diff options
45 files changed, 5837 insertions, 256 deletions
diff --git a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt index 21055e210234..c1359f4d48d7 100644 --- a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt @@ -46,6 +46,10 @@ Required properties: 0 maps to GPMC_WAIT0 pin. - gpio-cells: Must be set to 2 +Required properties when using NAND prefetch dma: + - dmas GPMC NAND prefetch dma channel + - dma-names Must be set to "rxtx" + Timing properties for child nodes. All are optional and default to 0. - gpmc,sync-clk-ps: Minimum clock period for synchronous mode, in picoseconds @@ -137,7 +141,8 @@ Example for an AM33xx board: ti,hwmods = "gpmc"; reg = <0x50000000 0x2000>; interrupts = <100>; - + dmas = <&edma 52 0>; + dma-names = "rxtx"; gpmc,num-cs = <8>; gpmc,num-waitpins = <2>; #address-cells = <2>; diff --git a/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt b/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt new file mode 100644 index 000000000000..489807005eda --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt @@ -0,0 +1,32 @@ +* Atmel Quad Serial Peripheral Interface (QSPI) + +Required properties: +- compatible: Should be "atmel,sama5d2-qspi". +- reg: Should contain the locations and lengths of the base registers + and the mapped memory. +- reg-names: Should contain the resource reg names: + - qspi_base: configuration register address space + - qspi_mmap: memory mapped address space +- interrupts: Should contain the interrupt for the device. +- clocks: The phandle of the clock needed by the QSPI controller. +- #address-cells: Should be <1>. +- #size-cells: Should be <0>. + +Example: + +spi@f0020000 { + compatible = "atmel,sama5d2-qspi"; + reg = <0xf0020000 0x100>, <0xd0000000 0x8000000>; + reg-names = "qspi_base", "qspi_mmap"; + interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>; + clocks = <&spi0_clk>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0_default>; + status = "okay"; + + m25p80@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt index 7066597c9a81..b40f3a492800 100644 --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt @@ -27,6 +27,7 @@ Required properties: brcm,brcmnand-v6.2 brcm,brcmnand-v7.0 brcm,brcmnand-v7.1 + brcm,brcmnand-v7.2 brcm,brcmnand - reg : the register start and length for NAND register region. (optional) Flash DMA register range (if present) diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt new file mode 100644 index 000000000000..f248056da24c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt @@ -0,0 +1,56 @@ +* Cadence Quad SPI controller + +Required properties: +- compatible : Should be "cdns,qspi-nor". +- reg : Contains two entries, each of which is a tuple consisting of a + physical address and length. The first entry is the address and + length of the controller register set. The second entry is the + address and length of the QSPI Controller data area. +- interrupts : Unit interrupt specifier for the controller interrupt. +- clocks : phandle to the Quad SPI clock. +- cdns,fifo-depth : Size of the data FIFO in words. +- cdns,fifo-width : Bus width of the data FIFO in bytes. +- cdns,trigger-address : 32-bit indirect AHB trigger address. + +Optional properties: +- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not. + +Optional subnodes: +Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional +custom properties: +- cdns,read-delay : Delay for read capture logic, in clock cycles +- cdns,tshsl-ns : Delay in nanoseconds for the length that the master + mode chip select outputs are de-asserted between + transactions. +- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being + de-activated and the activation of another. +- cdns,tchsh-ns : Delay in nanoseconds between last bit of current + transaction and deasserting the device chip select + (qspi_n_ss_out). +- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low + and first bit transfer. + +Example: + + qspi: spi@ff705000 { + compatible = "cdns,qspi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xff705000 0x1000>, + <0xffa00000 0x1000>; + interrupts = <0 151 4>; + clocks = <&qspi_clk>; + cdns,is-decoded-cs; + cdns,fifo-depth = <128>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x00000000>; + + flash0: n25q00@0 { + ... + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index 3ee7e202657c..174f68c26c1b 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -39,7 +39,7 @@ Optional properties: "prefetch-polled" Prefetch polled mode (default) "polled" Polled mode, without prefetch - "prefetch-dma" Prefetch enabled sDMA mode + "prefetch-dma" Prefetch enabled DMA mode "prefetch-irq" Prefetch enabled irq mode - elm_id: <deprecated> use "ti,elm-id" instead diff --git a/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt b/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt new file mode 100644 index 000000000000..74981520d6dd --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt @@ -0,0 +1,24 @@ +HiSilicon SPI-NOR Flash Controller + +Required properties: +- compatible : Should be "hisilicon,fmc-spi-nor" and one of the following strings: + "hisilicon,hi3519-spi-nor" +- address-cells : Should be 1. +- size-cells : Should be 0. +- reg : Offset and length of the register set for the controller device. +- reg-names : Must include the following two entries: "control", "memory". +- clocks : handle to spi-nor flash controller clock. + +Example: +spi-nor-controller@10000000 { + compatible = "hisilicon,hi3519-spi-nor", "hisilicon,fmc-spi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10000000 0x1000>, <0x14000000 0x1000000>; + reg-names = "control", "memory"; + clocks = <&clock HI3519_FMC_CLK>; + spi-nor@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt new file mode 100644 index 000000000000..069c192ed5c2 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt @@ -0,0 +1,160 @@ +MTK SoCs NAND FLASH controller (NFC) DT binding + +This file documents the device tree bindings for MTK SoCs NAND controllers. +The functional split of the controller requires two drivers to operate: +the nand controller interface driver and the ECC engine driver. + +The hardware description for both devices must be captured as device +tree nodes. + +1) NFC NAND Controller Interface (NFI): +======================================= + +The first part of NFC is NAND Controller Interface (NFI) HW. +Required NFI properties: +- compatible: Should be "mediatek,mtxxxx-nfc". +- reg: Base physical address and size of NFI. +- interrupts: Interrupts of NFI. +- clocks: NFI required clocks. +- clock-names: NFI clocks internal name. +- status: Disabled default. Then set "okay" by platform. +- ecc-engine: Required ECC Engine node. +- #address-cells: NAND chip index, should be 1. +- #size-cells: Should be 0. + +Example: + + nandc: nfi@1100d000 { + compatible = "mediatek,mt2701-nfc"; + reg = <0 0x1100d000 0 0x1000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI>, + <&pericfg CLK_PERI_NFI_PAD>; + clock-names = "nfi_clk", "pad_clk"; + status = "disabled"; + ecc-engine = <&bch>; + #address-cells = <1>; + #size-cells = <0>; + }; + +Platform related properties, should be set in {platform_name}.dts: +- children nodes: NAND chips. + +Children nodes properties: +- reg: Chip Select Signal, default 0. + Set as reg = <0>, <1> when need 2 CS. +Optional: +- nand-on-flash-bbt: Store BBT on NAND Flash. +- nand-ecc-mode: the NAND ecc mode (check driver for supported modes) +- nand-ecc-step-size: Number of data bytes covered by a single ECC step. + valid values: 512 and 1024. + 1024 is recommended for large page NANDs. +- nand-ecc-strength: Number of bits to correct per ECC step. + The valid values that the controller supports are: 4, 6, + 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, 40, 44, + 48, 52, 56, 60. + The strength should be calculated as follows: + E = (S - F) * 8 / 14 + S = O / (P / Q) + E : nand-ecc-strength. + S : spare size per sector. + F : FDM size, should be in the range [1,8]. + It is used to store free oob data. + O : oob size. + P : page size. + Q : nand-ecc-step-size. + If the result does not match any one of the listed + choices above, please select the smaller valid value from + the list. + (otherwise the driver will do the adjustment at runtime) +- pinctrl-names: Default NAND pin GPIO setting name. +- pinctrl-0: GPIO setting node. + +Example: + &pio { + nand_pins_default: nanddefault { + pins_dat { + pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>, + <MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>, + <MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>, + <MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>, + <MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>, + <MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>, + <MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>, + <MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>, + <MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>; + input-enable; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-up; + }; + + pins_we { + pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-up = <MTK_PUPD_SET_R1R0_10>; + }; + + pins_ale { + pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>; + drive-strength = <MTK_DRIVE_8mA>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + }; + }; + + &nandc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins_default>; + nand@0 { + reg = <0>; + nand-on-flash-bbt; + nand-ecc-mode = "hw"; + nand-ecc-strength = <24>; + nand-ecc-step-size = <1024>; + }; + }; + +NAND chip optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + preloader@0 { + label = "pl"; + read-only; + reg = <0x00000000 0x00400000>; + }; + android@0x00400000 { + label = "android"; + reg = <0x00400000 0x12c00000>; + }; + }; + }; + +2) ECC Engine: +============== + +Required BCH properties: +- compatible: Should be "mediatek,mtxxxx-ecc". +- reg: Base physical address and size of ECC. +- interrupts: Interrupts of ECC. +- clocks: ECC required clocks. +- clock-names: ECC clocks internal name. +- status: Disabled default. Then set "okay" by platform. + +Example: + + bch: ecc@1100e000 { + compatible = "mediatek,mt2701-ecc"; + reg = <0 0x1100e000 0 0x1000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI_ECC>; + clock-names = "nfiecc_clk"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt index 086d6f44c4b9..f322f56aef74 100644 --- a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt @@ -11,10 +11,16 @@ Required properties: * "ahb" : AHB gating clock * "mod" : nand controller clock +Optional properties: +- dmas : shall reference DMA channel associated to the NAND controller. +- dma-names : shall be "rxtx". + Optional children nodes: Children nodes represent the available nand chips. Optional properties: +- reset : phandle + reset specifier pair +- reset-names : must contain "ahb" - allwinner,rb : shall contain the native Ready/Busy ids. or - rb-gpios : shall contain the gpios used as R/B pins. diff --git a/arch/cris/arch-v10/drivers/axisflashmap.c b/arch/cris/arch-v10/drivers/axisflashmap.c index 60d57c590032..bdc25aa43468 100644 --- a/arch/cris/arch-v10/drivers/axisflashmap.c +++ b/arch/cris/arch-v10/drivers/axisflashmap.c @@ -397,7 +397,7 @@ static int __init init_axis_flash(void) if (!romfs_in_flash) { /* Create an RAM device for the root partition (romfs). */ -#if !defined(CONFIG_MTD_MTDRAM) || (CONFIG_MTDRAM_TOTAL_SIZE != 0) || (CONFIG_MTDRAM_ABS_POS != 0) +#if !defined(CONFIG_MTD_MTDRAM) || (CONFIG_MTDRAM_TOTAL_SIZE != 0) /* No use trying to boot this kernel from RAM. Panic! */ printk(KERN_EMERG "axisflashmap: Cannot create an MTD RAM " "device due to kernel (mis)configuration!\n"); diff --git a/arch/cris/arch-v32/drivers/axisflashmap.c b/arch/cris/arch-v32/drivers/axisflashmap.c index bd10d3ba0949..87656c41fec7 100644 --- a/arch/cris/arch-v32/drivers/axisflashmap.c +++ b/arch/cris/arch-v32/drivers/axisflashmap.c @@ -320,7 +320,7 @@ static int __init init_axis_flash(void) * but its size must be configured as 0 so as not to conflict * with our usage. */ -#if !defined(CONFIG_MTD_MTDRAM) || (CONFIG_MTDRAM_TOTAL_SIZE != 0) || (CONFIG_MTDRAM_ABS_POS != 0) +#if !defined(CONFIG_MTD_MTDRAM) || (CONFIG_MTDRAM_TOTAL_SIZE != 0) if (!romfs_in_flash && !nand_boot) { printk(KERN_EMERG "axisflashmap: Cannot create an MTD RAM " "device; configure CONFIG_MTD_MTDRAM with size = 0!\n"); diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig index 133712346911..4b4c0c3c3d2f 100644 --- a/drivers/memory/Kconfig +++ b/drivers/memory/Kconfig @@ -115,7 +115,7 @@ config FSL_CORENET_CF config FSL_IFC bool - depends on FSL_SOC + depends on FSL_SOC || ARCH_LAYERSCAPE config JZ4780_NEMC bool "Ingenic JZ4780 SoC NEMC driver" diff --git a/drivers/memory/fsl_ifc.c b/drivers/memory/fsl_ifc.c index 904b4af5f142..1b182b117f9c 100644 --- a/drivers/memory/fsl_ifc.c +++ b/drivers/memory/fsl_ifc.c @@ -31,7 +31,9 @@ #include <linux/of_device.h> #include <linux/platform_device.h> #include <linux/fsl_ifc.h> -#include <asm/prom.h> +#include <linux/irqdomain.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> struct fsl_ifc_ctrl *fsl_ifc_ctrl_dev; EXPORT_SYMBOL(fsl_ifc_ctrl_dev); diff --git a/drivers/mtd/chips/cfi_cmdset_0020.c b/drivers/mtd/chips/cfi_cmdset_0020.c index 9a1a6ffd16b8..94d3eb42c4d5 100644 --- a/drivers/mtd/chips/cfi_cmdset_0020.c +++ b/drivers/mtd/chips/cfi_cmdset_0020.c @@ -416,7 +416,7 @@ static int cfi_staa_read (struct mtd_info *mtd, loff_t from, size_t len, size_t return ret; } -static inline int do_write_buffer(struct map_info *map, struct flchip *chip, +static int do_write_buffer(struct map_info *map, struct flchip *chip, unsigned long adr, const u_char *buf, int len) { struct cfi_private *cfi = map->fldrv_priv; diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig index 64a248556d29..58329d2dacd1 100644 --- a/drivers/mtd/devices/Kconfig +++ b/drivers/mtd/devices/Kconfig @@ -113,12 +113,12 @@ config MTD_SST25L if you want to specify device partitioning. config MTD_BCM47XXSFLASH - tristate "R/O support for serial flash on BCMA bus" + tristate "Support for serial flash on BCMA bus" depends on BCMA_SFLASH && (MIPS || ARM) help BCMA bus can have various flash memories attached, they are registered by bcma as platform devices. This enables driver for - serial flash memories (only read-only mode is implemented). + serial flash memories. config MTD_SLRAM tristate "Uncached system RAM" @@ -171,18 +171,6 @@ config MTDRAM_ERASE_SIZE as a module, it is also possible to specify this as a parameter when loading the module. -#If not a module (I don't want to test it as a module) -config MTDRAM_ABS_POS - hex "SRAM Hexadecimal Absolute position or 0" - depends on MTD_MTDRAM=y - default "0" - help - If you have system RAM accessible by the CPU but not used by Linux - in normal operation, you can give the physical address at which the - available RAM starts, and the MTDRAM driver will use it instead of - allocating space from Linux's available memory. Otherwise, leave - this set to zero. Most people will want to leave this as zero. - config MTD_BLOCK2MTD tristate "MTD using block device" depends on BLOCK diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c index 9d6854467651..9cf7fcd28034 100644 --- a/drivers/mtd/devices/m25p80.c +++ b/drivers/mtd/devices/m25p80.c @@ -73,14 +73,15 @@ static int m25p80_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len) return spi_write(spi, flash->command, len + 1); } -static void m25p80_write(struct spi_nor *nor, loff_t to, size_t len, - size_t *retlen, const u_char *buf) +static ssize_t m25p80_write(struct spi_nor *nor, loff_t to, size_t len, + const u_char *buf) { struct m25p *flash = nor->priv; struct spi_device *spi = flash->spi; struct spi_transfer t[2] = {}; struct spi_message m; int cmd_sz = m25p_cmdsz(nor); + ssize_t ret; spi_message_init(&m); @@ -98,9 +99,14 @@ static void m25p80_write(struct spi_nor *nor, loff_t to, size_t len, t[1].len = len; spi_message_add_tail(&t[1], &m); - spi_sync(spi, &m); + ret = spi_sync(spi, &m); + if (ret) + return ret; - *retlen += m.actual_length - cmd_sz; + ret = m.actual_length - cmd_sz; + if (ret < 0) + return -EIO; + return ret; } static inline unsigned int m25p80_rx_nbits(struct spi_nor *nor) @@ -119,21 +125,21 @@ static inline unsigned int m25p80_rx_nbits(struct spi_nor *nor) * Read an address range from the nor chip. The address range * may be any size provided it is within the physical boundaries. */ -static int m25p80_read(struct spi_nor *nor, loff_t from, size_t len, - size_t *retlen, u_char *buf) +static ssize_t m25p80_read(struct spi_nor *nor, loff_t from, size_t len, + u_char *buf) { struct m25p *flash = nor->priv; struct spi_device *spi = flash->spi; struct spi_transfer t[2]; struct spi_message m; unsigned int dummy = nor->read_dummy; + ssize_t ret; /* convert the dummy cycles to the number of bytes */ dummy /= 8; if (spi_flash_read_supported(spi)) { struct spi_flash_read_message msg; - int ret; memset(&msg, 0, sizeof(msg)); @@ -149,8 +155,9 @@ static int m25p80_read(struct spi_nor *nor, loff_t from, size_t len, msg.data_nbits = m25p80_rx_nbits(nor); ret = spi_flash_read(spi, &msg); - *retlen = msg.retlen; - return ret; + if (ret < 0) + return ret; + return msg.retlen; } spi_message_init(&m); @@ -165,13 +172,17 @@ static int m25p80_read(struct spi_nor *nor, loff_t from, size_t len, t[1].rx_buf = buf; t[1].rx_nbits = m25p80_rx_nbits(nor); - t[1].len = len; + t[1].len = min(len, spi_max_transfer_size(spi)); spi_message_add_tail(&t[1], &m); - spi_sync(spi, &m); + ret = spi_sync(spi, &m); + if (ret) + return ret; - *retlen = m.actual_length - m25p_cmdsz(nor) - dummy; - return 0; + ret = m.actual_length - m25p_cmdsz(nor) - dummy; + if (ret < 0) + return -EIO; + return ret; } /* diff --git a/drivers/mtd/maps/physmap_of.c b/drivers/mtd/maps/physmap_of.c index 22f3858c0364..3fad35942895 100644 --- a/drivers/mtd/maps/physmap_of.c +++ b/drivers/mtd/maps/physmap_of.c @@ -186,7 +186,7 @@ static int of_flash_probe(struct platform_device *dev) * consists internally of 2 non-identical NOR chips on one die. */ p = of_get_property(dp, "reg", &count); - if (count % reg_tuple_size != 0) { + if (!p || count % reg_tuple_size != 0) { dev_err(&dev->dev, "Malformed reg property on %s\n", dev->dev.of_node->full_name); err = -EINVAL; diff --git a/drivers/mtd/maps/pmcmsp-flash.c b/drivers/mtd/maps/pmcmsp-flash.c index 744ca5cacc9b..f9fa3fad728e 100644 --- a/drivers/mtd/maps/pmcmsp-flash.c +++ b/drivers/mtd/maps/pmcmsp-flash.c @@ -75,15 +75,15 @@ static int __init init_msp_flash(void) printk(KERN_NOTICE "Found %d PMC flash devices\n", fcnt); - msp_flash = kmalloc(fcnt * sizeof(struct map_info *), GFP_KERNEL); + msp_flash = kcalloc(fcnt, sizeof(*msp_flash), GFP_KERNEL); if (!msp_flash) return -ENOMEM; - msp_parts = kmalloc(fcnt * sizeof(struct mtd_partition *), GFP_KERNEL); + msp_parts = kcalloc(fcnt, sizeof(*msp_parts), GFP_KERNEL); if (!msp_parts) goto free_msp_flash; - msp_maps = kcalloc(fcnt, sizeof(struct mtd_info), GFP_KERNEL); + msp_maps = kcalloc(fcnt, sizeof(*msp_maps), GFP_KERNEL); if (!msp_maps) goto free_msp_parts; diff --git a/drivers/mtd/maps/sa1100-flash.c b/drivers/mtd/maps/sa1100-flash.c index 142fc3d79463..784c6e1a0391 100644 --- a/drivers/mtd/maps/sa1100-flash.c +++ b/drivers/mtd/maps/sa1100-flash.c @@ -230,8 +230,10 @@ static struct sa_info *sa1100_setup_mtd(struct platform_device *pdev, info->mtd = mtd_concat_create(cdev, info->num_subdev, plat->name); - if (info->mtd == NULL) + if (info->mtd == NULL) { ret = -ENXIO; + goto err; + } } info->mtd->dev.parent = &pdev->dev; diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index f05e0e9eb2f7..21ff58099f3b 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -438,7 +438,7 @@ config MTD_NAND_FSL_ELBC config MTD_NAND_FSL_IFC tristate "NAND support for Freescale IFC controller" - depends on MTD_NAND && FSL_SOC + depends on MTD_NAND && (FSL_SOC || ARCH_LAYERSCAPE) select FSL_IFC select MEMORY help @@ -539,7 +539,6 @@ config MTD_NAND_FSMC config MTD_NAND_XWAY tristate "Support for NAND on Lantiq XWAY SoC" depends on LANTIQ && SOC_TYPE_XWAY - select MTD_NAND_PLATFORM help Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached to the External Bus Unit (EBU). @@ -563,4 +562,11 @@ config MTD_NAND_QCOM Enables support for NAND flash chips on SoCs containing the EBI2 NAND controller. This controller is found on IPQ806x SoC. +config MTD_NAND_MTK + tristate "Support for NAND controller on MTK SoCs" + depends on HAS_DMA + help + Enables support for NAND controller on MTK SoCs. + This controller is found on mt27xx, mt81xx, mt65xx SoCs. + endif # MTD_NAND diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index f55335373f7c..cafde6f3d957 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -57,5 +57,6 @@ obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_nand.o obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/ obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o +obj-$(CONFIG_MTD_NAND_MTK) += mtk_nand.o mtk_ecc.o nand-objs := nand_base.o nand_bbt.o nand_timings.o diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/brcmnand/brcmnand.c index b76ad7c0144f..8eb2c64df38c 100644 --- a/drivers/mtd/nand/brcmnand/brcmnand.c +++ b/drivers/mtd/nand/brcmnand/brcmnand.c @@ -340,6 +340,36 @@ static const u |