Merge tag 'tty-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty / serial driver updates from Greg KH:
 "Here is the "large" TTY and Serial driver update for 5.3-rc1.

  It's in the negative number of lines overall as we removed an obsolete
  serial driver that was causing problems for some people who were
  trying to clean up some apis (the mpsc.c driver, which only worked for
  some pre-production hardware that no one has anymore.)

  Other than that, lots of tiny changes, cleaning up small things along
  with some platform-specific serial driver updates.

  All of these have been in linux-next for a while now with no reported
  issues"

* tag 'tty-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (68 commits)
  tty: serial: fsl_lpuart: add imx8qxp support
  serial: imx: set_termios(): preserve RTS state
  serial: imx: set_termios(): clarify RTS/CTS bits calculation
  serial: imx: set_termios(): factor-out 'ucr2' initial value
  serial: sh-sci: Terminate TX DMA during buffer flushing
  serial: sh-sci: Fix TX DMA buffer flushing and workqueue races
  serial: mpsc: Remove obsolete MPSC driver
  serial: 8250: 8250_core: Fix missing unlock on error in serial8250_register_8250_port()
  serial: stm32: add RX and TX FIFO flush
  serial: stm32: add support of RX FIFO threshold
  serial: stm32: add support of TX FIFO threshold
  serial: stm32: update PIO transmission
  serial: stm32: add support of timeout interrupt for RX
  Revert "serial: 8250: Don't service RX FIFO if interrupts are disabled"
  tty/serial/8250: use mctrl_gpio helpers
  serial: mctrl_gpio: Check if GPIO property exisits before requesting it
  serial: 8250: pericom_do_set_divisor can be static
  tty: serial_core: Set port active bit in uart_port_activate
  serial: 8250: Add MSR/MCR TIOCM conversion wrapper functions
  serial: 8250: factor out serial8250_{set,clear}_THRI() helpers
  ...

27 files changed, 864 insertions, 2552 deletions

diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index ebfb0bd5bef5..33ad9d6de532 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -11,6 +11,8 @@
 #include <linux/serial_reg.h>
 #include <linux/dmaengine.h>
 
+#include "../serial_mctrl_gpio.h"
+
 struct uart_8250_dma {
 	int (*tx_dma)(struct uart_8250_port *p);
 	int (*rx_dma)(struct uart_8250_port *p);
@@ -128,6 +130,24 @@ static inline void serial_dl_write(struct uart_8250_port *up, int value)
 	up->dl_write(up, value);
 }
 
+static inline bool serial8250_set_THRI(struct uart_8250_port *up)
+{
+	if (up->ier & UART_IER_THRI)
+		return false;
+	up->ier |= UART_IER_THRI;
+	serial_out(up, UART_IER, up->ier);
+	return true;
+}
+
+static inline bool serial8250_clear_THRI(struct uart_8250_port *up)
+{
+	if (!(up->ier & UART_IER_THRI))
+		return false;
+	up->ier &= ~UART_IER_THRI;
+	serial_out(up, UART_IER, up->ier);
+	return true;
+}
+
 struct uart_8250_port *serial8250_get_port(int line);
 
 void serial8250_rpm_get(struct uart_8250_port *p);
@@ -139,14 +159,82 @@ void serial8250_rpm_put_tx(struct uart_8250_port *p);
 int serial8250_em485_init(struct uart_8250_port *p);
 void serial8250_em485_destroy(struct uart_8250_port *p);
 
+/* MCR <-> TIOCM conversion */
+static inline int serial8250_TIOCM_to_MCR(int tiocm)
+{
+	int mcr = 0;
+
+	if (tiocm & TIOCM_RTS)
+		mcr |= UART_MCR_RTS;
+	if (tiocm & TIOCM_DTR)
+		mcr |= UART_MCR_DTR;
+	if (tiocm & TIOCM_OUT1)
+		mcr |= UART_MCR_OUT1;
+	if (tiocm & TIOCM_OUT2)
+		mcr |= UART_MCR_OUT2;
+	if (tiocm & TIOCM_LOOP)
+		mcr |= UART_MCR_LOOP;
+
+	return mcr;
+}
+
+static inline int serial8250_MCR_to_TIOCM(int mcr)
+{
+	int tiocm = 0;
+
+	if (mcr & UART_MCR_RTS)
+		tiocm |= TIOCM_RTS;
+	if (mcr & UART_MCR_DTR)
+		tiocm |= TIOCM_DTR;
+	if (mcr & UART_MCR_OUT1)
+		tiocm |= TIOCM_OUT1;
+	if (mcr & UART_MCR_OUT2)
+		tiocm |= TIOCM_OUT2;
+	if (mcr & UART_MCR_LOOP)
+		tiocm |= TIOCM_LOOP;
+
+	return tiocm;
+}
+
+/* MSR <-> TIOCM conversion */
+static inline int serial8250_MSR_to_TIOCM(int msr)
+{
+	int tiocm = 0;
+
+	if (msr & UART_MSR_DCD)
+		tiocm |= TIOCM_CAR;
+	if (msr & UART_MSR_RI)
+		tiocm |= TIOCM_RNG;
+	if (msr & UART_MSR_DSR)
+		tiocm |= TIOCM_DSR;
+	if (msr & UART_MSR_CTS)
+		tiocm |= TIOCM_CTS;
+
+	return tiocm;
+}
+
 static inline void serial8250_out_MCR(struct uart_8250_port *up, int value)
 {
 	serial_out(up, UART_MCR, value);
+
+	if (up->gpios)
+		mctrl_gpio_set(up->gpios, serial8250_MCR_to_TIOCM(value));
 }
 
 static inline int serial8250_in_MCR(struct uart_8250_port *up)
 {
-	return serial_in(up, UART_MCR);
+	int mctrl;
+
+	mctrl = serial_in(up, UART_MCR);
+
+	if (up->gpios) {
+		unsigned int mctrl_gpio = 0;
+
+		mctrl_gpio = mctrl_gpio_get_outputs(up->gpios, &mctrl_gpio);
+		mctrl |= serial8250_TIOCM_to_MCR(mctrl_gpio);
+	}
+
+	return mctrl;
 }
 
 #if defined(__alpha__) && !defined(CONFIG_PCI)
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index e441221e04b9..df3bcc0b2d74 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -14,6 +14,7 @@
  *	      serial8250_register_8250_port() ports
  */
 
+#include <linux/acpi.h>
 #include <linux/module.h>
 #include <linux/moduleparam.h>
 #include <linux/ioport.h>
@@ -982,6 +983,8 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
 
 	uart = serial8250_find_match_or_unused(&up->port);
 	if (uart && uart->port.type != PORT_8250_CIR) {
+		struct mctrl_gpios *gpios;
+
 		if (uart->port.dev)
 			uart_remove_one_port(&serial8250_reg, &uart->port);
 
@@ -1016,6 +1019,22 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
 		if (up->port.flags & UPF_FIXED_TYPE)
 			uart->port.type = up->port.type;
 
+		/*
+		 * Only call mctrl_gpio_init(), if the device has no ACPI
+		 * companion device
+		 */
+		if (!has_acpi_companion(uart->port.dev)) {
+			gpios = mctrl_gpio_init(&uart->port, 0);
+			if (IS_ERR(gpios)) {
+				if (PTR_ERR(gpios) != -ENOSYS) {
+					ret = PTR_ERR(gpios);
+					goto out_unlock;
+				}
+			} else {
+				uart->gpios = gpios;
+			}
+		}
+
 		serial8250_set_defaults(uart);
 
 		/* Possibly override default I/O functions.  */
@@ -1082,6 +1101,7 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
 		}
 	}
 
+out_unlock:
 	mutex_unlock(&serial_mutex);
 
 	return ret;
diff --git a/drivers/tty/serial/8250/8250_dma.c b/drivers/tty/serial/8250/8250_dma.c
index bfa1a857f3ff..890fa7ddaa7f 100644
--- a/drivers/tty/serial/8250/8250_dma.c
+++ b/drivers/tty/serial/8250/8250_dma.c
@@ -34,10 +34,8 @@ static void __dma_tx_complete(void *param)
 		uart_write_wakeup(&p->port);
 
 	ret = serial8250_tx_dma(p);
-	if (ret) {
-		p->ier |= UART_IER_THRI;
-		serial_port_out(&p->port, UART_IER, p->ier);
-	}
+	if (ret)
+		serial8250_set_THRI(p);
 
 	spin_unlock_irqrestore(&p->port.lock, flags);
 }
@@ -100,10 +98,7 @@ int serial8250_tx_dma(struct uart_8250_port *p)
 	dma_async_issue_pending(dma->txchan);
 	if (dma->tx_err) {
 		dma->tx_err = 0;
-		if (p->ier & UART_IER_THRI) {
-			p->ier &= ~UART_IER_THRI;
-			serial_out(p, UART_IER, p->ier);
-		}
+		serial8250_clear_THRI(p);
 	}
 	return 0;
 err:
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index 417c7c810df9..b411ba4eb5e9 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -10,6 +10,7 @@
 #include <linux/module.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/serial_8250.h>
@@ -47,7 +48,6 @@
 #define MTK_UART_DMA_EN_RX	0x5
 
 #define MTK_UART_ESCAPE_CHAR	0x77	/* Escape char added under sw fc */
-#define MTK_UART_TX_SIZE	UART_XMIT_SIZE
 #define MTK_UART_RX_SIZE	0x8000
 #define MTK_UART_TX_TRIGGER	1
 #define MTK_UART_RX_TRIGGER	MTK_UART_RX_SIZE
@@ -70,6 +70,7 @@ struct mtk8250_data {
 #ifdef CONFIG_SERIAL_8250_DMA
 	enum dma_rx_status	rx_status;
 #endif
+	int			rx_wakeup_irq;
 };
 
 /* flow control mode */
@@ -89,28 +90,30 @@ static void mtk8250_dma_rx_complete(void *param)
 	struct mtk8250_data *data = up->port.private_data;
 	struct tty_port *tty_port = &up->port.state->port;
 	struct dma_tx_state state;
+	int copied, total, cnt;
 	unsigned char *ptr;
-	int copied;
 
-	dma_sync_single_for_cpu(dma->rxchan->device->dev, dma->rx_addr,
-				dma->rx_size, DMA_FROM_DEVICE);
+	if (data->rx_status == DMA_RX_SHUTDOWN)
+		return;
 
 	dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
+	total = dma->rx_size - state.residue;
+	cnt = total;
 
-	if (data->rx_status == DMA_RX_SHUTDOWN)
-		return;
+	if ((data->rx_pos + cnt) > dma->rx_size)
+		cnt = dma->rx_size - data->rx_pos;
 
-	if ((data->rx_pos + state.residue) <= dma->rx_size) {
-		ptr = (unsigned char *)(data->rx_pos + dma->rx_buf);
-		copied = tty_insert_flip_string(tty_port, ptr, state.residue);
-	} else {
-		ptr = (unsigned char *)(data->rx_pos + dma->rx_buf);
-		copied = tty_insert_flip_string(tty_port, ptr,
-						dma->rx_size - data->rx_pos);
+	ptr = (unsigned char *)(data->rx_pos + dma->rx_buf);
+	copied = tty_insert_flip_string(tty_port, ptr, cnt);
+	data->rx_pos += cnt;
+
+	if (total > cnt) {
 		ptr = (unsigned char *)(dma->rx_buf);
-		copied += tty_insert_flip_string(tty_port, ptr,
-				data->rx_pos + state.residue - dma->rx_size);
+		cnt = total - cnt;
+		copied += tty_insert_flip_string(tty_port, ptr, cnt);
+		data->rx_pos = cnt;
 	}
+
 	up->port.icount.rx += copied;
 
 	tty_flip_buffer_push(tty_port);
@@ -121,9 +124,7 @@ static void mtk8250_dma_rx_complete(void *param)
 static void mtk8250_rx_dma(struct uart_8250_port *up)
 {
 	struct uart_8250_dma *dma = up->dma;
-	struct mtk8250_data *data = up->port.private_data;
 	struct dma_async_tx_descriptor	*desc;
-	struct dma_tx_state	 state;
 
 	desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr,
 					   dma->rx_size, DMA_DEV_TO_MEM,
@@ -138,12 +139,6 @@ static void mtk8250_rx_dma(struct uart_8250_port *up)
 
 	dma->rx_cookie = dmaengine_submit(desc);
 
-	dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
-	data->rx_pos = state.residue;
-
-	dma_sync_single_for_device(dma->rxchan->device->dev, dma->rx_addr,
-				   dma->rx_size, DMA_FROM_DEVICE);
-
 	dma_async_issue_pending(dma->rxchan);
 }
 
@@ -156,13 +151,11 @@ static void mtk8250_dma_enable(struct uart_8250_port *up)
 	if (data->rx_status != DMA_RX_START)
 		return;
 
-	dma->rxconf.direction		= DMA_DEV_TO_MEM;
-	dma->rxconf.src_addr_width	= dma->rx_size / 1024;
-	dma->rxconf.src_addr		= dma->rx_addr;
+	dma->rxconf.src_port_window_size	= dma->rx_size;
+	dma->rxconf.src_addr				= dma->rx_addr;
 
-	dma->txconf.direction		= DMA_MEM_TO_DEV;
-	dma->txconf.dst_addr_width	= MTK_UART_TX_SIZE / 1024;
-	dma->txconf.dst_addr		= dma->tx_addr;
+	dma->txconf.dst_port_window_size	= UART_XMIT_SIZE;
+	dma->txconf.dst_addr				= dma->tx_addr;
 
 	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR |
 		UART_FCR_CLEAR_XMIT);
@@ -551,6 +544,8 @@ static int mtk8250_probe(struct platform_device *pdev)
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 
+	data->rx_wakeup_irq = platform_get_irq(pdev, 1);
+
 	return 0;
 }
 
@@ -572,15 +567,35 @@ static int mtk8250_remove(struct platform_device *pdev)
 static int __maybe_unused mtk8250_suspend(struct device *dev)
 {
 	struct mtk8250_data *data = dev_get_drvdata(dev);
+	int irq = data->rx_wakeup_irq;
+	int err;
 
 	serial8250_suspend_port(data->line);
 
+	pinctrl_pm_select_sleep_state(dev);
+	if (irq >= 0) {
+		err = enable_irq_wake(irq);
+		if (err) {
+			dev_err(dev,
+				"failed to enable irq wake on IRQ %d: %d\n",
+				irq, err);
+			pinctrl_pm_select_default_state(dev);
+			serial8250_resume_port(data->line);
+			return err;
+		}
+	}
+
 	return 0;
 }
 
 static int __maybe_unused mtk8250_resume(struct device *dev)
 {
 	struct mtk8250_data *data = dev_get_drvdata(dev);
+	int irq = data->rx_wakeup_irq;
+
+	if (irq >= 0)
+		disable_irq_wake(irq);
+	pinctrl_pm_select_default_state(dev);
 
 	serial8250_resume_port(data->line);
 
diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c
index 0277479c87e9..0826cfdbd406 100644
--- a/drivers/tty/serial/8250/8250_of.c
+++ b/drivers/tty/serial/8250/8250_of.c
@@ -70,9 +70,10 @@ static int of_platform_serial_setup(struct platform_device *ofdev,
 		/* Get clk rate through clk driver if present */
 		info->clk = devm_clk_get(&ofdev->dev, NULL);
 		if (IS_ERR(info->clk)) {
-			dev_warn(&ofdev->dev,
-				"clk or clock-frequency not defined\n");
 			ret = PTR_ERR(info->clk);
+			if (ret != -EPROBE_DEFER)
+				dev_warn(&ofdev->dev,
+					 "failed to get clock: %d\n", ret);
 			goto err_pmruntime;
 		}
 
@@ -205,18 +206,16 @@ err_pmruntime:
 /*
  * Try to register a serial port
  */
-static const struct of_device_id of_platform_serial_table[];
 static int of_platform_serial_probe(struct platform_device *ofdev)
 {
-	const struct of_device_id *match;
 	struct of_serial_info *info;
 	struct uart_8250_port port8250;
+	unsigned int port_type;
 	u32 tx_threshold;
-	int port_type;
 	int ret;
 
-	match = of_match_device(of_platform_serial_table, &ofdev->dev);
-	if (!match)
+	port_type = (unsigned long)of_device_get_match_data(&ofdev->dev);
+	if (port_type == PORT_UNKNOWN)
 		return -EINVAL;
 
 	if (of_property_read_bool(ofdev->dev.of_node, "used-by-rtas"))
@@ -226,7 +225,6 @@ static int of_platform_serial_probe(struct platform_device *ofdev)
 	if (info == NULL)
 		return -ENOMEM;
 
-	port_type = (unsigned long)match->data;
 	memset(&port8250, 0, sizeof(port8250));
 	ret = of_platform_serial_setup(ofdev, port_type, &port8250.port, info);
 	if (ret)
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index 0a8316632d75..3ef65cbd2478 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -141,18 +141,20 @@ static void omap8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
 
 	serial8250_do_set_mctrl(port, mctrl);
 
-	/*
-	 * Turn off autoRTS if RTS is lowered and restore autoRTS setting
-	 * if RTS is raised
-	 */
-	lcr = serial_in(up, UART_LCR);
-	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
-	if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
-		priv->efr |= UART_EFR_RTS;
-	else
-		priv->efr &= ~UART_EFR_RTS;
-	serial_out(up, UART_EFR, priv->efr);
-	serial_out(up, UART_LCR, lcr);
+	if (!up->gpios) {
+		/*
+		 * Turn off autoRTS if RTS is lowered and restore autoRTS
+		 * setting if RTS is raised
+		 */
+		lcr = serial_in(up, UART_LCR);
+		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+		if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
+			priv->efr |= UART_EFR_RTS;
+		else
+			priv->efr &= ~UART_EFR_RTS;
+		serial_out(up, UART_EFR, priv->efr);
+		serial_out(up, UART_LCR, lcr);
+	}
 }
 
 /*
@@ -453,7 +455,8 @@ static void omap_8250_set_termios(struct uart_port *port,
 	priv->efr = 0;
 	up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF);
 
-	if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) {
+	if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW &&
+	    !up->gpios) {
 		/* Enable AUTOCTS (autoRTS is enabled when RTS is raised) */
 		up->port.status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS;
 		priv->efr |= UART_EFR_CTS;
@@ -923,15 +926,13 @@ static void omap_8250_dma_tx_complete(void *param)
 		ret = omap_8250_tx_dma(p);
 		if (ret)
 			en_thri = true;
-
 	} else if (p->capabilities & UART_CAP_RPM) {
 		en_thri = true;
 	}
 
 	if (en_thri) {
 		dma->tx_err = 1;
-		p->ier |= UART_IER_THRI;
-		serial_port_out(&p->port, UART_IER, p->ier);
+		serial8250_set_THRI(p);
 	}
 
 	spin_unlock_irqrestore(&p->port.lock, flags);
@@ -959,10 +960,7 @@ static int omap_8250_tx_dma(struct uart_8250_port *p)
 			ret = -EBUSY;
 			goto err;
 		}
-		if (p->ier & UART_IER_THRI) {
-			p->ier &= ~UART_IER_THRI;
-			serial_out(p, UART_IER, p->ier);
-		}
+		serial8250_clear_THRI(p);
 		return 0;
 	}
 
@@ -1020,10 +1018,7 @@ static int omap_8250_tx_dma(struct uart_8250_port *p)
 	if (dma->tx_err)
 		dma->tx_err = 0;
 
-	if (p->ier & UART_IER_THRI) {
-		p->ier &= ~UART_IER_THRI;
-		serial_out(p, UART_IER, p->ier);
-	}
+	serial8250_clear_THRI(p);
 	if (skip_byte)
 		serial_out(p, UART_TX, xmit->buf[xmit->tail]);
 	return 0;
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index df41397de478..7f740b37700b 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1326,7 +1326,36 @@ static int pci_default_setup(struct serial_private *priv,
 
 	return setup_port(priv, port, bar, offset, board->reg_shift);
 }
-
+static void
+pericom_do_set_divisor(struct uart_port *port, unsigned int baud,
+			       unsigned int quot, unsigned int quot_frac)
+{
+	int scr;
+	int lcr;
+	int actual_baud;
+	int tolerance;
+
+	for (scr = 5 ; scr <= 15 ; scr++) {
+		actual_baud = 921600 * 16 / scr;
+		tolerance = actual_baud / 50;
+
+		if ((baud < actual_baud + tolerance) &&
+			(baud > actual_baud - tolerance)) {
+
+			lcr = serial_port_in(port, UART_LCR);
+			serial_port_out(port, UART_LCR, lcr | 0x80);
+
+			serial_port_out(port, UART_DLL, 1);
+			serial_port_out(port, UART_DLM, 0);
+			serial_port_out(port, 2, 16 - scr);
+			serial_port_out(port, UART_LCR, lcr);
+			return;
+		} else if (baud > actual_baud) {
+			break;
+		}
+	}
+	serial8250_do_set_divisor(port, baud, quot, quot_frac);
+}
 static int pci_pericom_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
 		  struct uart_8250_port *port, int idx)
@@ -1339,6 +1368,30 @@ static int pci_pericom_setup(struct serial_private *priv,
 	else
 		offset += idx * board->uart_offset;
 
+
+	maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) >>
+		(board->reg_shift + 3);
+
+	if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr)
+		return 1;
+
+	port->port.set_divisor = pericom_do_set_divisor;
+
+	return setup_port(priv, port, bar, offset, board->reg_shift);
+}
+
+static int pci_pericom_setup_four_at_eight(struct serial_private *priv,
+		  const struct pciserial_board *board,
+		  struct uart_8250_port *port, int idx)
+{
+	unsigned int bar, offset = board->first_offset, maxnr;
+
+	bar = FL_GET_BASE(board->flags);
+	if (board->flags & FL_BASE_BARS)
+		bar += idx;
+	else
+		offset += idx * board->uart_offset;
+
 	if (idx==3)
 		offset = 0x38;
 
@@ -1348,6 +1401,8 @@ static int pci_pericom_setup(struct serial_private *priv,
 	if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr)
 		return 1;
 
+	port->port.set_divisor = pericom_do_set_divisor;
+
 	return setup_port(priv, port, bar, offset, board->reg_shift);
 }
 
@@ -1995,7 +2050,7 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.device		= PCI_DEVICE_ID_PERICOM_PI7C9X7954,
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_pericom_setup,
+		.setup		= pci_pericom_setup_four_at_eight,
 	},
 	/*
 	 * PLX
@@ -2032,107 +2087,113 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SDB,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_MPCIE_COM_4S,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4DB,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_MPCIE_COM232_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SMDB,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_MPCIE_COM_4SM,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM422_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM485_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_COM422_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_COM485_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SM,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4SM,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
-		.setup      = pci_pericom_setup,
+		.setup      = pci_pericom_setup_four_at_eight,
 	},
-	/*
+	{
+		.vendor     = PCI_VENDOR_ID_ACCESIO,
+		.device     = PCI_ANY_ID,
+		.subvendor  = PCI_ANY_ID,
+		.subdevice  = PCI_ANY_ID,
+		.setup      = pci_pericom_setup,
+	},	/*
 	 * SBS Technologies, Inc., PMC-OCTALPRO 232
 	 */
 	{
diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c
index 431e69a5a6a0..dfca33141fcc 100644
--- a/drivers/tty/serial/8250/8250_pnp.c
+++ b/drivers/tty/serial/8250/8250_pnp.c
@@ -462,8 +462,8 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
 		return -ENODEV;
 
 	dev_dbg(&dev->dev,
-		 "Setup PNP port: port %lx, mem %pa, irq %d, type %d\n",
-		 uart.port.iobase, &uart.port.mapbase,
+		 "Setup PNP port: port %#lx, mem %#llx, irq %u, type %u\n",
+		 uart.port.iobase, (unsigned long long)uart.port.mapbase,
 		 uart.port.irq, uart.port.iotype);
 
 	if (flags & CIR_PORT) {
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index d2f3310abe54..c1cec808571b 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1502,11 +1502,8 @@ static void __stop_tx_rs485(struct uart_8250_port *p)
 
 static inline void __do_stop_tx(struct uart_8250_port *p)
 {
-	if (p->ier & UART_IER_THRI) {
-		p->ier &= ~UART_IER_THRI;
-		serial_out(p, UART_IER, p->ier);
+	if (serial8250_clear_THRI(p))
 		serial8250_rpm_put_tx(p);
-	}
 }
 
 static inline void __stop_tx(struct uart_8250_port *p)
@@ -1555,10 +1552,7 @@ static inline void __start_tx(struct uart_port *port)
 	if (up->dma && !up->dma->tx_dma(up))
 		return;
 
-	if (!(up->ier & UART_IER_THRI)) {
-		up->ier |= UART_IER_THRI;
-		serial_port_out(port, UART_IER, up->ier);
-
+	if (serial8250_set_THRI(up)) {
 		if (up->bugs & UART_BUG_TXEN) {
 			unsigned char lsr;
 
@@ -1662,6 +1656,8 @@ static void serial8250_disable_ms(struct uart_port *port)
 	if (up->bugs & UART_BUG_NOMSR)
 		return;
 
+	mctrl_gpio_disable_ms(up->gpios);
+
 	up->ier &= ~UART_IER_MSI;
 	serial_port_out(port, UART_IER, up->ier);
 }
@@ -1674,6 +1670,8 @@ static void serial8250_enable_ms(struct uart_port *port)
 	if (up->bugs & UART_BUG_NOMSR)
 		return;
 
+	mctrl_gpio_enable_ms(up->gpios);
+
 	up->ier |= UART_IER_MSI;
 
 	serial8250_rpm_get(up);
@@ -1869,13 +1867,13 @@ int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
 
 	status = serial_port_in(port, UART_LSR);
 
-	if (status & (UART_LSR_DR | UART_LSR_BI) &&
-	    iir & UART_IIR_RDI) {
+	if (status & (UART_LSR_DR | UART_LSR_BI)) {
 		if (!up->dma || handle_rx_dma(up, iir))
 			status = serial8250_rx_chars(up, status);
 	}
 	serial8250_modem_status(up);
-	if ((!up->dma || up->dma->tx_err) && (status & UART_LSR_THRE))
+	if ((!up->dma || up->dma->tx_err) && (status & UART_LSR_THRE) &&
+		(up->ier & UART_IER_THRI))
 		serial8250_tx_chars(up);
 
 	uart_unlock_and_check_sysrq(port, flags);
@@ -1944,22 +1942,17 @@ unsigned int serial8250_do_get_mctrl(struct uart_port *port)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
 	unsigned int status;
-	unsigned int ret;
+	unsigned int val;
 
 	serial8250_rpm_get(up);
 	status = serial8250_modem_status(up);
 	serial8250_rpm_put(up);
 
-	ret = 0;
-	if (status & UART_MSR_DCD)
-		ret |= TIOCM_CAR;
-	if (status & UART_MSR_RI)
-		ret |= TIOCM_RNG;
-	if (status & UART_MSR_DSR)
-		ret |= TIOCM_DSR;
-	if (status & UART_MSR_CTS)
-		ret |= TIOCM_CTS;
-	return ret;
+	val = serial8250_MSR_to_TIOCM(status);
+	if (up->gpios)
+		return mctrl_gpio_get(up->gpios, &val);
+
+	return val;
 }
 EXPORT_SYMBOL_GPL(serial8250_do_get_mctrl);
 
@@ -1973,18 +1966,9 @@ static unsigned int serial8250_get_mctrl(struct uart_port *port)
 void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
-	unsigned char mcr = 0;
+	unsigned char mcr;
 
-	if (mctrl & TIOCM_RTS)
-		mcr |= UART_MCR_RTS;
-	if (mctrl & TIOCM_DTR)
-		mcr |= UART_MCR_DTR;
-	if (mctrl & TIOCM_OUT1)
-		mcr |= UART_MCR_OUT1;
-	if (mctrl & TIOCM_OUT2)
-		mcr |= UART_MCR_OUT2;
-	if (mctrl & TIOCM_LOOP)
-		mcr |= UART_MCR_LOOP;
+	mcr = serial8250_TIOCM_to_MCR(mctrl