diff options
Diffstat (limited to 'Documentation')
124 files changed, 190 insertions, 190 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-css b/Documentation/ABI/testing/sysfs-bus-css index b585ec258a08..2979c40c10e9 100644 --- a/Documentation/ABI/testing/sysfs-bus-css +++ b/Documentation/ABI/testing/sysfs-bus-css @@ -29,7 +29,7 @@ Contact: Cornelia Huck <cornelia.huck@de.ibm.com> linux-s390@vger.kernel.org Description: Contains the PIM/PAM/POM values, as reported by the channel subsystem when last queried by the common I/O - layer (this implies that this attribute is not neccessarily + layer (this implies that this attribute is not necessarily in sync with the values current in the channel subsystem). Note: This is an I/O-subchannel specific attribute. Users: s390-tools, HAL diff --git a/Documentation/ABI/testing/sysfs-class-led b/Documentation/ABI/testing/sysfs-class-led index edff6630c805..3646ec85d513 100644 --- a/Documentation/ABI/testing/sysfs-class-led +++ b/Documentation/ABI/testing/sysfs-class-led @@ -33,5 +33,5 @@ Contact: Richard Purdie <rpurdie@rpsys.net> Description: Invert the LED on/off state. This parameter is specific to gpio and backlight triggers. In case of the backlight trigger, - it is usefull when driving a LED which is intended to indicate + it is useful when driving a LED which is intended to indicate a device in a standby like state. diff --git a/Documentation/DocBook/dvb/dvbproperty.xml b/Documentation/DocBook/dvb/dvbproperty.xml index 5f57c7ccd4ba..97f397e2fb3a 100644 --- a/Documentation/DocBook/dvb/dvbproperty.xml +++ b/Documentation/DocBook/dvb/dvbproperty.xml @@ -40,7 +40,7 @@ <para>Central frequency of the channel.</para> - <para>For ISDB-T the channels are usally transmitted with an offset of 143kHz. E.g. a + <para>For ISDB-T the channels are usually transmitted with an offset of 143kHz. E.g. a valid frequncy could be 474143 kHz. The stepping is bound to the bandwidth of the channel which is 6MHz.</para> diff --git a/Documentation/DocBook/dvb/frontend.xml b/Documentation/DocBook/dvb/frontend.xml index 78d756de5906..60c6976fb311 100644 --- a/Documentation/DocBook/dvb/frontend.xml +++ b/Documentation/DocBook/dvb/frontend.xml @@ -139,7 +139,7 @@ consistently to the DiSEqC commands as described in the DiSEqC spec.</para> <section id="frontend_sec_tone"> <title>SEC continuous tone</title> -<para>The continous 22KHz tone is usually used with non-DiSEqC capable LNBs to switch the +<para>The continuous 22KHz tone is usually used with non-DiSEqC capable LNBs to switch the high/low band of a dual-band LNB. When using DiSEqC epuipment this voltage has to be switched consistently to the DiSEqC commands as described in the DiSEqC spec.</para> diff --git a/Documentation/DocBook/kernel-locking.tmpl b/Documentation/DocBook/kernel-locking.tmpl index f66f4df18690..67e7ab41c0a6 100644 --- a/Documentation/DocBook/kernel-locking.tmpl +++ b/Documentation/DocBook/kernel-locking.tmpl @@ -1763,7 +1763,7 @@ as it would be on UP. There is a furthur optimization possible here: remember our original cache code, where there were no reference counts and the caller simply held the lock whenever using the object? This is still possible: if -you hold the lock, noone can delete the object, so you don't need to +you hold the lock, no one can delete the object, so you don't need to get and put the reference count. </para> diff --git a/Documentation/DocBook/libata.tmpl b/Documentation/DocBook/libata.tmpl index 8c5411cfeaf0..cdd1bb9aac0d 100644 --- a/Documentation/DocBook/libata.tmpl +++ b/Documentation/DocBook/libata.tmpl @@ -1032,7 +1032,7 @@ and other resources, etc. <listitem> <para> This is indicated by ICRC bit in the ERROR register and - means that corruption occurred during data transfer. Upto + means that corruption occurred during data transfer. Up to ATA/ATAPI-7, the standard specifies that this bit is only applicable to UDMA transfers but ATA/ATAPI-8 draft revision 1f says that the bit may be applicable to multiword DMA and @@ -1045,10 +1045,10 @@ and other resources, etc. <term>ABRT error during data transfer or on completion</term> <listitem> <para> - Upto ATA/ATAPI-7, the standard specifies that ABRT could be + Up to ATA/ATAPI-7, the standard specifies that ABRT could be set on ICRC errors and on cases where a device is not able to complete a command. Combined with the fact that MWDMA - and PIO transfer errors aren't allowed to use ICRC bit upto + and PIO transfer errors aren't allowed to use ICRC bit up to ATA/ATAPI-7, it seems to imply that ABRT bit alone could indicate tranfer errors. </para> @@ -1122,7 +1122,7 @@ and other reso |