Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 2080 insertions, 0 deletions

diff --git a/drivers/macintosh/therm_pm72.c b/drivers/macintosh/therm_pm72.c
new file mode 100644
index 000000000000..82336a5a5474
--- /dev/null
+++ b/drivers/macintosh/therm_pm72.c
@@ -0,0 +1,2080 @@
+/*
+ * Device driver for the thermostats & fan controller of  the
+ * Apple G5 "PowerMac7,2" desktop machines.
+ *
+ * (c) Copyright IBM Corp. 2003-2004
+ *
+ * Maintained by: Benjamin Herrenschmidt
+ *                <benh@kernel.crashing.org>
+ * 
+ *
+ * The algorithm used is the PID control algorithm, used the same
+ * way the published Darwin code does, using the same values that
+ * are present in the Darwin 7.0 snapshot property lists.
+ *
+ * As far as the CPUs control loops are concerned, I use the
+ * calibration & PID constants provided by the EEPROM,
+ * I do _not_ embed any value from the property lists, as the ones
+ * provided by Darwin 7.0 seem to always have an older version that
+ * what I've seen on the actual computers.
+ * It would be interesting to verify that though. Darwin has a
+ * version code of 1.0.0d11 for all control loops it seems, while
+ * so far, the machines EEPROMs contain a dataset versioned 1.0.0f
+ *
+ * Darwin doesn't provide source to all parts, some missing
+ * bits like the AppleFCU driver or the actual scale of some
+ * of the values returned by sensors had to be "guessed" some
+ * way... or based on what Open Firmware does.
+ *
+ * I didn't yet figure out how to get the slots power consumption
+ * out of the FCU, so that part has not been implemented yet and
+ * the slots fan is set to a fixed 50% PWM, hoping this value is
+ * safe enough ...
+ *
+ * Note: I have observed strange oscillations of the CPU control
+ * loop on a dual G5 here. When idle, the CPU exhaust fan tend to
+ * oscillates slowly (over several minutes) between the minimum
+ * of 300RPMs and approx. 1000 RPMs. I don't know what is causing
+ * this, it could be some incorrect constant or an error in the
+ * way I ported the algorithm, or it could be just normal. I
+ * don't have full understanding on the way Apple tweaked the PID
+ * algorithm for the CPU control, it is definitely not a standard
+ * implementation...
+ *
+ * TODO:  - Check MPU structure version/signature
+ *        - Add things like /sbin/overtemp for non-critical
+ *          overtemp conditions so userland can take some policy
+ *          decisions, like slewing down CPUs
+ *	  - Deal with fan and i2c failures in a better way
+ *	  - Maybe do a generic PID based on params used for
+ *	    U3 and Drives ? Definitely need to factor code a bit
+ *          bettter... also make sensor detection more robust using
+ *          the device-tree to probe for them
+ *        - Figure out how to get the slots consumption and set the
+ *          slots fan accordingly
+ *
+ * History:
+ *
+ *  Nov. 13, 2003 : 0.5
+ *	- First release
+ *
+ *  Nov. 14, 2003 : 0.6
+ *	- Read fan speed from FCU, low level fan routines now deal
+ *	  with errors & check fan status, though higher level don't
+ *	  do much.
+ *	- Move a bunch of definitions to .h file
+ *
+ *  Nov. 18, 2003 : 0.7
+ *	- Fix build on ppc64 kernel
+ *	- Move back statics definitions to .c file
+ *	- Avoid calling schedule_timeout with a negative number
+ *
+ *  Dec. 18, 2003 : 0.8
+ *	- Fix typo when reading back fan speed on 2 CPU machines
+ *
+ *  Mar. 11, 2004 : 0.9
+ *	- Rework code accessing the ADC chips, make it more robust and
+ *	  closer to the chip spec. Also make sure it is configured properly,
+ *        I've seen yet unexplained cases where on startup, I would have stale
+ *        values in the configuration register
+ *	- Switch back to use of target fan speed for PID, thus lowering
+ *        pressure on i2c
+ *
+ *  Oct. 20, 2004 : 1.1
+ *	- Add device-tree lookup for fan IDs, should detect liquid cooling
+ *        pumps when present
+ *	- Enable driver for PowerMac7,3 machines
+ *	- Split the U3/Backside cooling on U3 & U3H versions as Darwin does
+ *	- Add new CPU cooling algorithm for machines with liquid cooling
+ *	- Workaround for some PowerMac7,3 with empty "fan" node in the devtree
+ *	- Fix a signed/unsigned compare issue in some PID loops
+ *
+ *  Mar. 10, 2005 : 1.2
+ *	- Add basic support for Xserve G5
+ *	- Retreive pumps min/max from EEPROM image in device-tree (broken)
+ *	- Use min/max macros here or there
+ *	- Latest darwin updated U3H min fan speed to 20% PWM
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/sched.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/smp_lock.h>
+#include <linux/wait.h>
+#include <linux/reboot.h>
+#include <linux/kmod.h>
+#include <linux/i2c.h>
+#include <linux/i2c-dev.h>
+#include <asm/prom.h>
+#include <asm/machdep.h>
+#include <asm/io.h>
+#include <asm/system.h>
+#include <asm/sections.h>
+#include <asm/of_device.h>
+
+#include "therm_pm72.h"
+
+#define VERSION "1.2b2"
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DBG(args...)	printk(args)
+#else
+#define DBG(args...)	do { } while(0)
+#endif
+
+
+/*
+ * Driver statics
+ */
+
+static struct of_device *		of_dev;
+static struct i2c_adapter *		u3_0;
+static struct i2c_adapter *		u3_1;
+static struct i2c_adapter *		k2;
+static struct i2c_client *		fcu;
+static struct cpu_pid_state		cpu_state[2];
+static struct basckside_pid_params	backside_params;
+static struct backside_pid_state	backside_state;
+static struct drives_pid_state		drives_state;
+static struct dimm_pid_state		dimms_state;
+static int				state;
+static int				cpu_count;
+static int				cpu_pid_type;
+static pid_t				ctrl_task;
+static struct completion		ctrl_complete;
+static int				critical_state;
+static int				rackmac;
+static s32				dimm_output_clamp;
+
+static DECLARE_MUTEX(driver_lock);
+
+/*
+ * We have 3 types of CPU PID control. One is "split" old style control
+ * for intake & exhaust fans, the other is "combined" control for both
+ * CPUs that also deals with the pumps when present. To be "compatible"
+ * with OS X at this point, we only use "COMBINED" on the machines that
+ * are identified as having the pumps (though that identification is at
+ * least dodgy). Ultimately, we could probably switch completely to this
+ * algorithm provided we hack it to deal with the UP case
+ */
+#define CPU_PID_TYPE_SPLIT	0
+#define CPU_PID_TYPE_COMBINED	1
+#define CPU_PID_TYPE_RACKMAC	2
+
+/*
+ * This table describes all fans in the FCU. The "id" and "type" values
+ * are defaults valid for all earlier machines. Newer machines will
+ * eventually override the table content based on the device-tree
+ */
+struct fcu_fan_table
+{
+	char*	loc;	/* location code */
+	int	type;	/* 0 = rpm, 1 = pwm, 2 = pump */
+	int	id;	/* id or -1 */
+};
+
+#define FCU_FAN_RPM		0
+#define FCU_FAN_PWM		1
+
+#define FCU_FAN_ABSENT_ID	-1
+
+#define FCU_FAN_COUNT		ARRAY_SIZE(fcu_fans)
+
+struct fcu_fan_table	fcu_fans[] = {
+	[BACKSIDE_FAN_PWM_INDEX] = {
+		.loc	= "BACKSIDE,SYS CTRLR FAN",
+		.type	= FCU_FAN_PWM,
+		.id	= BACKSIDE_FAN_PWM_DEFAULT_ID,
+	},
+	[DRIVES_FAN_RPM_INDEX] = {
+		.loc	= "DRIVE BAY",
+		.type	= FCU_FAN_RPM,
+		.id	= DRIVES_FAN_RPM_DEFAULT_ID,
+	},
+	[SLOTS_FAN_PWM_INDEX] = {
+		.loc	= "SLOT,PCI FAN",
+		.type	= FCU_FAN_PWM,
+		.id	= SLOTS_FAN_PWM_DEFAULT_ID,
+	},
+	[CPUA_INTAKE_FAN_RPM_INDEX] = {
+		.loc	= "CPU A INTAKE",
+		.type	= FCU_FAN_RPM,
+		.id	= CPUA_INTAKE_FAN_RPM_DEFAULT_ID,
+	},
+	[CPUA_EXHAUST_FAN_RPM_INDEX] = {
+		.loc	= "CPU A EXHAUST",
+		.type	= FCU_FAN_RPM,
+		.id	= CPUA_EXHAUST_FAN_RPM_DEFAULT_ID,
+	},
+	[CPUB_INTAKE_FAN_RPM_INDEX] = {
+		.loc	= "CPU B INTAKE",
+		.type	= FCU_FAN_RPM,
+		.id	= CPUB_INTAKE_FAN_RPM_DEFAULT_ID,
+	},
+	[CPUB_EXHAUST_FAN_RPM_INDEX] = {
+		.loc	= "CPU B EXHAUST",
+		.type	= FCU_FAN_RPM,
+		.id	= CPUB_EXHAUST_FAN_RPM_DEFAULT_ID,
+	},
+	/* pumps aren't present by default, have to be looked up in the
+	 * device-tree
+	 */
+	[CPUA_PUMP_RPM_INDEX] = {
+		.loc	= "CPU A PUMP",
+		.type	= FCU_FAN_RPM,		
+		.id	= FCU_FAN_ABSENT_ID,
+	},
+	[CPUB_PUMP_RPM_INDEX] = {
+		.loc	= "CPU B PUMP",
+		.type	= FCU_FAN_RPM,
+		.id	= FCU_FAN_ABSENT_ID,
+	},
+	/* Xserve fans */
+	[CPU_A1_FAN_RPM_INDEX] = {
+		.loc	= "CPU A 1",
+		.type	= FCU_FAN_RPM,
+		.id	= FCU_FAN_ABSENT_ID,
+	},
+	[CPU_A2_FAN_RPM_INDEX] = {
+		.loc	= "CPU A 2",
+		.type	= FCU_FAN_RPM,
+		.id	= FCU_FAN_ABSENT_ID,
+	},
+	[CPU_A3_FAN_RPM_INDEX] = {
+		.loc	= "CPU A 3",
+		.type	= FCU_FAN_RPM,
+		.id	= FCU_FAN_ABSENT_ID,
+	},
+	[CPU_B1_FAN_RPM_INDEX] = {
+		.loc	= "CPU B 1",
+		.type	= FCU_FAN_RPM,
+		.id	= FCU_FAN_ABSENT_ID,
+	},
+	[CPU_B2_FAN_RPM_INDEX] = {
+		.loc	= "CPU B 2",
+		.type	= FCU_FAN_RPM,
+		.id	= FCU_FAN_ABSENT_ID,
+	},
+	[CPU_B3_FAN_RPM_INDEX] = {
+		.loc	= "CPU B 3",
+		.type	= FCU_FAN_RPM,
+		.id	= FCU_FAN_ABSENT_ID,
+	},
+};
+
+/*
+ * i2c_driver structure to attach to the host i2c controller
+ */
+
+static int therm_pm72_attach(struct i2c_adapter *adapter);
+static int therm_pm72_detach(struct i2c_adapter *adapter);
+
+static struct i2c_driver therm_pm72_driver =
+{
+	.owner		= THIS_MODULE,
+	.name		= "therm_pm72",
+	.flags		= I2C_DF_NOTIFY,
+	.attach_adapter	= therm_pm72_attach,
+	.detach_adapter	= therm_pm72_detach,
+};
+
+/*
+ * Utility function to create an i2c_client structure and
+ * attach it to one of u3 adapters
+ */
+static struct i2c_client *attach_i2c_chip(int id, const char *name)
+{
+	struct i2c_client *clt;
+	struct i2c_adapter *adap;
+
+	if (id & 0x200)
+		adap = k2;
+	else if (id & 0x100)
+		adap = u3_1;
+	else
+		adap = u3_0;
+	if (adap == NULL)
+		return NULL;
+
+	clt = kmalloc(sizeof(struct i2c_client), GFP_KERNEL);
+	if (clt == NULL)
+		return NULL;
+	memset(clt, 0, sizeof(struct i2c_client));
+
+	clt->addr = (id >> 1) & 0x7f;
+	clt->adapter = adap;
+	clt->driver = &therm_pm72_driver;
+	strncpy(clt->name, name, I2C_NAME_SIZE-1);
+
+	if (i2c_attach_client(clt)) {
+		printk(KERN_ERR "therm_pm72: Failed to attach to i2c ID 0x%x\n", id);
+		kfree(clt);
+		return NULL;
+	}
+	return clt;
+}
+
+/*
+ * Utility function to get rid of the i2c_client structure
+ * (will also detach from the adapter hopepfully)
+ */
+static void detach_i2c_chip(struct i2c_client *clt)
+{
+	i2c_detach_client(clt);
+	kfree(clt);
+}
+
+/*
+ * Here are the i2c chip access wrappers
+ */
+
+static void initialize_adc(struct cpu_pid_state *state)
+{
+	int rc;
+	u8 buf[2];
+
+	/* Read ADC the configuration register and cache it. We
+	 * also make sure Config2 contains proper values, I've seen
+	 * cases where we got stale grabage in there, thus preventing
+	 * proper reading of conv. values
+	 */
+
+	/* Clear Config2 */
+	buf[0] = 5;
+	buf[1] = 0;
+	i2c_master_send(state->monitor, buf, 2);
+
+	/* Read & cache Config1 */
+	buf[0] = 1;
+	rc = i2c_master_send(state->monitor, buf, 1);
+	if (rc > 0) {
+		rc = i2c_master_recv(state->monitor, buf, 1);
+		if (rc > 0) {
+			state->adc_config = buf[0];
+			DBG("ADC config reg: %02x\n", state->adc_config);
+			/* Disable shutdown mode */
+		       	state->adc_config &= 0xfe;
+			buf[0] = 1;
+			buf[1] = state->adc_config;
+			rc = i2c_master_send(state->monitor, buf, 2);
+		}
+	}
+	if (rc <= 0)
+		printk(KERN_ERR "therm_pm72: Error reading ADC config"
+		       " register !\n");
+}
+
+static int read_smon_adc(struct cpu_pid_state *state, int chan)
+{
+	int rc, data, tries = 0;
+	u8 buf[2];
+
+	for (;;) {
+		/* Set channel */
+		buf[0] = 1;
+		buf[1] = (state->adc_config & 0x1f) | (chan << 5);
+		rc = i2c_master_send(state->monitor, buf, 2);
+		if (rc <= 0)
+			goto error;
+		/* Wait for convertion */
+		msleep(1);
+		/* Switch to data register */
+		buf[0] = 4;
+		rc = i2c_master_send(state->monitor, buf, 1);
+		if (rc <= 0)
+			goto error;
+		/* Read result */
+		rc = i2c_master_recv(state->monitor, buf, 2);
+		if (rc < 0)
+			goto error;
+		data = ((u16)buf[0]) << 8 | (u16)buf[1];
+		return data >> 6;
+	error:
+		DBG("Error reading ADC, retrying...\n");
+		if (++tries > 10) {
+			printk(KERN_ERR "therm_pm72: Error reading ADC !\n");
+			return -1;
+		}
+		msleep(10);
+	}
+}
+
+static int read_lm87_reg(struct i2c_client * chip, int reg)
+{
+	int rc, tries = 0;
+	u8 buf;
+
+	for (;;) {
+		/* Set address */
+		buf = (u8)reg;
+		rc = i2c_master_send(chip, &buf, 1);
+		if (rc <= 0)
+			goto error;
+		rc = i2c_master_recv(chip, &buf, 1);
+		if (rc <= 0)
+			goto error;
+		return (int)buf;
+	error:
+		DBG("Error reading LM87, retrying...\n");
+		if (++tries > 10) {
+			printk(KERN_ERR "therm_pm72: Error reading LM87 !\n");
+			return -1;
+		}
+		msleep(10);
+	}
+}
+
+static int fan_read_reg(int reg, unsigned char *buf, int nb)
+{
+	int tries, nr, nw;
+
+	buf[0] = reg;
+	tries = 0;
+	for (;;) {
+		nw = i2c_master_send(fcu, buf, 1);
+		if (nw > 0 || (nw < 0 && nw != -EIO) || tries >= 100)
+			break;
+		msleep(10);
+		++tries;
+	}
+	if (nw <= 0) {
+		printk(KERN_ERR "Failure writing address to FCU: %d", nw);
+		return -EIO;
+	}
+	tries = 0;
+	for (;;) {
+		nr = i2c_master_recv(fcu, buf, nb);
+		if (nr > 0 || (nr < 0 && nr != ENODEV) || tries >= 100)
+			break;
+		msleep(10);
+		++tries;
+	}
+	if (nr <= 0)
+		printk(KERN_ERR "Failure reading data from FCU: %d", nw);
+	return nr;
+}
+
+static int fan_write_reg(int reg, const unsigned char *ptr, int nb)
+{
+	int tries, nw;
+	unsigned char buf[16];
+
+	buf[0] = reg;
+	memcpy(buf+1, ptr, nb);
+	++nb;
+	tries = 0;
+	for (;;) {
+		nw = i2c_master_send(fcu, buf, nb);
+		if (nw > 0 || (nw < 0 && nw != EIO) || tries >= 100)
+			break;
+		msleep(10);
+		++tries;
+	}
+	if (nw < 0)
+		printk(KERN_ERR "Failure writing to FCU: %d", nw);
+	return nw;
+}
+
+static int start_fcu(void)
+{
+	unsigned char buf = 0xff;
+	int rc;
+
+	rc = fan_write_reg(0xe, &buf, 1);
+	if (rc < 0)
+		return -EIO;
+	rc = fan_write_reg(0x2e, &buf, 1);
+	if (rc < 0)
+		return -EIO;
+	return 0;
+}
+
+static int set_rpm_fan(int fan_index, int rpm)
+{
+	unsigned char buf[2];
+	int rc, id;
+
+	if (fcu_fans[fan_index].type != FCU_FAN_RPM)
+		return -EINVAL;
+	id = fcu_fans[fan_index].id; 
+	if (id == FCU_FAN_ABSENT_ID)
+		return -EINVAL;
+
+	if (rpm < 300)
+		rpm = 300;
+	else if (rpm > 8191)
+		rpm = 8191;
+	buf[0] = rpm >> 5;
+	buf[1] = rpm << 3;
+	rc = fan_write_reg(0x10 + (id * 2), buf, 2);
+	if (rc < 0)
+		return -EIO;
+	return 0;
+}
+
+static int get_rpm_fan(int fan_index, int programmed)
+{
+	unsigned char failure;
+	unsigned char active;
+	unsigned char buf[2];
+	int rc, id, reg_base;
+
+	if (fcu_fans[fan_index].type != FCU_FAN_RPM)
+		return -EINVAL;
+	id = fcu_fans[fan_index].id; 
+	if (id == FCU_FAN_ABSENT_ID)
+		return -EINVAL;
+
+	rc = fan_read_reg(0xb, &failure, 1);
+	if (rc != 1)
+		return -EIO;
+	if ((failure & (1 << id)) != 0)
+		return -EFAULT;
+	rc = fan_read_reg(0xd, &active, 1);
+	if (rc != 1)
+		return -EIO;
+	if ((active & (1 << id)) == 0)
+		return -ENXIO;
+
+	/* Programmed value or real current speed */
+	reg_base = programmed ? 0x10 : 0x11;
+	rc = fan_read_reg(reg_base + (id * 2), buf, 2);
+	if (rc != 2)
+		return -EIO;
+
+	return (buf[0] << 5) | buf[1] >> 3;
+}
+
+static int set_pwm_fan(int fan_index, int pwm)
+{
+	unsigned char buf[2];
+	int rc, id;
+
+	if (fcu_fans[fan_index].type != FCU_FAN_PWM)
+		return -EINVAL;
+	id = fcu_fans[fan_index].id; 
+	if (id == FCU_FAN_ABSENT_ID)
+		return -EINVAL;
+
+	if (pwm < 10)
+		pwm = 10;
+	else if (pwm > 100)
+		pwm = 100;
+	pwm = (pwm * 2559) / 1000;
+	buf[0] = pwm;
+	rc = fan_write_reg(0x30 + (id * 2), buf, 1);
+	if (rc < 0)
+		return rc;
+	return 0;
+}
+
+static int get_pwm_fan(int fan_index)
+{
+	unsigned char failure;
+	unsigned char active;
+	unsigned char buf[2];
+	int rc, id;
+
+	if (fcu_fans[fan_index].type != FCU_FAN_PWM)
+		return -EINVAL;
+	id = fcu_fans[fan_index].id; 
+	if (id == FCU_FAN_ABSENT_ID)
+		return -EINVAL;
+
+	rc = fan_read_reg(0x2b, &failure, 1);
+	if (rc != 1)
+		return -EIO;
+	if ((failure & (1 << id)) != 0)
+		return -EFAULT;
+	rc = fan_read_reg(0x2d, &active, 1);
+	if (rc != 1)
+		return -EIO;
+	if ((active & (1 << id)) == 0)
+		return -ENXIO;
+
+	/* Programmed value or real current speed */
+	rc = fan_read_reg(0x30 + (id * 2), buf, 1);
+	if (rc != 1)
+		return -EIO;
+
+	return (buf[0] * 1000) / 2559;
+}
+
+/*
+ * Utility routine to read the CPU calibration EEPROM data
+ * from the device-tree
+ */
+static int read_eeprom(int cpu, struct mpu_data *out)
+{
+	struct device_node *np;
+	char nodename[64];
+	u8 *data;
+	int len;
+
+	/* prom.c routine for finding a node by path is a bit brain dead
+	 * and requires exact @xxx unit numbers. This is a bit ugly but
+	 * will work for these machines
+	 */
+	sprintf(nodename, "/u3@0,f8000000/i2c@f8001000/cpuid@a%d", cpu ? 2 : 0);
+	np = of_find_node_by_path(nodename);
+	if (np == NULL) {
+		printk(KERN_ERR "therm_pm72: Failed to retreive cpuid node from device-tree\n");
+		return -ENODEV;
+	}
+	data = (u8 *)get_property(np, "cpuid", &len);
+	if (data == NULL) {
+		printk(KERN_ERR "therm_pm72: Failed to retreive cpuid property from device-tree\n");
+		of_node_put(np);
+		return -ENODEV;
+	}
+	memcpy(out, data, sizeof(struct mpu_data));
+	of_node_put(np);
+	
+	return 0;
+}
+
+static void fetch_cpu_pumps_minmax(void)
+{
+	struct cpu_pid_state *state0 = &cpu_state[0];
+	struct cpu_pid_state *state1 = &cpu_state[1];
+	u16 pump_min = 0, pump_max = 0xffff;
+	u16 tmp[4];
+
+	/* Try to fetch pumps min/max infos from eeprom */
+
+	memcpy(&tmp, &state0->mpu.processor_part_num, 8);
+	if (tmp[0] != 0xffff && tmp[1] != 0xffff) {
+		pump_min = max(pump_min, tmp[0]);
+		pump_max = min(pump_max, tmp[1]);
+	}
+	if (tmp[2] != 0xffff && tmp[3] != 0xffff) {
+		pump_min = max(pump_min, tmp[2]);
+		pump_max = min(pump_max, tmp[3]);
+	}
+
+	/* Double check the values, this _IS_ needed as the EEPROM on
+	 * some dual 2.5Ghz G5s seem, at least, to have both min & max
+	 * same to the same value ... (grrrr)
+	 */
+	if (pump_min == pump_max || pump_min == 0 || pump_max == 0xffff) {
+		pump_min = CPU_PUMP_OUTPUT_MIN;
+		pump_max = CPU_PUMP_OUTPUT_MAX;
+	}
+
+	state0->pump_min = state1->pump_min = pump_min;
+	state0->pump_max = state1->pump_max = pump_max;
+}
+
+/* 
+ * Now, unfortunately, sysfs doesn't give us a nice void * we could
+ * pass around to the attribute functions, so we don't really have
+ * choice but implement a bunch of them...
+ *
+ * That sucks a bit, we take the lock because FIX32TOPRINT evaluates
+ * the input twice... I accept patches :)
+ */
+#define BUILD_SHOW_FUNC_FIX(name, data)				\
+static ssize_t show_##name(struct device *dev, char *buf)	\
+{								\
+	ssize_t r;						\
+	down(&driver_lock);					\
+	r = sprintf(buf, "%d.%03d", FIX32TOPRINT(data));	\
+	up(&driver_lock);					\
+	return r;						\
+}
+#define BUILD_SHOW_FUNC_INT(name, data)				\
+static ssize_t show_##name(struct device *dev, char *buf)	\
+{								\
+	return sprintf(buf, "%d", data);			\
+}
+
+BUILD_SHOW_FUNC_FIX(cpu0_temperature, cpu_state[0].last_temp)
+BUILD_SHOW_FUNC_FIX(cpu0_voltage, cpu_state[0].voltage)
+BUILD_SHOW_FUNC_FIX(cpu0_current, cpu_state[0].current_a)
+BUILD_SHOW_FUNC_INT(cpu0_exhaust_fan_rpm, cpu_state[0].rpm)
+BUILD_SHOW_FUNC_INT(cpu0_intake_fan_rpm, cpu_state[0].intake_rpm)
+
+BUILD_SHOW_FUNC_FIX(cpu1_temperature, cpu_state[1].last_temp)
+BUILD_SHOW_FUNC_FIX(cpu1_voltage, cpu_state[1].voltage)
+BUILD_SHOW_FUNC_FIX(cpu1_current, cpu_state[1].current_a)
+BUILD_SHOW_FUNC_INT(cpu1_exhaust_fan_rpm, cpu_state[1].rpm)
+BUILD_SHOW_FUNC_INT(cpu1_intake_fan_rpm, cpu_state[1].intake_rpm)
+
+BUILD_SHOW_FUNC_FIX(backside_temperature, backside_state.last_temp)
+BUILD_SHOW_FUNC_INT(backside_fan_pwm, backside_state.pwm)
+
+BUILD_SHOW_FUNC_FIX(drives_temperature, drives_state.last_temp)
+BUILD_SHOW_FUNC_INT(drives_fan_rpm, drives_state.rpm)
+
+BUILD_SHOW_FUNC_FIX(dimms_temperature, dimms_state.last_temp)
+
+static DEVICE_ATTR(cpu0_temperature,S_IRUGO,show_cpu0_temperature,NULL);
+static DEVICE_ATTR(cpu0_voltage,S_IRUGO,show_cpu0_voltage,NULL);
+static DEVICE_ATTR(cpu0_current,S_IRUGO,show_cpu0_current,NULL);
+static DEVICE_ATTR(cpu0_exhaust_fan_rpm,S_IRUGO,show_cpu0_exhaust_fan_rpm,NULL);
+static DEVICE_ATTR(cpu0_intake_fan_rpm,S_IRUGO,show_cpu0_intake_fan_rpm,NULL);
+
+static DEVICE_ATTR(cpu1_temperature,S_IRUGO,show_cpu1_temperature,NULL);
+static DEVICE_ATTR(cpu1_voltage,S_IRUGO,show_cpu1_voltage,NULL);
+static DEVICE_ATTR(cpu1_current,S_IRUGO,show_cpu1_current,NULL);
+static DEVICE_ATTR(cpu1_exhaust_fan_rpm,S_IRUGO,show_cpu1_exhaust_fan_rpm,NULL);
+static DEVICE_ATTR(cpu1_intake_fan_rpm,S_IRUGO,show_cpu1_intake_fan_rpm,NULL);
+
+static DEVICE_ATTR(backside_temperature,S_IRUGO,show_backside_temperature,NULL);
+static DEVICE_ATTR(backside_fan_pwm,S_IRUGO,show_backside_fan_pwm,NULL);
+
+static DEVICE_ATTR(drives_temperature,S_IRUGO,show_drives_temperature,NULL);
+static DEVICE_ATTR(drives_fan_rpm,S_IRUGO,show_drives_fan_rpm,NULL);
+
+static DEVICE_ATTR(dimms_temperature,S_IRUGO,show_dimms_temperature,NULL);
+
+/*
+ * CPUs fans control loop
+ */
+
+static int do_read_one_cpu_values(struct cpu_pid_state *state, s32 *temp, s32 *power)
+{
+	s32 ltemp, volts, amps;
+	int index, rc = 0;
+
+	/* Default (in case of error) */
+	*temp = state->cur_temp;
+	*power = state->cur_power;
+
+	if (cpu_pid_type == CPU_PID_TYPE_RACKMAC)
+		index = (state->index == 0) ?
+			CPU_A1_FAN_RPM_INDEX : CPU_B1_FAN_RPM_INDEX;
+	else
+		index = (state->index == 0) ?
+			CPUA_EXHAUST_FAN_RPM_INDEX : CPUB_EXHAUST_FAN_RPM_INDEX;
+
+	/* Read current fan status */
+	rc = get_rpm_fan(index, !RPM_PID_USE_ACTUAL_SPEED);
+	if (rc < 0) {
+		/* XXX What do we do now ? Nothing for now, keep old value, but
+		 * return error upstream
+		 */
+		DBG("  cpu %d, fan reading error !\n", state->index);
+	} else {
+		state->rpm = rc;
+		DBG("  cpu %d, exhaust RPM: %d\n", state->index, state->rpm);
+	}
+
+	/* Get some sensor readings and scale it */
+	ltemp = read_smon_adc(state, 1);
+	if (ltemp == -1) {
+		/* XXX What do we do now ? */
+		state->overtemp++;
+		if (rc == 0)
+			rc = -EIO;
+		DBG("  cpu %d, temp reading error !\n", state->index);
+	} else {
+		/* Fixup temperature according to diode calibration
+		 */
+		DBG("  cpu %d, temp raw: %04x, m_diode: %04x, b_diode: %04x\n",
+		    state->index,
+		    ltemp, state->mpu.mdiode, state->mpu.bdiode);
+		*temp = ((s32)ltemp * (s32)state->mpu.mdiode + ((s32)state->mpu.bdiode << 12)) >> 2;
+		state->last_temp = *temp;
+		DBG("  temp: %d.%03d\n", FIX32TOPRINT((*temp)));
+	}
+
+	/*
+	 * Read voltage & current and calculate power
+	 */
+	volts = read_smon_adc(state, 3);
+	amps = read_smon_adc(state, 4);
+
+	/* Scale voltage and current raw sensor values according to fixed scales
+	 * obtained in Darwin and calculate power from I and V
+	 */
+	volts *= ADC_CPU_VOLTAGE_SCALE;
+	amps *= ADC_CPU_CURRENT_SCALE;
+	*power = (((u64)volts) * ((u64)amps)) >> 16;
+	state->voltage = volts;
+	state->current_a = amps;
+	state->last_power = *power;
+
+	DBG("  cpu %d, current: %d.%03d, voltage: %d.%03d, power: %d.%03d W\n",
+	    state->index, FIX32TOPRINT(state->current_a),
+	    FIX32TOPRINT(state->voltage), FIX32TOPRINT(*power));
+
+	return 0;
+}
+
+static void do_cpu_pid(struct cpu_pid_state *state, s32 temp, s32 power)
+{
+	s32 power_target, integral, derivative, proportional, adj_in_target, sval;
+	s64 integ_p, deriv_p, prop_p, sum; 
+	int i;
+
+	/* Calculate power target value (could be done once for all)
+	 * and convert to a 16.16 fp number
+	 */
+	power_target = ((u32)(state->mpu.pmaxh - state->mpu.padjmax)) << 16;
+	DBG("  power target: %d.%03d, error: %d.%03d\n",
+	    FIX32TOPRINT(power_target), FIX32TOPRINT(power_target - power));
+
+	/* Store temperature and power in history array */
+	state->cur_temp = (state->cur_temp + 1) % CPU_TEMP_HISTORY_SIZE;
+	state->temp_history[state->cur_temp] = temp;
+	state->cur_power = (state->cur_power + 1) % state->count_power;
+	state->power_history[state->cur_power] = power;
+	state->error_history[state->cur_power] = power_target - power;
+	
+	/* If first loop, fill the history table */
+	if (state->first) {
+		for (i = 0; i < (state->count_power - 1); i++) {
+			state->cur_power = (state->cur_power + 1) % state->count_power;
+			state->power_history[state->cur_power] = power;
+			state->error_history[state->cur_power] = power_target - power;
+		}
+		for (i = 0; i < (CPU_TEMP_HISTORY_SIZE - 1); i++) {
+			state->cur_temp = (state->cur_temp + 1) % CPU_TEMP_HISTORY_SIZE;
+			state->temp_history[state->cur_temp] = temp;			
+		}
+		state->first = 0;
+	}
+
+	/* Calculate the integral term normally based on the "power" values */
+	sum = 0;
+	integral = 0;
+	for (i = 0; i < state->count_power; i++)
+		integral += state->error_history[i];
+	integral *= CPU_PID_INTERVAL;
+	DBG("  integral: %08x\n", integral);
+
+	/* Calculate the adjusted input (sense value).
+	 *   G_r is 12.20
+	 *   integ is 16.16
+	 *   so the result is 28.36
+	 *
+	 * input target is mpu.ttarget, input max is mpu.tmax
+	 */
+	integ_p = ((s64)state->mpu.pid_gr) * (s64)integral;
+	DBG("   integ_p: %d\n", (int)(integ_p >> 36));
+	sval = (state->mpu.tmax << 16) - ((integ_p >> 20) & 0xffffffff);
+	adj_in_target = (state->mpu.ttarget << 16);
+	if (adj_in_target > sval)
+		adj_in_target = sval;
+	DBG("   adj_in_target: %d.%03d, ttarget: %d\n", FIX32TOPRINT(adj_in_target),
+	    state->mpu.ttarget);
+
+	/* Calculate the derivative term */
+	derivative = state->temp_history[state->cur_temp] -
+		state->temp_history[(state->cur_temp + CPU_TEMP_HISTORY_SIZE - 1)
+				    % CPU_TEMP_HISTORY_SIZE];
+	derivative /= CPU_PID_INTERVAL;
+	deriv_p = ((s64)state->mpu.pid_gd) * (s64)derivative;
+	DBG("   deriv_p: %d\n", (int)(deriv_p >> 36));
+	sum += deriv_p;
+
+	/* Calculate the proportional term */
+	proportional = temp - adj_in_target;
+	prop_p = ((s64)state->mpu.pid_gp) * (s64)proportional;
+	DBG("   prop_p: %d\n", (int)(prop_p >> 36));
+	sum += prop_p;
+
+	/* Scale sum */
+	sum >>= 36;
+
+	DBG("   sum: %d\n", (int)sum);
+	state->rpm += (s32)sum;
+}
+
+static void do_monitor_cpu_combined(void)
+{
+	struct cpu_pid_state *state0 = &cpu_state[0];
+	struct cpu_pid_state *state1 = &cpu_state[1];
+	s32 temp0, power0, temp1, power1;
+	s32 temp_combi, power_combi;
+	int rc, intake, pump;
+
+	rc = do_read_one_cpu_values(state0, &temp0, &power0);
+	if (rc < 0) {
+		/* XXX What do we do now ? */
+	}
+	state1->overtemp = 0;
+	rc = do_read_one_cpu_values(state1, &temp1, &power1);
+	if (rc < 0) {
+		/* XXX What do we do now ? */
+	}
+	if (state1->overtemp)
+		state0->overtemp++;
+
+	temp_combi = max(temp0, temp1);
+	power_combi = max(power0, power1);
+
+	/* Check tmax, increment overtemp if we are there. At tmax+8, we go
+	 * full blown immediately and try to trigger a shutdown
+	 */
+	if (temp_combi >= ((state0->mpu.tmax + 8) << 16)) {
+		printk(KERN_WARNING "Warning ! Temperature way above maximum (%d) !\n",
+		       temp_combi >> 16);
+		state0->overtemp = CPU_MAX_OVERTEMP;
+	} else if (temp_combi > (state0->mpu.tmax << 16))
+		state0->overtemp++;
+	else
+		state0->overtemp = 0;
+	if (state0->overtemp >= CPU_MAX_OVERTEMP)
+		critical_state = 1;
+	if (state0->overtemp > 0) {
+		state0->rpm = state0->mpu.rmaxn_exhaust_fan;
+		state0->intake_rpm = intake = state0->mpu.rmaxn_intake_fan;
+		pump = state0->pump_min;
+		goto do_set_fans;
+	}
+
+	/* Do the PID */
+	do_cpu_pid(state0, temp_combi, power_combi);
+
+	/* Range check */
+	state0->rpm = max(state0->rpm, (int)state0->mpu.rminn_exhaust_fan);
+	state0->rpm = min(state0->rpm, (int)state0->mpu.rmaxn_exhaust_fan);
+
+	/* Calculate intake fan speed */
+	intake = (state0->rpm * CPU_INTAKE_SCALE) >> 16;
+	intake = max(intake, (int)state0->mpu.rminn_intake_fan);
+	intake = min(intake, (int)state0->mpu.rmaxn_intake_fan);
+	state0->intake_rpm = intake;
+
+	/* Calculate pump speed */
+	pump = (state0->rpm * state0->pump_max) /
+		state0->mpu.rmaxn_exhaust_fan;
+	pump = min(pump, state0->pump_max);
+	pump = max(pump, state0->pump_min);
+	
+ do_set_fans:
+	/* We copy values from state 0 to state 1 for /sysfs */
+	state1->rpm = state0->rpm;
+	state1->intake_rpm = state0->intake_rpm;
+
+	DBG("** CPU %d RPM: %d Ex, %d, Pump: %d, In, overtemp: %d\n",
+	    state1->index, (int)state1->rpm, intake, pump, state1->overtemp);
+
+	/* We should check for errors, shouldn't we ? But then, what
+	 * do we do once the error occurs ? For FCU notified fan
+	 * failures (-EFAULT) we probably want to notify userland
+	 * some way...
+	 */
+	set_rpm_fan(CPUA_INTAKE_FAN_RPM_INDEX, intake);
+	set_rpm_fan(CPUA_EXHAUST_FAN_RPM_INDEX, state0->rpm);
+	set_rpm_fan(CPUB_INTAKE_FAN_RPM_INDEX, intake);
+	set_rpm_fan(CPUB_EXHAUST_FAN_RPM_INDEX, state0->rpm);
+
+	if (fcu_fans[CPUA_PUMP_RPM_INDEX].id != FCU_FAN_ABSENT_ID)
+		set_rpm_fan(CPUA_PUMP_RPM_INDEX, pump);
+	if (fcu_fans[CPUB_PUMP_RPM_INDEX].id != FCU_FAN_ABSENT_ID)
+		set_rpm_fan(CPUB_PUMP_RPM_INDEX, pump);
+}
+
+static void do_monitor_cpu_split(struct cpu_pid_state *state)
+{
+	s32 temp, power;
+	int rc, intake;
+
+	/* Read current fan status */
+	rc = do_read_one_cpu_values(state, &temp, &power);
+	if (rc < 0) {
+		/* XXX What do we do now ? */
+	}
+
+	/* Check tmax, increment overtemp if we are there. At tmax+8, we go
+	 * full blown immediately and try to trigger a shutdown
+	 */
+	if (temp >= ((state->mpu.tmax + 8) << 16)) {
+		printk(KERN_WARNING "Warning ! CPU %d temperature way above maximum"
+		       " (%d) !\n",
+		       state->index, temp >> 16);
+		state->overtemp = CPU_MAX_OVERTEMP;
+	} else if (temp > (state->mpu.tmax << 16))
+		state->overtemp++;
+	else
+		state->overtemp = 0;
+	if (state->overtemp >= CPU_MAX_OVERTEMP)
+		critical_state = 1;
+	if (state->overtemp > 0) {
+		state->rpm = state->mpu.rmaxn_exhaust_fan;
+		state->intake_rpm = intake = state->mpu.rmaxn_intake_fan;
+		goto do_set_fans;
+	}
+
+	/* Do the PID */
+	do_cpu_pid(state, temp, power);
+
+	/* Range check */
+	state->rpm = max(state->rpm, (int)state->mpu.rminn_exhaust_fan);
+	state->rpm = min(state->rpm, (int)state->mpu.rmaxn_exhaust_fan);
+
+	/* Calculate intake fan */
+	intake = (state->rpm * CPU_INTAKE_SCALE) >> 16;
+	intake = max(intake, (int)state->mpu.rminn_intake_fan);
+	intake = min(intake, (int)state->mpu.rmaxn_intake_fan);
+	state->intake_rpm = intake;
+
+ do_set_fans:
+	DBG("** CPU %d RPM: %d Ex, %d In, overtemp: %d\n",
+	    state->index, (int)state->rpm, intake, state->overtemp);
+
+	/* We should check for errors, shouldn't we ? But then, what
+	 * do we do once the error occurs ? For FCU notified fan
+	 * failures (-EFAULT) we probably want to notify userland
+	 * some way...
+	 */
+	if (state->index == 0) {
+		set_rpm_fan(CPUA_INTAKE_FAN_RPM_INDEX, intake);
+		set_rpm_fan(CPUA_EXHAUST_FAN_RPM_INDEX, state->rpm);
+	} else {
+		set_rpm_fan(CPUB_INTAKE_FAN_RPM_INDEX, intake);
+		set_rpm_fan(CPUB_EXHAUST_FAN_RPM_INDEX, state->rpm);
+	}
+}
+
+static void do_monitor_cpu_rack(struct cpu_pid_state *state)
+{
+	s32 temp, power, fan_min;
+	int rc;
+
+	/* Read current fan status */
+	rc = do_read_one_cpu_values(state, &temp, &power);
+	if (rc < 0) {
+		/* XXX What do we do now ? */
+	}
+
+	/* Check tmax, increment overtemp if we are there. At tmax+8, we go
+	 * full blown immediately and try to trigger a shutdown
+	 */
+	if (temp >= ((state->mpu.tmax + 8) << 16)) {
+		printk(KERN_WARNING "Warning ! CPU %d temperature way above maximum"
+		       " (%d) !\n",
+		       state->index, temp >> 16);
+		state->overtemp = CPU_MAX_OVERTEMP;
+	} else if (temp > (state->mpu.tmax << 16))
+		state->overtemp++;
+	else
+		state->overtemp = 0;
+	if (state->overtemp >= CPU_MAX_OVERTEMP)
+		critical_state = 1;
+	if (state->overtemp > 0) {
+		state->rpm = state->intake_rpm = state->mpu.rmaxn_intake_fan;
+		goto do_set_fans;
+	}
+
+	/* Do the PID */
+	do_cpu_pid(state, temp, power);
+
+	/* Check clamp from dimms */
+	fan_min = dimm_output_clamp;
+	fan_min = max(fan_min, (int)state->mpu.rminn_intake_fan);
+
+	state->rpm = max(state->rpm, (int)fan_min);
+	state->rpm = min(state->rpm, (int)state->mpu.rmaxn_intake_fan);
+	state->intake_rpm = state->rpm;
+
+ do_set_fans:
+	DBG("** CPU %d RPM: %d overtemp: %d\n",
+	    state->index, (int)state->rpm, state->overtemp);
+
+	/* We should check for errors, shouldn't we ? But then, what
+	 * do we do once the error occurs ? For FCU notified fan
+	 * failures (-EFAULT) we probably want to notify userland
+	 * some way...
+	 */
+	if (state->index == 0) {
+		set_rpm_fan(CPU_A1_FAN_RPM_INDEX, state->rpm);
+		set_rpm_fan(CPU_A2_FAN_RPM_INDEX, state->rpm);
+		set_rpm_fan(CPU_A3_FAN_RPM_INDEX, state->rpm);
+	} else {
+		set_rpm_fan(CPU_B1_FAN_RPM_INDEX, state->rpm);
+		set_rpm_fan(CPU_B2_FAN_RPM_INDEX, state->rpm);
+		set_rpm_fan(CPU_B3_FAN_RPM_INDEX, state->rpm);
+	}
+}
+
+/*
+ * Initialize the state structure for one CPU control loop
+ */
+static int init_cpu_state(struct cpu_pid_state *state, int index)
+{
+	state->index = index;
+	state->first = 1;
+	state->rpm = (cpu_pid_type == CPU_PID_TYPE_RACKMAC) ? 4000 : 1000;
+	sta