Merge tag 'mac80211-next-for-davem-2016-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Among various cleanups and improvements, we have the following:
 * client FILS authentication support in mac80211 (Jouni)
 * AP/VLAN multicast improvements (Michael Braun)
 * config/advertising support for differing beacon intervals on
   multiple virtual interfaces (Purushottam Kushwaha, myself)
 * deprecate the old WDS mode for cfg80211-based drivers, the
   mode is hardly usable since it doesn't support any "modern"
   features like WPA encryption (2003), HT (2009) or VHT (2014),
   I'm not even sure WEP (introduced in 1997) could be done.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 64 insertions, 5 deletions

diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index 56368e9b4622..259c9c77fdc1 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -600,6 +600,20 @@
  *
  * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
  *
+ * @NL80211_CMD_SET_MULTICAST_TO_UNICAST: Configure if this AP should perform
+ *	multicast to unicast conversion. When enabled, all multicast packets
+ *	with ethertype ARP, IPv4 or IPv6 (possibly within an 802.1Q header)
+ *	will be sent out to each station once with the destination (multicast)
+ *	MAC address replaced by the station's MAC address. Note that this may
+ *	break certain expectations of the receiver, e.g. the ability to drop
+ *	unicast IP packets encapsulated in multicast L2 frames, or the ability
+ *	to not send destination unreachable messages in such cases.
+ *	This can only be toggled per BSS. Configure this on an interface of
+ *	type %NL80211_IFTYPE_AP. It applies to all its VLAN interfaces
+ *	(%NL80211_IFTYPE_AP_VLAN), except for those in 4addr (WDS) mode.
+ *	If %NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED is not present with this
+ *	command, the feature is disabled.
+ *
  * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial
  *	mesh config parameters may be given.
  * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the
@@ -874,6 +888,12 @@
  *	This will contain a %NL80211_ATTR_NAN_MATCH nested attribute and
  *	%NL80211_ATTR_COOKIE.
  *
+ * @NL80211_CMD_UPDATE_CONNECT_PARAMS: Update one or more connect parameters
+ *	for subsequent roaming cases if the driver or firmware uses internal
+ *	BSS selection. This command can be issued only while connected and it
+ *	does not result in a change for the current association. Currently,
+ *	only the %NL80211_ATTR_IE data is used and updated with this command.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -1069,6 +1089,10 @@ enum nl80211_commands {
 	NL80211_CMD_CHANGE_NAN_CONFIG,
 	NL80211_CMD_NAN_MATCH,
 
+	NL80211_CMD_SET_MULTICAST_TO_UNICAST,
+
+	NL80211_CMD_UPDATE_CONNECT_PARAMS,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -1638,8 +1662,16 @@ enum nl80211_commands {
  *	the connection request from a station. nl80211_connect_failed_reason
  *	enum has different reasons of connection failure.
  *
- * @NL80211_ATTR_SAE_DATA: SAE elements in Authentication frames. This starts
- *	with the Authentication transaction sequence number field.
+ * @NL80211_ATTR_AUTH_DATA: Fields and elements in Authentication frames.
+ *	This contains the authentication frame body (non-IE and IE data),
+ *	excluding the Authentication algorithm number, i.e., starting at the
+ *	Authentication transaction sequence number field. It is used with
+ *	authentication algorithms that need special fields to be added into
+ *	the frames (SAE and FILS). Currently, only the SAE cases use the
+ *	initial two fields (Authentication transaction sequence number and
+ *	Status code). However, those fields are included in the attribute data
+ *	for all authentication algorithms to keep the attribute definition
+ *	consistent.
  *
  * @NL80211_ATTR_VHT_CAPABILITY: VHT Capability information element (from
  *	association request when used with NL80211_CMD_NEW_STATION)
@@ -1936,6 +1968,14 @@ enum nl80211_commands {
  *	attribute.
  * @NL80211_ATTR_NAN_MATCH: used to report a match. This is a nested attribute.
  *	See &enum nl80211_nan_match_attributes.
+ * @NL80211_ATTR_FILS_KEK: KEK for FILS (Re)Association Request/Response frame
+ *	protection.
+ * @NL80211_ATTR_FILS_NONCES: Nonces (part of AAD) for FILS (Re)Association
+ *	Request/Response frame protection. This attribute contains the 16 octet
+ *	STA Nonce followed by 16 octets of AP Nonce.
+ *
+ * @NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED: Indicates whether or not multicast
+ *	packets should be send out as unicast to all stations (flag attribute).
  *
  * @NUM_NL80211_ATTR: total number of nl80211_attrs available
  * @NL80211_ATTR_MAX: highest attribute number currently defined
@@ -2195,7 +2235,7 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_CONN_FAILED_REASON,
 
-	NL80211_ATTR_SAE_DATA,
+	NL80211_ATTR_AUTH_DATA,
 
 	NL80211_ATTR_VHT_CAPABILITY,
 
@@ -2336,6 +2376,11 @@ enum nl80211_attrs {
 	NL80211_ATTR_NAN_FUNC,
 	NL80211_ATTR_NAN_MATCH,
 
+	NL80211_ATTR_FILS_KEK,
+	NL80211_ATTR_FILS_NONCES,
+
+	NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -2347,6 +2392,7 @@ enum nl80211_attrs {
 #define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION
 #define	NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG
 #define NL80211_ATTR_IFACE_SOCKET_OWNER NL80211_ATTR_SOCKET_OWNER
+#define NL80211_ATTR_SAE_DATA NL80211_ATTR_AUTH_DATA
 
 /*
  * Allow user space programs to use #ifdef on new attributes by defining them
@@ -3660,6 +3706,9 @@ enum nl80211_bss_status {
  * @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r)
  * @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP)
  * @NL80211_AUTHTYPE_SAE: Simultaneous authentication of equals
+ * @NL80211_AUTHTYPE_FILS_SK: Fast Initial Link Setup shared key
+ * @NL80211_AUTHTYPE_FILS_SK_PFS: Fast Initial Link Setup shared key with PFS
+ * @NL80211_AUTHTYPE_FILS_PK: Fast Initial Link Setup public key
  * @__NL80211_AUTHTYPE_NUM: internal
  * @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm
  * @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by
@@ -3672,6 +3721,9 @@ enum nl80211_auth_type {
 	NL80211_AUTHTYPE_FT,
 	NL80211_AUTHTYPE_NETWORK_EAP,
 	NL80211_AUTHTYPE_SAE,
+	NL80211_AUTHTYPE_FILS_SK,
+	NL80211_AUTHTYPE_FILS_SK_PFS,
+	NL80211_AUTHTYPE_FILS_PK,
 
 	/* keep last */
 	__NL80211_AUTHTYPE_NUM,
@@ -4280,6 +4332,9 @@ enum nl80211_iface_limit_attrs {
  *	of supported channel widths for radar detection.
  * @NL80211_IFACE_COMB_RADAR_DETECT_REGIONS: u32 attribute containing the bitmap
  *	of supported regulatory regions for radar detection.
+ * @NL80211_IFACE_COMB_BI_MIN_GCD: u32 attribute specifying the minimum GCD of
+ *	different beacon intervals supported by all the interface combinations
+ *	in this group (if not present, all beacon intervals be identical).
  * @NUM_NL80211_IFACE_COMB: number of attributes
  * @MAX_NL80211_IFACE_COMB: highest attribute number
  *
@@ -4287,8 +4342,8 @@ enum nl80211_iface_limit_attrs {
  *	limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2
  *	=> allows an AP and a STA that must match BIs
  *
- *	numbers = [ #{AP, P2P-GO} <= 8 ], channels = 1, max = 8
- *	=> allows 8 of AP/GO
+ *	numbers = [ #{AP, P2P-GO} <= 8 ], BI min gcd, channels = 1, max = 8,
+ *	=> allows 8 of AP/GO that can have BI gcd >= min gcd
  *
  *	numbers = [ #{STA} <= 2 ], channels = 2, max = 2
  *	=> allows two STAs on different channels
@@ -4314,6 +4369,7 @@ enum nl80211_if_combination_attrs {
 	NL80211_IFACE_COMB_NUM_CHANNELS,
 	NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS,
 	NL80211_IFACE_COMB_RADAR_DETECT_REGIONS,
+	NL80211_IFACE_COMB_BI_MIN_GCD,
 
 	/* keep last */
 	NUM_NL80211_IFACE_COMB,
@@ -4634,6 +4690,8 @@ enum nl80211_feature_flags {
  *	configuration (AP/mesh) with HT rates.
  * @NL80211_EXT_FEATURE_BEACON_RATE_VHT: Driver supports beacon rate
  *	configuration (AP/mesh) with VHT rates.
+ * @NL80211_EXT_FEATURE_FILS_STA: This driver supports Fast Initial Link Setup
+ *	with user space SME (NL80211_CMD_AUTHENTICATE) in station mode.
  *
  * @NUM_NL80211_EXT_FEATURES: number of extended features.
  * @MAX_NL80211_EXT_FEATURES: highest extended feature index.
@@ -4648,6 +4706,7 @@ enum nl80211_ext_feature_index {
 	NL80211_EXT_FEATURE_BEACON_RATE_LEGACY,
 	NL80211_EXT_FEATURE_BEACON_RATE_HT,
 	NL80211_EXT_FEATURE_BEACON_RATE_VHT,
+	NL80211_EXT_FEATURE_FILS_STA,
 
 	/* add new features before the definition below */
 	NUM_NL80211_EXT_FEATURES,