diff options
Diffstat (limited to 'Documentation')
25 files changed, 2 insertions, 4979 deletions
diff --git a/Documentation/sound/hd-audio/models.rst b/Documentation/sound/hd-audio/models.rst index 773d2bfacc6c..1fee5a4f6660 100644 --- a/Documentation/sound/hd-audio/models.rst +++ b/Documentation/sound/hd-audio/models.rst @@ -82,6 +82,8 @@ tpt460 Lenovo Thinkpad T460/560 setup dual-codecs Lenovo laptops with dual codecs +alc700-ref + Intel reference board with ALC700 codec ALC66x/67x/892 ============== diff --git a/Documentation/sound/oss/ALS b/Documentation/sound/oss/ALS deleted file mode 100644 index bf10bed4574b..000000000000 --- a/Documentation/sound/oss/ALS +++ /dev/null @@ -1,66 +0,0 @@ -ALS-007/ALS-100/ALS-200 based sound cards -========================================= - -Support for sound cards based around the Avance Logic -ALS-007/ALS-100/ALS-200 chip is included. These chips are a single -chip PnP sound solution which is mostly hardware compatible with the -Sound Blaster 16 card, with most differences occurring in the use of -the mixer registers. For this reason the ALS code is integrated -as part of the Sound Blaster 16 driver (adding only 800 bytes to the -SB16 driver). - -To use an ALS sound card under Linux, enable the following options as -modules in the sound configuration section of the kernel config: - - 100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support - - FM synthesizer (YM3812/OPL-3) support - - standalone MPU401 support may be required for some cards; for the - ALS-007, when using isapnptools, it is required -Since the ALS-007/100/200 are PnP cards, ISAPnP support should probably be -compiled in. If kernel level PnP support is not included, isapnptools will -be required to configure the card before the sound modules are loaded. - -When using kernel level ISAPnP, the kernel should correctly identify and -configure all resources required by the card when the "sb" module is -inserted. Note that the ALS-007 does not have a 16 bit DMA channel and that -the MPU401 interface on this card uses a different interrupt to the audio -section. This should all be correctly configured by the kernel; if problems -with the MPU401 interface surface, try using the standalone MPU401 module, -passing "0" as the "sb" module's "mpu_io" module parameter to prevent the -soundblaster driver attempting to register the MPU401 itself. The onboard -synth device can be accessed using the "opl3" module. - -If isapnptools is used to wake up the sound card (as in 2.2.x), the settings -of the card's resources should be passed to the kernel modules ("sb", "opl3" -and "mpu401") using the module parameters. When configuring an ALS-007, be -sure to specify different IRQs for the audio and MPU401 sections - this card -requires they be different. For "sb", "io", "irq" and "dma" should be set -to the same values used to configure the audio section of the card with -isapnp. "dma16" should be explicitly set to "-1" for an ALS-007 since this -card does not have a 16 bit dma channel; if not specified the kernel will -default to using channel 5 anyway which will cause audio not to work. -"mpu_io" should be set to 0. The "io" parameter of the "opl3" module should -also agree with the setting used by isapnp. To get the MPU401 interface -working on an ALS-007 card, the "mpu401" module will be required since this -card uses separate IRQs for the audio and MPU401 sections and there is no -parameter available to pass a different IRQ to the "sb" driver (whose -inbuilt MPU401 driver would otherwise be fine). Insert the mpu401 module -passing appropriate values using the "io" and "irq" parameters. - -The resulting sound driver will provide the following capabilities: - - 8 and 16 bit audio playback - - 8 and 16 bit audio recording - - Software selection of record source (line in, CD, FM, mic, master) - - Record and playback of midi data via the external MPU-401 - - Playback of midi data using inbuilt FM synthesizer - - Control of the ALS-007 mixer via any OSS-compatible mixer programs. - Controls available are Master (L&R), Line in (L&R), CD (L&R), - DSP/PCM/audio out (L&R), FM (L&R) and Mic in (mono). - -Jonathan Woithe -jwoithe@just42.net -30 March 1998 - -Modified 2000-02-26 by Dave Forrest, drf5n@virginia.edu to add ALS100/ALS200 -Modified 2000-04-10 by Paul Laufer, pelaufer@csupomona.edu to add ISAPnP info. -Modified 2000-11-19 by Jonathan Woithe, jwoithe@just42.net - - updated information for kernel 2.4.x. diff --git a/Documentation/sound/oss/AudioExcelDSP16 b/Documentation/sound/oss/AudioExcelDSP16 deleted file mode 100644 index ea8549faede9..000000000000 --- a/Documentation/sound/oss/AudioExcelDSP16 +++ /dev/null @@ -1,101 +0,0 @@ -Driver ------- - -Information about Audio Excel DSP 16 driver can be found in the source -file aedsp16.c -Please, read the head of the source before using it. It contain useful -information. - -Configuration -------------- - -The Audio Excel configuration, is now done with the standard Linux setup. -You have to configure the sound card (Sound Blaster or Microsoft Sound System) -and, if you want it, the Roland MPU-401 (do not use the Sound Blaster MPU-401, -SB-MPU401) in the main driver menu. Activate the lowlevel drivers then select -the Audio Excel hardware that you want to initialize. Check the IRQ/DMA/MIRQ -of the Audio Excel initialization: it must be the same as the SBPRO (or MSS) -setup. If the parameters are different, correct it. -I you own a Gallant's audio card based on SC-6600, activate the SC-6600 support. -If you want to change the configuration of the sound board, be sure to -check off all the configuration items before re-configure it. - -Module parameters ------------------ -To use this driver as a module, you must configure some module parameters, to -set up I/O addresses, IRQ lines and DMA channels. Some parameters are -mandatory while some others are optional. Here a list of parameters you can -use with this module: - -Name Description -==== =========== -MANDATORY -io I/O base address (0x220 or 0x240) -irq irq line (5, 7, 9, 10 or 11) -dma dma channel (0, 1 or 3) - -OPTIONAL -mss_base I/O base address for activate MSS mode (default SBPRO) - (0x530 or 0xE80) -mpu_base I/O base address for activate MPU-401 mode - (0x300, 0x310, 0x320 or 0x330) -mpu_irq MPU-401 irq line (5, 7, 9, 10 or 0) - -A configuration file in /etc/modprobe.d/ directory will have lines like this: - -options opl3 io=0x388 -options ad1848 io=0x530 irq=11 dma=3 -options aedsp16 io=0x220 irq=11 dma=3 mss_base=0x530 - -Where the aedsp16 options are the options for this driver while opl3 and -ad1848 are the corresponding options for the MSS and OPL3 modules. - -Loading MSS and OPL3 needs to pre load the aedsp16 module to set up correctly -the sound card. Installation dependencies must be written in configuration -files under /etc/modprobe.d/ directory: - -softdep ad1848 pre: aedsp16 -softdep opl3 pre: aedsp16 - -Then you must load the sound modules stack in this order: -sound -> aedsp16 -> [ ad1848, opl3 ] - -With the above configuration, loading ad1848 or opl3 modules, will -automatically load all the sound stack. - -Sound cards supported ---------------------- -This driver supports the SC-6000 and SC-6600 based Gallant's sound card. -It don't support the Audio Excel DSP 16 III (try the SC-6600 code). -I'm working on the III version of the card: if someone have useful -information about it, please let me know. -For all the non-supported audio cards, you have to boot MS-DOS (or WIN95) -activating the audio card with the MS-DOS device driver, then you have to -<ctrl>-<alt>-<del> and boot Linux. -Follow these steps: - -1) Compile Linux kernel with standard sound driver, using the emulation - you want, with the parameters of your audio card, - e.g. Microsoft Sound System irq10 dma3 -2) Install your new kernel as the default boot kernel. -3) Boot MS-DOS and configure the audio card with the boot time device - driver, for MSS irq10 dma3 in our example. -4) <ctrl>-<alt>-<del> and boot Linux. This will maintain the DOS configuration - and will boot the new kernel with sound driver. The sound driver will find - the audio card and will recognize and attach it. - -Reports on User successes -------------------------- - -> Date: Mon, 29 Jul 1996 08:35:40 +0100 -> From: Mr S J Greenaway <sjg95@unixfe.rl.ac.uk> -> To: riccardo@cdc8g5.cdc.polimi.it (Riccardo Facchetti) -> Subject: Re: Audio Excel DSP 16 initialization code -> -> Just to let you know got my Audio Excel (emulating a MSS) working -> with my original SB16, thanks for the driver! - - -Last revised: 20 August 1998 -Riccardo Facchetti -fizban@tin.it diff --git a/Documentation/sound/oss/CMI8330 b/Documentation/sound/oss/CMI8330 deleted file mode 100644 index 8a5fd1611c6f..000000000000 --- a/Documentation/sound/oss/CMI8330 +++ /dev/null @@ -1,152 +0,0 @@ -Documentation for CMI 8330 (SoundPRO) -------------------------------------- -Alessandro Zummo <azummo@ita.flashnet.it> - -( Be sure to read Documentation/sound/oss/SoundPro too ) - - -This adapter is now directly supported by the sb driver. - - The only thing you have to do is to compile the kernel sound -support as a module and to enable kernel ISAPnP support, -as shown below. - - -CONFIG_SOUND=m -CONFIG_SOUND_SB=m - -CONFIG_PNP=y -CONFIG_ISAPNP=y - - -and optionally: - - -CONFIG_SOUND_MPU401=m - - for MPU401 support. - - -(I suggest you to use "make menuconfig" or "make xconfig" - for a more comfortable configuration editing) - - - -Then you can do - - modprobe sb - -and everything will be (hopefully) configured. - -You should get something similar in syslog: - -sb: CMI8330 detected. -sb: CMI8330 sb base located at 0x220 -sb: CMI8330 mpu base located at 0x330 -sb: CMI8330 mail reports to Alessandro Zummo <azummo@ita.flashnet.it> -sb: ISAPnP reports CMI 8330 SoundPRO at i/o 0x220, irq 7, dma 1,5 - - - - -The old documentation file follows for reference -purposes. - - -How to enable CMI 8330 (SOUNDPRO) soundchip on Linux ------------------------------------------- -Stefan Laudat <Stefan.Laudat@asit.ro> - -[Note: The CMI 8338 is unrelated and is supported by cmpci.o] - - - In order to use CMI8330 under Linux you just have to use a proper isapnp.conf, a good isapnp and a little bit of patience. I use isapnp 1.17, but -you may get a better one I guess at http://www.roestock.demon.co.uk/isapnptools/. - - Of course you will have to compile kernel sound support as module, as shown below: - -CONFIG_SOUND=m -CONFIG_SOUND_OSS=m -CONFIG_SOUND_SB=m -CONFIG_SOUND_ADLIB=m -CONFIG_SOUND_MPU401=m -# Mikro$chaft sound system (kinda useful here ;)) -CONFIG_SOUND_MSS=m - - The /etc/isapnp.conf file will be: - -<snip below> - - -(READPORT 0x0203) -(ISOLATE PRESERVE) -(IDENTIFY *) -(VERBOSITY 2) -(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING -(VERIFYLD N) - - -# WSS - -(CONFIGURE CMI0001/16777472 (LD 0 -(IO 0 (SIZE 8) (BASE 0x0530)) -(IO 1 (SIZE 8) (BASE 0x0388)) -(INT 0 (IRQ 7 (MODE +E))) -(DMA 0 (CHANNEL 0)) -(NAME "CMI0001/16777472[0]{CMI8330/C3D Audio Adapter}") -(ACT Y) -)) - -# MPU - -(CONFIGURE CMI0001/16777472 (LD 1 -(IO 0 (SIZE 2) (BASE 0x0330)) -(INT 0 (IRQ 11 (MODE +E))) -(NAME "CMI0001/16777472[1]{CMI8330/C3D Audio Adapter}") -(ACT Y) -)) - -# Joystick - -(CONFIGURE CMI0001/16777472 (LD 2 -(IO 0 (SIZE 8) (BASE 0x0200)) -(NAME "CMI0001/16777472[2]{CMI8330/C3D Audio Adapter}") -(ACT Y) -)) - -# SoundBlaster - -(CONFIGURE CMI0001/16777472 (LD 3 -(IO 0 (SIZE 16) (BASE 0x0220)) -(INT 0 (IRQ 5 (MODE +E))) -(DMA 0 (CHANNEL 1)) -(DMA 1 (CHANNEL 5)) -(NAME "CMI0001/16777472[3]{CMI8330/C3D Audio Adapter}") -(ACT Y) -)) - - -(WAITFORKEY) - -<end of snip> - - The module sequence is trivial: - -/sbin/insmod soundcore -/sbin/insmod sound -/sbin/insmod uart401 -# insert this first -/sbin/insmod ad1848 io=0x530 irq=7 dma=0 soundpro=1 -# The sb module is an alternative to the ad1848 (Microsoft Sound System) -# Anyhow, this is full duplex and has MIDI -/sbin/insmod sb io=0x220 dma=1 dma16=5 irq=5 mpu_io=0x330 - - - -Alma Chao <elysian@ethereal.torsion.org> suggests the following in -a /etc/modprobe.d/*conf file: - -alias sound ad1848 -alias synth0 opl3 -options ad1848 io=0x530 irq=7 dma=0 soundpro=1 -options opl3 io=0x388 diff --git a/Documentation/sound/oss/ESS b/Documentation/sound/oss/ESS deleted file mode 100644 index bba93b4d2def..000000000000 --- a/Documentation/sound/oss/ESS +++ /dev/null @@ -1,34 +0,0 @@ -Documentation for the ESS AudioDrive chips - -In 2.4 kernels the SoundBlaster driver not only tries to detect an ESS chip, it -tries to detect the type of ESS chip too. The correct detection of the chip -doesn't always succeed however, so unless you use the kernel isapnp facilities -(and you chip is pnp capable) the default behaviour is 2.0 behaviour which -means: only detect ES688 and ES1688. - -All ESS chips now have a recording level setting. This is a need-to-have for -people who want to use their ESS for recording sound. - -Every chip that's detected as a later-than-es1688 chip has a 6 bits logarithmic -master volume control. - -Every chip that's detected as a ES1887 now has Full Duplex support. Made a -little testprogram that shows that is works, haven't seen a real program that -needs this however. - -For ESS chips an additional parameter "esstype" can be specified. This controls -the (auto) detection of the ESS chips. It can have 3 kinds of values: - --1 Act like 2.0 kernels: only detect ES688 or ES1688. -0 Try to auto-detect the chip (may fail for ES1688) -688 The chip will be treated as ES688 -1688 ,, ,, ,, ,, ,, ,, ES1688 -1868 ,, ,, ,, ,, ,, ,, ES1868 -1869 ,, ,, ,, ,, ,, ,, ES1869 -1788 ,, ,, ,, ,, ,, ,, ES1788 -1887 ,, ,, ,, ,, ,, ,, ES1887 -1888 ,, ,, ,, ,, ,, ,, ES1888 - -Because Full Duplex is supported for ES1887 you can specify a second DMA -channel by specifying module parameter dma16. It can be one of: 0, 1, 3 or 5. - diff --git a/Documentation/sound/oss/ESS1868 b/Documentation/sound/oss/ESS1868 deleted file mode 100644 index 55e922f21bc0..000000000000 --- a/Documentation/sound/oss/ESS1868 +++ /dev/null @@ -1,55 +0,0 @@ -Documentation for the ESS1868F AudioDrive PnP sound card - -The ESS1868 sound card is a PnP ESS1688-compatible 16-bit sound card. - -It should be automatically detected by the Linux Kernel isapnp support when you -load the sb.o module. Otherwise you should take care of: - - * The ESS1868 does not allow use of a 16-bit DMA, thus DMA 0, 1, 2, and 3 - may only be used. - - * isapnptools version 1.14 does work with ESS1868. Earlier versions might - not. - - * Sound support MUST be compiled as MODULES, not statically linked - into the kernel. - - -NOTE: this is only needed when not using the kernel isapnp support! - -For configuring the sound card's I/O addresses, IRQ and DMA, here is a -sample copy of the isapnp.conf directives regarding the ESS1868: - -(CONFIGURE ESS1868/-1 (LD 1 -(IO 0 (BASE 0x0220)) -(IO 1 (BASE 0x0388)) -(IO 2 (BASE 0x0330)) -(DMA 0 (CHANNEL 1)) -(INT 0 (IRQ 5 (MODE +E))) -(ACT Y) -)) - -(for a full working isapnp.conf file, remember the -(ISOLATE) -(IDENTIFY *) -at the beginning and the -(WAITFORKEY) -at the end.) - -In this setup, the main card I/O is 0x0220, FM synthesizer is 0x0388, and -the MPU-401 MIDI port is located at 0x0330. IRQ is IRQ 5, DMA is channel 1. - -After configuring the sound card via isapnp, to use the card you must load -the sound modules with the proper I/O information. Here is my setup: - -# ESS1868F AudioDrive initialization - -/sbin/modprobe sound -/sbin/insmod uart401 -/sbin/insmod sb io=0x220 irq=5 dma=1 dma16=-1 -/sbin/insmod mpu401 io=0x330 -/sbin/insmod opl3 io=0x388 -/sbin/insmod v_midi - -opl3 is the FM synthesizer -/sbin/insmod opl3 io=0x388 diff --git a/Documentation/sound/oss/Introduction b/Documentation/sound/oss/Introduction deleted file mode 100644 index 42da2d8fa372..000000000000 --- a/Documentation/sound/oss/Introduction +++ /dev/null @@ -1,459 +0,0 @@ -Introduction Notes on Modular Sound Drivers and Soundcore -Wade Hampton -2/14/2001 - -Purpose: -======== -This document provides some general notes on the modular -sound drivers and their configuration, along with the -support modules sound.o and soundcore.o. - -Note, some of this probably should be added to the Sound-HOWTO! - -Note, soundlow.o was present with 2.2 kernels but is not -required for 2.4.x kernels. References have been removed -to this. - - -Copying: -======== -none - - -History: -======== -0.1.0 11/20/1998 First version, draft -1.0.0 11/1998 Alan Cox changes, incorporation in 2.2.0 - as Documentation/sound/oss/Introduction -1.1.0 6/30/1999 Second version, added notes on making the drivers, - added info on multiple sound cards of similar types,] - added more diagnostics info, added info about esd. - added info on OSS and ALSA. -1.1.1 19991031 Added notes on sound-slot- and sound-service. - (Alan Cox) -1.1.2 20000920 Modified for Kernel 2.4 (Christoph Hellwig) -1.1.3 20010214 Minor notes and corrections (Wade Hampton) - Added examples of sound-slot-0, etc. - - -Modular Sound Drivers: -====================== - -Thanks to the GREAT work by Alan Cox (alan@lxorguk.ukuu.org.uk), - -[And Oleg Drokin, Thomas Sailer, Andrew Veliath and more than a few - others - not to mention Hannu's original code being designed well - enough to cope with that kind of chopping up](Alan) - -the standard Linux kernels support a modular sound driver. From -Alan's comments in linux/drivers/sound/README.FIRST: - - The modular sound driver patches were funded by Red Hat Software - (www.redhat.com). The sound driver here is thus a modified version of - Hannu's code. Please bear that in mind when considering the appropriate - forums for bug reporting. - -The modular sound drivers may be loaded via insmod or modprobe. -To support all the various sound modules, there are two general -support modules that must be loaded first: - - soundcore.o: Top level handler for the sound system, provides - a set of functions for registration of devices - by type. - - sound.o: Common sound functions required by all modules. - -For the specific sound modules (e.g., sb.o for the Soundblaster), -read the documentation on that module to determine what options -are available, for example IRQ, address, DMA. - -Warning, the options for different cards sometime use different names -for the same or a similar feature (dma1= versus dma16=). As a last -resort, inspect the code (search for module_param). - -Notes: - -1. There is a new OpenSource sound driver called ALSA which is - currently under development: http://www.alsa-project.org/ - The ALSA drivers support some newer hardware that may not - be supported by this sound driver and also provide some - additional features. - -2. The commercial OSS driver may be obtained from the site: - http://www.opensound.com. This may be used for cards that - are unsupported by the kernel driver, or may be used - by other operating systems. - -3. The enlightenment sound daemon may be used for playing - multiple sounds at the same time via a single card, eliminating - some of the requirements for multiple sound card systems. For - more information, see: http://www.tux.org/~ricdude/EsounD.html - The "esd" program may be used with the real-player and mpeg - players like mpg123 and x11amp. The newer real-player - and some games even include built-in support for ESD! - - -Building the Modules: -===================== - -This document does not provide full details on building the -kernel, etc. The notes below apply only to making the kernel -sound modules. If this conflicts with the kernel's README, -the README takes precedence. - -1. To make the kernel sound modules, cd to your /usr/src/linux - directory (typically) and type make config, make menuconfig, - or make xconfig (to start the command line, dialog, or x-based - configuration tool). - -2. Select the Sound option and a dialog will be displayed. - -3. Select M (module) for "Sound card support". - -4. Select your sound driver(s) as a module. For ProAudio, Sound - Blaster, etc., select M (module) for OSS sound modules. - [thanks to Marvin Stodolsky <stodolsk@erols.com>]A - -5. Make the kernel (e.g., make bzImage), and install the kernel. - -6. Make the modules and install them (make modules; make modules_install). - -Note, for 2.5.x kernels, make sure you have the newer module-init-tools -installed or modules will not be loaded properly. 2.5.x requires an -updated module-init-tools. - - -Plug and Play (PnP: -=================== - -If the sound card is an ISA PnP card, isapnp may be used -to configure the card. See the file isapnp.txt in the -directory one level up (e.g., /usr/src/linux/Documentation). - -Also the 2.4.x kernels provide PnP capabilities, see the -file NEWS in this directory. - -PCI sound cards are highly recommended, as they are far -easier to configure and from what I have read, they use -less resources and are more CPU efficient. - - -INSMOD: -======= - -If loading via insmod, the common modules must be loaded in the -order below BEFORE loading the other sound modules. The card-specific -modules may then be loaded (most require parameters). For example, -I use the following via a shell script to load my SoundBlaster: - -SB_BASE=0x240 -SB_IRQ=9 -SB_DMA=3 -SB_DMA2=5 -SB_MPU=0x300 -# -echo Starting sound -/sbin/insmod soundcore -/sbin/insmod sound -# -echo Starting sound blaster.... -/sbin/insmod uart401 -/sbin/insmod sb io=$SB_BASE irq=$SB_IRQ dma=$SB_DMA dma16=$SB_DMA2 mpu_io=$SB_MP - -When using sound as a module, I typically put these commands -in a file such as /root/soundon.sh. - - -MODPROBE: -========= - -If loading via modprobe, these common files are automatically loaded when -requested by modprobe. For example, my /etc/modprobe.d/oss.conf contains: - -alias sound sb -options sb io=0x240 irq=9 dma=3 dma16=5 mpu_io=0x300 - -All you need to do to load the module is: - - /sbin/modprobe sb - - -Sound Status: -============= - -The status of sound may be read/checked by: - cat (anyfile).au >/dev/audio - -[WWH: This may not work properly for SoundBlaster PCI 128 cards -such as the es1370/1 (see the es1370/1 files in this directory) -as they do not automatically support uLaw on /dev/audio.] - -The status of the modules and which modules depend on -which other modules may be checked by: - /sbin/lsmod - -/sbin/lsmod should show something like the following: - sb 26280 0 - uart401 5640 0 [sb] - sound 57112 0 [sb uart401] - soundcore 1968 8 [sb sound] - - -Removing Sound: -=============== - -Sound may be removed by using /sbin/rmmod in the reverse order -in which you load the modules. Note, if a program has a sound device -open (e.g., xmixer), that module (and the modules on which it -depends) may not be unloaded. - -For example, I use the following to remove my Soundblaster (rmmod -in the reverse order in which I loaded the modules): - -/sbin/rmmod sb -/sbin/rmmod uart401 -/sbin/rmmod sound -/sbin/rmmod soundcore - -When using sound as a module, I typically put these commands -in a script such as /root/soundoff.sh. - - -Removing Sound for use with OSS: -================================ - -If you get really stuck or have a card that the kernel modules -will not support, you can get a commercial sound driver from -http://www.opensound.com. Before loading the commercial sound -driver, you should do the following: - -1. remove sound modules (detailed above) -2. remove the sound modules from /etc/modprobe.d/*.conf -3. move the sound modules from /lib/modules/<kernel>/misc - (for example, I make a /lib/modules/<kernel>/misc/tmp - directory and copy the sound module files to that - directory). - - -Multiple Sound Cards: -===================== - -The sound drivers will support multiple sound cards and there -are some great applications like multitrack that support them. -Typically, you need two sound cards of different types. Note, this -uses more precious interrupts and DMA channels and sometimes -can be a configuration nightmare. I have heard reports of 3-4 -sound cards (typically I only use 2). You can sometimes use -multiple PCI sound cards of the same type. - -On my machine I have two sound cards (cs4232 and Soundblaster Vibra -16). By loading sound as modules, I can control which is the first -sound device (/dev/dsp, /dev/audio, /dev/mixer) and which is -the second. Normally, the cs4232 (Dell sound on the motherboard) -would be the first sound device, but I prefer the Soundblaster. -All you have to do is to load the one you want as /dev/dsp -first (in my case "sb") and then load the other one -(in my case "cs4232"). - -If you have two cards of the same type that are jumpered -cards or different PnP revisions, you may load the same -module twice. For example, I have a SoundBlaster vibra 16 -and an older SoundBlaster 16 (jumpers). To load the module -twice, you need to do the following: - -1. Copy the sound modules to a new name. For example - sb.o could be copied (or symlinked) to sb1.o for the - second SoundBlaster. - -2. Make a second entry in /etc/modprobe.d/*conf, for example, - sound1 or sb1. This second entry should refer to the - new module names for example sb1, and should include - the I/O, etc. for the second sound card. - -3. Update your soundon.sh script, etc. - -Warning: I have never been able to get two PnP sound cards of the -same type to load at the same time. I have tried this several times -with the Soundblaster Vibra 16 cards. OSS has indicated that this -is a PnP problem.... If anyone has any luck doing this, please -send me an E-MAIL. PCI sound cards should not have this problem.a -Since this was originally release, I have received a couple of -mails from people who have accomplished this! - -NOTE: In Linux 2.4 the Sound Blaster driver (and only this one yet) -supports multiple cards with one module by default. -Read the file 'Soundblaster' in this directory for details. - - -Sound Problems: -=============== - -First RTFM (including the troubleshooting section -in the Sound-HOWTO). - -1) If you are having problems loading the modules (for - example, if you get device conflict errors) try the - following: - - A) If you have Win95 or NT on the same computer, - write down what addresses, IRQ, and DMA channels - those were using for the same hardware. You probably - can use these addresses, IRQs, and DMA channels. - You should really do this BEFORE attempting to get - sound working! - - B) Check (cat) /proc/interrupts, /proc/ioports, - and /proc/dma. Are you trying to use an address, - IRQ or DMA port that another device is using? - - C) Check (cat) /proc/isapnp - - D) Inspect your /var/log/messages file. Often that will - indicate what IRQ or IO port could not be obtained. - - E) Try another port or IRQ. Note this may involve - using the PnP tools to move the sound card to - another location. Sometimes this is the only way - and it is more or less trial and error. - -2) If you get motor-boating (the same sound or part of a - sound clip repeated), you probably have either an IRQ - or DMA conflict. Move the card to another IRQ or DMA - port. This has happened to me when playing long files - when I had an IRQ conflict. - -3. If you get dropouts or pauses when playing high sample - rate files such as using mpg123 or x11amp/xmms, you may - have too slow of a CPU and may have to use the options to - play the files at 1/2 speed. For example, you may use - the -2 or -4 option on mpg123. You may also get this - when trying to play mpeg files stored on a CD-ROM - (my Toshiba T8000 PII/366 sometimes has this problem). - -4. If you get "cannot access device" errors, your /dev/dsp - files, etc. may be set to owner root, mode 600. You - may have to use the command: - chmod 666 /dev/dsp /dev/mixer /dev/audio - -5. If you get "device busy" errors, another program has the - sound device open. For example, if using the Enlightenment - sound daemon "esd", the "esd" program has the sound device. - If using "esd", please RTFM the docs on ESD. For example, - esddsp <program> may be used to play files via a non-esd - aware program. - -6) Ask for help on the sound list or send E-MAIL to the - sound driver author/maintainer. - -7) Turn on debug in drivers/sound/sound_config.h (DEB, DDB, MDB). - -8) If the system reports insufficient DMA memory then you may want to - load sound with the "dmabufs=1" option. Or in /etc/conf.modules add - - preinstall sound dmabufs=1 - - This makes the sound system allocate its buffers and hang onto them. - - You may also set persistent DMA when building a 2.4.x kernel. - - -Configuring Sound: -================== - -There are several ways of configuring your sound: - -1) On the kernel command line (when using the sound driver(s) - compiled in the kernel). Check the driver source and - documentation for details. - -2) On the command line when using insmod or in a bash script - using command line calls to load sound. - -3) In /etc/modprobe.d/*conf when using modprobe. - -4) Via Red Hat's GPL'd /usr/sbin/sndconfig program (text based). - -5) Via the OSS soundconf program (with the commercial version - of the OSS driver. - -6) By just loading the module and let isapnp do everything relevant - for you. This works only with a few drivers yet and - of course - - only with isapnp hardware. - -And I am sure, several other ways. - -Anyone want to write a linuxconf module for configuring sound? - - -Module Loading: -=============== - -When a sound card is first referenced and sound is modular, the sound system -will ask for the sound devices to be loaded. Initially it requests that -the driver for the sound system is loaded. It then will ask for -sound-slot-0, where 0 is the first sound card. (sound-slot-1 the second and -so on). Thus you can do - -alias sound-slot-0 sb - -To load a soundblaster at this point. If the slot loading does not provide -the desired device - for example a soundblaster does not directly provide -a midi synth in all cases then it will request "sound-service-0-n" where n -is - - 0 Mixer - - 2 MIDI - - 3, 4 DSP audio - - -For example, |