Merge tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial driver updates from Greg KH:
 "Here is the big tty/serial driver patchset for 4.11-rc1.

  Not much here, but a lot of little fixes and individual serial driver
  updates all over the subsystem. Majority are for the sh-sci driver and
  platform (the arch-specific changes have acks from the maintainer).

  The start of the "serial bus" code is here as well, but nothing is
  converted to use it yet. That work is still ongoing, hopefully will
  start to show up across different subsystems for 4.12 (bluetooth is
  one major place that will be used.)

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (109 commits)
  tty: pl011: Work around QDF2400 E44 stuck BUSY bit
  atmel_serial: Use the fractional divider when possible
  tty: Remove extra include in HVC console tty framework
  serial: exar: Enable MSI support
  serial: exar: Move register defines from uapi header to consumer site
  serial: pci: Remove unused pci_boards entries
  serial: exar: Move Commtech adapters to 8250_exar as well
  serial: exar: Fix feature control register constants
  serial: exar: Fix initialization of EXAR registers for ports > 0
  serial: exar: Fix mapping of port I/O resources
  serial: sh-sci: fix hardware RX trigger level setting
  tty/serial: atmel: ensure state is restored after suspending
  serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt
  serdev: ttyport: check whether tty_init_dev() fails
  serial: 8250_pci: make pciserial_detach_ports() static
  ARM: dts: STiH410-b2260: Enable HW flow-control
  ARM: dts: STiH407-family: Use new Pinctrl groups
  ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control
  ARM: dts: STiH410-b2260: Identify the UART RTS line
  dt-bindings: serial: Update 'uart-has-rtscts' description
  ...

56 files changed, 1637 insertions, 1226 deletions

diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index c89fafc972b6..6ee55a2d47bb 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -201,8 +201,31 @@ static unsigned int dw8250_serial_in32be(struct uart_port *p, int offset)
 
 static int dw8250_handle_irq(struct uart_port *p)
 {
+	struct uart_8250_port *up = up_to_u8250p(p);
 	struct dw8250_data *d = p->private_data;
 	unsigned int iir = p->serial_in(p, UART_IIR);
+	unsigned int status;
+	unsigned long flags;
+
+	/*
+	 * There are ways to get Designware-based UARTs into a state where
+	 * they are asserting UART_IIR_RX_TIMEOUT but there is no actual
+	 * data available.  If we see such a case then we'll do a bogus
+	 * read.  If we don't do this then the "RX TIMEOUT" interrupt will
+	 * fire forever.
+	 *
+	 * This problem has only been observed so far when not in DMA mode
+	 * so we limit the workaround only to non-DMA mode.
+	 */
+	if (!up->dma && ((iir & 0x3f) == UART_IIR_RX_TIMEOUT)) {
+		spin_lock_irqsave(&p->lock, flags);
+		status = p->serial_in(p, UART_LSR);
+
+		if (!(status & (UART_LSR_DR | UART_LSR_BI)))
+			(void) p->serial_in(p, UART_RX);
+
+		spin_unlock_irqrestore(&p->lock, flags);
+	}
 
 	if (serial8250_handle_irq(p, iir))
 		return 1;
@@ -248,11 +271,11 @@ static void dw8250_set_termios(struct uart_port *p, struct ktermios *termios,
 	if (!ret)
 		p->uartclk = rate;
 
+out:
 	p->status &= ~UPSTAT_AUTOCTS;
 	if (termios->c_cflag & CRTSCTS)
 		p->status |= UPSTAT_AUTOCTS;
 
-out:
 	serial8250_do_set_termios(p, termios, old);
 }
 
@@ -326,13 +349,11 @@ static void dw8250_quirks(struct uart_port *p, struct dw8250_data *data)
 			p->serial_in = dw8250_serial_in32;
 			data->uart_16550_compatible = true;
 		}
-		p->set_termios = dw8250_set_termios;
 	}
 
 	/* Platforms with iDMA */
 	if (platform_get_resource_byname(to_platform_device(p->dev),
 					 IORESOURCE_MEM, "lpss_priv")) {
-		p->set_termios = dw8250_set_termios;
 		data->dma.rx_param = p->dev->parent;
 		data->dma.tx_param = p->dev->parent;
 		data->dma.fn = dw8250_idma_filter;
@@ -414,6 +435,7 @@ static int dw8250_probe(struct platform_device *pdev)
 	p->serial_in	= dw8250_serial_in;
 	p->serial_out	= dw8250_serial_out;
 	p->set_ldisc	= dw8250_set_ldisc;
+	p->set_termios	= dw8250_set_termios;
 
 	p->membase = devm_ioremap(dev, regs->start, resource_size(regs));
 	if (!p->membase)
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
new file mode 100644
index 000000000000..b89c4ffc0486
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -0,0 +1,487 @@
+/*
+ *  Probe module for 8250/16550-type Exar chips PCI serial ports.
+ *
+ *  Based on drivers/tty/serial/8250/8250_pci.c,
+ *
+ *  Copyright (C) 2017 Sudip Mukherjee, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/serial_core.h>
+#include <linux/serial_reg.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/tty.h>
+#include <linux/8250_pci.h>
+
+#include <asm/byteorder.h>
+
+#include "8250.h"
+
+#define PCI_DEVICE_ID_COMMTECH_4224PCI335	0x0002
+#define PCI_DEVICE_ID_COMMTECH_4222PCI335	0x0004
+#define PCI_DEVICE_ID_COMMTECH_2324PCI335	0x000a
+#define PCI_DEVICE_ID_COMMTECH_2328PCI335	0x000b
+#define PCI_DEVICE_ID_COMMTECH_4224PCIE		0x0020
+#define PCI_DEVICE_ID_COMMTECH_4228PCIE		0x0021
+#define PCI_DEVICE_ID_COMMTECH_4222PCIE		0x0022
+#define PCI_DEVICE_ID_EXAR_XR17V4358		0x4358
+#define PCI_DEVICE_ID_EXAR_XR17V8358		0x8358
+
+#define UART_EXAR_8XMODE	0x88	/* 8X sampling rate select */
+
+#define UART_EXAR_FCTR		0x08	/* Feature Control Register */
+#define UART_FCTR_EXAR_IRDA	0x10	/* IrDa data encode select */
+#define UART_FCTR_EXAR_485	0x20	/* Auto 485 half duplex dir ctl */
+#define UART_FCTR_EXAR_TRGA	0x00	/* FIFO trigger table A */
+#define UART_FCTR_EXAR_TRGB	0x60	/* FIFO trigger table B */
+#define UART_FCTR_EXAR_TRGC	0x80	/* FIFO trigger table C */
+#define UART_FCTR_EXAR_TRGD	0xc0	/* FIFO trigger table D programmable */
+
+#define UART_EXAR_TXTRG		0x0a	/* Tx FIFO trigger level write-only */
+#define UART_EXAR_RXTRG		0x0b	/* Rx FIFO trigger level write-only */
+
+#define UART_EXAR_MPIOINT_7_0	0x8f	/* MPIOINT[7:0] */
+#define UART_EXAR_MPIOLVL_7_0	0x90	/* MPIOLVL[7:0] */
+#define UART_EXAR_MPIO3T_7_0	0x91	/* MPIO3T[7:0] */
+#define UART_EXAR_MPIOINV_7_0	0x92	/* MPIOINV[7:0] */
+#define UART_EXAR_MPIOSEL_7_0	0x93	/* MPIOSEL[7:0] */
+#define UART_EXAR_MPIOOD_7_0	0x94	/* MPIOOD[7:0] */
+#define UART_EXAR_MPIOINT_15_8	0x95	/* MPIOINT[15:8] */
+#define UART_EXAR_MPIOLVL_15_8	0x96	/* MPIOLVL[15:8] */
+#define UART_EXAR_MPIO3T_15_8	0x97	/* MPIO3T[15:8] */
+#define UART_EXAR_MPIOINV_15_8	0x98	/* MPIOINV[15:8] */
+#define UART_EXAR_MPIOSEL_15_8	0x99	/* MPIOSEL[15:8] */
+#define UART_EXAR_MPIOOD_15_8	0x9a	/* MPIOOD[15:8] */
+
+struct exar8250;
+
+/**
+ * struct exar8250_board - board information
+ * @num_ports: number of serial ports
+ * @reg_shift: describes UART register mapping in PCI memory
+ */
+struct exar8250_board {
+	unsigned int num_ports;
+	unsigned int reg_shift;
+	bool has_slave;
+	int	(*setup)(struct exar8250 *, struct pci_dev *,
+			 struct uart_8250_port *, int);
+	void	(*exit)(struct pci_dev *pcidev);
+};
+
+struct exar8250 {
+	unsigned int		nr;
+	struct exar8250_board	*board;
+	int			line[0];
+};
+
+static int default_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+			 int idx, unsigned int offset,
+			 struct uart_8250_port *port)
+{
+	const struct exar8250_board *board = priv->board;
+	unsigned int bar = 0;
+
+	if (!pcim_iomap_table(pcidev)[bar] && !pcim_iomap(pcidev, bar, 0))
+		return -ENOMEM;
+
+	port->port.iotype = UPIO_MEM;
+	port->port.mapbase = pci_resource_start(pcidev, bar) + offset;
+	port->port.membase = pcim_iomap_table(pcidev)[bar] + offset;
+	port->port.regshift = board->reg_shift;
+
+	return 0;
+}
+
+static int
+pci_fastcom335_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+		     struct uart_8250_port *port, int idx)
+{
+	unsigned int offset = idx * 0x200;
+	unsigned int baud = 1843200;
+	u8 __iomem *p;
+	int err;
+
+	port->port.flags |= UPF_EXAR_EFR;
+	port->port.uartclk = baud * 16;
+
+	err = default_setup(priv, pcidev, idx, offset, port);
+	if (err)
+		return err;
+
+	p = port->port.membase;
+
+	writeb(0x00, p + UART_EXAR_8XMODE);
+	writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR);
+	writeb(32, p + UART_EXAR_TXTRG);
+	writeb(32, p + UART_EXAR_RXTRG);
+
+	/*
+	 * Setup Multipurpose Input/Output pins.
+	 */
+	if (idx == 0) {
+		switch (pcidev->device) {
+		case PCI_DEVICE_ID_COMMTECH_4222PCI335:
+		case PCI_DEVICE_ID_COMMTECH_4224PCI335:
+			writeb(0x78, p + UART_EXAR_MPIOLVL_7_0);
+			writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
+			writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
+			break;
+		case PCI_DEVICE_ID_COMMTECH_2324PCI335:
+		case PCI_DEVICE_ID_COMMTECH_2328PCI335:
+			writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
+			writeb(0xc0, p + UART_EXAR_MPIOINV_7_0);
+			writeb(0xc0, p + UART_EXAR_MPIOSEL_7_0);
+			break;
+		}
+		writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
+		writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
+		writeb(0x00, p + UART_EXAR_MPIOOD_7_0);
+	}
+
+	return 0;
+}
+
+static int
+pci_connect_tech_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+		       struct uart_8250_port *port, int idx)
+{
+	unsigned int offset = idx * 0x200;
+	unsigned int baud = 1843200;
+
+	port->port.uartclk = baud * 16;
+	return default_setup(priv, pcidev, idx, offset, port);
+}
+
+static int
+pci_xr17c154_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+		   struct uart_8250_port *port, int idx)
+{
+	unsigned int offset = idx * 0x200;
+	unsigned int baud = 921600;
+
+	port->port.uartclk = baud * 16;
+	return default_setup(priv, pcidev, idx, offset, port);
+}
+
+static void setup_gpio(u8 __iomem *p)
+{
+	writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
+	writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
+	writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
+	writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
+	writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
+	writeb(0x00, p + UART_EXAR_MPIOOD_7_0);
+	writeb(0x00, p + UART_EXAR_MPIOINT_15_8);
+	writeb(0x00, p + UART_EXAR_MPIOLVL_15_8);
+	writeb(0x00, p + UART_EXAR_MPIO3T_15_8);
+	writeb(0x00, p + UART_EXAR_MPIOINV_15_8);
+	writeb(0x00, p + UART_EXAR_MPIOSEL_15_8);
+	writeb(0x00, p + UART_EXAR_MPIOOD_15_8);
+}
+
+static void *
+xr17v35x_register_gpio(struct pci_dev *pcidev)
+{
+	struct platform_device *pdev;
+
+	pdev = platform_device_alloc("gpio_exar", PLATFORM_DEVID_AUTO);
+	if (!pdev)
+		return NULL;
+
+	platform_set_drvdata(pdev, pcidev);
+	if (platform_device_add(pdev) < 0) {
+		platform_device_put(pdev);
+		return NULL;
+	}
+
+	return pdev;
+}
+
+static int
+pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+		   struct uart_8250_port *port, int idx)
+{
+	const struct exar8250_board *board = priv->board;
+	unsigned int offset = idx * 0x400;
+	unsigned int baud = 7812500;
+	u8 __iomem *p;
+	int ret;
+
+	port->port.uartclk = baud * 16;
+	/*
+	 * Setup the uart clock for the devices on expansion slot to
+	 * half the clock speed of the main chip (which is 125MHz)
+	 */
+	if (board->has_slave && idx >= 8)
+		port->port.uartclk /= 2;
+
+	ret = default_setup(priv, pcidev, idx, offset, port);
+	if (ret)
+		return ret;
+
+	p = port->port.membase;
+
+	writeb(0x00, p + UART_EXAR_8XMODE);
+	writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR);
+	writeb(128, p + UART_EXAR_TXTRG);
+	writeb(128, p + UART_EXAR_RXTRG);
+
+	if (idx == 0) {
+		/* Setup Multipurpose Input/Output pins. */
+		setup_gpio(p);
+
+		port->port.private_data = xr17v35x_register_gpio(pcidev);
+	}
+
+	return 0;
+}
+
+static void pci_xr17v35x_exit(struct pci_dev *pcidev)
+{
+	struct exar8250 *priv = pci_get_drvdata(pcidev);
+	struct uart_8250_port *port = serial8250_get_port(priv->line[0]);
+	struct platform_device *pdev = port->port.private_data;
+
+	platform_device_unregister(pdev);
+	port->port.private_data = NULL;
+}
+
+static int
+exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent)
+{
+	unsigned int nr_ports, i, bar = 0, maxnr;
+	struct exar8250_board *board;
+	struct uart_8250_port uart;
+	struct exar8250 *priv;
+	int rc;
+
+	board = (struct exar8250_board *)ent->driver_data;
+	if (!board)
+		return -EINVAL;
+
+	rc = pcim_enable_device(pcidev);
+	if (rc)
+		return rc;
+
+	maxnr = pci_resource_len(pcidev, bar) >> (board->reg_shift + 3);
+
+	nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
+
+	priv = devm_kzalloc(&pcidev->dev, sizeof(*priv) +
+			    sizeof(unsigned int) * nr_ports,
+			    GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->board = board;
+
+	pci_set_master(pcidev);
+
+	rc = pci_alloc_irq_vectors(pcidev, 1, 1, PCI_IRQ_ALL_TYPES);
+	if (rc < 0)
+		return rc;
+
+	memset(&uart, 0, sizeof(uart));
+	uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ
+			  | UPF_EXAR_EFR;
+	uart.port.irq = pci_irq_vector(pcidev, 0);
+	uart.port.dev = &pcidev->dev;
+
+	for (i = 0; i < nr_ports && i < maxnr; i++) {
+		rc = board->setup(priv, pcidev, &uart, i);
+		if (rc) {
+			dev_err(&pcidev->dev, "Failed to setup port %u\n", i);
+			break;
+		}
+
+		dev_dbg(&pcidev->dev, "Setup PCI port: port %lx, irq %d, type %d\n",
+			uart.port.iobase, uart.port.irq, uart.port.iotype);
+
+		priv->line[i] = serial8250_register_8250_port(&uart);
+		if (priv->line[i] < 0) {
+			dev_err(&pcidev->dev,
+				"Couldn't register serial port %lx, irq %d, type %d, error %d\n",
+				uart.port.iobase, uart.port.irq,
+				uart.port.iotype, priv->line[i]);
+			break;
+		}
+	}
+	priv->nr = i;
+	pci_set_drvdata(pcidev, priv);
+	return 0;
+}
+
+static void exar_pci_remove(struct pci_dev *pcidev)
+{
+	struct exar8250 *priv = pci_get_drvdata(pcidev);
+	unsigned int i;
+
+	for (i = 0; i < priv->nr; i++)
+		serial8250_unregister_port(priv->line[i]);
+
+	if (priv->board->exit)
+		priv->board->exit(pcidev);
+}
+
+static int __maybe_unused exar_suspend(struct device *dev)
+{
+	struct pci_dev *pcidev = to_pci_dev(dev);
+	struct exar8250 *priv = pci_get_drvdata(pcidev);
+	unsigned int i;
+
+	for (i = 0; i < priv->nr; i++)
+		if (priv->line[i] >= 0)
+			serial8250_suspend_port(priv->line[i]);
+
+	/* Ensure that every init quirk is properly torn down */
+	if (priv->board->exit)
+		priv->board->exit(pcidev);
+
+	return 0;
+}
+
+static int __maybe_unused exar_resume(struct device *dev)
+{
+	struct pci_dev *pcidev = to_pci_dev(dev);
+	struct exar8250 *priv = pci_get_drvdata(pcidev);
+	unsigned int i;
+
+	for (i = 0; i < priv->nr; i++)
+		if (priv->line[i] >= 0)
+			serial8250_resume_port(priv->line[i]);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(exar_pci_pm, exar_suspend, exar_resume);
+
+static const struct exar8250_board pbn_fastcom335_2 = {
+	.num_ports	= 2,
+	.setup		= pci_fastcom335_setup,
+};
+
+static const struct exar8250_board pbn_fastcom335_4 = {
+	.num_ports	= 4,
+	.setup		= pci_fastcom335_setup,
+};
+
+static const struct exar8250_board pbn_fastcom335_8 = {
+	.num_ports	= 8,
+	.setup		= pci_fastcom335_setup,
+};
+
+static const struct exar8250_board pbn_connect = {
+	.setup		= pci_connect_tech_setup,
+};
+
+static const struct exar8250_board pbn_exar_ibm_saturn = {
+	.num_ports	= 1,
+	.setup		= pci_xr17c154_setup,
+};
+
+static const struct exar8250_board pbn_exar_XR17C15x = {
+	.setup		= pci_xr17c154_setup,
+};
+
+static const struct exar8250_board pbn_exar_XR17V35x = {
+	.setup		= pci_xr17v35x_setup,
+	.exit		= pci_xr17v35x_exit,
+};
+
+static const struct exar8250_board pbn_exar_XR17V4358 = {
+	.num_ports	= 12,
+	.has_slave	= true,
+	.setup		= pci_xr17v35x_setup,
+	.exit		= pci_xr17v35x_exit,
+};
+
+static const struct exar8250_board pbn_exar_XR17V8358 = {
+	.num_ports	= 16,
+	.has_slave	= true,
+	.setup		= pci_xr17v35x_setup,
+	.exit		= pci_xr17v35x_exit,
+};
+
+#define CONNECT_DEVICE(devid, sdevid, bd) {				\
+	PCI_DEVICE_SUB(							\
+		PCI_VENDOR_ID_EXAR,					\
+		PCI_DEVICE_ID_EXAR_##devid,				\
+		PCI_SUBVENDOR_ID_CONNECT_TECH,				\
+		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_##sdevid), 0, 0,	\
+		(kernel_ulong_t)&bd					\
+	}
+
+#define EXAR_DEVICE(vend, devid, bd) {					\
+	PCI_VDEVICE(vend, PCI_DEVICE_ID_##devid), (kernel_ulong_t)&bd	\
+	}
+
+#define IBM_DEVICE(devid, sdevid, bd) {			\
+	PCI_DEVICE_SUB(					\
+		PCI_VENDOR_ID_EXAR,			\
+		PCI_DEVICE_ID_EXAR_##devid,		\
+		PCI_VENDOR_ID_IBM,			\
+		PCI_SUBDEVICE_ID_IBM_##sdevid), 0, 0,	\
+		(kernel_ulong_t)&bd			\
+	}
+
+static struct pci_device_id exar_pci_tbl[] = {
+	CONNECT_DEVICE(XR17C152, UART_2_232, pbn_connect),
+	CONNECT_DEVICE(XR17C154, UART_4_232, pbn_connect),
+	CONNECT_DEVICE(XR17C158, UART_8_232, pbn_connect),
+	CONNECT_DEVICE(XR17C152, UART_1_1, pbn_connect),
+	CONNECT_DEVICE(XR17C154, UART_2_2, pbn_connect),
+	CONNECT_DEVICE(XR17C158, UART_4_4, pbn_connect),
+	CONNECT_DEVICE(XR17C152, UART_2, pbn_connect),
+	CONNECT_DEVICE(XR17C154, UART_4, pbn_connect),
+	CONNECT_DEVICE(XR17C158, UART_8, pbn_connect),
+	CONNECT_DEVICE(XR17C152, UART_2_485, pbn_connect),
+	CONNECT_DEVICE(XR17C154, UART_4_485, pbn_connect),
+	CONNECT_DEVICE(XR17C158, UART_8_485, pbn_connect),
+
+	IBM_DEVICE(XR17C152, SATURN_SERIAL_ONE_PORT, pbn_exar_ibm_saturn),
+
+	/* Exar Corp. XR17C15[248] Dual/Quad/Octal UART */
+	EXAR_DEVICE(EXAR, EXAR_XR17C152, pbn_exar_XR17C15x),
+	EXAR_DEVICE(EXAR, EXAR_XR17C154, pbn_exar_XR17C15x),
+	EXAR_DEVICE(EXAR, EXAR_XR17C158, pbn_exar_XR17C15x),
+
+	/* Exar Corp. XR17V[48]35[248] Dual/Quad/Octal/Hexa PCIe UARTs */
+	EXAR_DEVICE(EXAR, EXAR_XR17V352, pbn_exar_XR17V35x),
+	EXAR_DEVICE(EXAR, EXAR_XR17V354, pbn_exar_XR17V35x),
+	EXAR_DEVICE(EXAR, EXAR_XR17V358, pbn_exar_XR17V35x),
+	EXAR_DEVICE(EXAR, EXAR_XR17V4358, pbn_exar_XR17V4358),
+	EXAR_DEVICE(EXAR, EXAR_XR17V8358, pbn_exar_XR17V8358),
+	EXAR_DEVICE(COMMTECH, COMMTECH_4222PCIE, pbn_exar_XR17V35x),
+	EXAR_DEVICE(COMMTECH, COMMTECH_4224PCIE, pbn_exar_XR17V35x),
+	EXAR_DEVICE(COMMTECH, COMMTECH_4228PCIE, pbn_exar_XR17V35x),
+
+	EXAR_DEVICE(COMMTECH, COMMTECH_4222PCI335, pbn_fastcom335_2),
+	EXAR_DEVICE(COMMTECH, COMMTECH_4224PCI335, pbn_fastcom335_4),
+	EXAR_DEVICE(COMMTECH, COMMTECH_2324PCI335, pbn_fastcom335_4),
+	EXAR_DEVICE(COMMTECH, COMMTECH_2328PCI335, pbn_fastcom335_8),
+	{ 0, }
+};
+MODULE_DEVICE_TABLE(pci, exar_pci_tbl);
+
+static struct pci_driver exar_pci_driver = {
+	.name		= "exar_serial",
+	.probe		= exar_pci_probe,
+	.remove		= exar_pci_remove,
+	.driver         = {
+		.pm     = &exar_pci_pm,
+	},
+	.id_table	= exar_pci_tbl,
+};
+module_pci_driver(exar_pci_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Exar Serial Dricer");
+MODULE_AUTHOR("Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>");
diff --git a/drivers/tty/serial/8250/8250_gsc.c b/drivers/tty/serial/8250/8250_gsc.c
index b1e6ae9f1ff9..63306de4390d 100644
--- a/drivers/tty/serial/8250/8250_gsc.c
+++ b/drivers/tty/serial/8250/8250_gsc.c
@@ -60,6 +60,10 @@ static int __init serial_init_chip(struct parisc_device *dev)
 					7272727 : 1843200;
 	uart.port.mapbase	= address;
 	uart.port.membase	= ioremap_nocache(address, 16);
+	if (!uart.port.membase) {
+		dev_warn(&dev->dev, "Failed to map memory\n");
+		return -ENOMEM;
+	}
 	uart.port.irq	= dev->irq;
 	uart.port.flags	= UPF_BOOT_AUTOCONF;
 	uart.port.dev	= &dev->dev;
diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c
index 38166db2b824..115190b7962a 100644
--- a/drivers/tty/serial/8250/8250_hp300.c
+++ b/drivers/tty/serial/8250/8250_hp300.c
@@ -19,7 +19,7 @@
 
 #include "8250.h"
 
-#if !defined(CONFIG_HPDCA) && !defined(CONFIG_HPAPCI)
+#if !defined(CONFIG_HPDCA) && !defined(CONFIG_HPAPCI) && !defined(CONFIG_COMPILE_TEST)
 #warning CONFIG_SERIAL_8250 defined but neither CONFIG_HPDCA nor CONFIG_HPAPCI defined, are you sure?
 #endif
 
diff --git a/drivers/tty/serial/8250/8250_lpss.c b/drivers/tty/serial/8250/8250_lpss.c
index 58cbb30a9401..f3ea90f0e411 100644
--- a/drivers/tty/serial/8250/8250_lpss.c
+++ b/drivers/tty/serial/8250/8250_lpss.c
@@ -332,10 +332,10 @@ static void lpss8250_remove(struct pci_dev *pdev)
 {
 	struct lpss8250 *lpss = pci_get_drvdata(pdev);
 
+	serial8250_unregister_port(lpss->line);
+
 	if (lpss->board->exit)
 		lpss->board->exit(lpss);
-
-	serial8250_unregister_port(lpss->line);
 }
 
 static const struct lpss8250_board byt_board = {
diff --git a/drivers/tty/serial/8250/8250_mid.c b/drivers/tty/serial/8250/8250_mid.c
index ac013edf4992..ec957cce8c9a 100644
--- a/drivers/tty/serial/8250/8250_mid.c
+++ b/drivers/tty/serial/8250/8250_mid.c
@@ -75,6 +75,37 @@ static int pnw