diff options
116 files changed, 1521 insertions, 423 deletions
diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index 93147c0c8a0e..fcbae6a5e6c1 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -12,14 +12,33 @@ its hardware characteristcs. * compatible: These have to be supplemented with "arm,primecell" as drivers are using the AMBA bus interface. Possible values include: - - "arm,coresight-etb10", "arm,primecell"; - - "arm,coresight-tpiu", "arm,primecell"; - - "arm,coresight-tmc", "arm,primecell"; - - "arm,coresight-funnel", "arm,primecell"; - - "arm,coresight-etm3x", "arm,primecell"; - - "arm,coresight-etm4x", "arm,primecell"; - - "qcom,coresight-replicator1x", "arm,primecell"; - - "arm,coresight-stm", "arm,primecell"; [1] + - Embedded Trace Buffer (version 1.0): + "arm,coresight-etb10", "arm,primecell"; + + - Trace Port Interface Unit: + "arm,coresight-tpiu", "arm,primecell"; + + - Trace Memory Controller, used for Embedded Trace Buffer(ETB), + Embedded Trace FIFO(ETF) and Embedded Trace Router(ETR) + configuration. The configuration mode (ETB, ETF, ETR) is + discovered at boot time when the device is probed. + "arm,coresight-tmc", "arm,primecell"; + + - Trace Funnel: + "arm,coresight-funnel", "arm,primecell"; + + - Embedded Trace Macrocell (version 3.x) and + Program Flow Trace Macrocell: + "arm,coresight-etm3x", "arm,primecell"; + + - Embedded Trace Macrocell (version 4.x): + "arm,coresight-etm4x", "arm,primecell"; + + - Qualcomm Configurable Replicator (version 1.x): + "qcom,coresight-replicator1x", "arm,primecell"; + + - System Trace Macrocell: + "arm,coresight-stm", "arm,primecell"; [1] * reg: physical base address and length of the register set(s) of the component. diff --git a/Documentation/devicetree/bindings/arm/l2c2x0.txt b/Documentation/devicetree/bindings/arm/l2c2x0.txt index c453ab5553cd..917199f17965 100644 --- a/Documentation/devicetree/bindings/arm/l2c2x0.txt +++ b/Documentation/devicetree/bindings/arm/l2c2x0.txt @@ -86,10 +86,10 @@ Optional properties: firmware) - arm,dynamic-clock-gating : L2 dynamic clock gating. Value: <0> (forcibly disable), <1> (forcibly enable), property absent (OS specific behavior, - preferrably retain firmware settings) + preferably retain firmware settings) - arm,standby-mode: L2 standby mode enable. Value <0> (forcibly disable), <1> (forcibly enable), property absent (OS specific behavior, - preferrably retain firmware settings) + preferably retain firmware settings) Example: diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index a92d4f3e7044..5c70ce9c1954 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -146,10 +146,10 @@ samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) sgx,vz89x SGX Sensortech VZ89X Sensors sii,s35390a 2-wire CMOS real-time clock skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply -st-micro,24c256 i2c serial eeprom (24cxx) -stm,m41t00 Serial Access TIMEKEEPER -stm,m41t62 Serial real-time clock (RTC) with alarm -stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS +st,24c256 i2c serial eeprom (24cxx) +st,m41t00 Serial real-time clock (RTC) +st,m41t62 Serial real-time clock (RTC) with alarm +st,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,ads7828 8-Channels, 12-bit ADC ti,ads7830 8-Channels, 8-bit ADC diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt index 1857f4a6b9a9..9554292dc6cb 100644 --- a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt +++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt @@ -8,10 +8,13 @@ Sub-nodes: - regulators : Contain the regulator nodes. The DA9052/53 regulators are bound using their names as listed below: - buck0 : regulator BUCK0 - buck1 : regulator BUCK1 - buck2 : regulator BUCK2 - buck3 : regulator BUCK3 + buck1 : regulator BUCK CORE + buck2 : regulator BUCK PRO + buck3 : regulator BUCK MEM + buck4 : regulator BUCK PERI + ldo1 : regulator LDO1 + ldo2 : regulator LDO2 + ldo3 : regulator LDO3 ldo4 : regulator LDO4 ldo5 : regulator LDO5 ldo6 : regulator LDO6 @@ -19,9 +22,6 @@ Sub-nodes: ldo8 : regulator LDO8 ldo9 : regulator LDO9 ldo10 : regulator LDO10 - ldo11 : regulator LDO11 - ldo12 : regulator LDO12 - ldo13 : regulator LDO13 The bindings details of individual regulator device can be found in: Documentation/devicetree/bindings/regulator/regulator.txt @@ -36,22 +36,22 @@ i2c@63fc8000 { /* I2C1 */ reg = <0x48>; regulators { - buck0 { + buck1 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <2075000>; }; - buck1 { + buck2 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <2075000>; }; - buck2 { + buck3 { regulator-min-microvolt = <925000>; regulator-max-microvolt = <2500000>; }; - buck3 { + buck4 { regulator-min-microvolt = <925000>; regulator-max-microvolt = <2500000>; }; diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt index 7dbd158810d2..e3b8fe71762b 100644 --- a/Documentation/devicetree/bindings/net/cavium-pip.txt +++ b/Documentation/devicetree/bindings/net/cavium-pip.txt @@ -37,6 +37,12 @@ Properties for PIP port which is a child the PIP interface: - phy-handle: Optional, see ethernet.txt file in the same directory. +- rx-delay: Delay value for RGMII receive clock. Optional. Disabled if 0. + Value range is 1-31, and mapping to the actual delay varies depending on HW. + +- tx-delay: Delay value for RGMII transmit clock. Optional. Disabled if 0. + Value range is 1-31, and mapping to the actual delay varies depending on HW. + Example: pip@11800a0000000 { diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 9bbbe7f87d67..a4a570fb2494 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -317,7 +317,7 @@ Each port children node must have the following mandatory properties: Note that a port labelled "dsa" will imply checking for the uplink phandle described below. -Optionnal property: +Optional property: - link : Should be a list of phandles to another switch's DSA port. This property is only used when switches are being chained/cascaded together. This port is used as outgoing port |