diff options
64 files changed, 2300 insertions, 741 deletions
diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index d11c3721e7cd..4c388bb2f0a2 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -30,6 +30,22 @@ Optional properties: specifiers, one for transmission, and one for reception. - dma-names : Must contain a list of two DMA names, "tx" and "rx". +- renesas,dtdl : delay sync signal (setup) in transmit mode. + Must contain one of the following values: + 0 (no bit delay) + 50 (0.5-clock-cycle delay) + 100 (1-clock-cycle delay) + 150 (1.5-clock-cycle delay) + 200 (2-clock-cycle delay) + +- renesas,syncdl : delay sync signal (hold) in transmit mode. + Must contain one of the following values: + 0 (no bit delay) + 50 (0.5-clock-cycle delay) + 100 (1-clock-cycle delay) + 150 (1.5-clock-cycle delay) + 200 (2-clock-cycle delay) + 300 (3-clock-cycle delay) Optional properties, deprecated for soctype-specific bindings: - renesas,tx-fifo-size : Overrides the default tx fifo size given in words diff --git a/Documentation/devicetree/bindings/spi/spi-sirf.txt b/Documentation/devicetree/bindings/spi/spi-sirf.txt new file mode 100644 index 000000000000..4c7adb8f777c --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sirf.txt @@ -0,0 +1,41 @@ +* CSR SiRFprimaII Serial Peripheral Interface + +Required properties: +- compatible : Should be "sirf,prima2-spi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI interrupt +- resets: phandle to the reset controller asserting this device in + reset + See ../reset/reset.txt for details. +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + +- #address-cells: Number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: Should be zero. + +Optional properties: +- spi-max-frequency: Specifies maximum SPI clock frequency, + Units - Hz. Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt +- cs-gpios: should specify GPIOs used for chipselects. + +Example: + +spi0: spi@b00d0000 { + compatible = "sirf,prima2-spi"; + reg = <0xb00d0000 0x10000>; + interrupts = <15>; + dmas = <&dmac1 9>, + <&dmac1 4>; + dma-names = "rx", "tx"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clks 19>; + resets = <&rstc 26>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-st-ssc.txt b/Documentation/devicetree/bindings/spi/spi-st-ssc.txt new file mode 100644 index 000000000000..fe54959ec957 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-st-ssc.txt @@ -0,0 +1,40 @@ +STMicroelectronics SSC (SPI) Controller +--------------------------------------- + +Required properties: +- compatible : "st,comms-ssc4-spi" +- reg : Offset and length of the device's register set +- interrupts : The interrupt specifier +- clock-names : Must contain "ssc" +- clocks : Must contain an entry for each name in clock-names + See ../clk/* +- pinctrl-names : Uses "default", can use "sleep" if provided + See ../pinctrl/pinctrl-binding.txt + +Optional properties: +- cs-gpios : List of GPIO chip selects + See ../spi/spi-bus.txt + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Example: + spi@9840000 { + compatible = "st,comms-ssc4-spi"; + reg = <0x9840000 0x110>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; + clock-names = "ssc"; + pinctrl-0 = <&pinctrl_spi0_default>; + pinctrl-names = "default"; + cs-gpios = <&pio17 5 0>; + #address-cells = <1>; + #size-cells = <0>; + + st95hf@0{ + compatible = "st,st95hf"; + reg = <0>; + spi-max-frequency = <1000000>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + }; + }; diff --git a/arch/x86/pci/intel_mid_pci.c b/arch/x86/pci/intel_mid_pci.c index 44b9271580b5..852aa4c92da0 100644 --- a/arch/x86/pci/intel_mid_pci.c +++ b/arch/x86/pci/intel_mid_pci.c @@ -293,7 +293,6 @@ static void mrst_power_off_unused_dev(struct pci_dev *dev) DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0801, mrst_power_off_unused_dev); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0809, mrst_power_off_unused_dev); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x080C, mrst_power_off_unused_dev); -DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0812, mrst_power_off_unused_dev); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0815, mrst_power_off_unused_dev); /* diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 99829985c1a1..95ccedabba4f 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -185,6 +185,16 @@ config SPI_DAVINCI help SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules. +config SPI_DLN2 + tristate "Diolan DLN-2 USB SPI adapter" + depends on MFD_DLN2 + help + If you say yes to this option, support will be included for Diolan + DLN2, a USB to SPI interface. + + This driver can also be built as a module. If so, the module + will be called spi-dln2. + config SPI_EFM32 tristate "EFM32 SPI controller" depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST) @@ -279,7 +289,7 @@ config SPI_FSL_CPM depends on FSL_SOC config SPI_FSL_SPI - bool "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller" + tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller" depends on OF select SPI_FSL_LIB select SPI_FSL_CPM if FSL_SOC @@ -292,7 +302,6 @@ config SPI_FSL_SPI config SPI_FSL_DSPI tristate "Freescale DSPI controller" - select SPI_BITBANG select REGMAP_MMIO depends on SOC_VF610 || COMPILE_TEST help @@ -300,7 +309,7 @@ config SPI_FSL_DSPI mode. VF610 platform uses the controller. config SPI_FSL_ESPI - bool "Freescale eSPI controller" + tristate "Freescale eSPI controller" depends on FSL_SOC select SPI_FSL_LIB help @@ -460,7 +469,6 @@ config SPI_S3C24XX_FIQ config SPI_S3C64XX tristate "Samsung S3C64XX series type SPI" depends on (PLAT_SAMSUNG || ARCH_EXYNOS) - select S3C64XX_PL080 if ARCH_S3C64XX help SPI driver for Samsung S3C64XX and newer SoCs. @@ -503,6 +511,13 @@ config SPI_SIRF help SPI driver for CSR SiRFprimaII SoCs +config SPI_ST_SSC4 + tristate "STMicroelectronics SPI SSC-based driver" + depends on ARCH_STI + help + STMicroelectronics SoCs support for SPI. If you say yes to + this option, support will be included for the SSC driven SPI. + config SPI_SUN4I tristate "Allwinner A10 SoCs SPI controller" depends on ARCH_SUNXI || COMPILE_TEST @@ -595,7 +610,6 @@ config SPI_XTENSA_XTFPGA 16 bit words in SPI mode 0, automatically asserting CS on transfer start and deasserting on end. - config SPI_NUC900 tristate "Nuvoton NUC900 series SPI" depends on ARCH_W90X900 diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 6b9d2ac629cc..d8cbf654976b 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_SPI_CADENCE) += spi-cadence.o obj-$(CONFIG_SPI_CLPS711X) += spi-clps711x.o obj-$(CONFIG_SPI_COLDFIRE_QSPI) += spi-coldfire-qspi.o obj-$(CONFIG_SPI_DAVINCI) += spi-davinci.o +obj-$(CONFIG_SPI_DLN2) += spi-dln2.o obj-$(CONFIG_SPI_DESIGNWARE) += spi-dw.o obj-$(CONFIG_SPI_DW_MMIO) += spi-dw-mmio.o obj-$(CONFIG_SPI_DW_PCI) += spi-dw-midpci.o @@ -76,6 +77,7 @@ obj-$(CONFIG_SPI_SH_HSPI) += spi-sh-hspi.o obj-$(CONFIG_SPI_SH_MSIOF) += spi-sh-msiof.o obj-$(CONFIG_SPI_SH_SCI) += spi-sh-sci.o obj-$(CONFIG_SPI_SIRF) += spi-sirf.o +obj-$(CONFIG_SPI_ST_SSC4) += spi-st-ssc4.o obj-$(CONFIG_SPI_SUN4I) += spi-sun4i.o obj-$(CONFIG_SPI_SUN6I) += spi-sun6i.o obj-$(CONFIG_SPI_TEGRA114) += spi-tegra114.o diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c index 23d8f5f56579..9af7841f2e8c 100644 --- a/drivers/spi/spi-atmel.c +++ b/drivers/spi/spi-atmel.c @@ -1046,6 +1046,7 @@ static int atmel_spi_one_transfer(struct spi_master *master, struct atmel_spi_device *asd; int timeout; int ret; + unsigned long dma_timeout; as = spi_master_get_devdata(master); @@ -1103,15 +1104,12 @@ static int atmel_spi_one_transfer(struct spi_master *master, /* interrupts are disabled, so free the lock for schedule */ atmel_spi_unlock(as); - ret = wait_for_completion_timeout(&as->xfer_completion, - SPI_DMA_TIMEOUT); + dma_timeout = wait_for_completion_timeout(&as->xfer_completion, + SPI_DMA_TIMEOUT); atmel_spi_lock(as); - if (WARN_ON(ret == 0)) { - dev_err(&spi->dev, - "spi trasfer timeout, err %d\n", ret); + if (WARN_ON(dma_timeout == 0)) { + dev_err(&spi->dev, "spi transfer timeout\n"); as->done_status = -EIO; - } else { - ret = 0; } if (as->done_status) diff --git a/drivers/spi/spi-au1550.c b/drivers/spi/spi-au1550.c index 326f47973684..f45e085c01a6 100644 --- a/drivers/spi/spi-au1550.c +++ b/drivers/spi/spi-au1550.c @@ -15,10 +15,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include <linux/init.h> diff --git a/drivers/spi/spi-bcm2835.c b/drivers/spi/spi-bcm2835.c index 98aab457b24d..419a782ab6d5 100644 --- a/drivers/spi/spi-bcm2835.c +++ b/drivers/spi/spi-bcm2835.c @@ -17,10 +17,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */ #include <linux/clk.h> diff --git a/drivers/spi/spi-bcm63xx.c b/drivers/spi/spi-bcm63xx.c index c20530982e26..e73e2b052c9c 100644 --- a/drivers/spi/spi-bcm63xx.c +++ b/drivers/spi/spi-bcm63xx.c @@ -13,10 +13,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the - * Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, */ #include <linux/kernel.h> diff --git a/drivers/spi/spi-bitbang.c b/drivers/spi/spi-bitbang.c index dc7d2c2d643e..5ef6638d5e8a 100644 --- a/drivers/spi/spi-bitbang.c +++ b/drivers/spi/spi-bitbang.c @@ -10,10 +10,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include <linux/spinlock.h> diff --git a/drivers/spi/spi-butterfly.c b/drivers/spi/spi-butterfly.c index ee4f91ccd8fd..9a95862986c8 100644 --- a/drivers/spi/spi-butterfly.c +++ b/drivers/spi/spi-butterfly.c @@ -12,10 +12,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ #include <linux/kernel.h> #include <linux/init.h> diff --git a/drivers/spi/spi-coldfire-qspi.c b/drivers/spi/spi-coldfire-qspi.c index 41b5dc4445f6..688956ff5095 100644 --- a/drivers/spi/spi-coldfire-qspi.c +++ b/drivers/spi/spi-coldfire-qspi.c @@ -12,11 +12,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA - * */ #include <linux/kernel.h> diff --git a/drivers/spi/spi-davinci.c b/drivers/spi/spi-davinci.c index b3707badb1e5..5e991065f5b0 100644 --- a/drivers/spi/spi-davinci.c +++ b/drivers/spi/spi-davinci.c @@ -11,10 +11,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include <linux/interrupt.h> diff --git a/drivers/spi/spi-dln2.c b/drivers/spi/spi-dln2.c new file mode 100644 index 000000000000..3b7d91d94fea --- /dev/null +++ b/drivers/spi/spi-dln2.c @@ -0,0 +1,881 @@ +/* + * Driver for the Diolan DLN-2 USB-SPI adapter + * + * Copyright (c) 2014 Intel Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation, version 2. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/mfd/dln2.h> +#include <linux/spi/spi.h> +#include <linux/pm_runtime.h> +#include <asm/unaligned.h> + +#define DLN2_SPI_MODULE_ID 0x02 +#define DLN2_SPI_CMD(cmd) DLN2_CMD(cmd, DLN2_SPI_MODULE_ID) + +/* SPI commands */ +#define DLN2_SPI_GET_PORT_COUNT DLN2_SPI_CMD(0x00) +#define DLN2_SPI_ENABLE DLN2_SPI_CMD(0x11) +#define DLN2_SPI_DISABLE DLN2_SPI_CMD(0x12) +#define DLN2_SPI_IS_ENABLED DLN2_SPI_CMD(0x13) +#define DLN2_SPI_SET_MODE DLN2_SPI_CMD(0x14) +#define DLN2_SPI_GET_MODE DLN2_SPI_CMD(0x15) +#define DLN2_SPI_SET_FRAME_SIZE DLN2_SPI_CMD(0x16) +#define DLN2_SPI_GET_FRAME_SIZE DLN2_SPI_CMD(0x17) +#define DLN2_SPI_SET_FREQUENCY DLN2_SPI_CMD(0x18) +#define DLN2_SPI_GET_FREQUENCY DLN2_SPI_CMD(0x19) +#define DLN2_SPI_READ_WRITE DLN2_SPI_CMD(0x1A) +#define DLN2_SPI_READ DLN2_SPI_CMD(0x1B) +#define DLN2_SPI_WRITE DLN2_SPI_CMD(0x1C) +#define DLN2_SPI_SET_DELAY_BETWEEN_SS DLN2_SPI_CMD(0x20) +#define DLN2_SPI_GET_DELAY_BETWEEN_SS DLN2_SPI_CMD(0x21) +#define DLN2_SPI_SET_DELAY_AFTER_SS DLN2_SPI_CMD(0x22) +#define DLN2_SPI_GET_DELAY_AFTER_SS DLN2_SPI_CMD(0x23) +#define DLN2_SPI_SET_DELAY_BETWEEN_FRAMES DLN2_SPI_CMD(0x24) +#define DLN2_SPI_GET_DELAY_BETWEEN_FRAMES DLN2_SPI_CMD(0x25) +#define DLN2_SPI_SET_SS DLN2_SPI_CMD(0x26) +#define DLN2_SPI_GET_SS DLN2_SPI_CMD(0x27) +#define DLN2_SPI_RELEASE_SS DLN2_SPI_CMD(0x28) +#define DLN2_SPI_SS_VARIABLE_ENABLE DLN2_SPI_CMD(0x2B) +#define DLN2_SPI_SS_VARIABLE_DISABLE DLN2_SPI_CMD(0x2C) +#define DLN2_SPI_SS_VARIABLE_IS_ENABLED DLN2_SPI_CMD(0x2D) +#define DLN2_SPI_SS_AAT_ENABLE DLN2_SPI_CMD(0x2E) +#define DLN2_SPI_SS_AAT_DISABLE DLN2_SPI_CMD(0x2F) +#define DLN2_SPI_SS_AAT_IS_ENABLED DLN2_SPI_CMD(0x30) +#define DLN2_SPI_SS_BETWEEN_FRAMES_ENABLE DLN2_SPI_CMD(0x31) +#define DLN2_SPI_SS_BETWEEN_FRAMES_DISABLE DLN2_SPI_CMD(0x32) +#define DLN2_SPI_SS_BETWEEN_FRAMES_IS_ENABLED DLN2_SPI_CMD(0x33) +#define DLN2_SPI_SET_CPHA DLN2_SPI_CMD(0x34) +#define DLN2_SPI_GET_CPHA DLN2_SPI_CMD(0x35) +#define DLN2_SPI_SET_CPOL DLN2_SPI_CMD(0x36) +#define DLN2_SPI_GET_CPOL DLN2_SPI_CMD(0x37) +#define DLN2_SPI_SS_MULTI_ENABLE DLN2_SPI_CMD(0x38) +#define DLN2_SPI_SS_MULTI_DISABLE DLN2_SPI_CMD(0x39) +#define DLN2_SPI_SS_MULTI_IS_ENABLED DLN2_SPI_CMD(0x3A) +#define DLN2_SPI_GET_SUPPORTED_MODES DLN2_SPI_CMD(0x40) +#define DLN2_SPI_GET_SUPPORTED_CPHA_VALUES DLN2_SPI_CMD(0x41) +#define DLN2_SPI_GET_SUPPORTED_CPOL_VALUES DLN2_SPI_CMD(0x42) +#define DLN2_SPI_GET_SUPPORTED_FRAME_SIZES DLN2_SPI_CMD(0x43) +#define DLN2_SPI_GET_SS_COUNT DLN2_SPI_CMD(0x44) +#define DLN2_SPI_GET_MIN_FREQUENCY DLN2_SPI_CMD(0x45) +#define DLN2_SPI_GET_MAX_FREQUENCY DLN2_SPI_CMD(0x46) +#define DLN2_SPI_GET_MIN_DELAY_BETWEEN_SS DLN2_SPI_CMD(0x47) +#define DLN2_SPI_GET_MAX_DELAY_BETWEEN_SS DLN2_SPI_CMD(0x48) +#define DLN2_SPI_GET_MIN_DELAY_AFTER_SS DLN2_SPI_CMD(0x49) +#define DLN2_SPI_GET_MAX_DELAY_AFTER_SS DLN2_SPI_CMD(0x4A) +#define DLN2_SPI_GET_MIN_DELAY_BETWEEN_FRAMES DLN2_SPI_CMD(0x4B) +#define DLN2_SPI_GET_MAX_DELAY_BETWEEN_FRAMES DLN2_SPI_CMD(0x4C) + +#define DLN2_SPI_MAX_XFER_SIZE 256 +#define DLN2_SPI_BUF_SIZE (DLN2_SPI_MAX_XFER_SIZE + 16) +#define DLN2_SPI_ATTR_LEAVE_SS_LOW BIT(0) +#define DLN2_TRANSFERS_WAIT_COMPLETE 1 +#define DLN2_TRANSFERS_CANCEL 0 +#define DLN2_RPM_AUTOSUSPEND_TIMEOUT 2000 + +struct dln2_spi { + struct platform_device *pdev; + struct spi_master *master; + u8 port; + + /* + * This buffer will be used mainly for read/write operations. Since + * they're quite large, we cannot use the stack. Protection is not + * needed because all SPI communication is serialized by the SPI core. + */ + void *buf; + + u8 bpw; + u32 speed; + u16 mode; + u8 cs; +}; + +/* + * Enable/Disable SPI module. The disable command will wait for transfers to + * complete first. + */ +static int dln2_spi_enable(struct dln2_spi *dln2, bool enable) +{ + u16 cmd; + struct { + u8 port; + u8 wait_for_completion; + } tx; + unsigned len = sizeof(tx); + + tx.port = dln2->port; + + if (enable) { + cmd = DLN2_SPI_ENABLE; + len -= sizeof(tx.wait_for_completion); + } else { + tx.wait_for_completion = DLN2_TRANSFERS_WAIT_COMPLETE; + cmd = DLN2_SPI_DISABLE; + } + + return dln2_transfer_tx(dln2->pdev, cmd, &tx, len); +} + +/* + * Select/unselect multiple CS lines. The selected lines will be automatically + * toggled LOW/HIGH by the board firmware during transfers, provided they're + * enabled first. + * + * Ex: cs_mask = 0x03 -> CS0 & CS1 will be selected and the next WR/RD operation + * will toggle the lines LOW/HIGH automatically. + */ +static int dln2_spi_cs_set(struct dln2_spi *dln2, u8 cs_mask) +{ + struct { + u8 port; + u8 cs; + } tx; + + tx.port = dln2->port; + + /* + * According to Diolan docs, "a slave device can be selected by changing + * the corresponding bit value to 0". The rest must be set to 1. Hence + * the bitwise NOT in front. + */ + tx.cs = ~cs_mask; + + return dln2_transfer_tx(dln2->pdev, DLN2_SPI_SET_SS, &tx, sizeof(tx)); +} + +/* + * Select one CS line. The other lines will be un-selected. + */ +static int dln2_spi_cs_set_one(struct dln2_spi *dln2, u8 cs) +{ + return dln2_spi_cs_set(dln2, BIT(cs)); +} + +/* + * Enable/disable CS lines for usage. The module has to be disabled first. + */ +static int dln2_spi_cs_enable(struct dln2_spi *dln2, u8 cs_mask, bool enable) +{ + struct { + u8 port; + u8 cs; + } tx; + u16 cmd; + + tx.port = dln2->port; + tx.cs = cs_mask; + cmd = enable ? DLN2_SPI_SS_MULTI_ENABLE : DLN2_SPI_SS_MULTI_DISABLE; + + return dln2_transfer_tx(dln2->pdev, cmd, &tx, sizeof(tx)); +} + +static int dln2_spi_cs_enable_all(struct dln2_spi *dln2, bool enable) +{ + u8 cs_mask = GENMASK(dln2->master->num_chipselect - 1, 0); + + return dln2_spi_cs_enable(dln2, cs_mask, enable); +} + +static int dln2_spi_get_cs_num(struct dln2_spi *dln2, u16 *cs_num) +{ + int ret; + struct { + u8 port; + } tx; + struct { + __le16 cs_count; + } rx; + unsigned rx_len = sizeof(rx); + + tx.port = dln2->port; + ret = dln2_transfer(dln2->pdev, DLN2_SPI_GET_SS_COUNT, &tx, sizeof(tx), + &rx, &rx_len); + if (ret < 0) + return ret;</ |