staging: comedi: s626: cleanup comments in s626_initialize()

Cleanup the comments to follow the coding style of the kernel.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1 files changed, 88 insertions, 81 deletions

diff --git a/drivers/staging/comedi/drivers/s626.c b/drivers/staging/comedi/drivers/s626.c
index 6f1705ba60e2..e1d10f366c2f 100644
--- a/drivers/staging/comedi/drivers/s626.c
+++ b/drivers/staging/comedi/drivers/s626.c
@@ -2461,83 +2461,80 @@ static void s626_initialize(struct comedi_device *dev)
 	uint16_t chan;
 	int i;
 
-	/*  enab DEBI and audio pins, enable I2C interface. */
+	/* Enable DEBI and audio pins, enable I2C interface */
 	MC_ENABLE(P_MC1, MC1_DEBI | MC1_AUDIO | MC1_I2C);
-	/*  Configure DEBI operating mode. */
-	WR7146(P_DEBICFG, DEBI_CFG_SLAVE16	/*  Local bus is 16 */
-	       /*  bits wide. */
-	       | (DEBI_TOUT << DEBI_CFG_TOUT_BIT)
-
-	       /*  Declare DEBI */
-	       /*  transfer timeout */
-	       /*  interval. */
-	       |DEBI_SWAP	/*  Set up byte lane */
-	       /*  steering. */
-	       | DEBI_CFG_INTEL);	/*  Intel-compatible */
-	/*  local bus (DEBI */
-	/*  never times out). */
-
-	/* DEBI INIT S626 WR7146( P_DEBICFG, DEBI_CFG_INTEL | DEBI_CFG_TOQ */
-	/* | DEBI_CFG_INCQ| DEBI_CFG_16Q); //end */
-
-	/*  Paging is disabled. */
-	WR7146(P_DEBIPAGE, DEBI_PAGE_DISABLE);	/*  Disable MMU paging. */
-
-	/*  Init GPIO so that ADC Start* is negated. */
+
+	/*
+	 *  Configure DEBI operating mode
+	 *
+	 *   Local bus is 16 bits wide
+	 *   Declare DEBI transfer timeout interval
+	 *   Set up byte lane steering
+	 *   Intel-compatible local bus (DEBI never times out)
+	 */
+	WR7146(P_DEBICFG, DEBI_CFG_SLAVE16 |
+			  (DEBI_TOUT << DEBI_CFG_TOUT_BIT) |
+			  DEBI_SWAP | DEBI_CFG_INTEL);
+
+	/* Disable MMU paging */
+	WR7146(P_DEBIPAGE, DEBI_PAGE_DISABLE);
+
+	/* Init GPIO so that ADC Start* is negated */
 	WR7146(P_GPIO, GPIO_BASE | GPIO1_HI);
 
 	/* I2C device address for onboard eeprom (revb) */
 	devpriv->I2CAdrs = 0xA0;
 
-	/*  Issue an I2C ABORT command to halt any I2C operation in */
-	/* progress and reset BUSY flag. */
+	/*
+	 * Issue an I2C ABORT command to halt any I2C
+	 * operation in progress and reset BUSY flag.
+	 */
 	WR7146(P_I2CSTAT, I2C_CLKSEL | I2C_ABORT);
-	/*  Write I2C control: abort any I2C activity. */
 	MC_ENABLE(P_MC2, MC2_UPLD_IIC);
-	/*  Invoke command  upload */
 	while ((RR7146(P_MC2) & MC2_UPLD_IIC) == 0)
 		;
-	/*  and wait for upload to complete. */
 
-	/* Per SAA7146 data sheet, write to STATUS reg twice to
-	 * reset all  I2C error flags. */
+	/*
+	 * Per SAA7146 data sheet, write to STATUS
+	 * reg twice to reset all  I2C error flags.
+	 */
 	for (i = 0; i < 2; i++) {
 		WR7146(P_I2CSTAT, I2C_CLKSEL);
-		/*  Write I2C control: reset  error flags. */
-		MC_ENABLE(P_MC2, MC2_UPLD_IIC);	/*  Invoke command upload */
+		MC_ENABLE(P_MC2, MC2_UPLD_IIC);
 		while (!MC_TEST(P_MC2, MC2_UPLD_IIC))
 			;
-		/* and wait for upload to complete. */
 	}
 
-	/* Init audio interface functional attributes: set DAC/ADC
+	/*
+	 * Init audio interface functional attributes: set DAC/ADC
 	 * serial clock rates, invert DAC serial clock so that
 	 * DAC data setup times are satisfied, enable DAC serial
 	 * clock out.
 	 */
-
 	WR7146(P_ACON2, ACON2_INIT);
 
-	/* Set up TSL1 slot list, which is used to control the
+	/*
+	 * Set up TSL1 slot list, which is used to control the
 	 * accumulation of ADC data: RSD1 = shift data in on SD1.
-	 * SIB_A1  = store data uint8_t at next available location in
-	 * FB BUFFER1  register. */
+	 * SIB_A1  = store data uint8_t at next available location
+	 * in FB BUFFER1 register.
+	 */
 	WR7146(P_TSL1, RSD1 | SIB_A1);
-	/*  Fetch ADC high data uint8_t. */
 	WR7146(P_TSL1 + 4, RSD1 | SIB_A1 | EOS);
-	/*  Fetch ADC low data uint8_t; end of TSL1. */
 
-	/*  enab TSL1 slot list so that it executes all the time. */
+	/* Enable TSL1 slot list so that it executes all the time */
 	WR7146(P_ACON1, ACON1_ADCSTART);
 
-	/*  Initialize RPS registers used for ADC. */
-
-	/* Physical start of RPS program. */
-	WR7146(P_RPSADDR1, (uint32_t) devpriv->RPSBuf.PhysicalBase);
+	/*
+	 * Initialize RPS registers used for ADC
+	 */
 
+	/* Physical start of RPS program */
+	WR7146(P_RPSADDR1, (uint32_t)devpriv->RPSBuf.PhysicalBase);
+	/* RPS program performs no explicit mem writes */
 	WR7146(P_RPSPAGE1, 0);
-	/*  RPS program performs no explicit mem writes. */
-	WR7146(P_RPS1_TOUT, 0);	/*  Disable RPS timeouts. */
+	/* Disable RPS timeouts */
+	WR7146(P_RPS1_TOUT, 0);
 
 #if 0
 	/*
@@ -2584,39 +2581,45 @@ static void s626_initialize(struct comedi_device *dev)
 	}
 #endif	/* SAA7146 BUG WORKAROUND */
 
-	/*  end initADC */
-
-	/*  init the DAC interface */
+	/*
+	 * Initialize the DAC interface
+	 */
 
-	/* Init Audio2's output DMAC attributes: burst length = 1
-	 * DWORD,  threshold = 1 DWORD.
+	/*
+	 * Init Audio2's output DMAC attributes:
+	 *   burst length = 1 DWORD
+	 *   threshold = 1 DWORD.
 	 */
 	WR7146(P_PCI_BT_A, 0);
 
-	/* Init Audio2's output DMA physical addresses.  The protection
+	/*
+	 * Init Audio2's output DMA physical addresses.  The protection
 	 * address is set to 1 DWORD past the base address so that a
 	 * single DWORD will be transferred each time a DMA transfer is
-	 * enabled. */
-
+	 * enabled.
+	 */
 	pPhysBuf = devpriv->ANABuf.PhysicalBase +
 		   (DAC_WDMABUF_OS * sizeof(uint32_t));
+	WR7146(P_BASEA2_OUT, (uint32_t) pPhysBuf);
+	WR7146(P_PROTA2_OUT, (uint32_t) (pPhysBuf + sizeof(uint32_t)));
 
-	WR7146(P_BASEA2_OUT, (uint32_t) pPhysBuf);	/*  Buffer base adrs. */
-	WR7146(P_PROTA2_OUT, (uint32_t) (pPhysBuf + sizeof(uint32_t)));	/*  Protection address. */
-
-	/* Cache Audio2's output DMA buffer logical address.  This is
-	 * where DAC data is buffered for A2 output DMA transfers. */
+	/*
+	 * Cache Audio2's output DMA buffer logical address.  This is
+	 * where DAC data is buffered for A2 output DMA transfers.
+	 */
 	devpriv->pDacWBuf = (uint32_t *)devpriv->ANABuf.LogicalBase +
 			    DAC_WDMABUF_OS;
 
-	/* Audio2's output channels does not use paging.  The protection
-	 * violation handling bit is set so that the DMAC will
-	 * automatically halt and its PCI address pointer will be reset
-	 * when the protection address is reached. */
-
+	/*
+	 * Audio2's output channels does not use paging.  The
+	 * protection violation handling bit is set so that the
+	 * DMAC will automatically halt and its PCI address pointer
+	 * will be reset when the protection address is reached.
+	 */
 	WR7146(P_PAGEA2_OUT, 8);
 
-	/* Initialize time slot list 2 (TSL2), which is used to control
+	/*
+	 * Initialize time slot list 2 (TSL2), which is used to control
 	 * the clock generation for and serialization of data to be sent
 	 * to the DAC devices.  Slot 0 is a NOP that is used to trap TSL
 	 * execution; this permits other slots to be safely modified
@@ -2627,48 +2630,52 @@ static void s626_initialize(struct comedi_device *dev)
 	 * not yet finished executing.
 	 */
 
+	/* Slot 0: Trap TSL execution, shift 0xFF into FB_BUFFER2 */
 	SETVECT(0, XSD2 | RSD3 | SIB_A2 | EOS);
-	/*  Slot 0: Trap TSL execution, shift 0xFF into FB_BUFFER2. */
 
-	/* Initialize slot 1, which is constant.  Slot 1 causes a
+	/*
+	 * Initialize slot 1, which is constant.  Slot 1 causes a
 	 * DWORD to be transferred from audio channel 2's output FIFO
 	 * to the FIFO's output buffer so that it can be serialized
 	 * and sent to the DAC during subsequent slots.  All remaining
 	 * slots are dynamically populated as required by the target
 	 * DAC device.
 	 */
+
+	/* Slot 1: Fetch DWORD from Audio2's output FIFO */
 	SETVECT(1, LF_A2);
-	/*  Slot 1: Fetch DWORD from Audio2's output FIFO. */
 
-	/*  Start DAC's audio interface (TSL2) running. */
+	/* Start DAC's audio interface (TSL2) running */
 	WR7146(P_ACON1, ACON1_DACSTART);
 
-	/* end init DAC interface */
-
-	/* Init Trim DACs to calibrated values.  Do it twice because the
+	/*
+	 * Init Trim DACs to calibrated values.  Do it twice because the
 	 * SAA7146 audio channel does not always reset properly and
 	 * sometimes causes the first few TrimDAC writes to malfunction.
 	 */
-
 	LoadTrimDACs(dev);
-	LoadTrimDACs(dev);	/*  Insurance. */
+	LoadTrimDACs(dev);
 
-	/* Manually init all gate array hardware in case this is a soft
+	/*
+	 * Manually init all gate array hardware in case this is a soft
 	 * reset (we have no way of determining whether this is a warm
 	 * or cold start).  This is necessary because the gate array will
 	 * reset only in response to a PCI hard reset; there is no soft
-	 * reset function. */
+	 * reset function.
+	 */
 
-	/* Init all DAC outputs to 0V and init all DAC setpoint and
+	/*
+	 * Init all DAC outputs to 0V and init all DAC setpoint and
 	 * polarity images.
 	 */
 	for (chan = 0; chan < S626_DAC_CHANNELS; chan++)
 		SetDAC(dev, chan, 0);
 
-	/*  Init counters. */
+	/* Init counters */
 	CountersInit(dev);
 
-	/* Without modifying the state of the Battery Backup enab, disable
+	/*
+	 * Without modifying the state of the Battery Backup enab, disable
 	 * the watchdog timer, set DIO channels 0-5 to operate in the
 	 * standard DIO (vs. counter overflow) mode, disable the battery
 	 * charger, and reset the watchdog interval selector to zero.
@@ -2676,11 +2683,11 @@ static void s626_initialize(struct comedi_device *dev)
 	WriteMISC2(dev, (uint16_t)(DEBIread(dev, LP_RDMISC2) &
 				   MISC2_BATT_ENABLE));
 
-	/*  Initialize the digital I/O subsystem. */
+	/* Initialize the digital I/O subsystem */
 	s626_dio_init(dev);
 
 	/* enable interrupt test */
-	/*  writel(IRQ_GPIO3 | IRQ_RPS1,devpriv->base_addr+P_IER); */
+	/* writel(IRQ_GPIO3 | IRQ_RPS1, devpriv->base_addr + P_IER); */
 }
 
 static int s626_attach_pci(struct comedi_device *dev, struct pci_dev *pcidev)