diff options
119 files changed, 4033 insertions, 1482 deletions
diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index a3089359aaa6..88602b75418e 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -61,7 +61,6 @@ Example: compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0 0x20010000 0 0x1000>; - coresight-default-sink; clocks = <&oscclk6a>; clock-names = "apb_pclk"; port { diff --git a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt new file mode 100644 index 000000000000..af0b903de293 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt @@ -0,0 +1,18 @@ +USB GPIO Extcon device + +This is a virtual device used to generate USB cable states from the USB ID pin +connected to a GPIO pin. + +Required properties: +- compatible: Should be "linux,extcon-usb-gpio" +- id-gpio: gpio for USB ID pin. See gpio binding. + +Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below: + extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>; + } + + &omap_dwc3_1 { + extcon = <&extcon_usb1>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt b/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt new file mode 100644 index 000000000000..f936b5589b19 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt @@ -0,0 +1,75 @@ +* Ingenic JZ4780 NAND/external memory controller (NEMC) + +This file documents the device tree bindings for the NEMC external memory +controller in Ingenic JZ4780 + +Required properties: +- compatible: Should be set to one of: + "ingenic,jz4780-nemc" (JZ4780) +- reg: Should specify the NEMC controller registers location and length. +- clocks: Clock for the NEMC controller. +- #address-cells: Must be set to 2. +- #size-cells: Must be set to 1. +- ranges: A set of ranges for each bank describing the physical memory layout. + Each should specify the following 4 integer values: + + <cs number> 0 <physical address of mapping> <size of mapping> + +Each child of the NEMC node describes a device connected to the NEMC. + +Required child node properties: +- reg: Should contain at least one register specifier, given in the following + format: + + <cs number> <offset> <size> + + Multiple registers can be specified across multiple banks. This is needed, + for example, for packaged NAND devices with multiple dies. Such devices + should be grouped into a single node. + +Optional child node properties: +- ingenic,nemc-bus-width: Specifies the bus width in bits. Defaults to 8 bits. +- ingenic,nemc-tAS: Address setup time in nanoseconds. +- ingenic,nemc-tAH: Address hold time in nanoseconds. +- ingenic,nemc-tBP: Burst pitch time in nanoseconds. +- ingenic,nemc-tAW: Access wait time in nanoseconds. +- ingenic,nemc-tSTRV: Static memory recovery time in nanoseconds. + +If a child node references multiple banks in its "reg" property, the same value +for all optional parameters will be configured for all banks. If any optional +parameters are omitted, they will be left unchanged from whatever they are +configured to when the NEMC device is probed (which may be the reset value as +given in the hardware reference manual, or a value configured by the boot +loader). + +Example (NEMC node with a NAND child device attached at CS1): + +nemc: nemc@13410000 { + compatible = "ingenic,jz4780-nemc"; + reg = <0x13410000 0x10000>; + + #address-cells = <2>; + #size-cells = <1>; + + ranges = <1 0 0x1b000000 0x1000000 + 2 0 0x1a000000 0x1000000 + 3 0 0x19000000 0x1000000 + 4 0 0x18000000 0x1000000 + 5 0 0x17000000 0x1000000 + 6 0 0x16000000 0x1000000>; + + clocks = <&cgu JZ4780_CLK_NEMC>; + + nand: nand@1 { + compatible = "ingenic,jz4780-nand"; + reg = <1 0 0x1000000>; + + ingenic,nemc-tAS = <10>; + ingenic,nemc-tAH = <5>; + ingenic,nemc-tBP = <10>; + ingenic,nemc-tAW = <15>; + ingenic,nemc-tSTRV = <100>; + + ... + }; +}; diff --git a/Documentation/devicetree/bindings/misc/lis302.txt b/Documentation/devicetree/bindings/misc/lis302.txt index 6def86f6b053..2a19bff9693f 100644 --- a/Documentation/devicetree/bindings/misc/lis302.txt +++ b/Documentation/devicetree/bindings/misc/lis302.txt @@ -46,11 +46,18 @@ Optional properties for all bus drivers: interrupt 2 - st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for upper/lower limit + - st,wakeup-threshold: set wakeup threshold + - st,wakeup2-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for + upper/lower limit for second wakeup + engine. + - st,wakeup2-threshold: set wakeup threshold for second wakeup + engine. - st,highpass-cutoff-hz=: 1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of highpass cut-off frequency - st,hipass{1,2}-disable: disable highpass 1/2. - st,default-rate=: set the default rate - - st,axis-{x,y,z}=: set the axis to map to the three coordinates + - st,axis-{x,y,z}=: set the axis to map to the three coordinates. + Negative values can be used for inverted axis. - st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis (used by self-test) diff --git a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt index 715d0998af8e..e16b9b5afc70 100644 --- a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt +++ b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt @@ -1,6 +1,6 @@ Qualcomm SPMI Controller (PMIC Arbiter) -The SPMI PMIC Arbiter is found on the Snapdragon 800 Series. It is an SPMI +The SPMI PMIC Arbiter is found on Snapdragon chipsets. It is an SPMI controller with wrapping arbitration logic to allow for multiple on-chip devices to control a single SPMI master. @@ -19,6 +19,10 @@ Required properties: "core" - core registers "intr" - interrupt controller registers "cnfg" - configuration registers + Registers used only for V2 PMIC Arbiter: + "chnls" - tx-channel per virtual slave registers. + "obsrvr" - rx-channel (called observer) per virtual slave registers. + - reg : address + size pairs describing the PMIC arb register sets; order must |