Merge tag 'iio-for-5.1b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Second set of new device support, features and cleanup for IIO in the 5.1 cycle.

There are a few late breaking fixes in here that weren't worth trying to
rush into 5.0 as they have been with us for quite a while.

New device support
* ad7476
  - add support for TI ADS786X parts that are compatible with this Analog
    Devices driver. Good to see some simple devices are so similar.
* Ingenic jz47xx SoC ADCs
  - new driver and bindings
* Plantower PMS7003 partical sensor
  - new driver and bindings including vendor prefix.
* TI DAC7612
  - new driver and bindings for this dual DAC.

New features
* ad7768-1
  - Sampling frequency control
* bmi160
  - Data ready trigger support, including open-drain dt binding.

Cleanup / minor fixes.
* Analog Device DACs
  - Fix some inconsistent licenses.  These are only ones where there were
    two different license marked in the same file, and hence were previously
    unclear.
* ads124s08
  - Spelling fix.
* adxl345
  - Parameter alignement tidy up.
* bmi160
  - SPDX
  - correct a note on the types of supported interrupts which was too strict.
  - use iio_pollfunc_store_time to grab an earlier timestamp.
  - use if (ret) instead of if (ret < 0) to be consistent whilst simplifying
    some handling where ret was effectively getting written to 0 even though
    it was always already 0.
* exynos_adc
  - Fix a null pointer dereference on unbind.
  - Fix number of channels on Exynos4x12 devices to be 4 rather than 8.
* lpc32xx-adc
  - Move DT bindings doc out of staging. Oops, I missed this one when
    moving the driver.
  - SPDX.
* npcm-adc
  - drop documentation of reset node as going to be done differently.
    It's a new driver this cycle so no need to support the previous
    binding going forwards.
* sps30
  - Fix an issue with a loop timeout test that meant it would never identify
    a timeout.
  - Mark deliberate switch fall throughs.

* tag 'iio-for-5.1b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (26 commits)
  iio: adc: exynos-adc: Use proper number of channels for Exynos4x12
  dt-binding: iio: remove rst node from NPCM ADC document
  dt-bindings: iio: chemical: pms7003: add device tree support
  dt-bindings: add Plantower to the vendor prefixes
  iio: chemical: add support for Plantower PMS7003 sensor
  iio:chemical:sps30 Supress some switch fallthrough warnings.
  iio:adc:lpc32xx use SPDX-License-Identifier
  dt-bindings: iio: adc: move lpc32xx-adc out of staging
  iio: adc: ads124s08: fix spelling mistake "converions" -> "conversions"
  iio: adc: exynos-adc: Fix NULL pointer exception on unbind
  iio: chemical: sps30: fix a loop timeout test
  iio:accel:adxl345: Change alignment to match paranthesis
  iio:dac:dac7612: device tree bindings
  iio:dac:ti-dac7612: Add driver for Texas Instruments DAC7612
  iio: adc: ad7476: Add support for TI ADS786X ADCs
  iio: adc: ad7768-1: Add support for setting the sampling frequency
  drivers: iio: dac: Fix wrong license for ADI drivers
  IIO: add Ingenic JZ47xx ADC driver.
  dt-bindings: iio/adc: Add bindings for Ingenic JZ47xx SoCs ADC.
  dt-bindings: iio/adc: Add docs for Ingenic JZ47xx SoCs ADC.
  ...

25 files changed, 1480 insertions, 71 deletions

diff --git a/drivers/iio/accel/adxl345_core.c b/drivers/iio/accel/adxl345_core.c
index 780f87f72338..f03ed00685ea 100644
--- a/drivers/iio/accel/adxl345_core.c
+++ b/drivers/iio/accel/adxl345_core.c
@@ -150,8 +150,8 @@ static int adxl345_read_raw(struct iio_dev *indio_dev,
 }
 
 static int adxl345_write_raw(struct iio_dev *indio_dev,
-			    struct iio_chan_spec const *chan,
-			    int val, int val2, long mask)
+			     struct iio_chan_spec const *chan,
+			     int val, int val2, long mask)
 {
 	struct adxl345_data *data = iio_priv(indio_dev);
 	s64 n;
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 46ed6fa7e3f3..5debc67df70a 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -57,14 +57,17 @@ config AD7298
 	  module will be called ad7298.
 
 config AD7476
-	tristate "Analog Devices AD7476 and similar 1-channel ADCs driver"
+	tristate "Analog Devices AD7476 1-channel ADCs driver and other similar devices from AD an TI"
 	depends on SPI
 	select IIO_BUFFER
 	select IIO_TRIGGERED_BUFFER
 	help
-	  Say yes here to build support for Analog Devices AD7273, AD7274, AD7276,
-	  AD7277, AD7278, AD7475, AD7476, AD7477, AD7478, AD7466, AD7467, AD7468,
-	  AD7495, AD7910, AD7920, AD7920 SPI analog to digital converters (ADC).
+	  Say yes here to build support for the following SPI analog to
+	  digital converters (ADCs):
+	  Analog Devices: AD7273, AD7274, AD7276, AD7277, AD7278, AD7475,
+	  AD7476, AD7477, AD7478, AD7466, AD7467, AD7468, AD7495, AD7910,
+	  AD7920.
+	  Texas Instruments: ADS7866, ADS7867, ADS7868.
 
 	  To compile this driver as a module, choose M here: the
 	  module will be called ad7476.
@@ -407,6 +410,15 @@ config INA2XX_ADC
 	  Say yes here to build support for TI INA2xx family of Power Monitors.
 	  This driver is mutually exclusive with the HWMON version.
 
+config INGENIC_ADC
+	tristate "Ingenic JZ47xx SoCs ADC driver"
+	depends on MIPS || COMPILE_TEST
+	help
+	  Say yes here to build support for the Ingenic JZ47xx SoCs ADC unit.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called ingenic_adc.
+
 config IMX7D_ADC
 	tristate "Freescale IMX7D ADC driver"
 	depends on ARCH_MXC || COMPILE_TEST
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 79d6511f0af3..d50eb47da484 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -40,6 +40,7 @@ obj-$(CONFIG_HI8435) += hi8435.o
 obj-$(CONFIG_HX711) += hx711.o
 obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
 obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o
+obj-$(CONFIG_INGENIC_ADC) += ingenic-adc.o
 obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
 obj-$(CONFIG_LPC18XX_ADC) += lpc18xx_adc.o
 obj-$(CONFIG_LPC32XX_ADC) += lpc32xx_adc.o
diff --git a/drivers/iio/adc/ad7476.c b/drivers/iio/adc/ad7476.c
index 0549686b9ef8..76747488044b 100644
--- a/drivers/iio/adc/ad7476.c
+++ b/drivers/iio/adc/ad7476.c
@@ -59,6 +59,9 @@ enum ad7476_supported_device_ids {
 	ID_ADC081S,
 	ID_ADC101S,
 	ID_ADC121S,
+	ID_ADS7866,
+	ID_ADS7867,
+	ID_ADS7868,
 };
 
 static irqreturn_t ad7476_trigger_handler(int irq, void  *p)
@@ -157,6 +160,8 @@ static int ad7476_read_raw(struct iio_dev *indio_dev,
 #define AD7940_CHAN(bits) _AD7476_CHAN((bits), 15 - (bits), \
 		BIT(IIO_CHAN_INFO_RAW))
 #define AD7091R_CHAN(bits) _AD7476_CHAN((bits), 16 - (bits), 0)
+#define ADS786X_CHAN(bits) _AD7476_CHAN((bits), 12 - (bits), \
+		BIT(IIO_CHAN_INFO_RAW))
 
 static const struct ad7476_chip_info ad7476_chip_info_tbl[] = {
 	[ID_AD7091R] = {
@@ -209,6 +214,18 @@ static const struct ad7476_chip_info ad7476_chip_info_tbl[] = {
 		.channel[0] = ADC081S_CHAN(12),
 		.channel[1] = IIO_CHAN_SOFT_TIMESTAMP(1),
 	},
+	[ID_ADS7866] = {
+		.channel[0] = ADS786X_CHAN(12),
+		.channel[1] = IIO_CHAN_SOFT_TIMESTAMP(1),
+	},
+	[ID_ADS7867] = {
+		.channel[0] = ADS786X_CHAN(10),
+		.channel[1] = IIO_CHAN_SOFT_TIMESTAMP(1),
+	},
+	[ID_ADS7868] = {
+		.channel[0] = ADS786X_CHAN(8),
+		.channel[1] = IIO_CHAN_SOFT_TIMESTAMP(1),
+	},
 };
 
 static const struct iio_info ad7476_info = {
@@ -314,6 +331,9 @@ static const struct spi_device_id ad7476_id[] = {
 	{"adc081s", ID_ADC081S},
 	{"adc101s", ID_ADC101S},
 	{"adc121s", ID_ADC121S},
+	{"ads7866", ID_ADS7866},
+	{"ads7867", ID_ADS7867},
+	{"ads7868", ID_ADS7868},
 	{}
 };
 MODULE_DEVICE_TABLE(spi, ad7476_id);
diff --git a/drivers/iio/adc/ad7768-1.c b/drivers/iio/adc/ad7768-1.c
index 78449e90b2f5..0d132708c429 100644
--- a/drivers/iio/adc/ad7768-1.c
+++ b/drivers/iio/adc/ad7768-1.c
@@ -9,6 +9,7 @@
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/err.h>
+#include <linux/gpio/consumer.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/regulator/consumer.h>
@@ -59,6 +60,18 @@
 #define AD7768_REG_DIG_DIAG_STATUS	0x30
 #define AD7768_REG_MCLK_COUNTER		0x31
 
+/* AD7768_REG_POWER_CLOCK */
+#define AD7768_PWR_MCLK_DIV_MSK		GENMASK(5, 4)
+#define AD7768_PWR_MCLK_DIV(x)		FIELD_PREP(AD7768_PWR_MCLK_DIV_MSK, x)
+#define AD7768_PWR_PWRMODE_MSK		GENMASK(1, 0)
+#define AD7768_PWR_PWRMODE(x)		FIELD_PREP(AD7768_PWR_PWRMODE_MSK, x)
+
+/* AD7768_REG_DIGITAL_FILTER */
+#define AD7768_DIG_FIL_FIL_MSK		GENMASK(6, 4)
+#define AD7768_DIG_FIL_FIL(x)		FIELD_PREP(AD7768_DIG_FIL_FIL_MSK, x)
+#define AD7768_DIG_FIL_DEC_MSK		GENMASK(2, 0)
+#define AD7768_DIG_FIL_DEC_RATE(x)	FIELD_PREP(AD7768_DIG_FIL_DEC_MSK, x)
+
 /* AD7768_REG_CONVERSION */
 #define AD7768_CONV_MODE_MSK		GENMASK(2, 0)
 #define AD7768_CONV_MODE(x)		FIELD_PREP(AD7768_CONV_MODE_MSK, x)
@@ -80,11 +93,51 @@ enum ad7768_pwrmode {
 	AD7768_FAST_MODE = 3
 };
 
+enum ad7768_mclk_div {
+	AD7768_MCLK_DIV_16,
+	AD7768_MCLK_DIV_8,
+	AD7768_MCLK_DIV_4,
+	AD7768_MCLK_DIV_2
+};
+
+enum ad7768_dec_rate {
+	AD7768_DEC_RATE_32 = 0,
+	AD7768_DEC_RATE_64 = 1,
+	AD7768_DEC_RATE_128 = 2,
+	AD7768_DEC_RATE_256 = 3,
+	AD7768_DEC_RATE_512 = 4,
+	AD7768_DEC_RATE_1024 = 5,
+	AD7768_DEC_RATE_8 = 9,
+	AD7768_DEC_RATE_16 = 10
+};
+
+struct ad7768_clk_configuration {
+	enum ad7768_mclk_div mclk_div;
+	enum ad7768_dec_rate dec_rate;
+	unsigned int clk_div;
+	enum ad7768_pwrmode pwrmode;
+};
+
+static const struct ad7768_clk_configuration ad7768_clk_config[] = {
+	{ AD7768_MCLK_DIV_2, AD7768_DEC_RATE_8, 16,  AD7768_FAST_MODE },
+	{ AD7768_MCLK_DIV_2, AD7768_DEC_RATE_16, 32,  AD7768_FAST_MODE },
+	{ AD7768_MCLK_DIV_2, AD7768_DEC_RATE_32, 64, AD7768_FAST_MODE },
+	{ AD7768_MCLK_DIV_2, AD7768_DEC_RATE_64, 128, AD7768_FAST_MODE },
+	{ AD7768_MCLK_DIV_2, AD7768_DEC_RATE_128, 256, AD7768_FAST_MODE },
+	{ AD7768_MCLK_DIV_4, AD7768_DEC_RATE_128, 512, AD7768_MED_MODE },
+	{ AD7768_MCLK_DIV_4, AD7768_DEC_RATE_256, 1024, AD7768_MED_MODE },
+	{ AD7768_MCLK_DIV_4, AD7768_DEC_RATE_512, 2048, AD7768_MED_MODE },
+	{ AD7768_MCLK_DIV_4, AD7768_DEC_RATE_1024, 4096, AD7768_MED_MODE },
+	{ AD7768_MCLK_DIV_8, AD7768_DEC_RATE_1024, 8192, AD7768_MED_MODE },
+	{ AD7768_MCLK_DIV_16, AD7768_DEC_RATE_1024, 16384, AD7768_ECO_MODE },
+};
+
 static const struct iio_chan_spec ad7768_channels[] = {
 	{
 		.type = IIO_VOLTAGE,
 		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.indexed = 1,
 		.channel = 0,
 		.scan_index = 0,
@@ -102,8 +155,12 @@ struct ad7768_state {
 	struct spi_device *spi;
 	struct regulator *vref;
 	struct mutex lock;
+	struct clk *mclk;
+	unsigned int mclk_freq;
+	unsigned int samp_freq;
 	struct completion completion;
 	struct iio_trigger *trig;
+	struct gpio_desc *gpio_sync_in;
 	/*
 	 * DMA (thus cache coherency maintenance) requires the
 	 * transfer buffers to live in their own cache lines.
@@ -210,6 +267,90 @@ err_unlock:
 	return ret;
 }
 
+static int ad7768_set_dig_fil(struct ad7768_state *st,
+			      enum ad7768_dec_rate dec_rate)
+{
+	unsigned int mode;
+	int ret;
+
+	if (dec_rate == AD7768_DEC_RATE_8 || dec_rate == AD7768_DEC_RATE_16)
+		mode = AD7768_DIG_FIL_FIL(dec_rate);
+	else
+		mode = AD7768_DIG_FIL_DEC_RATE(dec_rate);
+
+	ret = ad7768_spi_reg_write(st, AD7768_REG_DIGITAL_FILTER, mode);
+	if (ret < 0)
+		return ret;
+
+	/* A sync-in pulse is required every time the filter dec rate changes */
+	gpiod_set_value(st->gpio_sync_in, 1);
+	gpiod_set_value(st->gpio_sync_in, 0);
+
+	return 0;
+}
+
+static int ad7768_set_freq(struct ad7768_state *st,
+			   unsigned int freq)
+{
+	unsigned int diff_new, diff_old, pwr_mode, i, idx;
+	int res, ret;
+
+	diff_old = U32_MAX;
+	idx = 0;
+
+	res = DIV_ROUND_CLOSEST(st->mclk_freq, freq);
+
+	/* Find the closest match for the desired sampling frequency */
+	for (i = 0; i < ARRAY_SIZE(ad7768_clk_config); i++) {
+		diff_new = abs(res - ad7768_clk_config[i].clk_div);
+		if (diff_new < diff_old) {
+			diff_old = diff_new;
+			idx = i;
+		}
+	}
+
+	/*
+	 * Set both the mclk_div and pwrmode with a single write to the
+	 * POWER_CLOCK register
+	 */
+	pwr_mode = AD7768_PWR_MCLK_DIV(ad7768_clk_config[idx].mclk_div) |
+		   AD7768_PWR_PWRMODE(ad7768_clk_config[idx].pwrmode);
+	ret = ad7768_spi_reg_write(st, AD7768_REG_POWER_CLOCK, pwr_mode);
+	if (ret < 0)
+		return ret;
+
+	ret =  ad7768_set_dig_fil(st, ad7768_clk_config[idx].dec_rate);
+	if (ret < 0)
+		return ret;
+
+	st->samp_freq = DIV_ROUND_CLOSEST(st->mclk_freq,
+					  ad7768_clk_config[idx].clk_div);
+
+	return 0;
+}
+
+static ssize_t ad7768_sampling_freq_avail(struct device *dev,
+					  struct device_attribute *attr,
+					  char *buf)
+{
+	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+	struct ad7768_state *st = iio_priv(indio_dev);
+	unsigned int freq;
+	int i, len = 0;
+
+	for (i = 0; i < ARRAY_SIZE(ad7768_clk_config); i++) {
+		freq = DIV_ROUND_CLOSEST(st->mclk_freq,
+					 ad7768_clk_config[i].clk_div);
+		len += scnprintf(buf + len, PAGE_SIZE - len, "%d ", freq);
+	}
+
+	buf[len - 1] = '\n';
+
+	return len;
+}
+
+static IIO_DEV_ATTR_SAMP_FREQ_AVAIL(ad7768_sampling_freq_avail);
+
 static int ad7768_read_raw(struct iio_dev *indio_dev,
 			   struct iio_chan_spec const *chan,
 			   int *val, int *val2, long info)
@@ -242,13 +383,43 @@ static int ad7768_read_raw(struct iio_dev *indio_dev,
 		*val2 = chan->scan_type.realbits;
 
 		return IIO_VAL_FRACTIONAL_LOG2;
+
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*val = st->samp_freq;
+
+		return IIO_VAL_INT;
 	}
 
 	return -EINVAL;
 }
 
+static int ad7768_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int val, int val2, long info)
+{
+	struct ad7768_state *st = iio_priv(indio_dev);
+
+	switch (info) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		return ad7768_set_freq(st, val);
+	default:
+		return -EINVAL;
+	}
+}
+
+static struct attribute *ad7768_attributes[] = {
+	&iio_dev_attr_sampling_frequency_available.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group ad7768_group = {
+	.attrs = ad7768_attributes,
+};
+
 static const struct iio_info ad7768_info = {
+	.attrs = &ad7768_group,
 	.read_raw = &ad7768_read_raw,
+	.write_raw = &ad7768_write_raw,
 	.debugfs_reg_access = &ad7768_reg_access,
 };
 
@@ -270,9 +441,13 @@ static int ad7768_setup(struct ad7768_state *st)
 	if (ret)
 		return ret;
 
-	/* Set power mode to fast */
-	return ad7768_spi_reg_write(st, AD7768_REG_POWER_CLOCK,
-				    AD7768_FAST_MODE);
+	st->gpio_sync_in = devm_gpiod_get(&st->spi->dev, "adi,sync-in",
+					  GPIOD_OUT_LOW);
+	if (IS_ERR(st->gpio_sync_in))
+		return PTR_ERR(st->gpio_sync_in);
+
+	/* Set the default sampling frequency to 32000 kSPS */
+	return ad7768_set_freq(st, 32000);
 }
 
 static irqreturn_t ad7768_trigger_handler(int irq, void *p)
@@ -356,6 +531,13 @@ static void ad7768_regulator_disable(void *data)
 	regulator_disable(st->vref);
 }
 
+static void ad7768_clk_disable(void *data)
+{
+	struct ad7768_state *st = data;
+
+	clk_disable_unprepare(st->mclk);
+}
+
 static int ad7768_probe(struct spi_device *spi)
 {
 	struct ad7768_state *st;
@@ -383,6 +565,20 @@ static int ad7768_probe(struct spi_device *spi)
 	if (ret)
 		return ret;
 
+	st->mclk = devm_clk_get(&spi->dev, "mclk");
+	if (IS_ERR(st->mclk))
+		return PTR_ERR(st->mclk);
+
+	ret = clk_prepare_enable(st->mclk);
+	if (ret < 0)
+		return ret;
+
+	ret = devm_add_action_or_reset(&spi->dev, ad7768_clk_disable, st);
+	if (ret)
+		return ret;
+
+	st->mclk_freq = clk_get_rate(st->mclk);
+
 	spi_set_drvdata(spi, indio_dev);
 	mutex_init(&st->lock);
 
diff --git a/drivers/iio/adc/exynos_adc.c b/drivers/iio/adc/exynos_adc.c
index fa2d2b5767f3..1ca2c4d39f87 100644
--- a/drivers/iio/adc/exynos_adc.c
+++ b/drivers/iio/adc/exynos_adc.c
@@ -115,6 +115,7 @@
 #define MAX_ADC_V2_CHANNELS		10
 #define MAX_ADC_V1_CHANNELS		8
 #define MAX_EXYNOS3250_ADC_CHANNELS	2
+#define MAX_EXYNOS4212_ADC_CHANNELS	4
 #define MAX_S5PV210_ADC_CHANNELS	10
 
 /* Bit definitions common for ADC_V1 and ADC_V2 */
@@ -271,6 +272,19 @@ static void exynos_adc_v1_start_conv(struct exynos_adc *info,
 	writel(con1 | ADC_CON_EN_START, ADC_V1_CON(info->regs));
 }
 
+/* Exynos4212 and 4412 is like ADCv1 but with four channels only */
+static const struct exynos_adc_data exynos4212_adc_data = {
+	.num_channels	= MAX_EXYNOS4212_ADC_CHANNELS,
+	.mask		= ADC_DATX_MASK,	/* 12 bit ADC resolution */
+	.needs_adc_phy	= true,
+	.phy_offset	= EXYNOS_ADCV1_PHY_OFFSET,
+
+	.init_hw	= exynos_adc_v1_init_hw,
+	.exit_hw	= exynos_adc_v1_exit_hw,
+	.clear_irq	= exynos_adc_v1_clear_irq,
+	.start_conv	= exynos_adc_v1_start_conv,
+};
+
 static const struct exynos_adc_data exynos_adc_v1_data = {
 	.num_channels	= MAX_ADC_V1_CHANNELS,
 	.mask		= ADC_DATX_MASK,	/* 12 bit ADC resolution */
@@ -493,6 +507,9 @@ static const struct of_device_id exynos_adc_match[] = {
 		.compatible = "samsung,s5pv210-adc",
 		.data = &exynos_adc_s5pv210_data,
 	}, {
+		.compatible = "samsung,exynos4212-adc",
+		.data = &exynos4212_adc_data,
+	}, {
 		.compatible = "samsung,exynos-adc-v1",
 		.data = &exynos_adc_v1_data,
 	}, {
@@ -929,7 +946,7 @@ static int exynos_adc_remove(struct platform_device *pdev)
 	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
 	struct exynos_adc *info = iio_priv(indio_dev);
 
-	if (IS_REACHABLE(CONFIG_INPUT)) {
+	if (IS_REACHABLE(CONFIG_INPUT) && info->input) {
 		free_irq(info->tsirq, info);
 		input_unregister_device(info->input);
 	}
diff --git a/drivers/iio/adc/ingenic-adc.c b/drivers/iio/adc/ingenic-adc.c
new file mode 100644
index 000000000000..6ee1673deb0d
--- /dev/null
+++ b/drivers/iio/adc/ingenic-adc.c
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ADC driver for the Ingenic JZ47xx SoCs
+ * Copyright (c) 2019 Artur Rojek <contact@artur-rojek.eu>
+ *
+ * based on drivers/mfd/jz4740-adc.c
+ */
+
+#include <dt-bindings/iio/adc/ingenic,adc.h>
+#include <linux/clk.h>
+#include <linux/iio/iio.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+
+#define JZ_ADC_REG_ENABLE		0x00
+#define JZ_ADC_REG_CFG			0x04
+#define JZ_ADC_REG_CTRL			0x08
+#define JZ_ADC_REG_STATUS		0x0c
+#define JZ_ADC_REG_ADTCH		0x18
+#define JZ_ADC_REG_ADBDAT		0x1c
+#define JZ_ADC_REG_ADSDAT		0x20
+
+#define JZ_ADC_REG_CFG_BAT_MD		BIT(4)
+
+#define JZ_ADC_AUX_VREF				3300
+#define JZ_ADC_AUX_VREF_BITS			12
+#define JZ_ADC_BATTERY_LOW_VREF			2500
+#define JZ_ADC_BATTERY_LOW_VREF_BITS		12
+#define JZ4725B_ADC_BATTERY_HIGH_VREF		7500
+#define JZ4725B_ADC_BATTERY_HIGH_VREF_BITS	10
+#define JZ4740_ADC_BATTERY_HIGH_VREF		(7500 * 0.986)
+#define JZ4740_ADC_BATTERY_HIGH_VREF_BITS	12
+
+struct ingenic_adc_soc_data {
+	unsigned int battery_high_vref;
+	unsigned int battery_high_vref_bits;
+	const int *battery_raw_avail;
+	size_t battery_raw_avail_size;
+	const int *battery_scale_avail;
+	size_t battery_scale_avail_size;
+};
+
+struct ingenic_adc {
+	void __iomem *base;
+	struct clk *clk;
+	struct mutex lock;
+	const struct ingenic_adc_soc_data *soc_data;
+	bool low_vref_mode;
+};
+
+static void ingenic_adc_set_config(struct ingenic_adc *adc,
+				   uint32_t mask,
+				   uint32_t val)
+{
+	uint32_t cfg;
+
+	clk_enable(adc->clk);
+	mutex_lock(&adc->lock);
+
+	cfg = readl(adc->base + JZ_ADC_REG_CFG) & ~mask;
+	cfg |= val;
+	writel(cfg, adc->base + JZ_ADC_REG_CFG);
+
+	mutex_unlock(&adc->lock);
+	clk_disable(adc->clk);
+}
+
+static void ingenic_adc_enable(struct ingenic_adc *adc,
+			       int engine,
+			       bool enabled)
+{
+	u8 val;
+
+	mutex_lock(&adc->lock);
+	val = readb(adc->base + JZ_ADC_REG_ENABLE);
+
+	if (enabled)
+		val |= BIT(engine);
+	else
+		val &= ~BIT(engine);
+
+	writeb(val, adc->base + JZ_ADC_REG_ENABLE);
+	mutex_unlock(&adc->lock);
+}
+
+static int ingenic_adc_capture(struct ingenic_adc *adc,
+			       int engine)
+{
+	u8 val;
+	int ret;
+
+	ingenic_adc_enable(adc, engine, true);
+	ret = readb_poll_timeout(adc->base + JZ_ADC_REG_ENABLE, val,
+				 !(val & BIT(engine)), 250, 1000);
+	if (ret)
+		ingenic_adc_enable(adc, engine, false);
+
+	return ret;
+}
+
+static int ingenic_adc_write_raw(struct iio_dev *iio_dev,
+				 struct iio_chan_spec const *chan,
+				 int val,
+				 int val2,
+				 long m)
+{
+	struct ingenic_adc *adc = iio_priv(iio_dev);
+
+	switch (m) {
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->channel) {
+		case INGENIC_ADC_BATTERY:
+			if (val > JZ_ADC_BATTERY_LOW_VREF) {
+				ingenic_adc_set_config(adc,
+						       JZ_ADC_REG_CFG_BAT_MD,
+						       0);
+				adc->low_vref_mode = false;
+			} else {
+				ingenic_adc_set_config(adc,
+						       JZ_ADC_REG_CFG_BAT_MD,
+						       JZ_ADC_REG_CFG_BAT_MD);
+				adc->low_vref_mode = true;
+			}
+			return 0;
+		default:
+			return -EINVAL;
+		}
+	default:
+		return -EINVAL;
+	}
+}
+
+static const int jz4725b_adc_battery_raw_avail[] = {
+	0, 1, (1 << JZ_ADC_BATTERY_LOW_VREF_BITS) - 1,
+};
+
+static const int jz4725b_adc_battery_scale_avail[] = {
+	JZ4725B_ADC_BATTERY_HIGH_VREF, JZ4725B_ADC_BATTERY_HIGH_VREF_BITS,
+	JZ_ADC_BATTERY_LOW_VREF, JZ_ADC_BATTERY_LOW_VREF_BITS,
+};
+
+static const int jz4740_adc_battery_raw_avail[] = {
+	0, 1, (1 << JZ_ADC_BATTERY_LOW_VREF_BITS) - 1,
+};
+
+static const int jz4740_adc_battery_scale_avail[] = {
+	JZ4740_ADC_BATTERY_HIGH_VREF, JZ4740_ADC_BATTERY_HIGH_VREF_BITS,
+	JZ_ADC_BATTERY_LOW_VREF, JZ_ADC_BATTERY_LOW_VREF_BITS,
+};
+
+static const struct ingenic_adc_soc_data jz4725b_adc_soc_data = {
+	.battery_high_vref = JZ4725B_ADC_BATTERY_HIGH_VREF,
+	.battery_high_vref_bits = JZ4725B_ADC_BATTERY_HIGH_VREF_BITS,
+	.battery_raw_avail = jz4725b_adc_battery_raw_avail,
+	.battery_raw_avail_size = ARRAY_SIZE(jz4725b_adc_battery_raw_avail),
+	.battery_scale_avail = jz4725b_adc_battery_scale_avail,
+	.battery_scale_avail_size = ARRAY_SIZE(jz4725b_adc_battery_scale_avail),
+};
+
+static const struct ingenic_adc_soc_data jz4740_adc_soc_data = {
+	.battery_high_vref = JZ4740_ADC_BATTERY_HIGH_VREF,
+	.battery_high_vref_bits = JZ4740_ADC_BATTERY_HIGH_VREF_BITS,
+	.battery_raw_avail = jz4740_adc_battery_raw_avail,
+	.battery_raw_avail_size = ARRAY_SIZE(jz4740_adc_battery_raw_avail),
+	.battery_scale_avail = jz4740_adc_battery_scale_avail,
+	.battery_scale_avail_size = ARRAY_SIZE(jz4740_adc_battery_scale_avail),
+};
+
+static int ingenic_adc_read_avail(struct iio_dev *iio_dev,
+				  struct iio_chan_spec const *chan,
+				  const int **vals,
+				  int *type,
+				  int *length,
+				  long m)
+{
+	struct ingenic_adc *adc = iio_priv(iio_dev);
+
+	switch (m) {
+	case IIO_CHAN_INFO_RAW:
+		*type = IIO_VAL_INT;
+		*length = adc->soc_data->battery_raw_avail_size;
+		*vals = adc->soc_data->battery_raw_avail;
+		return IIO_AVAIL_RANGE;
+	case IIO_CHAN_INFO_SCALE:
+		*type = IIO_VAL_FRACTIONAL_LOG2;
+		*length = adc->soc_data->battery_scale_avail_size;
+		*vals = adc->soc_data->battery_scale_avail;
+		return IIO_AVAIL_LIST;
+	default:
+		return -EINVAL;
+	};
+}
+
+static int ingenic_adc_read_raw(struct iio_dev *iio_dev,
+				struct iio_chan_spec const *chan,
+				int *val,
+				int *val2,
+				long m)
+{
+	struct ingenic_adc *adc = iio_priv(iio_dev);
+	int ret;
+
+	switch (m) {
+	case IIO_CHAN_INFO_RAW:
+		clk_enable(adc->clk);
+		ret = ingenic_adc_capture(adc, chan->channel);
+		if (ret) {
+			clk_disable(adc->clk);
+			return ret;
+		}
+
+		switch (chan->channel) {
+		case INGENIC_ADC_AUX:
+			*val = readw(adc->base + JZ_ADC_REG_ADSDAT);
+			break;
+		case INGENIC_ADC_BATTERY:
+			*val = readw(adc->base + JZ_ADC_REG_ADBDAT);
+			break;
+		}
+
+		clk_disable(adc->clk);
+
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->channel) {
+		case INGENIC_ADC_AUX:
+			*val = JZ_ADC_AUX_VREF;
+			*val2 = JZ_ADC_AUX_VREF_BITS;
+			break;
+		case INGENIC_ADC_BATTERY:
+			if (adc->low_vref_mode) {
+				*val = JZ_ADC_BATTERY_LOW_VREF;
+				*val2 = JZ_ADC_BATTERY_LOW_VREF_BITS;
+			} else {
+				*val = adc->soc_data->battery_high_vref;
+				*val2 = adc->soc_data->battery_high_vref_bits;
+			}
+			break;
+		}
+
+		return IIO_VAL_FRACTIONAL_LOG2;
+	default:
+		return -EINVAL;
+	}
+}
+
+static void ingenic_adc_clk_cleanup(void *data)
+{
+	clk_unprepare(data);
+}
+
+static const struct iio_info ingenic_adc_info = {
+	.write_raw = ingenic_adc_write_raw,
+	.read_raw = ingenic_adc_read_raw,
+	.read_avail = ingenic_adc_read_avail,
+};
+
+static const struct iio_chan_spec ingenic_channels[] = {
+	{
+		.extend_name = "aux",
+		.type = IIO_VOLTAGE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.indexed = 1,
+		.channel = INGENIC_ADC_AUX,
+	},
+	{
+		.extend_name = "battery",
+		.type = IIO_VOLTAGE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_separate_available = BIT(IIO_CHAN_INFO_RAW) |
+						BIT(IIO_CHAN_INFO_SCALE),
+		.indexed = 1,
+		.channel = INGENIC_ADC_BATTERY,
+	},
+};
+
+static int ingenic_adc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct iio_dev *iio_dev;
+	struct ingenic_adc *adc;
+	struct resource *mem_base;
+	const struct ingenic_adc_soc_data *soc_data;
+	int ret;
+
+	soc_data = device_get_match_data(dev);
+	if (!soc_data)
+		return -EINVAL;
+
+	iio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
+	if (!iio_dev)
+		return -ENOMEM;
+
+	adc = iio_priv(iio_dev);
+	mutex_init(&adc->lock);
+	adc->soc_data = soc_data;
+
+	mem_base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	adc->base = devm_ioremap_resource(dev, mem_base);
+	if (IS_ERR(adc->base)) {
+		dev_err(dev, "Unable to ioremap mmio resource\n");
+		return PTR_ERR(adc->base);
+	}
+
+	adc->clk = devm_clk_get(dev, "adc");
+	if (IS_ERR(adc->clk)) {
+		dev_err(dev, "Unable to get clock\n");
+		return PTR_ERR(adc->clk);
+	}
+
+	ret = clk_prepare_enable(adc->clk);
+	if (ret) {
+		dev_err(dev, "Failed to enable clock\n");
+		return ret;
+	}
+
+	/* Put hardware in a known passive state. */
+	writeb(0x00, adc->base + JZ_ADC_REG_ENABLE);
+	writeb(0xff, adc->base + JZ_ADC_REG_CTRL);
+	clk_disable(adc->clk);
+
+	ret = devm_add_action_or_reset(dev, ingenic_adc_clk_cleanup, adc->clk);
+	if (ret) {
+		dev_err(dev, "Unable to add action\n");
+		return ret;
+	}
+
+	iio_dev->dev.parent = dev;
+	iio_dev->name = "jz-adc";
+	iio_dev->modes = INDIO_DIRECT_MODE;
+	iio_dev->channels = ingenic_channels;
+	iio_dev->num_channels = ARRAY_SIZE(ingenic_channels);
+	iio_dev->info = &ingenic_adc_info;
+
+	ret = devm_iio_device_register(dev, iio_dev);
+	if (ret)
+		dev_err(dev, "Unable to register IIO device\n");
+
+	return ret;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id ingenic_adc_of_match[] = {
+	{ .compatible = "ingenic,jz4725b-adc", .data = &jz4725b_adc_soc_data, },
+	{ .compatible = "ingenic,jz4740-adc", .data = &jz4740_adc_soc_data, },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ingenic_adc_of_match);
+#endif
+
+static struct platform_driver ingenic_adc_driver = {
+	.driver = {
+		.name = "ingenic-adc",
+		.of_match_table = of_match_ptr(ingenic_adc_of_match),
+	},
+	.probe = ingenic_adc_probe,
+};
+module_platform_driver(ingenic_adc_driver);
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/adc/lpc32xx_adc.c b/drivers/iio/adc/lpc32xx_adc.c
index 20b36690fa4f..e361c1532a75 100644
--- a/drivers/iio/adc/lpc32xx_adc.c
+++ b/drivers/iio/adc/lpc32xx_adc.c
@@ -1,23 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0+
 /*
  *  lpc32xx_adc.c - Support for ADC in LPC32XX
  *
  *  3-channel, 10-bit ADC
  *
  *  Copyright (C) 2011, 2012 Roland Stigge <stigge@antcom.de>
- *
- *  This program is free software; you can redistribute it and/or modify
- *  it under the terms of the GNU General Public License as published by
- *  the Free Software Foundation; either version 2 of the License, or
- *  (at your option) any later version.
- *
- *  This program is distributed in the hope that it will be useful,
- *  but WITHOUT ANY WARRANTY; without even the implied warranty of
- *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *  GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with this program; if not, write to the Free Software
- *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
 #include <linux/module.h>
diff --git a/drivers/iio/adc/ti-ads124s08.c b/drivers/iio/adc/ti-ads124s08.c
index c2cf58908fc8..53f17e4f2f23 100644
--- a/drivers/iio/adc/ti-ads124s08.c
+