diff options
113 files changed, 18261 insertions, 843 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-atlas7.txt b/Documentation/devicetree/bindings/gpio/gpio-atlas7.txt new file mode 100644 index 000000000000..d7e123fc90b5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-atlas7.txt @@ -0,0 +1,50 @@ +CSR SiRFatlas7 GPIO controller bindings + +Required properties: +- compatible : "sirf,atlas7-gpio" +- reg : Address range of the pinctrl registers +- interrupts : Interrupts used by every GPIO group +- gpio-banks : How many gpio banks on this controller +- gpio-controller : Indicates this device is a GPIO controller +- interrupt-controller : Marks the device node as an interrupt controller + +The GPIO controller also acts as an interrupt controller. It uses the default +two cells specifier as described in Documentation/devicetree/bindings/ +interrupt-controller/interrupts.txt. + +Example: + + gpio_0: gpio_mediam@17040000 { + compatible = "sirf,atlas7-gpio"; + reg = <0x17040000 0x1000>; + interrupts = <0 13 0>, <0 14 0>; + + #gpio-cells = <2>; + #interrupt-cells = <2>; + + gpio-controller; + interrupt-controller; + + gpio-banks = <2>; + gpio-ranges = <&pinctrl 0 0 0>, + <&pinctrl 32 0 0>; + gpio-ranges-group-names = "lvds_gpio_grp", + "uart_nand_gpio_grp"; + }; + + leds { + compatible = "gpio-leds"; + + led1 { + gpios = <&gpio_1 15 0>; + ... + }; + + led2 { + gpios = <&gpio_2 34 0>; + ... + }; + }; + +Please refer to gpio.txt in this directory for details of the common +gpio properties used by devices. diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index fdd8046e650a..9462ab7ddd1f 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -16,6 +16,8 @@ Required properties: "allwinner,sun7i-a20-pinctrl" "allwinner,sun8i-a23-pinctrl" "allwinner,sun8i-a23-r-pinctrl" + "allwinner,sun8i-a33-pinctrl" + - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt new file mode 100644 index 000000000000..08a4a32c8eb0 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt @@ -0,0 +1,217 @@ +Imagination Technologies Pistachio SoC pin controllers +====================================================== + +The pin controllers on Pistachio are a combined GPIO controller, (GPIO) +interrupt controller, and pinmux + pinconf device. The system ("east") pin +controller on Pistachio has 99 pins, 90 of which are MFIOs which can be +configured as GPIOs. The 90 GPIOs are divided into 6 banks of up to 16 GPIOs +each. The GPIO banks are represented as sub-nodes of the pad controller node. + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +Required properties for pin controller node: +-------------------------------------------- + - compatible: "img,pistachio-system-pinctrl". + - reg: Address range of the pinctrl registers. + +Required properties for GPIO bank sub-nodes: +-------------------------------------------- + - interrupts: Interrupt line for the GPIO bank. + - gpio-controller: Indicates the device is a GPIO controller. + - #gpio-cells: Must be two. The first cell is the GPIO pin number and the + second cell indicates the polarity. See <dt-bindings/gpio/gpio.h> for + a list of possible values. + - interrupt-controller: Indicates the device is an interrupt controller. + - #interrupt-cells: Must be two. The first cell is the GPIO pin number and + the second cell encodes the interrupt flags. See + <dt-bindings/interrupt-controller/irq.h> for a list of valid flags. + +Note that the N GPIO bank sub-nodes *must* be named gpio0, gpio1, ... gpioN-1. + +Required properties for pin configuration sub-nodes: +---------------------------------------------------- + - pins: List of pins to which the configuration applies. See below for a + list of possible pins. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - function: Mux function for the specified pins. This is not applicable for + non-MFIO pins. See below for a list of valid functions for each pin. + - bias-high-impedance: Enable high-impedance mode. + - bias-pull-up: Enable weak pull-up. + - bias-pull-down: Enable weak pull-down. + - bias-bus-hold: Enable bus-keeper mode. + - drive-strength: Drive strength in mA. Supported values: 2, 4, 8, 12. + - input-schmitt-enable: Enable Schmitt trigger. + - input-schmitt-disable: Disable Schmitt trigger. + - slew-rate: Slew rate control. 0 for slow, 1 for fast. + +Pin Functions +--- --------- +mfio0 spim1 +mfio1 spim1, spim0, uart1 +mfio2 spim1, spim0, uart1 +mfio3 spim1 +mfio4 spim1 +mfio5 spim1 +mfio6 spim1 +mfio7 spim1 +mfio8 spim0 +mfio9 spim0 +mfio10 spim0 +mfio11 spis +mfio12 spis +mfio13 spis +mfio14 spis +mfio15 sdhost, mips_trace_clk, mips_trace_data +mfio16 sdhost, mips_trace_dint, mips_trace_data +mfio17 sdhost, mips_trace_trigout, mips_trace_data +mfio18 sdhost, mips_trace_trigin, mips_trace_data +mfio19 sdhost, mips_trace_dm, mips_trace_data +mfio20 sdhost, mips_trace_probe_n, mips_trace_data +mfio21 sdhost, mips_trace_data +mfio22 sdhost, mips_trace_data +mfio23 sdhost +mfio24 sdhost +mfio25 sdhost +mfio26 sdhost +mfio27 sdhost +mfio28 i2c0, spim0 +mfio29 i2c0, spim0 +mfio30 i2c1, spim0 +mfio31 i2c1, spim1 +mfio32 i2c2 +mfio33 i2c2 +mfio34 i2c3 +mfio35 i2c3 +mfio36 i2s_out, audio_clk_in +mfio37 i2s_out, debug_raw_cca_ind +mfio38 i2s_out, debug_ed_sec20_cca_ind +mfio39 i2s_out, debug_ed_sec40_cca_ind +mfio40 i2s_out, debug_agc_done_0 +mfio41 i2s_out, debug_agc_done_1 +mfio42 i2s_out, debug_ed_cca_ind +mfio43 i2s_out, debug_s2l_done +mfio44 i2s_out +mfio45 i2s_dac_clk, audio_sync +mfio46 audio_trigger +mfio47 i2s_in +mfio48 i2s_in +mfio49 i2s_in +mfio50 i2s_in +mfio51 i2s_in +mfio52 i2s_in +mfio53 i2s_in +mfio54 i2s_in, spdif_in +mfio55 uart0, spim0, spim1 +mfio56 uart0, spim0, spim1 +mfio57 uart0, spim0, spim1 +mfio58 uart0, spim1 +mfio59 uart1 +mfio60 uart1 +mfio61 spdif_out +mfio62 spdif_in +mfio63 eth, mips_trace_clk, mips_trace_data +mfio64 eth, mips_trace_dint, mips_trace_data +mfio65 eth, mips_trace_trigout, mips_trace_data +mfio66 eth, mips_trace_trigin, mips_trace_data +mfio67 eth, mips_trace_dm, mips_trace_data +mfio68 eth, mips_trace_probe_n, mips_trace_data +mfio69 eth, mips_trace_data +mfio70 eth, mips_trace_data +mfio71 eth +mfio72 ir +mfio73 pwmpdm, mips_trace_clk, sram_debug +mfio74 pwmpdm, mips_trace_dint, sram_debug +mfio75 pwmpdm, mips_trace_trigout, rom_debug +mfio76 pwmpdm, mips_trace_trigin, rom_de |