diff options
41 files changed, 2461 insertions, 101 deletions
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt new file mode 100644 index 000000000000..e2401cd632ab --- /dev/null +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -0,0 +1,19 @@ +i.MX51 Babbage Board +Required root node properties: + - compatible = "fsl,imx51-babbage", "fsl,imx51"; + +i.MX53 Automotive Reference Design Board +Required root node properties: + - compatible = "fsl,imx53-ard", "fsl,imx53"; + +i.MX53 Evaluation Kit +Required root node properties: + - compatible = "fsl,imx53-evk", "fsl,imx53"; + +i.MX53 Quick Start Board +Required root node properties: + - compatible = "fsl,imx53-qsb", "fsl,imx53"; + +i.MX53 Smart Mobile Reference Design Board +Required root node properties: + - compatible = "fsl,imx53-smd", "fsl,imx53"; diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt new file mode 100644 index 000000000000..52916b4aa1fe --- /dev/null +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -0,0 +1,55 @@ +* ARM Generic Interrupt Controller + +ARM SMP cores are often associated with a GIC, providing per processor +interrupts (PPI), shared processor interrupts (SPI) and software +generated interrupts (SGI). + +Primary GIC is attached directly to the CPU and typically has PPIs and SGIs. +Secondary GICs are cascaded into the upward interrupt controller and do not +have PPIs or SGIs. + +Main node required properties: + +- compatible : should be one of: + "arm,cortex-a9-gic" + "arm,arm11mp-gic" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 3. + + The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI + interrupts. + + The 2nd cell contains the interrupt number for the interrupt type. + SPI interrupts are in the range [0-987]. PPI interrupts are in the + range [0-15]. + + The 3rd cell is the flags, encoded as follows: + bits[3:0] trigger type and level flags. + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + bits[15:8] PPI interrupt cpu mask. Each bit corresponds to each of + the 8 possible cpus attached to the GIC. A bit set to '1' indicated + the interrupt is wired to that CPU. Only valid for PPI interrupts. + +- reg : Specifies base physical address(s) and size of the GIC registers. The + first region is the GIC distributor register base and size. The 2nd region is + the GIC cpu interface register base and size. + +Optional +- interrupts : Interrupt source of the parent interrupt controller. Only + present on secondary GICs. + +Example: + + intc: interrupt-controller@fff11000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <1>; + interrupt-controller; + reg = <0xfff11000 0x1000>, + <0xfff10100 0x100>; + }; + diff --git a/Documentation/devicetree/bindings/tty/serial/msm_serial.txt b/Documentation/devicetree/bindings/tty/serial/msm_serial.txt new file mode 100644 index 000000000000..aef383eb8876 --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/msm_serial.txt @@ -0,0 +1,27 @@ +* Qualcomm MSM UART + +Required properties: +- compatible : + - "qcom,msm-uart", and one of "qcom,msm-hsuart" or + "qcom,msm-lsuart". +- reg : offset and length of the register set for the device + for the hsuart operating in compatible mode, there should be a + second pair describing the gsbi registers. +- interrupts : should contain the uart interrupt. + +There are two different UART blocks used in MSM devices, +"qcom,msm-hsuart" and "qcom,msm-lsuart". The msm-serial driver is +able to handle both of these, and matches against the "qcom,msm-uart" +as the compatibility. + +The registers for the "qcom,msm-hsuart" device need to specify both +register blocks, even for the common driver. + +Example: + + uart@19c400000 { + compatible = "qcom,msm-hsuart", "qcom,msm-uart"; + reg = <0x19c40000 0x1000>, + <0x19c00000 0x1000>; + interrupts = <195>; + }; diff --git a/arch/arm/boot/dts/at91sam9g20.dtsi b/arch/arm/boot/dts/at91sam9g20.dtsi new file mode 100644 index 000000000000..aeef04269cf8 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9g20.dtsi @@ -0,0 +1,119 @@ +/* + * at91sam9g20.dtsi - Device Tree Include file for AT91SAM9G20 family SoC + * + * Copyright (C) 2011 Atmel, + * 2011 Nicolas Ferre <nicolas.ferre@atmel.com>, + * 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2 or later. + */ + +/include/ "skeleton.dtsi" + +/ { + model = "Atmel AT91SAM9G20 family SoC"; + compatible = "atmel,at91sam9g20"; + interrupt-parent = <&aic>; + + aliases { + serial0 = &dbgu; + serial1 = &usart0; + serial2 = &usart1; + serial3 = &usart2; + serial4 = &usart3; + serial5 = &usart4; + serial6 = &usart5; + }; + cpus { + cpu@0 { + compatible = "arm,arm926ejs"; + }; + }; + + memory@20000000 { + reg = <0x20000000 0x08000000>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + aic: interrupt-controller@fffff000 { + #interrupt-cells = <1>; + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + interrupt-parent; + reg = <0xfffff000 0x200>; + }; + + dbgu: serial@fffff200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffff200 0x200>; + interrupts = <1>; + status = "disabled"; + }; + + usart0: serial@fffb0000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb0000 0x200>; + interrupts = <6>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart1: serial@fffb4000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb4000 0x200>; + interrupts = <7>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart2: serial@fffb8000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb8000 0x200>; + interrupts = <8>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart3: serial@fffd0000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffd0000 0x200>; + interrupts = <23>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart4: serial@fffd4000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffd4000 0x200>; + interrupts = <24>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart5: serial@fffd8000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffd8000 0x200>; + interrupts = <25>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi new file mode 100644 index 000000000000..db6a45202f26 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -0,0 +1,106 @@ +/* + * at91sam9g45.dtsi - Device Tree Include file for AT91SAM9G45 family SoC + * applies to AT91SAM9G45, AT91SAM9M10, + * AT91SAM9G46, AT91SAM9M11 SoC + * + * Copyright (C) 2011 Atmel, + * 2011 Nicolas Ferre <nicolas.ferre@atmel.com> + * + * Licensed under GPLv2 or later. + */ + +/include/ "skeleton.dtsi" + +/ { + model = "Atmel AT91SAM9G45 family SoC"; + compatible = "atmel,at91sam9g45"; + interrupt-parent = <&aic>; + + aliases { + serial0 = &dbgu; + serial1 = &usart0; + serial2 = &usart1; + serial3 = &usart2; + serial4 = &usart3; + }; + cpus { + cpu@0 { + compatible = "arm,arm926ejs"; + }; + }; + + memory@70000000 { + reg = <0x70000000 0x10000000>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + aic: interrupt-controller@fffff000 { + #interrupt-cells = <1>; + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + interrupt-parent; + reg = <0xfffff000 0x200>; + }; + + dma: dma-controller@ffffec00 { + compatible = "atmel,at91sam9g45-dma"; + reg = <0xffffec00 0x200>; + interrupts = <21>; + }; + + dbgu: serial@ffffee00 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xffffee00 0x200>; + interrupts = <1>; + status = "disabled"; + }; + + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x200>; + interrupts = <7>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart1: serial@fff90000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff90000 0x200>; + interrupts = <8>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart2: serial@fff94000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff94000 0x200>; + interrupts = <9>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart3: serial@fff98000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff98000 0x200>; + interrupts = <10>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts new file mode 100644 index 000000000000..85b34f59cd82 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts @@ -0,0 +1,35 @@ +/* + * at91sam9m10g45ek.dts - Device Tree file for AT91SAM9M10G45-EK board + * + * Copyright (C) 2011 Atmel, + * 2011 Nicolas Ferre <nicolas.ferre@atmel.com> + * + * Licensed under GPLv2 or later. + */ +/dts-v1/; +/include/ "at91sam9g45.dtsi" + +/ { + model = "Atmel AT91SAM9M10G45-EK"; + compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9"; + + chosen { + bootargs = "mem=64M console=ttyS0,115200 mtdparts=atmel_nand:4M(bootstrap/uboot/kernel)ro,60M(rootfs),-(data) root=/dev/mtdblock1 rw rootfstype=jffs2"; + }; + + memory@70000000 { + reg = <0x70000000 0x4000000>; + }; + + ahb { + apb { + dbgu: serial@ffffee00 { + status = "okay"; + }; + + usart1: serial@fff90000 { + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts new file mode 100644 index 000000000000..f8766af11215 --- /dev/null +++ b/arch/arm/boot/dts/imx51-babbage.dts @@ -0,0 +1,135 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "imx51.dtsi" + +/ { + model = "Freescale i.MX51 Babbage Board"; + compatible = "fsl,imx51-babbage", "fsl,imx51"; + + chosen { + bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait"; + }; + + memory { + reg = <0x90000000 0x20000000>; + }; + + soc { + aips@70000000 { /* aips-1 */ + spba@70000000 { + esdhc@70004000 { /* ESDHC1 */ + fsl,cd-internal; + fsl,wp-internal; + status = "okay"; + }; + + esdhc@70008000 { /* ESDHC2 */ + cd-gpios = <&gpio0 6 0>; /* GPIO1_6 */ + wp-gpios = <&gpio0 5 0>; /* GPIO1_5 */ + status = "okay"; + }; + + uart2: uart@7000c000 { /* UART3 */ + fsl,uart-has-rtscts; + status = "okay"; + }; + + ecspi@70010000 { /* ECSPI1 */ + fsl,spi-num-chipselects = <2>; + cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */ + <&gpio3 25 0>; /* GPIO4_25 */ + status = "okay"; + + pmic: mc13892@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mc13892"; + spi-max-frequency = <6000000>; + reg = <0>; + mc13xxx-irq-gpios = <&gpio0 8 0>; /* GPIO1_8 */ + fsl,mc13xxx-uses-regulator; + }; + + flash: at45db321d@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at45db321d", "atmel,at45", "atmel,dataflash"; + spi-max-frequency = <25000000>; + reg = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "Kernel"; + reg = <0x40000 0x3c0000>; + }; + }; + }; + }; + + wdog@73f98000 { /* WDOG1 */ + status = "okay"; + }; + + iomuxc@73fa8000 { + compatible = "fsl,imx51-iomuxc-babbage"; + reg = <0x73fa8000 0x4000>; + }; + + uart0: uart@73fbc000 { + fsl,uart-has-rtscts; + status = "okay"; + }; + + uart1: uart@73fc0000 { + status = "okay"; + }; + }; + + aips@80000000 { /* aips-2 */ + sdma@83fb0000 { + fsl,sdma-ram-script-name = "imx/sdma/sdma-imx51.bin"; + }; + + i2c@83fc4000 { /* I2C2 */ + status = "okay"; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + }; + }; + + fec@83fec000 { + phy-mode = "mii"; + status = "okay"; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power Button"; + gpios = <&gpio1 21 0>; + linux,code = <116>; /* KEY_POWER */ + gpio-key,wakeup; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/imx51.dtsi new file mode 100644 index 000000000000..327ab8e3a4c8 --- /dev/null +++ b/arch/arm/boot/dts/imx51.dtsi @@ -0,0 +1,246 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/include/ "skeleton.dtsi" + +/ { + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + + tzic: tz-interrupt-controller@e0000000 { + compatible = "fsl,imx51-tzic", "fsl,tzic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0xe0000000 0x4000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + ckil { + compatible = "fsl,imx-ckil", "fixed-clock"; + clock-frequency = <32768>; + }; + + ckih1 { + compatible = "fsl,imx-ckih1", "fixed-clock"; + clock-frequency = <22579200>; + }; + + ckih2 { + compatible = "fsl,imx-ckih2", "fixed-clock"; + clock-frequency = <0>; + }; + + osc { + compatible = "fsl,imx-osc", "fixed-clock"; + clock-frequency = <24000000>; + }; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + interrupt-parent = <&tzic>; + ranges; + + aips@70000000 { /* AIPS1 */ + compatible = "fsl,aips-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x70000000 0x10000000>; + ranges; + + spba@70000000 { + compatible = "fsl,spba-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x70000000 0x40000>; + ranges; + + esdhc@70004000 { /* ESDHC1 */ + compatible = "fsl,imx51-esdhc"; + reg = <0x70004000 0x4000>; + interrupts = <1>; + status = "disabled"; + }; + + esdhc@70008000 { /* ESDHC2 */ + compatible = "fsl,imx51-esdhc"; + reg = <0x70008000 0x4000>; + interrupts = <2>; + status = "disabled"; + }; + + uart2: uart@7000c000 { /* UART3 */ + compatible = "fsl,imx51-uart", "fsl,imx21-uart"; + reg = <0x7000c000 0x4000>; + interrupts = <33>; + status = "disabled"; + }; + + ecspi@70010000 { /* ECSPI1 */ + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx51-ecspi"; + reg = <0x70010000 0x4000>; + interrupts = <36>; + status = "disabled"; + }; + + esdhc@70020000 { /* ESDHC3 */ + compatible = "fsl,imx51-esdhc"; + reg = <0x70020000 0x4000>; + interrupts = <3>; + status = "disabled"; + }; + + esdhc@70024000 { /* ESDHC4 */ + compatible = "fsl,imx51-esdhc"; + reg = <0x70024000 0x4000>; + interrupts = <4>; + status = "disabled"; + }; + }; + + gpio0: gpio@73f84000 { /* GPIO1 */ + compatible = "fsl,imx51-gpio", "fsl,imx31-gpio"; + reg = <0x73f84000 0x4000>; + interrupts = <50 51>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio1: gpio@73f88000 { /* GPIO2 */ + compatible = "fsl,imx51-gpio", "fsl,imx31-gpio"; + reg = <0x73f88000 0x4000>; + interrupts = <52 53>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio2: gpio@73f8c000 { /* GPIO3 */ + compatible = "fsl,imx51-gpio", "fsl,imx31-gpio"; + reg = <0x73f8c000 0x4000>; + interrupts = <54 55>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio3: gpio@73f90000 { /* GPIO4 */ + compatible = "fsl,imx51-gpio", "fsl,imx31-gpio"; + reg = <0x73f90000 0x4000>; + interrupts = <56 57>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + wdog@73f98000 { /* WDOG1 */ + compatible = "fsl,imx51-wdt", "fsl,imx21-wdt"; + reg = <0x73f98000 0x4000>; + interrupts = <58>; + status = "disabled"; + }; + + wdog@73f9c000 { /* WDOG2 */ + compatible = "fsl,imx51-wdt", "fsl,imx21-wdt"; + reg = <0x73f9c000 0x4000>; + interrupts = <59>; + status = "disabled"; + }; + + uart0: uart@73fbc000 { + compatible = "fsl,imx51-uart", "fsl,imx21-uart"; + reg = <0x73fbc000 0x4000>; + interrupts = <31>; + status = "disabled"; + }; + + uart1: uart@73fc0000 { + compatible = "fsl,imx51-uart", "fsl,imx21-uart"; + reg = <0x73fc0000 0x4000>; + interrupts = <32>; + status = "disabled"; + }; + }; + + aips@80000000 { /* AIPS2 */ + compatible = "fsl,aips-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x80000000 0x10000000>; + ranges; + + ecspi@83fac000 { /* ECSPI2 */ + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx51-ecspi"; + reg = <0x83fac000 0x4000>; + interrupts = <37>; + status = "disabled"; + }; + + sdma@83fb0000 { + compatible = "fsl,imx51-sdma", "fsl,imx35-sdma"; + reg = <0x83fb0000 0x4000>; + interrupts = <6>; + }; + + cspi@83fc0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx51-cspi", "fsl,imx35-cspi"; + reg = <0x83fc0000 0x4000>; + interrupts = <38>; + status = "disabled"; + }; + + i2c@83fc4000 { /* I2C2 */ + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + reg = <0x83fc4000 0x4000>; + interrupts = <63>; + status = "disabled"; + }; + + i2c@83fc8000 { /* I2C1 */ + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + reg = <0x83fc8000 0x4000>; + interrupts = <62>; + status = "disabled"; + }; + + fec@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + status = "disabled"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx53-ard.dts b/arch/arm/boot/dts/imx53-ard.dts new file mode 100644 index 000000000000..2ab7f80a0a35 --- /dev/null +++ b/arch/arm/boot/dts/imx53-ard.dts @@ -0,0 +1,113 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "imx53.dtsi" + +/ { + model = "Freescale i.MX53 Automotive Reference Design Board"; + compatible = "fsl,imx53-ard", "fsl,imx53"; + + chosen { + bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait"; + }; + + memory { + reg = <0x70000000 0x40000000>; + }; + + soc { + aips@50000000 { /* AIPS1 */ + spba@50000000 { + esdhc@50004000 { /* ESDHC1 */ + cd-gpios = <&gpio0 1 0>; /* GPIO1_1 */ + wp-gpios = <&gpio0 9 0>; /* GPIO1_9 */ + status = "okay"; + }; + }; + + wdog@53f98000 { /* WDOG1 */ + status = "okay"; + }; + + iomuxc@53fa8000 { + compatible = "fsl,imx53-iomuxc-ard"; + reg = <0x53fa8000 0x4000>; + }; + + uart0: uart@53fbc000 { /* UART1 */ + status = "okay"; + }; + }; + + aips@60000000 { /* AIPS2 */ + sdma@63fb0000 { + fsl,sdma-ram-script-name = "imx/sdma/sdma-imx53.bin"; + }; + }; + }; + + eim-cs1@f4000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,eim-bus", "simple-bus"; + reg = <0xf4000000 0x3ff0000>; + ranges; + + lan9220@f4000000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0xf4000000 0x2000000>; + phy-mode = "mii"; + interrupt-parent = <&gpio1>; + interrupts = <31>; + reg-io-width = <4>; + smsc,irq-push-pull; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + home { + label = "Home"; + gpios = <&gpio4 10 0>; /* GPIO5_10 */ + linux,code = <102>; /* KEY_HOME */ + gpio-key,wakeup; + }; + + back { + label = "Back"; + gpios = <&gpio4 11 0>; /* GPIO5_11 */ + linux,code = <158>; /* KEY_BACK */ + gpio-key,wakeup; + }; + + program { + label = "Program"; + gpios = <&gpio4 12 0>; /* GPIO5_12 */ + linux,code = <362>; /* KEY_PROGRAM */ + gpio-key,wakeup; + }; + + volume-up { + label = "Volume Up"; + gpios = <&gpio4 13 0>; /* GPIO5_13 */ + linux,code = <115>; /* KEY_VOLUMEUP */ + }; + + volume-down { + label = "Volume Down"; + gpios = <&gpio3 0 0>; /* GPIO4_0 */ + linux,code = <114>; /* KEY_VOLUMEDOWN */ + }; + }; +}; diff --git a/arch/arm/boot/dts/imx53-evk.dts b/arch/arm/boot/dts/imx53-evk.dts new file mode 100644 index 000000000000..3f3a88185ff8 --- /dev/null +++ b/ |