value = (raw + offset) * scale. + * For the scale to be a correct multiplier for (raw + offset), + * it must be calculated as the input range divided by the + * number of possible distinct input values. Given the ADC data + * is 10 bit long, it may assume 2^10 distinct values. + * Hence, scale = range / 2^10. The IIO_VAL_FRACTIONAL_LOG2 + * return type indicates to the IIO API to divide *val by 2 to + * the power of *val2 when returning from read_raw. + */ + + ret = ad7292_vin_range_multiplier(st, chan->channel); + if (ret < 0) + return ret; + + *val = st->vref_mv * ret; + *val2 = 10; + return IIO_VAL_FRACTIONAL_LOG2; + default: + break; + } + return -EINVAL; +} + +static const struct iio_info ad7292_info = { + .read_raw = ad7292_read_raw, +}; + +static void ad7292_regulator_disable(void *data) +{ + struct ad7292_state *st = data; + + regulator_disable(st->reg); +} + +static int ad7292_probe(struct spi_device *spi) +{ + struct ad7292_state *st; + struct iio_dev *indio_dev; + struct device_node *child; + bool diff_channels = 0; + int ret; + + indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); + if (!indio_dev) + return -ENOMEM; + + st = iio_priv(indio_dev); + st->spi = spi; + + ret = ad7292_spi_reg_read(st, AD7292_REG_VENDOR_ID); + if (ret != ADI_VENDOR_ID) { + dev_err(&spi->dev, "Wrong vendor id 0x%x\n", ret); + return -EINVAL; + } + + spi_set_drvdata(spi, indio_dev); + + st->reg = devm_regulator_get_optional(&spi->dev, "vref"); + if (!IS_ERR(st->reg)) { + ret = regulator_enable(st->reg); + if (ret) { + dev_err(&spi->dev, + "Failed to enable external vref supply\n"); + return ret; + } + + ret = devm_add_action_or_reset(&spi->dev, + ad7292_regulator_disable, st); + if (ret) { + regulator_disable(st->reg); + return ret; + } + |