Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into sh-latest

80 files changed, 46240 insertions, 1299 deletions

diff --git a/drivers/tty/Kconfig b/drivers/tty/Kconfig
new file mode 100644
index 000000000000..3fd7199301b6
--- /dev/null
+++ b/drivers/tty/Kconfig
@@ -0,0 +1,321 @@
+config VT
+	bool "Virtual terminal" if EXPERT
+	depends on !S390
+	select INPUT
+	default y
+	---help---
+	  If you say Y here, you will get support for terminal devices with
+	  display and keyboard devices. These are called "virtual" because you
+	  can run several virtual terminals (also called virtual consoles) on
+	  one physical terminal. This is rather useful, for example one
+	  virtual terminal can collect system messages and warnings, another
+	  one can be used for a text-mode user session, and a third could run
+	  an X session, all in parallel. Switching between virtual terminals
+	  is done with certain key combinations, usually Alt-<function key>.
+
+	  The setterm command ("man setterm") can be used to change the
+	  properties (such as colors or beeping) of a virtual terminal. The
+	  man page console_codes(4) ("man console_codes") contains the special
+	  character sequences that can be used to change those properties
+	  directly. The fonts used on virtual terminals can be changed with
+	  the setfont ("man setfont") command and the key bindings are defined
+	  with the loadkeys ("man loadkeys") command.
+
+	  You need at least one virtual terminal device in order to make use
+	  of your keyboard and monitor. Therefore, only people configuring an
+	  embedded system would want to say N here in order to save some
+	  memory; the only way to log into such a system is then via a serial
+	  or network connection.
+
+	  If unsure, say Y, or else you won't be able to do much with your new
+	  shiny Linux system :-)
+
+config CONSOLE_TRANSLATIONS
+	depends on VT
+	default y
+	bool "Enable character translations in console" if EXPERT
+	---help---
+	  This enables support for font mapping and Unicode translation
+	  on virtual consoles.
+
+config VT_CONSOLE
+	bool "Support for console on virtual terminal" if EXPERT
+	depends on VT
+	default y
+	---help---
+	  The system console is the device which receives all kernel messages
+	  and warnings and which allows logins in single user mode. If you
+	  answer Y here, a virtual terminal (the device used to interact with
+	  a physical terminal) can be used as system console. This is the most
+	  common mode of operations, so you should say Y here unless you want
+	  the kernel messages be output only to a serial port (in which case
+	  you should say Y to "Console on serial port", below).
+
+	  If you do say Y here, by default the currently visible virtual
+	  terminal (/dev/tty0) will be used as system console. You can change
+	  that with a kernel command line option such as "console=tty3" which
+	  would use the third virtual terminal as system console. (Try "man
+	  bootparam" or see the documentation of your boot loader (lilo or
+	  loadlin) about how to pass options to the kernel at boot time.)
+
+	  If unsure, say Y.
+
+config HW_CONSOLE
+	bool
+	depends on VT && !S390 && !UML
+	default y
+
+config VT_HW_CONSOLE_BINDING
+       bool "Support for binding and unbinding console drivers"
+       depends on HW_CONSOLE
+       default n
+       ---help---
+         The virtual terminal is the device that interacts with the physical
+         terminal through console drivers. On these systems, at least one
+         console driver is loaded. In other configurations, additional console
+         drivers may be enabled, such as the framebuffer console. If more than
+         1 console driver is enabled, setting this to 'y' will allow you to
+         select the console driver that will serve as the backend for the
+         virtual terminals.
+
+	 See <file:Documentation/console/console.txt> for more
+	 information. For framebuffer console users, please refer to
+	 <file:Documentation/fb/fbcon.txt>.
+
+config UNIX98_PTYS
+	bool "Unix98 PTY support" if EXPERT
+	default y
+	---help---
+	  A pseudo terminal (PTY) is a software device consisting of two
+	  halves: a master and a slave. The slave device behaves identical to
+	  a physical terminal; the master device is used by a process to
+	  read data from and write data to the slave, thereby emulating a
+	  terminal. Typical programs for the master side are telnet servers
+	  and xterms.
+
+	  Linux has traditionally used the BSD-like names /dev/ptyxx for
+	  masters and /dev/ttyxx for slaves of pseudo terminals. This scheme
+	  has a number of problems. The GNU C library glibc 2.1 and later,
+	  however, supports the Unix98 naming standard: in order to acquire a
+	  pseudo terminal, a process opens /dev/ptmx; the number of the pseudo
+	  terminal is then made available to the process and the pseudo
+	  terminal slave can be accessed as /dev/pts/<number>. What was
+	  traditionally /dev/ttyp2 will then be /dev/pts/2, for example.
+
+	  All modern Linux systems use the Unix98 ptys.  Say Y unless
+	  you're on an embedded system and want to conserve memory.
+
+config DEVPTS_MULTIPLE_INSTANCES
+	bool "Support multiple instances of devpts"
+	depends on UNIX98_PTYS
+	default n
+	---help---
+	  Enable support for multiple instances of devpts filesystem.
+	  If you want to have isolated PTY namespaces (eg: in containers),
+	  say Y here.  Otherwise, say N. If enabled, each mount of devpts
+	  filesystem with the '-o newinstance' option will create an
+	  independent PTY namespace.
+
+config LEGACY_PTYS
+	bool "Legacy (BSD) PTY support"
+	default y
+	---help---
+	  A pseudo terminal (PTY) is a software device consisting of two
+	  halves: a master and a slave. The slave device behaves identical to
+	  a physical terminal; the master device is used by a process to
+	  read data from and write data to the slave, thereby emulating a
+	  terminal. Typical programs for the master side are telnet servers
+	  and xterms.
+
+	  Linux has traditionally used the BSD-like names /dev/ptyxx
+	  for masters and /dev/ttyxx for slaves of pseudo
+	  terminals. This scheme has a number of problems, including
+	  security.  This option enables these legacy devices; on most
+	  systems, it is safe to say N.
+
+
+config LEGACY_PTY_COUNT
+	int "Maximum number of legacy PTY in use"
+	depends on LEGACY_PTYS
+	range 0 256
+	default "256"
+	---help---
+	  The maximum number of legacy PTYs that can be used at any one time.
+	  The default is 256, and should be more than enough.  Embedded
+	  systems may want to reduce this to save memory.
+
+	  When not in use, each legacy PTY occupies 12 bytes on 32-bit
+	  architectures and 24 bytes on 64-bit architectures.
+
+config BFIN_JTAG_COMM
+	tristate "Blackfin JTAG Communication"
+	depends on BLACKFIN
+	help
+	  Add support for emulating a TTY device over the Blackfin JTAG.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called bfin_jtag_comm.
+
+config BFIN_JTAG_COMM_CONSOLE
+	bool "Console on Blackfin JTAG"
+	depends on BFIN_JTAG_COMM=y
+
+config SERIAL_NONSTANDARD
+	bool "Non-standard serial port support"
+	depends on HAS_IOMEM
+	---help---
+	  Say Y here if you have any non-standard serial boards -- boards
+	  which aren't supported using the standard "dumb" serial driver.
+	  This includes intelligent serial boards such as Cyclades,
+	  Digiboards, etc. These are usually used for systems that need many
+	  serial ports because they serve many terminals or dial-in
+	  connections.
+
+	  Note that the answer to this question won't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about non-standard serial boards.
+
+	  Most people can say N here.
+
+config ROCKETPORT
+	tristate "Comtrol RocketPort support"
+	depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
+	help
+	  This driver supports Comtrol RocketPort and RocketModem PCI boards.   
+          These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or
+          modems.  For information about the RocketPort/RocketModem  boards
+          and this driver read <file:Documentation/serial/rocket.txt>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called rocket.
+
+	  If you want to compile this driver into the kernel, say Y here.  If
+          you don't have a Comtrol RocketPort/RocketModem card installed, say N.
+
+config CYCLADES
+	tristate "Cyclades async mux support"
+	depends on SERIAL_NONSTANDARD && (PCI || ISA)
+	select FW_LOADER
+	---help---
+	  This driver supports Cyclades Z and Y multiserial boards.
+	  You would need something like this to connect more than two modems to
+	  your Linux box, for instance in order to become a dial-in server.
+
+	  For information about the Cyclades-Z card, read
+	  <file:Documentation/serial/README.cycladesZ>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called cyclades.
+
+	  If you haven't heard about it, it's safe to say N.
+
+config CYZ_INTR
+	bool "Cyclades-Z interrupt mode operation (EXPERIMENTAL)"
+	depends on EXPERIMENTAL && CYCLADES
+	help
+	  The Cyclades-Z family of multiport cards allows 2 (two) driver op
+	  modes: polling and interrupt. In polling mode, the driver will check
+	  the status of the Cyclades-Z ports every certain amount of time
+	  (which is called polling cycle and is configurable). In interrupt
+	  mode, it will use an interrupt line (IRQ) in order to check the
+	  status of the Cyclades-Z ports. The default op mode is polling. If
+	  unsure, say N.
+
+config MOXA_INTELLIO
+	tristate "Moxa Intellio support"
+	depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
+	select FW_LOADER
+	help
+	  Say Y here if you have a Moxa Intellio multiport serial card.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called moxa.
+
+config MOXA_SMARTIO
+	tristate "Moxa SmartIO support v. 2.0"
+	depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA)
+	help
+	  Say Y here if you have a Moxa SmartIO multiport serial card and/or
+	  want to help develop a new version of this driver.
+
+	  This is upgraded (1.9.1) driver from original Moxa drivers with
+	  changes finally resulting in PCI probing.
+
+	  This driver can also be built as a module. The module will be called
+	  mxser. If you want to do that, say M here.
+
+config SYNCLINK
+	tristate "Microgate SyncLink card support"
+	depends on SERIAL_NONSTANDARD && PCI && ISA_DMA_API
+	help
+	  Provides support for the SyncLink ISA and PCI multiprotocol serial
+	  adapters. These adapters support asynchronous and HDLC bit
+	  synchronous communication up to 10Mbps (PCI adapter).
+
+	  This driver can only be built as a module ( = code which can be
+	  inserted in and removed from the running kernel whenever you want).
+	  The module will be called synclink.  If you want to do that, say M
+	  here.
+
+config SYNCLINKMP
+	tristate "SyncLink Multiport support"
+	depends on SERIAL_NONSTANDARD && PCI
+	help
+	  Enable support for the SyncLink Multiport (2 or 4 ports)
+	  serial adapter, running asynchronous and HDLC communications up
+	  to 2.048Mbps. Each ports is independently selectable for
+	  RS-232, V.35, RS-449, RS-530, and X.21
+
+	  This driver may be built as a module ( = code which can be
+	  inserted in and removed from the running kernel whenever you want).
+	  The module will be called synclinkmp.  If you want to do that, say M
+	  here.
+
+config SYNCLINK_GT
+	tristate "SyncLink GT/AC support"
+	depends on SERIAL_NONSTANDARD && PCI
+	help
+	  Support for SyncLink GT and SyncLink AC families of
+	  synchronous and asynchronous serial adapters
+	  manufactured by Microgate Systems, Ltd. (www.microgate.com)
+
+config NOZOMI
+	tristate "HSDPA Broadband Wireless Data Card - Globe Trotter"
+	depends on PCI && EXPERIMENTAL
+	help
+	  If you have a HSDPA driver Broadband Wireless Data Card -
+	  Globe Trotter PCMCIA card, say Y here.
+
+	  To compile this driver as a module, choose M here, the module
+	  will be called nozomi.
+
+config ISI
+	tristate "Multi-Tech multiport card support (EXPERIMENTAL)"
+	depends on SERIAL_NONSTANDARD && PCI
+	select FW_LOADER
+	help
+	  This is a driver for the Multi-Tech cards which provide several
+	  serial ports.  The driver is experimental and can currently only be
+	  built as a module. The module will be called isicom.
+	  If you want to do that, choose M here.
+
+config N_HDLC
+	tristate "HDLC line discipline support"
+	depends on SERIAL_NONSTANDARD
+	help
+	  Allows synchronous HDLC communications with tty device drivers that
+	  support synchronous HDLC such as the Microgate SyncLink adapter.
+
+	  This driver can be built as a module ( = code which can be
+	  inserted in and removed from the running kernel whenever you want).
+	  The module will be called n_hdlc. If you want to do that, say M
+	  here.
+
+config N_GSM
+	tristate "GSM MUX line discipline support (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	depends on NET
+	help
+	  This line discipline provides support for the GSM MUX protocol and
+	  presents the mux as a set of 61 individual tty devices.
+
diff --git a/drivers/tty/Makefile b/drivers/tty/Makefile
index 396277216e4f..690522fcb338 100644
--- a/drivers/tty/Makefile
+++ b/drivers/tty/Makefile
@@ -11,3 +11,18 @@ obj-$(CONFIG_R3964)		+= n_r3964.o
 obj-y				+= vt/
 obj-$(CONFIG_HVC_DRIVER)	+= hvc/
 obj-y				+= serial/
+
+# tty drivers
+obj-$(CONFIG_AMIGA_BUILTIN_SERIAL) += amiserial.o
+obj-$(CONFIG_BFIN_JTAG_COMM)	+= bfin_jtag_comm.o
+obj-$(CONFIG_CYCLADES)		+= cyclades.o
+obj-$(CONFIG_ISI)		+= isicom.o
+obj-$(CONFIG_MOXA_INTELLIO)	+= moxa.o
+obj-$(CONFIG_MOXA_SMARTIO)	+= mxser.o
+obj-$(CONFIG_NOZOMI)		+= nozomi.o
+obj-$(CONFIG_ROCKETPORT)	+= rocket.o
+obj-$(CONFIG_SYNCLINK_GT)	+= synclink_gt.o
+obj-$(CONFIG_SYNCLINKMP)	+= synclinkmp.o
+obj-$(CONFIG_SYNCLINK)		+= synclink.o
+
+obj-y += ipwireless/
diff --git a/drivers/tty/amiserial.c b/drivers/tty/amiserial.c
new file mode 100644
index 000000000000..f214e5022472
--- /dev/null
+++ b/drivers/tty/amiserial.c
@@ -0,0 +1,2178 @@
+/*
+ *  linux/drivers/char/amiserial.c
+ *
+ * Serial driver for the amiga builtin port.
+ *
+ * This code was created by taking serial.c version 4.30 from kernel
+ * release 2.3.22, replacing all hardware related stuff with the
+ * corresponding amiga hardware actions, and removing all irrelevant
+ * code. As a consequence, it uses many of the constants and names
+ * associated with the registers and bits of 16550 compatible UARTS -
+ * but only to keep track of status, etc in the state variables. It
+ * was done this was to make it easier to keep the code in line with
+ * (non hardware specific) changes to serial.c.
+ *
+ * The port is registered with the tty driver as minor device 64, and
+ * therefore other ports should should only use 65 upwards.
+ *
+ * Richard Lucock 28/12/99
+ *
+ *  Copyright (C) 1991, 1992  Linus Torvalds
+ *  Copyright (C) 1992, 1993, 1994, 1995, 1996, 1997, 
+ * 		1998, 1999  Theodore Ts'o
+ *
+ */
+
+/*
+ * Serial driver configuration section.  Here are the various options:
+ *
+ * SERIAL_PARANOIA_CHECK
+ * 		Check the magic number for the async_structure where
+ * 		ever possible.
+ */
+
+#include <linux/delay.h>
+
+#undef SERIAL_PARANOIA_CHECK
+#define SERIAL_DO_RESTART
+
+/* Set of debugging defines */
+
+#undef SERIAL_DEBUG_INTR
+#undef SERIAL_DEBUG_OPEN
+#undef SERIAL_DEBUG_FLOW
+#undef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
+
+/* Sanity checks */
+
+#if defined(MODULE) && defined(SERIAL_DEBUG_MCOUNT)
+#define DBG_CNT(s) printk("(%s): [%x] refc=%d, serc=%d, ttyc=%d -> %s\n", \
+ tty->name, (info->flags), serial_driver->refcount,info->count,tty->count,s)
+#else
+#define DBG_CNT(s)
+#endif
+
+/*
+ * End of serial driver configuration section.
+ */
+
+#include <linux/module.h>
+
+#include <linux/types.h>
+#include <linux/serial.h>
+#include <linux/serialP.h>
+#include <linux/serial_reg.h>
+static char *serial_version = "4.30";
+
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/timer.h>
+#include <linux/interrupt.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/console.h>
+#include <linux/major.h>
+#include <linux/string.h>
+#include <linux/fcntl.h>
+#includ