diff options
39 files changed, 3818 insertions, 1474 deletions
diff --git a/Documentation/ABI/testing/sysfs-class-power b/Documentation/ABI/testing/sysfs-class-power index 369d2a2d7d3e..fa05719f9981 100644 --- a/Documentation/ABI/testing/sysfs-class-power +++ b/Documentation/ABI/testing/sysfs-class-power @@ -74,3 +74,61 @@ Description: Valid values: - 0 - 70 (minutes), step by 10 (rounded down) + +What: /sys/class/power_supply/bq24257-charger/ovp_voltage +Date: October 2015 +KernelVersion: 4.4.0 +Contact: Andreas Dannenberg <dannenberg@ti.com> +Description: + This entry configures the overvoltage protection feature of bq24257- + type charger devices. This feature protects the device and other + components against damage from overvoltage on the input supply. See + device datasheet for details. + + Valid values: + - 6000000, 6500000, 7000000, 8000000, 9000000, 9500000, 10000000, + 10500000 (all uV) + +What: /sys/class/power_supply/bq24257-charger/in_dpm_voltage +Date: October 2015 +KernelVersion: 4.4.0 +Contact: Andreas Dannenberg <dannenberg@ti.com> +Description: + This entry configures the input dynamic power path management voltage of + bq24257-type charger devices. Once the supply drops to the configured + voltage, the input current limit is reduced down to prevent the further + drop of the supply. When the IC enters this mode, the charge current is + lower than the set value. See device datasheet for details. + + Valid values: + - 4200000, 4280000, 4360000, 4440000, 4520000, 4600000, 4680000, + 4760000 (all uV) + +What: /sys/class/power_supply/bq24257-charger/high_impedance_enable +Date: October 2015 +KernelVersion: 4.4.0 +Contact: Andreas Dannenberg <dannenberg@ti.com> +Description: + This entry allows enabling the high-impedance mode of bq24257-type + charger devices. If enabled, it places the charger IC into low power + standby mode with the switch mode controller disabled. When disabled, + the charger operates normally. See device datasheet for details. + + Valid values: + - 1: enabled + - 0: disabled + +What: /sys/class/power_supply/bq24257-charger/sysoff_enable +Date: October 2015 +KernelVersion: 4.4.0 +Contact: Andreas Dannenberg <dannenberg@ti.com> +Description: + This entry allows enabling the sysoff mode of bq24257-type charger + devices. If enabled and the input is removed, the internal battery FET + is turned off in order to reduce the leakage from the BAT pin to less + than 1uA. Note that on some devices/systems this disconnects the battery + from the system. See device datasheet for details. + + Valid values: + - 1: enabled + - 0: disabled diff --git a/Documentation/devicetree/bindings/power/bq24257.txt b/Documentation/devicetree/bindings/power/bq24257.txt index 5c9d3940d07c..d693702c9c1e 100644 --- a/Documentation/devicetree/bindings/power/bq24257.txt +++ b/Documentation/devicetree/bindings/power/bq24257.txt @@ -1,21 +1,64 @@ -Binding for TI bq24257 Li-Ion Charger +Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger Required properties: - compatible: Should contain one of the following: + * "ti,bq24250" + * "ti,bq24251" * "ti,bq24257" -- reg: integer, i2c address of the device. +- reg: integer, i2c address of the device. +- interrupt-parent: Should be the phandle for the interrupt controller. Use in + conjunction with "interrupts". +- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in + conjunction with "interrupt-parent". - ti,battery-regulation-voltage: integer, maximum charging voltage in uV. -- ti,charge-current: integer, maximum charging current in uA. -- ti,termination-current: integer, charge will be terminated when current in - constant-voltage phase drops below this value (in uA). +- ti,charge-current: integer, maximum charging current in uA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in uA). + +Optional properties: +- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin. + This pin is not available on all devices however it should be used if + possible as this is the recommended way to obtain the charger's input PG + state. If this pin is not specified a software-based approach for PG + detection is used. +- ti,current-limit: The maximum current to be drawn from the charger's input + (in uA). If this property is not specified, the input limit current is + set automatically using USB D+/D- signal based charger type detection. + If the hardware does not support the D+/D- based detection, a default + of 500,000 is used (=500mA) instead. +- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If + not specified a default of 6,5000,000 (=6.5V) is used. +- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic + power path management (in uV). If not specified a default of 4,360,000 + (=4.36V) is used. Example: bq24257 { compatible = "ti,bq24257"; reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; ti,battery-regulation-voltage = <4200000>; ti,charge-current = <1000000>; ti,termination-current = <50000>; }; + +Example: + +bq24250 { + compatible = "ti,bq24250"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <500000>; + ti,termination-current = <50000>; + ti,current-limit = <900000>; + ti,ovp-voltage = <9500000>; + ti,in-dpm-voltage = <4440000>; +}; diff --git a/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt new file mode 100644 index 000000000000..862f4a49dc49 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt @@ -0,0 +1,34 @@ +AXP20x USB power supply + +Required Properties: +-compatible: "x-powers,axp202-usb-power-supply" + +This node is a subnode of the axp20x PMIC. + +Example: + +axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + x-powers,dcdc-freq = <1500>; + + vdd_cpu: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; + }; + + ... + }; + + usb-power-supply: usb-power-supply { + compatible = "x-powers,axp202-usb-power-supply"; + }; +}; diff --git a/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt new file mode 100644 index 000000000000..65b88fac854b --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt @@ -0,0 +1,131 @@ +Qualcomm Switch-Mode Battery Charger and Boost + +PROPERTIES +- compatible: + Usage: required + Value type: <stringlist> + Description: Must be one of: + - "qcom,pm8941-charger" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Description: Base address of registers for SMBB block + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Description: The format of the specifier is defined by the binding document + describing the node's interrupt parent. Must contain one + specifier for each of the following interrupts, in order: + - charge done + - charge fast mode + - charge trickle mode + - battery temperature ok + - battery present + - charger disconnected + - USB-in valid + - DC-in valid + +- interrupt-names: + Usage: required + Value type: <stringlist> + Description: Must contain the following list, strictly ordered: + "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid" + +- qcom,fast-charge-current-limit: + Usage: optional (default: 1A, or pre-configured value) + Value type: <u32>; uA; range [100mA : 3A] + Description: Maximum charge current; May be clamped to safety limits. + +- qcom,fast-charge-low-threshold-voltage: + Usage: optional (default: 3.2V, or pre-configured value) + Value type: <u32>; uV; range [2.1V : 3.6V] + Description: Battery voltage limit above which fast charging may operate; + Below this value linear or switch-mode auto-trickle-charging + will operate. + +- qcom,fast-charge-high-threshold-voltage: + Usage: optional (default: 4.2V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Battery voltage limit below which fast charging may operate; + The fast charger will attempt to charge the battery to this + voltage. May be clamped to safety limits. + +- qcom,fast-charge-safe-voltage: + Usage: optional (default: 4.2V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Maximum safe battery voltage; May be pre-set by bootloader, in + which case, setting this will harmlessly fail. The property + 'fast-charge-high-watermark' will be clamped by this value. + +- qcom,fast-charge-safe-current: + Usage: optional (default: 1A, or pre-configured value) + Value type: <u32>; uA; range [100mA : 3A] + Description: Maximum safe battery charge current; May pre-set by bootloader, + in which case, setting this will harmlessly fail. The property + 'qcom,fast-charge-current-limit' will be clamped by this value. + +- qcom,auto-recharge-threshold-voltage: + Usage: optional (default: 4.1V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Battery voltage limit below which auto-recharge functionality + will restart charging after end-of-charge; The high cutoff + limit for auto-recharge is 5% above this value. + +- qcom,minimum-input-voltage: + Usage: optional (default: 4.3V, or pre-configured value) + Value type: <u32>; uV; range [4.2V : 9.6V] + Description: Input voltage level above which charging may operate + +- qcom,dc-current-limit: + Usage: optional (default: 100mA, or pre-configured value) + Value type: <u32>; uA; range [100mA : 2.5A] + Description: Default DC charge current limit + +- qcom,disable-dc: + Usage: optional (default: false) + Value type: boolean: <u32> or <empty> + Description: Disable DC charger + +- qcom,jeita-extended-temp-range: + Usage: optional (default: false) + Value type: boolean: <u32> or <empty> + Description: Enable JEITA extended temperature range; This does *not* + adjust the maximum charge voltage or current in the extended + temperature range. It only allows charging when the battery + is in the extended temperature range. Voltage/current + regulation must be done externally to fully comply with + the JEITA safety guidelines if this flag is set. + +EXAMPLE +charger@1000 { + compatible = "qcom,pm8941-charger"; + reg = <0x1000 0x700>; + interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid"; + + qcom,fast-charge-current-limit = <1000000>; + qcom,dc-charge-current-limit = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt new file mode 100644 index 000000000000..98d131acee95 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt @@ -0,0 +1,12 @@ +TPS65217 Charger + +Required Properties: +-compatible: "ti,tps65217-charger" + +This node is a subnode of the tps65217 PMIC. + +Example: + + tps65217-charger { + compatible = "ti,tps65090-charger"; + }; diff --git a/MAINTAINERS b/MAINTAINERS index fe5ed801f062..283d602a0240 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -7505,10 +7505,10 @@ NOKIA N900 POWER SUPPLY DRIVERS M: Pali Rohár <pali.rohar@gmail.com> S: Maintained F: include/linux/power/bq2415x_charger.h -F: include/linux/power/bq27x00_battery.h +F: include/linux/power/bq27xxx_battery.h F: include/linux/power/isp1704_charger.h F: drivers/power/bq2415x_charger.c -F: drivers/power/bq27x00_battery.c +F: drivers/power/bq27xxx_battery.c F: drivers/power/isp1704_charger.c F: drivers/power/rx51_battery.c diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi index 36ae9160b558..482b7aa37808 100644 --- a/arch/arm/boot/dts/twl4030.dtsi +++ b/arch/arm/boot/dts/twl4030.dtsi @@ -22,6 +22,8 @@ charger: bci { compatible = "ti,twl4030-bci"; interrupts = <9>, <2>; + io-channels = <&twl4030_madc 11>; + io-channel-name = "vac"; bci3v1-supply = <&vusb3v1>; }; diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 3f15a5cae167..c5e1943e5427 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -246,7 +246,7 @@ CONFIG_GPIO_TWL4030=y CONFIG_GPIO_PALMAS=y CONFIG_W1=m CONFIG_HDQ_MASTER_OMAP=m -CONFIG_BATTERY_BQ27x00=m +CONFIG_BATTERY_BQ27XXX=m CONFIG_CHARGER_ISP1704=m CONFIG_CHARGER_TWL4030=m CONFIG_CHARGER_BQ2415X=m diff --git a/arch/unicore32/Kconfig b/arch/unicore32/Kconfig index 928237a7b9ca..c9faddc61100 100644 --- a/arch/unicore32/Kconfig +++ b/arch/unicore32/Kconfig @@ -222,7 +222,7 @@ config I2C_BATTERY_BQ27200 tristate "I2C Battery BQ27200 Support" select I2C_PUV3 select POWER_SUPPLY - select BATTERY_BQ27x00 + select BATTERY_BQ27XXX config I2C_EEPROM_AT24 tristate "I2C EEPROMs AT24 support" diff --git a/drivers/power/88pm860x_battery.c b/drivers/power/88pm860x_battery.c index d49579b227ec..63c57dc82ac1 100644 --- a/drivers/power/88pm860x_battery.c +++ b/drivers/power/88pm860x_battery.c @@ -954,47 +954,33 @@ static int pm860x_battery_probe(struct platform_device *pdev) else info->resistor = 300; /* set default internal resistor */ - info->battery = power_supply_register(&pdev->dev, &pm860x_battery_desc, - NULL); + info->battery = devm_power_supply_register(&pdev->dev, + &pm860x_battery_desc, + NULL); if (IS_ERR(info->battery)) return PTR_ERR(info->battery); info->battery->dev.parent = &pdev->dev; - ret = request_threaded_irq(info->irq_cc, NULL, - pm860x_coulomb_handler, IRQF_ONESHOT, - "coulomb", info); + ret = devm_request_threaded_irq(chip->dev, info->irq_cc, NULL, + pm860x_coulomb_handler, IRQF_ONESHOT, + "coulomb", info); if (ret < 0) { dev_err(chip->dev, "Failed to request IRQ: #%d: %d\n", info->irq_cc, ret); - goto out_reg; + return ret; } - ret = request_threaded_irq(info->irq_batt, NULL, pm860x_batt_handler, - IRQF_ONESHOT, "battery", info); + ret = devm_request_threaded_irq(chip->dev, info->irq_batt, NULL, + pm860x_batt_handler, + IRQF_ONESHOT, "battery", info); if (ret < 0) { dev_err(chip->dev, "Failed to request IRQ: #%d: %d\n", info->irq_batt, ret); - goto out_coulomb; + return ret; } return 0; - -out_coulomb: - free_irq(info->irq_cc, info); -out_reg: - power_supply_unregister(info->battery); - return ret; -} - -static int pm860x_battery_remove(struct platform_device *pdev) -{ - struct pm860x_battery_info *info = platform_get_drvdata(pdev); - - free_irq(info->irq_batt, info); - free_irq(info->irq_cc, info); - power_supply_unregister(info->battery); - return 0; } #ifdef CONFIG_PM_SLEEP @@ -1028,7 +1014,6 @@ static struct platform_driver pm860x_battery_driver = { .pm = &pm860x_battery_pm_ops, }, .probe = pm860x_battery_probe, - .remove = pm860x_battery_remove, }; module_platform_driver(pm860x_battery_driver); diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index f8758d6febf8..02b3b313809a 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -157,26 +157,25 @@ config BATTERY_SBS Say Y to include support for SBS battery driver for SBS-compliant gas gauges. -config BATTERY_BQ27x00 - tristate "BQ27x00 battery driver" - depends on I2C || I2C=n +config BATTERY_BQ27XXX + tristate "BQ27xxx battery driver" help - Say Y here to enable support for batteries with BQ27x00 (I2C/HDQ) chips. + Say Y here to enable support for batteries with BQ27xxx (I2C/HDQ) chips. -config BATTERY_BQ27X00_I2C - bool "BQ27200/BQ27500 support" - depends on BATTERY_BQ27x00 +config BATTERY_BQ27XXX_I2C + bool "BQ27xxx I2C support" + depends on BATTERY_BQ27XXX depends on I2C default y help - Say Y here to enable support for batteries with BQ27x00 (I2C) chips. + Say Y here to enable support for batteries with BQ27xxx (I2C) chips. -config BATTERY_BQ27X00_PLATFORM - bool "BQ27000 support" - depends on BATTERY_BQ27x00 +config BATTERY_BQ27XXX_PLATFORM + bool "BQ27xxx HDQ support" + depends on BATTERY_BQ27XXX default y help - Say Y here to enable support for batteries with BQ27000 (HDQ) chips. + Say Y here to enable support for batteries with BQ27xxx (HDQ) chips. config BATTERY_DA9030 tristate "DA9030 battery driver" @@ -313,7 +312,7 @@ config CHARGER_MAX8903 config CHARGER_TWL4030 tristate "OMAP TWL4030 BCI charger driver" - depends on TWL4030_CORE + depends on IIO && TWL4030_CORE help Say Y here to enable support for TWL4030 Battery Charge Interface. @@ -379,6 +378,18 @@ config CHARGER_MAX8998 Say Y to enable support for the battery charger control sysfs and platform data of MAX8998/LP3974 PMICs. +config CHARGER_QCOM_SMBB + tristate "Qualcomm Switch-Mode Battery Charger and Boost" + depends on MFD_SPMI_PMIC || COMPILE_TEST + depends on OF + help + Say Y to include support for the Switch-Mode Battery Charger and + Boost (SMBB) hardware found in Qualcomm PM8941 PMICs. The charger + is an integrated, single-cell lithium-ion battery charger. DT + configuration is required for loading, see the devicetree + documentation for more detail. The base name for this driver is + 'pm8941_charger'. + config CHARGER_BQ2415X tristate "TI BQ2415x battery charger driver" depends on I2C @@ -397,12 +408,13 @@ config CHARGER_BQ24190 Say Y to enable support for the TI BQ24190 battery charger. config CHARGER_BQ24257 - tristate "TI BQ24257 battery charger driver" + tristate "TI BQ24250/24251/24257 battery charger driver" depends on I2C depends on GPIOLIB || COMPILE_TEST depends on REGMAP_I2C help - Say Y to enable support for the TI BQ24257 battery charger. + Say Y to enable support for the TI BQ24250, BQ24251, and BQ24257 battery + chargers. config CHARGER_BQ24735 tristate "TI BQ24735 battery charger support" @@ -434,6 +446,13 @@ config CHARGER_TPS65090 Say Y here to enable support for battery charging with TPS65090 PMIC chips. +config CHARGER_TPS65217 + tristate "TPS65217 battery charger driver" + depends on MFD_TPS65217 + help + Say Y here to enable support for battery charging with TPS65217 + PMIC chips. + config BATTERY_GAUGE_LTC2941 tristate "LTC2941/LTC2943 Battery Gauge Driver" depends on I2C @@ -472,6 +491,13 @@ config CHARGER_RT9455 help Say Y to enable support for Richtek RT9455 battery charger. +config AXP20X_POWER + tristate "AXP20x power supply driver" + depends on MFD_AXP20X + help + This driver provides support for the power supply features of + AXP20x PMIC. + source "drivers/power/reset/Kconfig" endif # POWER_SUPPLY diff --git a/drivers/power/Makefile b/drivers/power/Makefile index 5752ce818f51..b0e1bf190e3d 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_GENERIC_ADC_BATTERY) += generic-adc-battery.o obj-$(CONFIG_PDA_POWER) += pda_power.o obj-$(CONFIG_APM_POWER) += apm_power.o +obj-$(CONFIG_AXP20X_POWER) += axp20x_usb_power.o obj-$(CONFIG_MAX8925_POWER) += max8925_power.o obj-$(CONFIG_WM831X_BACKUP) += wm831x_backup.o obj-$(CONFIG_WM831X_POWER) += wm831x_power.o @@ -29,7 +30,7 @@ obj-$(CONFIG_BATTERY_COLLIE) += collie_battery.o obj-$(CONFIG_BATTERY_IPAQ_MICRO) += ipaq_micro_battery.o obj-$(CONFIG_BATTERY_WM97XX) += wm97xx_battery.o obj-$(CONFIG_BATTERY_SBS) += sbs-battery.o -obj-$(CONFIG_BATTERY_BQ27x00) += bq27x00_battery.o +obj-$(CONFIG_BATTERY_BQ27XXX) += bq27xxx_battery.o obj-$(CONFIG_BATTERY_DA9030) += da9030_battery.o obj-$(CONFIG_BATTERY_DA9052) += da9052-battery.o obj-$(CONFIG_CHARGER_DA9150) += da9150-charger.o @@ -57,6 +58,7 @@ obj-$(CONFIG_CHARGER_MAX14577) += max14577_charger.o obj-$(CONFIG_CHARGER_MAX77693) += max77693_charger.o obj-$(CONFIG_CHARGER_MAX8997) += max8997_charger.o obj-$(CONFIG_CHARGER_MAX8998) += max8998_charger.o +obj-$(CONFIG_CHARGER_QCOM_SMBB) += qcom_smbb.o obj-$(CONFIG_CHARGER_BQ2415X) += bq2415x_charger.o obj-$(CONFIG_CHARGER_BQ24190) += bq24190_charger.o obj-$(CONFIG_CHARGER_BQ24257) += bq24257_charger.o @@ -65,6 +67,7 @@ obj-$(CONFIG_CHARGER_BQ25890) += bq25890_charger.o obj-$(CONFIG_POWER_AVS) += avs/ obj-$(CONFIG_CHARGER_SMB347) += smb347-charger.o obj-$(CONFIG_CHARGER_TPS65090) += tps65090-charger.o +obj-$(CONFIG_CHARGER_TPS65217) += tps65217_charger.o obj-$(CONFIG_POWER_RESET) += reset/ obj-$(CONFIG_AXP288_FUEL_GAUGE) += axp288_fuel_gauge.o obj-$(CONFIG_AXP288_CHARGER) += axp288_charger.o diff --git a/drivers/power/axp20x_usb_power.c b/drivers/power/axp20x_usb_power.c new file mode 100644 index 000000000000..421a90b83567 --- /dev/null +++ b/drivers/power/axp20x_usb_power.c @@ -0,0 +1,248 @@ +/* + * AXP20x PMIC USB power supply status driver + * + * Copyright (C) 2015 Hans de Goede <hdegoede@redhat.com> + * Copyright (C) 2014 Bruno Prémont <bonbons@linux-vserver.org> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/device.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/mfd/axp20x.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/power_supply.h> +#include <linux/regmap.h> +#include <linux/slab.h> + +#define DRVNAME "axp20x-usb-power-supply" + +#define AXP20X_PWR_STATUS_VBUS_PRESENT BIT(5) +#define AXP20X_PWR_STATUS_VBUS_USED BIT(4) + +#define AXP20X_USB_STATUS_VBUS_VALID BIT(2) + +#define AXP20X_VBUS_VHOLD_uV(b) (4000000 + (((b) >> 3) & 7) * 100000) +#define AXP20X_VBUS_CLIMIT_MASK 3 +#define AXP20X_VBUC_CLIMIT_900mA 0 +#define AXP20X_VBUC_CLIMIT_500mA 1 +#define AXP20X_VBUC_CLIMIT_100mA 2 +#define AXP20X_VBUC_CLIMIT_NONE 3 + +#define AXP20X_ADC_EN1_VBUS_CURR BIT(2) +#define AXP20X_ADC_EN1_VBUS_VOLT BIT(3) + +#define AXP20X_VBUS_MON_VBUS_VALID BIT(3) + +struct axp20x_usb_power { + struct regmap *regmap; + struct power_supply *supply; +}; + +static irqreturn_t axp20x_usb_power_irq(int irq, void *devid) +{ + struct axp20x_usb_power *power = devid; + + power_supply_changed(power->supply); + + return IRQ_HANDLED; +} + +static int axp20x_usb_power_get_property(struct power_supply *psy, + enum power_supply_property psp, union power_supply_propval *val) +{ + struct axp20x_usb_power *power = power_supply_get_drvdata(psy); + unsigned int input, v; + int ret; + + switch (psp) { + case POWER_SUPPLY_PROP_VOLTAGE_MIN: + ret = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v); + if (ret) + return ret; + + val->intval = AXP20X_VBUS_VHOLD_uV(v); + return 0; + case POWER_SUPPLY_PROP_VOLTAGE_NOW: + ret = axp20x_read_variable_width(power->regmap, + AXP20X_VBUS_V_ADC_H, 12); + if (ret < 0) + return ret; + + val->intval = ret * 1700; /* 1 step = 1.7 mV */ + return 0; + case POWER_SUPPLY_PROP_CURRENT_MAX: + ret = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v); + if (ret) + return ret; + + switch (v & AXP20X_VBUS_CLIMIT_MASK) { + case AXP20X_VBUC_CLIMIT_100mA: + val->intval = 100000; + break; + case AXP20X_VBUC_CLIMIT_500mA: + val->intval = 500000; + break; + case AXP20X_VBUC_CLIMIT_900mA: + val->intval = 900000; + break; + case AXP20X_VBUC_CLIMIT_NONE: + val->intval = -1; + break; + } + return 0; + case POWER_SUPPLY_PROP_CURRENT_NOW: + ret = axp20x_read_variable_width(power->regmap, + AXP20X_VBUS_I_ADC_H, 12); + if (ret < 0) + return ret; + + val->intval = ret * 375; /* 1 step = 0.375 mA */ + return 0; + default: + break; + } + + /* All the properties below need the input-status reg value */ + ret = regmap_read(power->regmap, AXP20X_PWR_INPUT_STATUS, &input); + if (ret) + return ret; + + switch (psp) { + case POWER_SUPPLY_PROP_HEALTH: + if (!(input & AXP20X_PWR_STATUS_VBUS_PRESENT)) { + val->intval = POWER_SUPPLY_HEALTH_UNKNOWN; + break; + } + + ret = regmap_read(power->regmap, AXP20X_USB_OTG_STATUS, &v); + if (ret) + return ret; + + if (!(v & AXP20X_USB_STATUS_VBUS_VALID)) { + val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE; + break; + } + + val->intval = POWER_SUPPLY_HEALTH_GOOD; |