diff options
Diffstat (limited to 'Documentation')
-rw-r--r-- | Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt | 98 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/iio/adc/renesas,rcar-gyroadc.yaml | 143 |
2 files changed, 143 insertions, 98 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt deleted file mode 100644 index df5b9f2ad8d8..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt +++ /dev/null @@ -1,98 +0,0 @@ -* Renesas R-Car GyroADC device driver - -The GyroADC block is a reduced SPI block with up to 8 chipselect lines, -which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs -are sampled by the GyroADC block in a round-robin fashion and the result -presented in the GyroADC registers. - -Required properties: -- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc". - The <soc-specific> should be one of: - renesas,r8a7791-gyroadc - for the GyroADC block present - in r8a7791 SoC - renesas,r8a7792-gyroadc - for the GyroADC with interrupt - block present in r8a7792 SoC -- reg: Address and length of the register set for the device -- clocks: References to all the clocks specified in the clock-names - property as specified in - Documentation/devicetree/bindings/clock/clock-bindings.txt. -- clock-names: Shall contain "fck". The "fck" is the GyroADC block clock. -- power-domains: Must contain a reference to the PM domain, if available. -- #address-cells: Should be <1> (setting for the subnodes) for all ADCs - except for "fujitsu,mb88101a". Should be <0> (setting for - only subnode) for "fujitsu,mb88101a". -- #size-cells: Should be <0> (setting for the subnodes) - -Sub-nodes: -You must define subnode(s) which select the connected ADC type and reference -voltage for the GyroADC channels. - -Required properties for subnodes: -- compatible: Should be either of: - "fujitsu,mb88101a" - - Fujitsu MB88101A compatible mode, - 12bit sampling, up to 4 channels can be sampled in - round-robin fashion. One Fujitsu chip supplies four - GyroADC channels with data as it contains four ADCs - on the chip and thus for 4-channel operation, single - MB88101A is required. The Cx chipselect lines of the - MB88101A connect directly to two CHS lines of the - GyroADC, no demuxer is required. The data out line - of each MB88101A connects to a shared input pin of - the GyroADC. - "ti,adcs7476" or "ti,adc121" or "adi,ad7476" - - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, - 15bit sampling, up to 8 channels can be sampled in - round-robin fashion. One TI/ADI chip supplies single - ADC channel with data, thus for 8-channel operation, - 8 chips are required. A 3:8 chipselect demuxer is - required to connect the nCS line of the TI/ADI chips - to the GyroADC, while MISO line of each TI/ADI ADC - connects to a shared input pin of the GyroADC. - "maxim,max1162" or "maxim,max11100" - - Maxim MAX1162 / Maxim MAX11100 compatible mode, - 16bit sampling, up to 8 channels can be sampled in - round-robin fashion. One Maxim chip supplies single - ADC channel with data, thus for 8-channel operation, - 8 chips are required. A 3:8 chipselect demuxer is - required to connect the nCS line of the MAX chips - to the GyroADC, while MISO line of each Maxim ADC - connects to a shared input pin of the GyroADC. -- reg: Should be the number of the analog input. Should be present - for all ADCs except "fujitsu,mb88101a". -- vref-supply: Reference to the channel reference voltage regulator. - -Example: - vref_max1162: regulator-vref-max1162 { - compatible = "regulator-fixed"; - - regulator-name = "MAX1162 Vref"; - regulator-min-microvolt = <4096000>; - regulator-max-microvolt = <4096000>; - }; - - adc@e6e54000 { - compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; - reg = <0 0xe6e54000 0 64>; - clocks = <&mstp9_clks R8A7791_CLK_GYROADC>; - clock-names = "fck"; - power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; - - pinctrl-0 = <&adc_pins>; - pinctrl-names = "default"; - - #address-cells = <1>; - #size-cells = <0>; - - adc@0 { - reg = <0>; - compatible = "maxim,max1162"; - vref-supply = <&vref_max1162>; - }; - - adc@1 { - reg = <1>; - compatible = "maxim,max1162"; - vref-supply = <&vref_max1162>; - }; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,rcar-gyroadc.yaml b/Documentation/devicetree/bindings/iio/adc/renesas,rcar-gyroadc.yaml new file mode 100644 index 000000000000..c115e2e99bd9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/renesas,rcar-gyroadc.yaml @@ -0,0 +1,143 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/renesas,rcar-gyroadc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car GyroADC + +maintainers: + - Marek Vasut <marek.vasut+renesas@gmail.com> + +description: | + The GyroADC block is a reduced SPI block with up to 8 chipselect lines, + which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs + are sampled by the GyroADC block in a round-robin fashion and the result + presented in the GyroADC registers. + The ADC bindings should match with that of the devices connected to a + full featured SPI bus. + +properties: + compatible: + items: + - enum: + - renesas,r8a7791-gyroadc + - renesas,r8a7792-gyroadc + - const: renesas,rcar-gyroadc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: fck + + power-domains: true + + resets: true + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - "#address-cells" + - "#size-cells" + +patternProperties: + "@[0-7]$": + type: object + properties: + compatible: + description: | + fujitsu,mb88101a + - Fujitsu MB88101A compatible mode, + 12bit sampling, up to 4 channels can be sampled in round-robin + fashion. One Fujitsu chip supplies four GyroADC channels with + data as it contains four ADCs on the chip and thus for 4-channel + operation, single MB88101A is required. The Cx chipselect lines + of the MB88101A connect directly to two CHS lines of the GyroADC, + no demuxer is required. The data out line of each MB88101A + connects to a shared input pin of the GyroADC. + ti,adcs7476 or ti,adc121 or adi,ad7476 + - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, 15bit + sampling, up to 8 channels can be sampled in round-robin + fashion. One TI/ADI chip supplies single ADC channel with data, + thus for 8-channel operation, 8 chips are required. + A 3:8 chipselect demuxer is required to connect the nCS line + of the TI/ADI chips to the GyroADC, while MISO line of each + TI/ADI ADC connects to a shared input pin of the GyroADC. + maxim,max1162 or maxim,max11100 + - Maxim MAX1162 / Maxim MAX11100 compatible mode, 16bit sampling, + up to 8 channels can be sampled in round-robin fashion. One + Maxim chip supplies single ADC channel with data, thus for + 8-channel operation, 8 chips are required. + A 3:8 chipselect demuxer is required to connect the nCS line + of the MAX chips to the GyroADC, while MISO line of each Maxim + ADC connects to a shared input pin of the GyroADC. + enum: + - adi,7476 + - fujitsu,mb88101a + - maxim,max1162 + - maxim,max11100 + - ti,adcs7476 + - ti,adc121 + + reg: + minimum: 0 + maximum: 7 + + vref-supply: true + + additionalProperties: false + + required: + - compatible + - reg + - vref-supply + +examples: + - | + #include <dt-bindings/clock/r8a7791-clock.h> + #include <dt-bindings/power/r8a7791-sysc.h> + soc { + #address-cells = <2>; + #size-cells = <2>; + + adc@e6e54000 { + compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; + reg = <0 0xe6e54000 0 64>; + clocks = <&mstp9_clks R8A7791_CLK_GYROADC>; + clock-names = "fck"; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + + pinctrl-0 = <&adc_pins>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + reg = <0>; + compatible = "maxim,max1162"; + vref-supply = <&vref_max1162>; + }; + + adc@1 { + reg = <1>; + compatible = "maxim,max1162"; + vref-supply = <&vref_max1162>; + }; + }; + }; +... |