diff options
123 files changed, 3607 insertions, 3509 deletions
diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 7a95c651ceb3..e807635f9e1c 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -3,10 +3,12 @@ synopsys DWC3 CORE DWC3- USB3 CONTROLLER Required properties: - - compatible: must be "synopsys,dwc3" + - compatible: must be "snps,dwc3" - reg : Address and length of the register set for the device - interrupts: Interrupts used by the dwc3 controller. - - usb-phy : array of phandle for the PHY device + - usb-phy : array of phandle for the PHY device. The first element + in the array is expected to be a handle to the USB2/HS PHY and + the second element is expected to be a handle to the USB3/SS PHY Optional properties: - tx-fifo-resize: determines if the FIFO *has* to be reallocated. @@ -14,7 +16,7 @@ Optional properties: This is usually a subnode to DWC3 glue to which it is connected. dwc3@4a030000 { - compatible = "synopsys,dwc3"; + compatible = "snps,dwc3"; reg = <0x4a030000 0xcfff>; interrupts = <0 92 4> usb-phy = <&usb2_phy>, <&usb3,phy>; diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt new file mode 100644 index 000000000000..477d5bb5e51c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -0,0 +1,24 @@ +Generic USB Properties + +Optional properties: + - maximum-speed: tells USB controllers we want to work up to a certain + speed. Valid arguments are "super-speed", "high-speed", + "full-speed" and "low-speed". In case this isn't passed + via DT, USB controllers should default to their maximum + HW capability. + - dr_mode: tells Dual-Role USB controllers that we want to work on a + particular mode. Valid arguments are "host", + "peripheral" and "otg". In case this attribute isn't + passed via DT, USB DRD controllers should default to + OTG. + +This is an attribute to a USB controller such as: + +dwc3@4a030000 { + compatible = "synopsys,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4> + usb-phy = <&usb2_phy>, <&usb3,phy>; + maximum-speed = "super-speed"; + dr_mode = "otg"; +}; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt index c4c9e9e664aa..ba797d3e6326 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -3,7 +3,7 @@ Tegra SOC USB PHY The device node for Tegra SOC USB PHY: Required properties : - - compatible : Should be "nvidia,tegra20-usb-phy". + - compatible : Should be "nvidia,tegra<chip>-usb-phy". - reg : Defines the following set of registers, in the order listed: - The PHY's own register set. Always present. @@ -24,17 +24,26 @@ Required properties : Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. -Required PHY timing params for utmi phy: +Required PHY timing params for utmi phy, for all chips: - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before start of sync launches RxActive - nvidia,elastic-limit : Variable FIFO Depth of elastic input store - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait before declare IDLE. - nvidia,term-range-adj : Range adjusment on terminations - - nvidia,xcvr-setup : HS driver output control + - Either one of the following for HS driver output control: + - nvidia,xcvr-setup : integer, uses the provided value. + - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read + from the on-chip fuses + If both are provided, nvidia,xcvr-setup-use-fuses takes precedence. - nvidia,xcvr-lsfslew : LS falling slew rate control. - nvidia,xcvr-lsrslew : LS rising slew rate control. +Required PHY timing params for utmi phy, only on Tegra30 and above: + - nvidia,xcvr-hsslew : HS slew rate control. + - nvidia,hssquelch-level : HS squelch detector level. + - nvidia,hsdiscon-level : HS disconnect detector level. + Optional properties: - nvidia,has-legacy-mode : boolean indicates whether this controller can operate in legacy mode (as APX 2500 / 2600). In legacy mode some @@ -48,5 +57,5 @@ Optional properties: peripheral means it is device controller otg means it can operate as either ("on the go") -Required properties for dr_mode == otg: +VBUS control (required for dr_mode == otg, optional for dr_mode == host): - vbus-supply: regulator for VBUS diff --git a/Documentation/devicetree/bindings/usb/samsung-hsotg.txt b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt new file mode 100644 index 000000000000..b83d428a265e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt @@ -0,0 +1,40 @@ +Samsung High Speed USB OTG controller +----------------------------- + +The Samsung HSOTG IP can be found on Samsung SoCs, from S3C6400 onwards. +It gives functionality of OTG-compliant USB 2.0 host and device with +support for USB 2.0 high-speed (480Mbps) and full-speed (12 Mbps) +operation. + +Currently only device mode is supported. + +Binding details +----- + +Required properties: +- compatible: "samsung,s3c6400-hsotg" should be used for all currently + supported SoC, +- interrupt-parent: phandle for the interrupt controller to which the + interrupt signal of the HSOTG block is routed, +- interrupts: specifier of interrupt signal of interrupt controller, + according to bindings of interrupt controller, +- clocks: contains an array of clock specifiers: + - first entry: OTG clock +- clock-names: contains array of clock names: + - first entry: must be "otg" +- vusb_d-supply: phandle to voltage regulator of digital section, +- vusb_a-supply: phandle to voltage regulator of analog section. + +Example +----- + + hsotg@12480000 { + compatible = "samsung,s |