diff options
130 files changed, 4923 insertions, 676 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt b/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt new file mode 100644 index 000000000000..c3a1b37c4c35 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/microchip,pic32-evic.txt @@ -0,0 +1,67 @@ +Microchip PIC32 Interrupt Controller +==================================== + +The Microchip PIC32 contains an Enhanced Vectored Interrupt Controller (EVIC). +It handles all internal and external interrupts. This controller exists outside +of the CPU and is the arbitrator of all interrupts (including interrupts from +the CPU itself) before they are presented to the CPU. + +External interrupts have a software configurable edge polarity. Non external +interrupts have a type and polarity that is determined by the source of the +interrupt. + +Required properties +------------------- + +- compatible: Should be "microchip,pic32mzda-evic" +- reg: Specifies physical base address and size of register range. +- interrupt-controller: Identifies the node as an interrupt controller. +- #interrupt cells: Specifies the number of cells used to encode an interrupt + source connected to this controller. The value shall be 2 and interrupt + descriptor shall have the following format: + + <hw_irq irq_type> + + hw_irq - represents the hardware interrupt number as in the data sheet. + irq_type - is used to describe the type and polarity of an interrupt. For + internal interrupts use IRQ_TYPE_EDGE_RISING for non persistent interrupts and + IRQ_TYPE_LEVEL_HIGH for persistent interrupts. For external interrupts use + IRQ_TYPE_EDGE_RISING or IRQ_TYPE_EDGE_FALLING to select the desired polarity. + +Optional properties +------------------- +- microchip,external-irqs: u32 array of external interrupts with software + polarity configuration. This array corresponds to the bits in the INTCON + SFR. + +Example +------- + +evic: interrupt-controller@1f810000 { + compatible = "microchip,pic32mzda-evic"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x1f810000 0x1000>; + microchip,external-irqs = <3 8 13 18 23>; +}; + +Each device/peripheral must request its interrupt line with the associated type +and polarity. + +Internal interrupt DTS snippet +------------------------------ + +device@1f800000 { + ... + interrupts = <113 IRQ_TYPE_LEVEL_HIGH>; + ... +}; + +External interrupt DTS snippet +------------------------------ + +device@1f800000 { + ... + interrupts = <3 IRQ_TYPE_EDGE_RISING>; + ... +}; diff --git a/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt b/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt new file mode 100644 index 000000000000..1c8dbc45feec --- /dev/null +++ b/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt @@ -0,0 +1,31 @@ +* Microchip PIC32MZDA Platforms + +PIC32MZDA Starter Kit +Required root node properties: + - compatible = "microchip,pic32mzda-sk", "microchip,pic32mzda" + +CPU nodes: +---------- +A "cpus" node is required. Required properties: + - #address-cells: Must be 1. + - #size-cells: Must be 0. +A CPU sub-node is also required. Required properties: + - device_type: Must be "cpu". + - compatible: Must be "mti,mips14KEc". +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "mti,mips14KEc"; + }; + }; + +Boot protocol +-------------- +In accordance with Unified Hosting Interface Reference Manual (MD01069), the +bootloader must pass the following arguments to the kernel: + - $a0: -2. + - $a1: KSEG0 address of the flattened device-tree blob. diff --git a/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt b |