diff options
55 files changed, 2408 insertions, 649 deletions
diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt index 8854004a1d3a..411375eac54d 100644 --- a/Documentation/devicetree/bindings/spi/fsl-spi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -18,6 +18,10 @@ Optional properties: - gpios : specifies the gpio pins to be used for chipselects. The gpios will be referred to as reg = <index> in the SPI child nodes. If unspecified, a single SPI device without a chip select can be used. +- fsl,spisel_boot : for the MPC8306 and MPC8309, specifies that the + SPISEL_BOOT signal is used as chip select for a slave device. Use + reg = <number of gpios> in the corresponding child node, i.e. 0 if + the gpios property is not present. Example: spi@4c0 { diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt index 9ba7c5a273b4..db8e0d71c5bc 100644 --- a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt @@ -23,6 +23,18 @@ Required properties: Recommended properties: - spi-max-frequency: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt +Optional properties: +- nvidia,tx-clk-tap-delay: Delays the clock going out to the external device + with this tap value. This property is used to tune the outgoing data from + Tegra SPI master with respect to outgoing Tegra SPI master clock. + Tap values vary based on the platform design trace lengths from Tegra SPI + to corresponding slave devices. Valid tap values are from 0 thru 63. +- nvidia,rx-clk-tap-delay: Delays the clock coming in from the external device + with this tap value. This property is used to adjust the Tegra SPI master + clock with respect to the data from the SPI slave device. + Tap values vary based on the platform design trace lengths from Tegra SPI + to corresponding slave devices. Valid tap values are from 0 thru 63. + Example: spi@7000d600 { @@ -38,4 +50,12 @@ spi@7000d600 { reset-names = "spi"; dmas = <&apbdma 16>, <&apbdma 16>; dma-names = "rx", "tx"; + <spi-client>@<bus_num> { + ... + ... + nvidia,rx-clk-tap-delay = <0>; + nvidia,tx-clk-tap-delay = <16>; + ... + }; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index 37cf69586d10..18e14ee257b2 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -4,6 +4,7 @@ Required properties: - compatible : "renesas,msiof-r8a7743" (RZ/G1M) "renesas,msiof-r8a7744" (RZ/G1N) "renesas,msiof-r8a7745" (RZ/G1E) + "renesas,msiof-r8a77470" (RZ/G1C) "renesas,msiof-r8a774a1" (RZ/G2M) "renesas,msiof-r8a774c0" (RZ/G2E) "renesas,msiof-r8a7790" (R-Car H2) diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt index 2864bc6b659c..f54c8c36395e 100644 --- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt @@ -8,9 +8,16 @@ Required properties: - interrupts : One interrupt, used by the controller. - #address-cells : <1>, as required by generic SPI binding. - #size-cells : <0>, also as required by generic SPI binding. +- clocks : phandles for the clocks, see the description of clock-names below. + The phandle for the "ssi_clk" is required. The phandle for the "pclk" clock + is optional. If a single clock is specified but no clock-name, it is the + "ssi_clk" clock. If both clocks are listed, the "ssi_clk" must be first. Optional properties: -- cs-gpios : Specifies the gpio pis to be used for chipselects. +- clock-names : Contains the names of the clocks: + "ssi_clk", for the core clock used to generate the external SPI clock. + "pclk", the interface clock, required for register access. +- cs-gpios : Specifies the gpio pins to be used for chipselects. - num-cs : The number of chipselects. If omitted, this will default to 4. - reg-io-width : The I/O register width (in bytes) implemented by this device. Supported values are 2 or 4 (the default). @@ -25,6 +32,7 @@ Example: interrupts = <0 154 4>; #address-cells = <1>; #size-cells = <0>; + clocks = <&spi_m_clk>; num-cs = <2>; cs-gpios = <&gpio0 13 0>, <&gpio0 14 0>; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt index 6cc3c6fe25a3..e71b81a41ac0 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt @@ -7,7 +7,11 @@ Required properties: - reg : address and length of the lpspi master registers - interrupt-parent : core interrupt controller - interrupts : lpspi interrupt -- clocks : lpspi clock specifier +- clocks : lpspi clock specifier. Its number and order need to correspond to the + value in clock-names. +- clock-names : Corresponding to per clock and ipg clock in "clocks" + respectively. In i.MX7ULP, it only has per clk, so use CLK_DUMMY + to fill the "ipg" blank. - spi-slave : spi slave mode support. In slave mode, add this attribute without value. In master mode, remove it. @@ -18,6 +22,8 @@ lpspi2: lpspi@40290000 { reg = <0x40290000 0x10000>; interrupt-parent = <&intc>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clks IMX7ULP_CLK_LPSPI2>; + clocks = <&clks IMX7ULP_CLK_LPSPI2>, + <&clks IMX7ULP_CLK_DUMMY>; + clock-names = "per", "ipg"; spi-slave; }; diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index 69c356767cf8..c0f6c8ecfa2e 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -10,6 +10,7 @@ Required properties: - mediatek,mt8135-spi: for mt8135 platforms - mediatek,mt8173-spi: for mt8173 platforms - mediatek,mt8183-spi: for mt8183 platforms + - "mediatek,mt8516-spi", "mediatek,mt2712-spi": for mt8516 platforms - #address-cells: should be 1. diff --git a/Documentation/devicetree/bindings/spi/spi-mt7621.txt b/Documentation/devicetree/bindings/spi/spi-mt7621.txt new file mode 100644 index 000000000000..d5baec0fa56e --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-mt7621.txt @@ -0,0 +1,26 @@ +Binding for MTK SPI controller (MT7621 MIPS) + +Required properties: +- compatible: Should be one of the following: + - "ralink,mt7621-spi": for mt7621/mt7628/mt7688 platforms +- #address-cells: should be 1. +- #size-cells: should be 0. +- reg: Address and length of the register set for the device +- resets: phandle to the reset controller asserting this device in + reset + See ../reset/reset.txt for details. + +Optional properties: +- cs-gpios: see spi-bus.txt. + +Example: + +- SoC Specific Portion: +spi0: spi@b00 { + compatible = "ralink,mt7621-spi"; + reg = <0xb00 0x100>; + #address-cells = <1>; + #size-cells = <0>; + resets = <&rstctrl 18>; + reset-names = "spi"; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt b/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt new file mode 100644 index 000000000000..16b734ad3102 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt @@ -0,0 +1,25 @@ +Xilinx Zynq QSPI controller Device Tree Bindings +------------------------------------------------------------------- + +Required properties: +- compatible : Should be "xlnx,zynq-qspi-1.0". +- reg : Physical base address and size of QSPI registers map. +- interrupts : Property with a value describing the interrupt + number. +- clock-names : List of input clock names - "ref_clk", "pclk" + (See clock bindings for details). +- clocks : Clock phandles (see clock bindings for details). + +Optional properties: +- num-cs : Number of chip selects used. + +Example: + qspi: spi@e000d000 { + compatible = "xlnx,zynq-qspi-1.0"; + reg = <0xe000d000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <0 19 4>; + clock-names = "ref_clk", "pclk"; + clocks = <&clkc 10>, <&clkc 43>; + num-cs = <1>; + }; diff --git a/Documentation/spi/spi-summary b/Documentation/spi/spi-summary index 1721c1b570c3..1a63194b74d7 100644 --- a/Documentation/spi/spi-summary +++ b/Documentation/spi/spi-summary @@ -572,6 +572,12 @@ SPI MASTER METHODS 0: transfer is finished 1: transfer is still in progress + master->set_cs_timing(struct spi_device *spi, u8 setup_clk_cycles, + u8 hold_clk_cycles, u8 inactive_clk_cycles) + This method allows SPI client drivers to request SPI master controller + for configuring device specific CS setup, hold and inactive timing + requirements. + DEPRECATED METHODS master->transfer(struct spi_device *spi, struct spi_message *message) diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c index 8e89ec8b6f0f..34e18e9556d9 100644 --- a/arch/arm/mach-ep93xx/edb93xx.c +++ b/arch/arm/mach-ep93xx/edb93xx.c @@ -29,6 +29,7 @@ #include <linux/platform_device.h> #include <linux/i2c.h> #include <linux/spi/spi.h> +#include <linux/gpio/machine.h> #include <sound/cs4271.h> @@ -105,13 +106,16 @@ static struct spi_board_info edb93xx_spi_board_info[] __initdata = { }, }; -static int edb93xx_spi_chipselects[] __initdata = { - EP93XX_GPIO_LINE_EGPIO6, +static struct gpiod_lookup_table edb93xx_spi_cs_gpio_table = { + .dev_id = "ep93xx-spi.0", + .table = { + GPIO_LOOKUP("A", 6, "cs", GPIO_ACTIVE_LOW), + { }, + }, }; static struct ep93xx_spi_info edb93xx_spi_info __initdata = { - .chipselect = edb93xx_spi_chipselects, - .num_chipselect = ARRAY_SIZE(edb93xx_spi_chipselects), + /* Intentionally left blank */ }; static void __init edb93xx_register_spi(void) @@ -123,6 +127,7 @@ static void __init edb93xx_register_spi(void) else if (machine_is_edb9315a()) edb93xx_cs4271_data.gpio_nreset = EP93XX_GPIO_LINE_EGPIO14; + gpiod_add_lookup_table(&edb93xx_spi_cs_gpio_table); ep93xx_register_spi(&edb93xx_spi_info, edb93xx_spi_board_info, ARRAY_SIZE(edb93xx_spi_board_info)); } diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c index 80ccb984d521..f0f38c0dba52 100644 --- a/arch/arm/mach-ep93xx/simone.c +++ b/arch/arm/mach-ep93xx/simone.c @@ -77,13 +77,15 @@ static struct spi_board_info simone_spi_devices[] __initdata = { * low between multi-message command blocks. From v1.4, it uses a GPIO instead. * v1.3 parts will still work, since the signal on SFRMOUT is automatic. */ -static int simone_spi_chipselects[] __initdata = { - EP93XX_GPIO_LINE_EGPIO1, +static struct gpiod_lookup_table simone_spi_cs_gpio_table = { + .dev_id = "ep93xx-spi.0", + .table = { + GPIO_LOOKUP("A", 1, "cs", GPIO_ACTIVE_LOW), + { }, + }, }; static struct ep93xx_spi_info simone_spi_info __initdata = { - .chipselect = simone_spi_chipselects, - .num_chipselect = ARRAY_SIZE(simone_spi_chipselects), .use_dma = 1, }; @@ -113,6 +115,7 @@ static void __init simone_init_machine(void) ep93xx_register_i2c(simone_i2c_board_info, ARRAY_SIZE(simone_i2c_board_info)); gpiod_add_lookup_table(&simone_mmc_spi_gpio_table); + gpiod_add_lookup_table(&simone_spi_cs_gpio_table); ep93xx_register_spi(&simone_spi_info, simone_spi_devices, ARRAY_SIZE(simone_spi_devices)); simone_register_audio(); diff --git a/arch/arm/mach-ep93xx/ts72xx.c b/arch/arm/mach-ep93xx/ts72xx.c index 85b74ac943f0..a3a20c83c6b8 100644 --- a/arch/arm/mach-ep93xx/ts72xx.c +++ b/arch/arm/mach-ep93xx/ts72xx.c @@ -22,6 +22,7 @@ #include <linux/spi/mmc_spi.h> #include <linux/mmc/host.h> #include <linux/platform_data/spi-ep93xx.h> +#include <linux/gpio/machine.h> #include <mach/gpio-ep93xx.h> #include <mach/hardware.h> @@ -269,13 +270,15 @@ static struct spi_board_info bk3_spi_board_info[] __initdata = { * The all work is performed automatically by !SPI_FRAME (SFRM1) and * goes through CPLD */ -static int bk3_spi_chipselects[] __initdata = { - EP93XX_GPIO_LINE_F(3), +static struct gpiod_lookup_table bk3_spi_cs_gpio_table = { + .dev_id = "ep93xx-spi.0", + .table = { + GPIO_LOOKUP("F", 3, "cs", GPIO_ACTIVE_LOW), + { }, + }, }; static struct ep93xx_spi_info bk3_spi_master __initdata = { - .chipselect = bk3_spi_chipselects, - .num_chipselect = ARRAY_SIZE(bk3_spi_chipselects), .use_dma = 1, }; @@ -316,13 +319,17 @@ static struct spi_board_info ts72xx_spi_devices[] __initdata = { }, }; -static int ts72xx_spi_chipselects[] __initdata = { - EP93XX_GPIO_LINE_F(2), /* DIO_17 */ +static struct gpiod_lookup_table ts72xx_spi_cs_gpio_table = { + .dev_id = "ep93xx-spi.0", + .table = { + /* DIO_17 */ + GPIO_LOOKUP("F", 2, "cs", GPIO_ACTIVE_LOW), + { }, + }, }; static struct ep93xx_spi_info ts72xx_spi_info __initdata = { - .chipselect = ts72xx_spi_chipselects, - .num_chipselect = ARRAY_SIZE(ts72xx_spi_chipselects), + /* Intentionally left blank */ }; static void __init ts72xx_init_machine(void) @@ -339,6 +346,7 @@ static void __init ts72xx_init_machine(void) if (board_is_ts7300()) platform_device_register(&ts73xx_fpga_device); #endif + gpiod_add_lookup_table(&ts72xx_spi_cs_gpio_table); ep93xx_register_spi(&ts72xx_spi_info, ts72xx_spi_devices, ARRAY_SIZE(ts72xx_spi_devices)); } @@ -398,6 +406,7 @@ static void __init bk3_init_machine(void) ep93xx_register_eth(&ts72xx_eth_data, 1); + gpiod_add_lookup_table(&bk3_spi_cs_gpio_table); ep93xx_register_spi(&bk3_spi_master, bk3_spi_board_info, ARRAY_SIZE(bk3_spi_board_info)); diff --git a/arch/arm/mach-ep93xx/vision_ep9307.c b/arch/arm/mach-ep93xx/vision_ep9307.c index 767ee64628dc..f95a644769e4 100644 --- a/arch/arm/mach-ep93xx/vision_ep9307.c +++ b/arch/arm/mach-ep93xx/vision_ep9307.c @@ -245,15 +245,17 @@ static struct spi_board_info vision_spi_board_info[] __initdata = { }, }; -static int vision_spi_chipselects[] __initdata = { - EP93XX_GPIO_LINE_EGPIO6, - EP93XX_GPIO_LINE_EGPIO7, - EP93XX_GPIO_LINE_G(2), +static struct gpiod_lookup_table vision_spi_cs_gpio_table = { + .dev_id = "ep93xx-spi.0", + .table = { + GPIO_LOOKUP_IDX("A", 6, "cs", 0, GPIO_ACTIVE_LOW), + GPIO_LOOKUP_IDX("A", 7, "cs", 1, GPIO_ACTIVE_LOW), + GPIO_LOOKUP_IDX("G", 2, "cs", 2, GPIO_ACTIVE_LOW), + { }, + }, }; static struct ep93xx_spi_info vision_spi_master __initdata = { - .chipselect = vision_spi_chipselects, - .num_chipselect = ARRAY_SIZE(vision_spi_chipselects), .use_dma = 1, }; @@ -295,6 +297,7 @@ static void __init vision_init_machine(void) ep93xx_register_i2c(vision_i2c_info, ARRAY_SIZE(vision_i2c_info)); gpiod_add_lookup_table(&vision_spi_mmc_gpio_table); + gpiod_add_lookup_table(&vision_spi_cs_gpio_table); ep93xx_register_spi(&vision_spi_master, vision_spi_board_info, ARRAY_SIZE(vision_spi_board_info)); vision_register_i2s(); diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c index 34e5414c5563..f402aa741bf3 100644 --- a/arch/sh/boards/mach-ecovec24/setup.c +++ b/arch/sh/boards/mach-ecovec24/setup.c @@ -806,7 +806,6 @@ static struct spi_board_info spi_bus[] = { .platform_data = &mmc_spi_info, .max_speed_hz = 5000000, .mode = SPI_MODE_0, - .controller_data = (void *) GPIO_PTM4, }, }; @@ -838,6 +837,14 @@ static struct platform_device msiof0_device = { .resource = msiof0_resources, }; +static struct gpiod_lookup_table msiof_gpio_table = { + .dev_id = "spi_sh_msiof.0", + .table = { + GPIO_LOOKUP("sh7724_pfc", GPIO_PTM4, "cs", GPIO_ACTIVE_HIGH), + { }, + }, +}; + #endif /* FSI */ @@ -1296,12 +1303,11 @@ static int __init arch_setup(void) gpio_request(GPIO_FN_MSIOF0_TXD, NULL); gpio_request(GPIO_FN_MSIOF0_RXD, NULL); gpio_request(GPIO_FN_MSIOF0_TSCK, NULL); - gpio_request(GPIO_PTM4, NULL); /* software CS control of TSYNC pin */ - gpio_direction_output(GPIO_PTM4, 1); /* active low CS */ gpio_request(GPIO_PTB6, NULL); /* 3.3V power control */ gpio_direction_output(GPIO_PTB6, 0); /* disable power by default */ gpiod_add_lookup_table(&mmc_spi_gpio_table); + gpiod_add_lookup_table(&msiof_gpio_table); spi_register_board_info(spi_bus, ARRAY_SIZE(spi_bus)); #endif diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index f761655e2a36..0fba8f400c59 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -426,6 +426,12 @@ config SPI_MT65XX say Y or M here.If you are not sure, say N. SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs. +config SPI_MT7621 + tristate "MediaTek MT7621 SPI Controller" + depends on RALINK || COMPILE_TEST + help + This selects a driver for the MediaTek MT7621 SPI Controller. + config SPI_NPCM_PSPI tristate "Nuvoton NPCM PSPI Controller" depends on ARCH_NPCM || COMPILE_TEST @@ -842,9 +848,17 @@ config SPI_XTENSA_XTFPGA 16 bit words in SPI mode 0, automatically asserting CS on transfer start and deasserting on end. +config SPI_ZYNQ_QSPI + tristate "Xilinx Zynq QSPI controller" + depends on ARCH_ZYNQ || COMPILE_TEST + help + This enables support for the Zynq Quad SPI controller + in master mode. + This controller only supports SPI memory interface. + config SPI_ZYNQMP_GQSPI tristate "Xilinx ZynqMP GQSPI controller" - depends on SPI_MASTER && HAS_DMA + depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST help Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC. diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index d8fc03c9faa2..f2f78d03dc28 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -60,6 +60,7 @@ obj-$(CONFIG_SPI_MPC512x_PSC) += spi-mpc512x-psc.o obj-$(CONFIG_SPI_MPC52xx_PSC) += spi-mpc52xx-psc.o obj-$(CONFIG_SPI_MPC52xx) += spi-mpc52xx.o obj-$(CONFIG_SPI_MT65XX) += spi-mt65xx.o +obj-$(CONFIG_SPI_MT7621) += spi-mt7621.o obj-$(CONFIG_SPI_MXIC) += spi-mxic.o obj-$(CONFIG_SPI_MXS) += spi-mxs.o obj-$(CONFIG_SPI_NPCM_PSPI) += spi-npcm-pspi.o @@ -118,6 +119,7 @@ obj-$(CONFIG_SPI_XCOMM) += spi-xcomm.o obj-$(CONFIG_SPI_XILINX) += spi-xilinx.o obj-$(CONFIG_SPI_XLP) += spi-xlp.o obj-$(CONFIG_SPI_XTENSA_XTFPGA) += spi-xtensa-xtfpga.o +obj-$(CONFIG_SPI_ZYNQ_QSPI) += spi-zynq-qspi.o obj-$(CONFIG_SPI_ZYNQMP_GQSPI) += spi-zynqmp-gqspi.o # SPI slave protocol handlers diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c index b3173ebddade..9f24d5f0b431 100644 --- a/drivers/spi/atmel-quadspi.c +++ b/drivers/spi/atmel-quadspi.c @@ -366,7 +366,7 @@ static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) return err; } -const char *atmel_qspi_get_name(struct spi_mem *spimem) +static const char *atmel_qspi_get_name(struct spi_mem *spimem) { return dev_name(spimem->spi->dev.parent); } diff --git a/drivers/spi/spi-at91-usart.c b/drivers/spi/spi-at91-usart.c index a694d702e574..f763e14bdf12 100644 --- a/drivers/spi/spi-at91-usart.c +++ b/drivers/spi/spi-at91-usart.c @@ -178,12 +178,6 @@ static int at91_usart_spi_setup(struct spi_device *spi) struct at91_usart_spi *aus = spi_master_get_devdata(spi->controller); u32 *ausd = spi->controller_state; unsigned int mr = at91_usart_spi_readl(aus, MR); - u8 bits = spi->bits_per_word; - - if (bits != 8) { - dev_dbg(&spi->dev, "Only 8 bits per word are supported\n"); - return -EINVAL; - } if (spi->mode & SPI_CPOL) mr |= US_MR_CPOL; @@ -212,7 +206,7 @@ static int at91_usart_spi_setup(struct spi_device *spi) dev_dbg(&spi->dev, "setup: bpw %u mode 0x%x -> mr %d %08x\n", - bits, spi->mode, spi->chip_select, mr); + spi->bits_per_word, spi->mode, spi->chip_select, mr); return 0; } diff --git a/drivers/spi/spi-bcm2835.c b/drivers/spi/spi-bcm2835.c index 35aebdfd3b4e..8aa22713c483 100644 --- a/drivers/spi/spi-bcm2835.c +++ b/drivers/spi/spi-bcm2835.c @@ -335,20 +335,6 @@ static int bcm2835_spi_transfer_one_irq(struct spi_master *master, return 1; } -/* - * DMA support - * - * this implementation has currently a few issues in so far as it does - * not work arrount limitations of the HW. - * - * the main one being that DMA transfers are limited to 16 bit - * (so 0 to 65535 bytes) by the SPI HW due to BCM2835_SPI_DLEN - * - * there may be a few more border-cases we may need to address as well - * but unfortunately this would mean splitting up the scatter-gather - * list making it slightly unpractical... - */ - /** * bcm2835_spi_transfer_prologue() - transfer first few bytes without DMA * @master: SPI master @@ -630,19 +616,6 @@ static bool bcm2835_spi_can_dma(struct spi_master *master, if (tfr->len < BCM2835_SPI_DMA_MIN_LENGTH) return false; - /* BCM2835_SPI_DLEN has defined a max transfer size as - * 16 bit, so max is 65535 - * we can revisit this by using an alternative transfer - * method - ideally this would get done without any more - * interaction... - */ - if (tfr->len > 65535) { - dev_warn_once(&spi->dev, - "transfer size of %d too big for dma-transfer\n", - tfr->len); - return false; - } - /* return OK */ return true; } @@ -707,7 +680,6 @@ static void bcm2835_dma_init(struct spi_master *master, struct device *dev) /* all went well, so set can_dma */ master->can_dma = bcm2835_spi_can_dma; - master->max_dma_len = 65535; /* limitation by BCM2835_SPI_DLEN */ /* need to do TX AND RX DMA, so we need dummy buffers */ master->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX; @@ -844,6 +816,17 @@ static int bcm2835_spi_prepare_message(struct spi_master *master, struct spi_device *spi = msg->spi; struct bcm2835_spi *bs = spi_master_get_devdata(master); u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS); + int ret; + + /* + * DMA t |