diff options
-rw-r--r-- | Documentation/devicetree/bindings/thermal/exynos-thermal.txt | 18 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/thermal/mediatek-thermal.txt | 43 | ||||
-rw-r--r-- | Documentation/thermal/sysfs-api.txt | 68 | ||||
-rw-r--r-- | drivers/thermal/Kconfig | 21 | ||||
-rw-r--r-- | drivers/thermal/Makefile | 1 | ||||
-rw-r--r-- | drivers/thermal/intel_pch_thermal.c | 6 | ||||
-rw-r--r-- | drivers/thermal/mtk_thermal.c | 625 | ||||
-rw-r--r-- | drivers/thermal/of-thermal.c | 81 | ||||
-rw-r--r-- | drivers/thermal/rcar_thermal.c | 3 | ||||
-rw-r--r-- | drivers/thermal/rockchip_thermal.c | 239 | ||||
-rw-r--r-- | drivers/thermal/samsung/Kconfig | 1 | ||||
-rw-r--r-- | drivers/thermal/samsung/exynos_tmu.c | 19 | ||||
-rw-r--r-- | drivers/thermal/tegra_soctherm.c | 2 | ||||
-rw-r--r-- | drivers/thermal/thermal_core.c | 13 | ||||
-rw-r--r-- | drivers/thermal/ti-soc-thermal/ti-bandgap.c | 10 | ||||
-rw-r--r-- | include/linux/thermal.h | 20 | ||||
-rw-r--r-- | include/trace/events/thermal.h | 16 |
17 files changed, 1065 insertions, 121 deletions
diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt index 695150a4136b..70b4c16c7ed8 100644 --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt @@ -11,6 +11,7 @@ "samsung,exynos5420-tmu" for TMU channel 0, 1 on Exynos5420 "samsung,exynos5420-tmu-ext-triminfo" for TMU channels 2, 3 and 4 Exynos5420 (Must pass triminfo base and triminfo clock) + "samsung,exynos5433-tmu" "samsung,exynos5440-tmu" "samsung,exynos7-tmu" - interrupt-parent : The phandle for the interrupt controller @@ -40,9 +41,14 @@ for current TMU channel -- "tmu_sclk" clock for functional operation of the current TMU channel -- vtmu-supply: This entry is optional and provides the regulator node supplying - voltage to TMU. If needed this entry can be placed inside - board/platform specific dts file. + +The Exynos TMU supports generating interrupts when reaching given +temperature thresholds. Number of supported thermal trip points depends +on the SoC (only first trip points defined in DT will be configured): + - most of SoC: 4 + - samsung,exynos5433-tmu: 8 + - samsung,exynos7-tmu: 8 + Following properties are mandatory (depending on SoC): - samsung,tmu_gain: Gain value for internal TMU operation. - samsung,tmu_reference_voltage: Value of TMU IP block's reference voltage @@ -56,6 +62,12 @@ Following properties are mandatory (depending on SoC): - samsung,tmu_default_temp_offset: Default temperature offset - samsung,tmu_cal_type: Callibration type +** Optional properties: + +- vtmu-supply: This entry is optional and provides the regulator node supplying + voltage to TMU. If needed this entry can be placed inside + board/platform specific dts file. + Example 1): tmu@100C0000 { diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt new file mode 100644 index 000000000000..81f9a512bc2a --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt @@ -0,0 +1,43 @@ +* Mediatek Thermal + +This describes the device tree binding for the Mediatek thermal controller +which measures the on-SoC temperatures. This device does not have its own ADC, +instead it directly controls the AUXADC via AHB bus accesses. For this reason +this device needs phandles to the AUXADC. Also it controls a mux in the +apmixedsys register space via AHB bus accesses, so a phandle to the APMIXEDSYS +is also needed. + +Required properties: +- compatible: "mediatek,mt8173-thermal" +- reg: Address range of the thermal controller +- interrupts: IRQ for the thermal controller +- clocks, clock-names: Clocks needed for the thermal controller. required + clocks are: + "therm": Main clock needed for register access + "auxadc": The AUXADC clock +- resets: Reference to the reset controller controlling the thermal controller. +- mediatek,auxadc: A phandle to the AUXADC which the thermal controller uses +- mediatek,apmixedsys: A phandle to the APMIXEDSYS controller. +- #thermal-sensor-cells : Should be 0. See ./thermal.txt for a description. + +Optional properties: +- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If + unspecified default values shall be used. +- nvmem-cell-names: Should be "calibration-data" + +Example: + + thermal: thermal@1100b000 { + #thermal-sensor-cells = <1>; + compatible = "mediatek,mt8173-thermal"; + reg = <0 0x1100b000 0 0x1000>; + interrupts = <0 70 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>; + clock-names = "therm", "auxadc"; + resets = <&pericfg MT8173_PERI_THERM_SW_RST>; + reset-names = "therm"; + mediatek,auxadc = <&auxadc>; + mediatek,apmixedsys = <&apmixedsys>; + nvmem-cells = <&thermal_calibration_data>; + nvmem-cell-names = "calibration-data"; + }; diff --git a/Documentation/thermal/sysfs-api.txt b/Documentation/thermal/sysfs-api.txt index 8c745c8931da..ed419d6c8dec 100644 --- a/Documentation/thermal/sysfs-api.txt +++ b/Documentation/thermal/sysfs-api.txt @@ -72,6 +72,74 @@ temperature) and throttle appropriate devices. It deletes the corresponding entry form /sys/class/thermal folder and unbind all the thermal cooling devices it uses. +1.1.3 struct thermal_zone_device *thermal_zone_of_sensor_register( + struct device *dev, int sensor_id, void *data, + const struct thermal_zone_of_device_ops *ops) + + This interface adds a new sensor to a DT thermal zone. + This function will search the list of thermal zones described in + device tree and look for the zone that refer to the sensor device + pointed by dev->of_node as temperature providers. For the zone + pointing to the sensor node, the sensor will be added to the DT + thermal zone device. + + The parameters for this interface are: + dev: Device node of sensor containing valid node pointer in + dev->of_node. + sensor_id: a sensor identifier, in case the sensor IP has more + than one sensors + data: a private pointer (owned by the caller) that will be + passed back, when a temperature reading is needed. + ops: struct thermal_zone_of_device_ops *. + + get_temp: a pointer to a function that reads the + sensor temperature. This is mandatory + callback provided by sensor driver. + get_trend: a pointer to a function that reads the + sensor temperature trend. + set_emul_temp: a pointer to a function that sets + sensor emulated temperature. + The thermal zone temperature is provided by the get_temp() function + pointer of thermal_zone_of_device_ops. When called, it will + have the private pointer @data back. + + It returns error pointer if fails otherwise valid thermal zone device + handle. Caller should check the return handle with IS_ERR() for finding + whether success or not. + +1.1.4 void thermal_zone_of_sensor_unregister(struct device *dev, + struct thermal_zone_device *tzd) + + This interface unregisters a sensor from a DT thermal zone which was + successfully added by interface thermal_zone_of_sensor_register(). + This function removes the sensor callbacks and private data from the + thermal zone device registered with thermal_zone_of_sensor_register() + interface. It will also silent the zone by remove the .get_temp() and + get_trend() thermal zone device callbacks. + +1.1.5 struct thermal_zone_device *devm_thermal_zone_of_sensor_register( + struct device *dev, int sensor_id, + void *data, const struct thermal_zone_of_device_ops *ops) + + This interface is resource managed version of + thermal_zone_of_sensor_register(). + All details of thermal_zone_of_sensor_register() described in + section 1.1.3 is applicable here. + The benefit of using this interface to register sensor is that it + is not require to explicitly call thermal_zone_of_sensor_unregister() + in error path or during driver unbinding as this is done by driver + resource manager. + +1.1.6 void devm_thermal_zone_of_sensor_unregister(struct device *dev, + struct thermal_zone_device *tzd) + + This interface is resource managed version of + thermal_zone_of_sensor_unregister(). + All details of thermal_zone_of_sensor_unregister() described in + section 1.1.4 is applicable here. + Normally this function will not need to be called and the resource + management code will ensure that the resource is freed. + 1.2 thermal cooling device interface 1.2.1 struct thermal_cooling_device *thermal_cooling_device_register(char *name, void *devdata, struct thermal_cooling_device_ops *) diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig index 7c92c09be213..c37eedc35a24 100644 --- a/drivers/thermal/Kconfig +++ b/drivers/thermal/Kconfig @@ -178,6 +178,7 @@ config THERMAL_EMULATION config HISI_THERMAL tristate "Hisilicon thermal driver" depends on (ARCH_HISI && CPU_THERMAL && OF) || COMPILE_TEST + depends on HAS_IOMEM help Enable this to plug hisilicon's thermal sensor driver into the Linux thermal framework. cpufreq is used as the cooling device to throttle @@ -197,6 +198,7 @@ config IMX_THERMAL config SPEAR_THERMAL tristate "SPEAr thermal sensor driver" depends on PLAT_SPEAR || COMPILE_TEST + depends on HAS_IOMEM depends on OF help Enable this to plug the SPEAr thermal sensor driver into the Linux @@ -206,6 +208,7 @@ config ROCKCHIP_THERMAL tristate "Rockchip thermal driver" depends on ARCH_ROCKCHIP || COMPILE_TEST depends on RESET_CONTROLLER + depends on HAS_IOMEM help Rockchip thermal driver provides support for Temperature sensor ADC (TS-ADC) found on Rockchip SoCs. It supports one critical @@ -214,7 +217,7 @@ config ROCKCHIP_THERMAL config RCAR_THERMAL tristate "Renesas R-Car thermal driver" - depends on ARCH_SHMOBILE || COMPILE_TEST + depends on ARCH_RENESAS || COMPILE_TEST depends on HAS_IOMEM help Enable this to plug the R-Car thermal sensor driver into the Linux @@ -223,6 +226,7 @@ config RCAR_THERMAL config KIRKWOOD_THERMAL tristate "Temperature sensor on Marvell Kirkwood SoCs" depends on MACH_KIRKWOOD || COMPILE_TEST + depends on HAS_IOMEM depends on OF help Support for the Kirkwood thermal sensor driver into the Linux thermal @@ -231,6 +235,7 @@ config KIRKWOOD_THERMAL config DOVE_THERMAL tristate "Temperature sensor on Marvell Dove SoCs" depends on ARCH_DOVE || MACH_DOVE || COMPILE_TEST + depends on HAS_IOMEM depends on OF help Support for the Dove thermal sensor driver in the Linux thermal @@ -249,6 +254,7 @@ config DB8500_THERMAL config ARMADA_THERMAL tristate "Armada 370/XP thermal management" depends on ARCH_MVEBU || COMPILE_TEST + depends on HAS_IOMEM depends on OF help Enable this option if you want to have support for thermal management @@ -266,7 +272,8 @@ config TEGRA_SOCTHERM config DB8500_CPUFREQ_COOLING tristate "DB8500 cpufreq cooling" - depends on ARCH_U8500 + depends on ARCH_U8500 || COMPILE_TEST + depends on HAS_IOMEM depends on CPU_THERMAL default y help @@ -365,8 +372,18 @@ config INTEL_PCH_THERMAL Thermal reporting device will provide temperature reading, programmable trip points and other information. +config MTK_THERMAL + tristate "Temperature sensor driver for mediatek SoCs" + depends on ARCH_MEDIATEK || COMPILE_TEST + depends on HAS_IOMEM + default y + help + Enable this option if you want to have support for thermal management + controller present in Mediatek SoCs + menu "Texas Instruments thermal drivers" depends on ARCH_HAS_BANDGAP || COMPILE_TEST +depends on HAS_IOMEM source "drivers/thermal/ti-soc-thermal/Kconfig" endmenu diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile index cfae6a654793..8e9cbc3b5679 100644 --- a/drivers/thermal/Makefile +++ b/drivers/thermal/Makefile @@ -48,3 +48,4 @@ obj-$(CONFIG_INTEL_PCH_THERMAL) += intel_pch_thermal.o obj-$(CONFIG_ST_THERMAL) += st/ obj-$(CONFIG_TEGRA_SOCTHERM) += tegra_soctherm.o obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o +obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o diff --git a/drivers/thermal/intel_pch_thermal.c b/drivers/thermal/intel_pch_thermal.c index 00d81af648b8..6a6ec1c95a7a 100644 --- a/drivers/thermal/intel_pch_thermal.c +++ b/drivers/thermal/intel_pch_thermal.c @@ -24,6 +24,7 @@ /* Intel PCH thermal Device IDs */ #define PCH_THERMAL_DID_WPT 0x9CA4 /* Wildcat Point */ +#define PCH_THERMAL_DID_SKL 0x9D31 /* Skylake PCH */ /* Wildcat Point-LP PCH Thermal registers */ #define WPT_TEMP 0x0000 /* Temperature */ @@ -201,6 +202,10 @@ static int intel_pch_thermal_probe(struct pci_dev *pdev, ptd->ops = &pch_dev_ops_wpt; dev_name = "pch_wildcat_point"; break; + case PCH_THERMAL_DID_SKL: + ptd->ops = &pch_dev_ops_wpt; + dev_name = "pch_skylake"; + break; default: dev_err(&pdev->dev, "unknown pch thermal device\n"); return -ENODEV; @@ -266,6 +271,7 @@ static void intel_pch_thermal_remove(struct pci_dev *pdev) static struct pci_device_id intel_pch_thermal_id[] = { { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_WPT) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_SKL) }, { 0, }, }; MODULE_DEVICE_TABLE(pci, intel_pch_thermal_id); diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c new file mode 100644 index 000000000000..3d93b1c07cee --- /dev/null +++ b/drivers/thermal/mtk_thermal.c @@ -0,0 +1,625 @@ +/* + * Copyright (c) 2015 MediaTek Inc. + * Author: Hanyi Wu <hanyi.wu@mediatek.com> + * Sascha Hauer <s.hauer@pengutronix.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/nvmem-consumer.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/io.h> +#include <linux/thermal.h> +#include <linux/reset.h> +#include <linux/types.h> +#include <linux/nvmem-consumer.h> + +/* AUXADC Registers */ +#define AUXADC_CON0_V 0x000 +#define AUXADC_CON1_V 0x004 +#define AUXADC_CON1_SET_V 0x008 +#define AUXADC_CON1_CLR_V 0x00c +#define AUXADC_CON2_V 0x010 +#define AUXADC_DATA(channel) (0x14 + (channel) * 4) +#define AUXADC_MISC_V 0x094 + +#define AUXADC_CON1_CHANNEL(x) BIT(x) + +#define APMIXED_SYS_TS_CON1 0x604 + +/* Thermal Controller Registers */ +#define TEMP_MONCTL0 0x000 +#define TEMP_MONCTL1 0x004 +#define TEMP_MONCTL2 0x008 +#define TEMP_MONIDET0 0x014 +#define TEMP_MONIDET1 0x018 +#define TEMP_MSRCTL0 0x038 +#define TEMP_AHBPOLL 0x040 +#define TEMP_AHBTO 0x044 +#define TEMP_ADCPNP0 0x048 +#define TEMP_ADCPNP1 0x04c +#define TEMP_ADCPNP2 0x050 +#define TEMP_ADCPNP3 0x0b4 + +#define TEMP_ADCMUX 0x054 +#define TEMP_ADCEN 0x060 +#define TEMP_PNPMUXADDR 0x064 +#define TEMP_ADCMUXADDR 0x068 +#define TEMP_ADCENADDR 0x074 +#define TEMP_ADCVALIDADDR 0x078 +#define TEMP_ADCVOLTADDR 0x07c +#define TEMP_RDCTRL 0x080 +#define TEMP_ADCVALIDMASK 0x084 +#define TEMP_ADCVOLTAGESHIFT 0x088 +#define TEMP_ADCWRITECTRL 0x08c +#define TEMP_MSR0 0x090 +#define TEMP_MSR1 0x094 +#define TEMP_MSR2 0x098 +#define TEMP_MSR3 0x0B8 + +#define TEMP_SPARE0 0x0f0 + +#define PTPCORESEL 0x400 + +#define TEMP_MONCTL1_PERIOD_UNIT(x) ((x) & 0x3ff) + +#define TEMP_MONCTL2_FILTER_INTERVAL(x) (((x) & 0x3ff) << 16) +#define TEMP_MONCTL2_SENSOR_INTERVAL(x) ((x) & 0x3ff) + +#define TEMP_AHBPOLL_ADC_POLL_INTERVAL(x) (x) + +#define TEMP_ADCWRITECTRL_ADC_PNP_WRITE BIT(0) +#define TEMP_ADCWRITECTRL_ADC_MUX_WRITE BIT(1) + +#define TEMP_ADCVALIDMASK_VALID_HIGH BIT(5) +#define TEMP_ADCVALIDMASK_VALID_POS(bit) (bit) + +#define MT8173_TS1 0 +#define MT8173_TS2 1 +#define MT8173_TS3 2 +#define MT8173_TS4 3 +#define MT8173_TSABB 4 + +/* AUXADC channel 11 is used for the temperature sensors */ +#define MT8173_TEMP_AUXADC_CHANNEL 11 + +/* The total number of temperature sensors in the MT8173 */ +#define MT8173_NUM_SENSORS 5 + +/* The number of banks in the MT8173 */ +#define MT8173_NUM_ZONES 4 + +/* The number of sensing points per bank */ +#define MT8173_NUM_SENSORS_PER_ZONE 4 + +/* Layout of the fuses providing the calibration data */ +#define MT8173_CALIB_BUF0_VALID BIT(0) +#define MT8173_CALIB_BUF1_ADC_GE(x) (((x) >> 22) & 0x3ff) +#define MT8173_CALIB_BUF0_VTS_TS1(x) (((x) >> 17) & 0x1ff) +#define MT8173_CALIB_BUF0_VTS_TS2(x) (((x) >> 8) & 0x1ff) +#define MT8173_CALIB_BUF1_VTS_TS3(x) (((x) >> 0) & 0x1ff) +#define MT8173_CALIB_BUF2_VTS_TS4(x) (((x) >> 23) & 0x1ff) +#define MT8173_CALIB_BUF2_VTS_TSABB(x) (((x) >> 14) & 0x1ff) +#define MT8173_CALIB_BUF0_DEGC_CALI(x) (((x) >> 1) & 0x3f) +#define MT8173_CALIB_BUF0_O_SLOPE(x) (((x) >> 26) & 0x3f) + +#define THERMAL_NAME "mtk-thermal" + +struct mtk_thermal; + +struct mtk_thermal_bank { + struct mtk_thermal *mt; + int id; +}; + +struct mtk_thermal { + struct device *dev; + void __iomem *thermal_base; + + struct clk *clk_peri_therm; + struct clk *clk_auxadc; + + struct mtk_thermal_bank banks[MT8173_NUM_ZONES]; + + /* lock: for getting and putting banks */ + struct mutex lock; + + /* Calibration values */ + s32 adc_ge; + s32 degc_cali; + s32 o_slope; + s32 vts[MT8173_NUM_SENSORS]; + + struct thermal_zone_device *tzd; +}; + +struct mtk_thermal_bank_cfg { + unsigned int num_sensors; + unsigned int sensors[MT8173_NUM_SENSORS_PER_ZONE]; +}; + +static const int sensor_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 }; + +/* + * The MT8173 thermal controller has four banks. Each bank can read up to + * four temperature sensors simultaneously. The MT8173 has a total of 5 + * temperature sensors. We use each bank to measure a certain area of the + * SoC. Since TS2 is located centrally in the SoC it is influenced by multiple + * areas, hence is used in different banks. + * + * The thermal core only gets the maximum temperature of all banks, so + * the bank concept wouldn't be necessary here. However, the SVS (Smart + * Voltage Scaling) unit makes its decisions based on the same bank + * data, and this indeed needs the temperatures of the individual banks + * for making better decisions. + */ +static const struct mtk_thermal_bank_cfg bank_data[] = { + { + .num_sensors = 2, + .sensors = { MT8173_TS2, MT8173_TS3 }, + }, { + .num_sensors = 2, + .sensors = { MT8173_TS2, MT8173_TS4 }, + }, { + .num_sensors = 3, + .sensors = { MT8173_TS1, MT8173_TS2, MT8173_TSABB }, + }, { + .num_sensors = 1, + .sensors = { MT8173_TS2 }, + }, +}; + +struct mtk_thermal_sense_point { + int msr; + int adcpnp; +}; + +static const struct mtk_thermal_sense_point + sensing_points[MT8173_NUM_SENSORS_PER_ZONE] = { + { + .msr = TEMP_MSR0, + .adcpnp = TEMP_ADCPNP0, + }, { + .msr = TEMP_MSR1, + .adcpnp = TEMP_ADCPNP1, + }, { + .msr = TEMP_MSR2, + .adcpnp = TEMP_ADCPNP2, + }, { + .msr = TEMP_MSR3, + .adcpnp = TEMP_ADCPNP3, + }, +}; + +/** + * raw_to_mcelsius - convert a raw ADC value to mcelsius + * @mt: The thermal controller + * @raw: raw ADC value + * + * This converts the raw ADC value to mcelsius using the SoC specific + * calibration constants + */ +static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw) +{ + s32 tmp; + + raw &= 0xfff; + + tmp = 203450520 << 3; + tmp /= 165 + mt->o_slope; + tmp /= 10000 + mt->adc_ge; + tmp *= raw - mt->vts[sensno] - 3350; + tmp >>= 3; + + return mt->degc_cali * 500 - tmp; +} + +/** + * mtk_thermal_get_bank - get bank + * @bank: The bank + * + * The bank registers are banked, we have to select a bank in the + * PTPCORESEL register to access it. + */ +static void mtk_thermal_get_bank(struct mtk_thermal_bank *bank) +{ + struct mtk_thermal *mt = bank->mt; + u32 val; + + mutex_lock(&mt->lock); + + val = readl(mt->thermal_base + PTPCORESEL); + val &= ~0xf; + val |= bank->id; + writel(val, mt->thermal_base + PTPCORESEL); +} + +/** + * mtk_thermal_put_bank - release bank + * @bank: The bank + * + * release a bank previously taken with mtk_thermal_get_bank, + */ +static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank) +{ + struct mtk_thermal *mt = bank->mt; + + mutex_unlock(&mt->lock); +} + +/** + * mtk_thermal_bank_temperature - get the temperature of a bank + * @bank: The bank + * + * The temperature of a bank is considered the maximum temperature of + * the sensors associated to the bank. + */ +static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank) +{ + struct mtk_thermal *mt = bank->mt; + int i, temp = INT_MIN, max = INT_MIN; + u32 raw; + + for (i = 0; i < bank_data[bank->id].num_sensors; i++) { + raw = readl(mt->thermal_base + sensing_points[i].msr); + + temp = raw_to_mcelsius(mt, bank_data[bank->id].sensors[i], raw); + + /* + * The first read of a sensor often contains very high bogus + * temperature value. Filter these out so that the system does + * not immediately shut down. + */ + if (temp > 200000) + temp = 0; + + if (temp > max) + max = temp; + } + + return max; +} + +static int mtk_read_temp(void *data, int *temperature) +{ + struct mtk_thermal *mt = data; + int i; + int tempmax = INT_MIN; + + for (i = 0; i < MT8173_NUM_ZONES; i++) { + struct mtk_thermal_bank *bank = &mt->banks[i]; + + mtk_thermal_get_bank(bank); + + tempmax = max(tempmax, mtk_thermal_bank_temperature(bank)); + + mtk_thermal_put_bank(bank); + } + + *temperature = tempmax; + + return 0; +} + +static const struct thermal_zone_of_device_ops mtk_thermal_ops = { + .get_temp = mtk_read_temp, +}; + +static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num, + u32 apmixed_phys_base, u32 auxadc_phys_base) +{ + struct mtk_thermal_bank *bank = &mt->banks[num]; + const struct mtk_thermal_bank_cfg *cfg = &bank_data[num]; + int i; + + bank->id = num; + bank->mt = mt; + + mtk_thermal_get_bank(bank); + + /* bus clock 66M counting unit is 12 * 15.15ns * 256 = 46.540us */ + writel(TEMP_MONCTL1_PERIOD_UNIT(12), mt->thermal_base + TEMP_MONCTL1); + + /* + * filt interval is 1 * 46.540us = 46.54us, + * sen interval is 429 * 46.540us = 19.96ms + */ + writel(TEMP_MONCTL2_FILTER_INTERVAL(1) | + TEMP_MONCTL2_SENSOR_INTERVAL(429), + mt->thermal_base + TEMP_MONCTL2); + + /* poll is set to 10u */ + writel(TEMP_AHBPOLL_ADC_POLL_INTERVAL(768), + mt->thermal_base + TEMP_AHBPOLL); + + /* temperature sampling control, 1 sample */ + writel(0x0, mt->thermal_base + TEMP_MSRCTL0); + + /* exceed this polling time, IRQ would be inserted */ + writel(0xffffffff, mt->thermal_base + TEMP_AHBTO); + + /* number of interrupts per event, 1 is enough */ + writel(0x0, mt->thermal_base + TEMP_MONIDET0); + writel(0x0, mt->thermal_base + TEMP_MONIDET1); + + /* + * The MT8173 thermal controller does not have its own ADC. Instead it + * uses AHB bus accesses to control the AUXADC. To do this the thermal + * controller has to be programmed with the physical addresses of the + * AUXADC registers and with the various bit positions in the AUXADC. + * Also the thermal controller controls a mux in the APMIXEDSYS register + * space. + */ + + /* + * this value will be stored to TEMP_PNPMUXADDR (TEMP_SPARE0) + * automatically by hw + */ + writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCMUX); + + /* AHB address for auxadc mux selection */ + writel(auxadc_phys_base + AUXADC_CON1_CLR_V, + mt->thermal_base + TEMP_ADCMUXADDR); + + /* AHB address for pnp sensor mux selection */ + writel(apmixed_phys_base + APMIXED_SYS_TS_CON1, + mt->thermal_base + TEMP_PNPMUXADDR); + + /* AHB value for auxadc enable */ + writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCEN); + + /* AHB address for auxadc enable (channel 0 immediate mode selected) */ + writel(auxadc_phys_base + AUXADC_CON1_SET_V, + mt->thermal_base + TEMP_ADCENADDR); + + /* AHB address for auxadc valid bit */ + writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL), + mt->thermal_base + TEMP_ADCVALIDADDR); + + /* AHB address for auxadc voltage output */ + writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL), + mt->thermal_base + TEMP_ADCVOLTADDR); + + /* read valid & voltage are at the same register */ + writel(0x0, mt->thermal_base + TEMP_RDCTRL); + + /* indicate where the valid bit is */ + writel(TEMP_ADCVALIDMASK_VALID_HIGH | TEMP_ADCVALIDMASK_VALID_POS(12), + mt->thermal_base + TEMP_ADCVALIDMASK); + + /* no shift */ + writel(0x0, mt->thermal_base + TEMP_ADCVOLTAGESHIFT); + + /* enable auxadc mux write transaction */ + writel(TEMP_ADCWRITECTRL_ADC_MUX_WRITE, + mt->thermal_base + TEMP_ADCWRITECTRL); + + for (i = 0; i < cfg->num_sensors; i++) + writel(sensor_mux_values[cfg->sensors[i]], + mt->thermal_base + sensing_points[i].adcpnp); + + writel((1 << cfg->num_sensors) - 1, mt->thermal_base + TEMP_MONCTL0); + + writel(TEMP_ADCWRITECTRL_ADC_PNP_WRITE | + TEMP_ADCWRITECTRL_ADC_MUX_WRITE, + mt->thermal_base + TEMP_ADCWRITECTRL); + + mtk_thermal_put_bank(bank); +} + +static u64 of_get_phys_base(struct device_node *np) +{ + u64 size64; + const __be32 *regaddr_p; + + regaddr_p = of_get_address(np, 0, &size64, NULL); + if (!regaddr_p) + return OF_BAD_ADDR; + + return of_translate_address(np, regaddr_p); +} + +static int mtk_thermal_get_calibration_data(struct device *dev, + struct mtk_thermal *mt) +{ + struct nvmem_cell *cell; + u32 *buf; + size_t len; + int i, ret = 0; + + /* Start with default values */ + mt->adc_ge = 512; + for (i = 0; i < MT8173_NUM_SENSORS; i++) + mt->vts[i] = 260; + mt->degc_cali = 40; + mt->o_slope = 0; + + cell = nvmem_cell_get(dev, "calibration-data"); + if (IS_ERR(cell)) { + if (PTR_ERR(cell) == -EPROBE_DEFER) + return PTR_ERR(cell); + return 0; + } + + buf = (u32 *)nvmem_cell_read(cell, &len); + + nvmem_cell_put(cell); + + if (IS_ERR(buf)) + return PTR_ERR(buf); + + if (len < 3 * sizeof(u32)) { + dev_warn(dev, "invalid calibration data\n"); + ret = -EINVAL; + goto out; + } + + if (buf[0] & MT8173_CALIB_BUF0_VALID) { + mt->adc_ge = MT8173_CALIB_BUF1_ADC_GE(buf[1]); + mt->vts[MT8173_TS1] = MT8173_CALIB_BUF0_VTS_TS1(buf[0]); + mt->vts[MT8173_TS2] = MT8173_CALIB_BUF0_VTS_TS2(buf[0]); + mt->vts[MT8173_TS3] = MT8173_CALIB_BUF1_VTS_TS3(buf[1]); + mt->vts[MT8173_TS4] = MT8173_CALIB_BUF2_VTS_TS4(buf[2]); + mt->vts[MT8173_TSABB] = MT8173_CALIB_BUF2_VTS_TSABB(buf[2]); + mt->degc_cali = MT8173_CALIB_BUF0_DEGC_CALI(buf[0]); + mt->o_slope = MT8173_CALIB_BUF0_O_SLOPE(buf[0]); + } else { + dev_info(dev, "Device not calibrated, using default calibration values\n"); + } + +out: + kfree(buf); + + return ret; +} + +static int mtk_thermal_probe(struct platform_device *pdev) +{ + int ret, i; + struct device_node *auxadc, *apmixedsys, *np = pdev->dev.of_node; + struct mtk_thermal *mt; + struct resource *res; + u64 auxadc_phys_base, apmixed_phys_base; + + mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL); + if (!mt) + return -ENOMEM; + + mt->clk_peri_therm = devm_clk_get(&pdev->dev, "therm"); + if (IS_ERR(mt->clk_peri_therm)) + return PTR_ERR(mt->clk_peri_therm); + + mt->clk_auxadc = devm_clk_get(&pdev->dev, "auxadc"); + if (IS_ERR(mt->clk_auxadc)) + return PTR_ERR(mt->clk_auxadc); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + mt->thermal_base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(mt->thermal_base)) + return PTR_ERR(mt->thermal_base); + + ret = mtk_thermal_get_calibration_data(&pdev->dev, mt); + if (ret) + return ret; + + mutex_init(&mt->lock); + + mt->dev = &pdev->dev; + + auxadc = of_parse_phandle(np, "mediatek,auxadc", 0); + if (!auxadc) { + dev_err(&pdev->dev, "missing auxadc node\n"); + return -ENODEV; + } + + auxadc_phys_base = of_get_phys_base(auxadc); + + of_node_put(auxadc); + + if (auxadc_phys_base == OF_BAD_ADDR) { + dev_err(&pdev->dev, "Can't get auxadc phys address\n"); + return -EINVAL; + } + + apmixedsys = of_parse_phandle(np, "mediatek,apmixedsys", 0); + if (!apmixedsys) { + dev_err(&pdev->dev, "missing apmixedsys node\n"); + return -ENODEV; + } + + apmixed_phys_base = of_get_phys_base(apmixedsys); + + of_node_put(apmixedsys); + + if (apmixed_phys_base == OF_BAD_ADDR) { + dev_err(&pdev->dev, "Can't get auxadc phys address\n"); + return -EINVAL; + } + + ret = clk_prepare_enable(mt->clk_auxadc); + if (ret) { + dev_err(&pdev->dev, "Can't enable auxadc clk: %d\n", ret); + return ret; + } + + ret = device_reset(&pdev->dev); + if (ret) + goto err_disable_clk_auxadc; + + ret = clk_prepare_enable(mt->clk_peri_therm); + if (ret) { + dev_err(&pdev->dev, "Can't enable peri clk: %d\n", ret); + goto err_disable_clk_auxadc; + } + + for (i = 0; i < MT8173_NUM_ZONES; i++) + mtk_thermal_init_bank(mt, i, apmixed_phys_base, + auxadc_phys_base); + + platform_set_drvdata(pdev, mt); + + mt->tzd = thermal_zone_of_sensor_register(&pdev->dev, 0, mt, + &mtk_thermal_ops); + if (IS_ERR(mt->tzd)) + goto err_register; + + return 0; + +err_register: + clk_disable_unprepare(mt->clk_peri_therm); + +err_disable_clk_auxadc: + clk_disable_unprepare(mt->clk_auxadc); + + return ret; +} + +static int mtk_thermal_remove(struct platform_device *pdev) +{ + struct mtk_thermal *mt = platform_get_drvdata(pdev); + + thermal_zone_of_sensor_unregister(&pdev->dev, mt->tzd); + + clk_disable_unprepare(mt->clk_peri_therm); + clk_disable_unprepare(mt->clk_auxadc); + + return 0; +} + +static const struct of_device_id mtk_thermal_of_match[] = { + { + .compatible = "mediatek,mt8173-thermal", + }, { + }, +}; + +static struct platform_driver mtk_thermal_driver = { + .probe = mtk_thermal_probe, + .remove = mtk_thermal_remove, + .driver = { + .name = THERMAL_NAME, + .of_match_table = mtk_thermal_of_match, + }, +}; + +module_platform_driver(mtk_thermal_driver); + +MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de"); +MODULE_AUTHOR("Hanyi Wu <hanyi.wu@mediatek.com>"); +MODULE_DESCRIPTION("Mediatek thermal driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/thermal/of-thermal.c b/drivers/thermal/of-thermal.c index 9043f8f91852..49ac23d3e776 100644 --- a/drivers/thermal/of-thermal.c +++ b/drivers/thermal/of-thermal.c @@ -555,6 +555,87 @@ void thermal_zone_of_sensor_unregister(struct device *dev, } EXPORT_SYMBOL_GPL(thermal_zone_of_sensor_unregister); +static void devm_thermal_zone_of_sensor_release(struct device *dev, void *res) +{ + thermal_zone_of_sensor_unregister(dev, + *(struct thermal_zone_device **)res); +} + +static int devm_thermal_zone_of_sensor_match(struct device *dev, void *res, + void *data) +{ + struct thermal_zone_device **r = res; + + if (WARN_ON(!r || !*r)) + return 0; + + return *r == data; +} + +/** + * devm_thermal_zone_of_sensor_register - Resource managed version of + * thermal_zone_of_sensor_register() + * @dev: a valid struct device pointer of a sensor device. Must contain + * a valid .of_node, for the sensor node. + * @sensor_id: a sensor identifier, in case the sensor IP has more + * than one sensors + * @data: a private pointer (owned by the caller) that will be passed + * back, when a temperature reading is needed. + * @ops: struct thermal_zone_of_device_ops *. Must contain at least .get_temp. + * + * Refer thermal_zone_of_sensor_register() for more details. + * + * Return: On success returns a valid struct thermal_zone_device, + * otherwise, it returns a corresponding ERR_PTR(). Caller must + * check the return value wit |