summaryrefslogtreecommitdiffstats
path: root/Documentation/hwmon/smsc47m192
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/hwmon/smsc47m192')
-rw-r--r--Documentation/hwmon/smsc47m19297
1 files changed, 55 insertions, 42 deletions
diff --git a/Documentation/hwmon/smsc47m192 b/Documentation/hwmon/smsc47m192
index 6d54ecb7b3f8..a2e86ab67918 100644
--- a/Documentation/hwmon/smsc47m192
+++ b/Documentation/hwmon/smsc47m192
@@ -2,17 +2,28 @@ Kernel driver smsc47m192
========================
Supported chips:
+
* SMSC LPC47M192, LPC47M15x, LPC47M292 and LPC47M997
+
Prefix: 'smsc47m192'
+
Addresses scanned: I2C 0x2c - 0x2d
+
Datasheet: The datasheet for LPC47M192 is publicly available from
- http://www.smsc.com/
- The LPC47M15x, LPC47M292 and LPC47M997 are compatible for
- hardware monitoring.
-Author: Hartmut Rick <linux@rick.claranet.de>
- Special thanks to Jean Delvare for careful checking
- of the code and many helpful comments and suggestions.
+ http://www.smsc.com/
+
+ The LPC47M15x, LPC47M292 and LPC47M997 are compatible for
+
+ hardware monitoring.
+
+
+
+Author:
+ - Hartmut Rick <linux@rick.claranet.de>
+
+ - Special thanks to Jean Delvare for careful checking
+ of the code and many helpful comments and suggestions.
Description
@@ -52,52 +63,54 @@ Reading them more often repeats the same values.
sysfs interface
---------------
-in0_input - +2.5V voltage input
-in1_input - CPU voltage input (nominal 2.25V)
-in2_input - +3.3V voltage input
-in3_input - +5V voltage input
-in4_input - +12V voltage input (may be missing if used as VID4)
-in5_input - Vcc voltage input (nominal 3.3V)
- This is the supply voltage of the sensor chip itself.
-in6_input - +1.5V voltage input
-in7_input - +1.8V voltage input
+===================== ==========================================================
+in0_input +2.5V voltage input
+in1_input CPU voltage input (nominal 2.25V)
+in2_input +3.3V voltage input
+in3_input +5V voltage input
+in4_input +12V voltage input (may be missing if used as VID4)
+in5_input Vcc voltage input (nominal 3.3V)
+ This is the supply voltage of the sensor chip itself.
+in6_input +1.5V voltage input
+in7_input +1.8V voltage input
in[0-7]_min,
-in[0-7]_max - lower and upper alarm thresholds for in[0-7]_input reading
+in[0-7]_max lower and upper alarm thresholds for in[0-7]_input reading
- All voltages are read and written in mV.
+ All voltages are read and written in mV.
-in[0-7]_alarm - alarm flags for voltage inputs
- These files read '1' in case of alarm, '0' otherwise.
+in[0-7]_alarm alarm flags for voltage inputs
+ These files read '1' in case of alarm, '0' otherwise.
-temp1_input - chip temperature measured by on-chip diode
-temp[2-3]_input - temperature measured by external diodes (one of these would
- typically be wired to the diode inside the CPU)
+temp1_input chip temperature measured by on-chip diode
+temp[2-3]_input temperature measured by external diodes (one of these
+ would typically be wired to the diode inside the CPU)
temp[1-3]_min,
-temp[1-3]_max - lower and upper alarm thresholds for temperatures
+temp[1-3]_max lower and upper alarm thresholds for temperatures
-temp[1-3]_offset - temperature offset registers
- The chip adds the offsets stored in these registers to
- the corresponding temperature readings.
- Note that temp1 and temp2 offsets share the same register,
- they cannot both be different from zero at the same time.
- Writing a non-zero number to one of them will reset the other
- offset to zero.
+temp[1-3]_offset temperature offset registers
+ The chip adds the offsets stored in these registers to
+ the corresponding temperature readings.
+ Note that temp1 and temp2 offsets share the same register,
+ they cannot both be different from zero at the same time.
+ Writing a non-zero number to one of them will reset the other
+ offset to zero.
- All temperatures and offsets are read and written in
- units of 0.001 degC.
+ All temperatures and offsets are read and written in
+ units of 0.001 degC.
-temp[1-3]_alarm - alarm flags for temperature inputs, '1' in case of alarm,
- '0' otherwise.
-temp[2-3]_input_fault - diode fault flags for temperature inputs 2 and 3.
- A fault is detected if the two pins for the corresponding
- sensor are open or shorted, or any of the two is shorted
- to ground or Vcc. '1' indicates a diode fault.
+temp[1-3]_alarm alarm flags for temperature inputs, '1' in case of alarm,
+ '0' otherwise.
+temp[2-3]_input_fault diode fault flags for temperature inputs 2 and 3.
+ A fault is detected if the two pins for the corresponding
+ sensor are open or shorted, or any of the two is shorted
+ to ground or Vcc. '1' indicates a diode fault.
-cpu0_vid - CPU voltage as received from the CPU
+cpu0_vid CPU voltage as received from the CPU
-vrm - CPU VID standard used for decoding CPU voltage
+vrm CPU VID standard used for decoding CPU voltage
+===================== ==========================================================
- The *_min, *_max, *_offset and vrm files can be read and
- written, all others are read-only.
+The `*_min`, `*_max`, `*_offset` and `vrm` files can be read and written,
+all others are read-only.