diff options
Diffstat (limited to 'Documentation/devicetree')
4 files changed, 74 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 6e4ba816094b..03349ad5abfa 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -152,6 +152,7 @@ ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) sgx,vz89x SGX Sensortech VZ89X Sensors sii,s35390a 2-wire CMOS real-time clock +silabs,si7020 Relative Humidity and Temperature Sensors skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply st,24c256 i2c serial eeprom (24cxx) st,m41t00 Serial real-time clock (RTC) diff --git a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt new file mode 100644 index 000000000000..b0d3b59966bc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt @@ -0,0 +1,46 @@ +Invensense MPU-3050 Gyroscope device tree bindings + +Required properties: + - compatible : should be "invensense,mpu3050" + - reg : the I2C address of the sensor + +Optional properties: + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : interrupt mapping for the trigger interrupt from the + internal oscillator. The following IRQ modes are supported: + IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, IRQ_TYPE_LEVEL_HIGH and + IRQ_TYPE_LEVEL_LOW. The driver should detect and configure the hardware + for the desired interrupt type. + - vdd-supply : supply regulator for the main power voltage. + - vlogic-supply : supply regulator for the signal voltage. + - mount-matrix : see iio/mount-matrix.txt + +Optional subnodes: + - The MPU-3050 will pass through and forward the I2C signals from the + incoming I2C bus, alternatively drive traffic to a slave device (usually + an accelerometer) on its own initiative. Therefore is supports a subnode + i2c gate node. For details see: i2c/i2c-gate.txt + +Example: + +mpu3050@68 { + compatible = "invensense,mpu3050"; + reg = <0x68>; + interrupt-parent = <&foo>; + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&bar>; + vlogic-supply = <&baz>; + + /* External I2C interface */ + i2c-gate { + #address-cells = <1>; + #size-cells = <0>; + + fnord@18 { + compatible = "fnord"; + reg = <0x18>; + interrupt-parent = <&foo>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/light/tsl2583.txt b/Documentation/devicetree/bindings/iio/light/tsl2583.txt new file mode 100644 index 000000000000..8e2066c83f70 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/tsl2583.txt @@ -0,0 +1,26 @@ +* TAOS TSL 2580/2581/2583 ALS sensor + +Required properties: + + - compatible: Should be one of + "amstaos,tsl2580" + "amstaos,tsl2581" + "amstaos,tsl2583" + - reg: the I2C address of the device + +Optional properties: + + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + + - vcc-supply: phandle to the regulator that provides power to the sensor. + +Example: + +tsl2581@29 { + compatible = "amstaos,tsl2581"; + reg = <0x29>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index e41fe340162b..c040c9ad1889 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -42,6 +42,7 @@ Accelerometers: - st,lsm303agr-accel - st,lis2dh12-accel - st,h3lis331dl-accel +- st,lng2dm-accel Gyroscopes: - st,l3g4200d-gyro |