diff options
-rw-r--r-- | drivers/i2c/busses/Kconfig | 3 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-icy.c | 57 |
2 files changed, 60 insertions, 0 deletions
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 8b97ba4a2c0c..ee7f415a625a 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -1320,6 +1320,9 @@ config I2C_ICY This support is also available as a module. If so, the module will be called i2c-icy. + If you have a 2019 edition board with an LTC2990 sensor at address + 0x4c, loading the module 'ltc2990' is sufficient to enable it. + config I2C_MLXCPLD tristate "Mellanox I2C driver" depends on X86_64 diff --git a/drivers/i2c/busses/i2c-icy.c b/drivers/i2c/busses/i2c-icy.c index 0d61936dfc0b..8382eb64b424 100644 --- a/drivers/i2c/busses/i2c-icy.c +++ b/drivers/i2c/busses/i2c-icy.c @@ -53,6 +53,8 @@ struct icy_i2c { void __iomem *reg_s0; void __iomem *reg_s1; + struct fwnode_handle *ltc2990_fwnode; + struct i2c_client *ltc2990_client; }; /* @@ -94,11 +96,34 @@ static void icy_pcf_waitforpin(void *data) /* * Main i2c-icy part */ +static unsigned short const icy_ltc2990_addresses[] = { + 0x4c, 0x4d, 0x4e, 0x4f, I2C_CLIENT_END +}; + +/* + * Additional sensors exposed once this property is applied: + * + * in1 will be the voltage of the 5V rail, divided by 2. + * in2 will be the voltage of the 12V rail, divided by 4. + * temp3 will be measured using a PCB loop next the chip. + */ +static const u32 icy_ltc2990_meas_mode[] = {0, 3}; + +static const struct property_entry icy_ltc2990_props[] = { + PROPERTY_ENTRY_U32_ARRAY("lltc,meas-mode", icy_ltc2990_meas_mode), + { } +}; + static int icy_probe(struct zorro_dev *z, const struct zorro_device_id *ent) { struct icy_i2c *i2c; struct i2c_algo_pcf_data *algo_data; + struct fwnode_handle *new_fwnode; + struct i2c_board_info ltc2990_info = { + .type = "ltc2990", + .addr = 0x4c, + }; i2c = devm_kzalloc(&z->dev, sizeof(*i2c), GFP_KERNEL); if (!i2c) @@ -140,6 +165,35 @@ static int icy_probe(struct zorro_dev *z, dev_info(&z->dev, "ICY I2C controller at %pa, IRQ not implemented\n", &z->resource.start); + /* + * The 2019 a1k.org PCBs have an LTC2990 at 0x4c, so start + * it automatically once ltc2990 is modprobed. + * + * in0 is the voltage of the internal 5V power supply. + * temp1 is the temperature inside the chip. + * + * See property_entry above for in1, in2, temp3. + */ + new_fwnode = fwnode_create_software_node(icy_ltc2990_props, NULL); + if (IS_ERR(new_fwnode)) { + dev_info(&z->dev, "Failed to create fwnode for LTC2990, error: %ld\n", + PTR_ERR(new_fwnode)); + } else { + /* + * Store the fwnode so we can destroy it on .remove(). + * Only store it on success, as fwnode_remove_software_node() + * is NULL safe, but not PTR_ERR safe. + */ + i2c->ltc2990_fwnode = new_fwnode; + ltc2990_info.fwnode = new_fwnode; + + i2c->ltc2990_client = + i2c_new_probed_device(&i2c->adapter, + <c2990_info, + icy_ltc2990_addresses, + NULL); + } + return 0; } @@ -147,6 +201,9 @@ static void icy_remove(struct zorro_dev *z) { struct icy_i2c *i2c = dev_get_drvdata(&z->dev); + i2c_unregister_device(i2c->ltc2990_client); + fwnode_remove_software_node(i2c->ltc2990_fwnode); + i2c_del_adapter(&i2c->adapter); } |