Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 8214 insertions, 0 deletions

diff --git a/drivers/char/synclink.c b/drivers/char/synclink.c
new file mode 100644
index 000000000000..37c8bea8e2b0
--- /dev/null
+++ b/drivers/char/synclink.c
@@ -0,0 +1,8214 @@
+/*
+ * linux/drivers/char/synclink.c
+ *
+ * $Id: synclink.c,v 4.28 2004/08/11 19:30:01 paulkf Exp $
+ *
+ * Device driver for Microgate SyncLink ISA and PCI
+ * high speed multiprotocol serial adapters.
+ *
+ * written by Paul Fulghum for Microgate Corporation
+ * paulkf@microgate.com
+ *
+ * Microgate and SyncLink are trademarks of Microgate Corporation
+ *
+ * Derived from serial.c written by Theodore Ts'o and Linus Torvalds
+ *
+ * Original release 01/11/99
+ *
+ * This code is released under the GNU General Public License (GPL)
+ *
+ * This driver is primarily intended for use in synchronous
+ * HDLC mode. Asynchronous mode is also provided.
+ *
+ * When operating in synchronous mode, each call to mgsl_write()
+ * contains exactly one complete HDLC frame. Calling mgsl_put_char
+ * will start assembling an HDLC frame that will not be sent until
+ * mgsl_flush_chars or mgsl_write is called.
+ * 
+ * Synchronous receive data is reported as complete frames. To accomplish
+ * this, the TTY flip buffer is bypassed (too small to hold largest
+ * frame and may fragment frames) and the line discipline
+ * receive entry point is called directly.
+ *
+ * This driver has been tested with a slightly modified ppp.c driver
+ * for synchronous PPP.
+ *
+ * 2000/02/16
+ * Added interface for syncppp.c driver (an alternate synchronous PPP
+ * implementation that also supports Cisco HDLC). Each device instance
+ * registers as a tty device AND a network device (if dosyncppp option
+ * is set for the device). The functionality is determined by which
+ * device interface is opened.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
+ * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ * OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#if defined(__i386__)
+#  define BREAKPOINT() asm("   int $3");
+#else
+#  define BREAKPOINT() { }
+#endif
+
+#define MAX_ISA_DEVICES 10
+#define MAX_PCI_DEVICES 10
+#define MAX_TOTAL_DEVICES 20
+
+#include <linux/config.h>	
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/timer.h>
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial.h>
+#include <linux/major.h>
+#include <linux/string.h>
+#include <linux/fcntl.h>
+#include <linux/ptrace.h>
+#include <linux/ioport.h>
+#include <linux/mm.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+
+#include <linux/netdevice.h>
+
+#include <linux/vmalloc.h>
+#include <linux/init.h>
+#include <asm/serial.h>
+
+#include <linux/delay.h>
+#include <linux/ioctl.h>
+
+#include <asm/system.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/dma.h>
+#include <linux/bitops.h>
+#include <asm/types.h>
+#include <linux/termios.h>
+#include <linux/workqueue.h>
+#include <linux/hdlc.h>
+
+#ifdef CONFIG_HDLC_MODULE
+#define CONFIG_HDLC 1
+#endif
+
+#define GET_USER(error,value,addr) error = get_user(value,addr)
+#define COPY_FROM_USER(error,dest,src,size) error = copy_from_user(dest,src,size) ? -EFAULT : 0
+#define PUT_USER(error,value,addr) error = put_user(value,addr)
+#define COPY_TO_USER(error,dest,src,size) error = copy_to_user(dest,src,size) ? -EFAULT : 0
+
+#include <asm/uaccess.h>
+
+#include "linux/synclink.h"
+
+#define RCLRVALUE 0xffff
+
+static MGSL_PARAMS default_params = {
+	MGSL_MODE_HDLC,			/* unsigned long mode */
+	0,				/* unsigned char loopback; */
+	HDLC_FLAG_UNDERRUN_ABORT15,	/* unsigned short flags; */
+	HDLC_ENCODING_NRZI_SPACE,	/* unsigned char encoding; */
+	0,				/* unsigned long clock_speed; */
+	0xff,				/* unsigned char addr_filter; */
+	HDLC_CRC_16_CCITT,		/* unsigned short crc_type; */
+	HDLC_PREAMBLE_LENGTH_8BITS,	/* unsigned char preamble_length; */
+	HDLC_PREAMBLE_PATTERN_NONE,	/* unsigned char preamble; */
+	9600,				/* unsigned long data_rate; */
+	8,				/* unsigned char data_bits; */
+	1,				/* unsigned char stop_bits; */
+	ASYNC_PARITY_NONE		/* unsigned char parity; */
+};
+
+#define SHARED_MEM_ADDRESS_SIZE 0x40000
+#define BUFFERLISTSIZE (PAGE_SIZE)
+#define DMABUFFERSIZE (PAGE_SIZE)
+#define MAXRXFRAMES 7
+
+typedef struct _DMABUFFERENTRY
+{
+	u32 phys_addr;	/* 32-bit flat physical address of data buffer */
+	u16 count;	/* buffer size/data count */
+	u16 status;	/* Control/status field */
+	u16 rcc;	/* character count field */
+	u16 reserved;	/* padding required by 16C32 */
+	u32 link;	/* 32-bit flat link to next buffer entry */
+	char *virt_addr;	/* virtual address of data buffer */
+	u32 phys_entry;	/* physical address of this buffer entry */
+} DMABUFFERENTRY, *DMAPBUFFERENTRY;
+
+/* The queue of BH actions to be performed */
+
+#define BH_RECEIVE  1
+#define BH_TRANSMIT 2
+#define BH_STATUS   4
+
+#define IO_PIN_SHUTDOWN_LIMIT 100
+
+#define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
+
+struct	_input_signal_events {
+	int	ri_up;	
+	int	ri_down;
+	int	dsr_up;
+	int	dsr_down;
+	int	dcd_up;
+	int	dcd_down;
+	int	cts_up;
+	int	cts_down;
+};
+
+/* transmit holding buffer definitions*/
+#define MAX_TX_HOLDING_BUFFERS 5
+struct tx_holding_buffer {
+	int	buffer_size;
+	unsigned char *	buffer;
+};
+
+
+/*
+ * Device instance data structure
+ */
+ 
+struct mgsl_struct {
+	int			magic;
+	int			flags;
+	int			count;		/* count of opens */
+	int			line;
+	int                     hw_version;
+	unsigned short		close_delay;
+	unsigned short		closing_wait;	/* time to wait before closing */
+	
+	struct mgsl_icount	icount;
+	
+	struct tty_struct 	*tty;
+	int			timeout;
+	int			x_char;		/* xon/xoff character */
+	int			blocked_open;	/* # of blocked opens */
+	u16			read_status_mask;
+	u16			ignore_status_mask;	
+	unsigned char 		*xmit_buf;
+	int			xmit_head;
+	int			xmit_tail;
+	int			xmit_cnt;
+	
+	wait_queue_head_t	open_wait;
+	wait_queue_head_t	close_wait;
+	
+	wait_queue_head_t	status_event_wait_q;
+	wait_queue_head_t	event_wait_q;
+	struct timer_list	tx_timer;	/* HDLC transmit timeout timer */
+	struct mgsl_struct	*next_device;	/* device list link */
+	
+	spinlock_t irq_spinlock;		/* spinlock for synchronizing with ISR */
+	struct work_struct task;		/* task structure for scheduling bh */
+
+	u32 EventMask;			/* event trigger mask */
+	u32 RecordedEvents;		/* pending events */
+
+	u32 max_frame_size;		/* as set by device config */
+
+	u32 pending_bh;
+
+	int bh_running;		/* Protection from multiple */
+	int isr_overflow;
+	int bh_requested;
+	
+	int dcd_chkcount;		/* check counts to prevent */
+	int cts_chkcount;		/* too many IRQs if a signal */
+	int dsr_chkcount;		/* is floating */
+	int ri_chkcount;
+
+	char *buffer_list;		/* virtual address of Rx & Tx buffer lists */
+	unsigned long buffer_list_phys;
+
+	unsigned int rx_buffer_count;	/* count of total allocated Rx buffers */
+	DMABUFFERENTRY *rx_buffer_list;	/* list of receive buffer entries */
+	unsigned int current_rx_buffer;
+
+	int num_tx_dma_buffers;		/* number of tx dma frames required */
+ 	int tx_dma_buffers_used;
+	unsigned int tx_buffer_count;	/* count of total allocated Tx buffers */
+	DMABUFFERENTRY *tx_buffer_list;	/* list of transmit buffer entries */
+	int start_tx_dma_buffer;	/* tx dma buffer to start tx dma operation */
+	int current_tx_buffer;          /* next tx dma buffer to be loaded */
+	
+	unsigned char *intermediate_rxbuffer;
+
+	int num_tx_holding_buffers;	/* number of tx holding buffer allocated */
+	int get_tx_holding_index;  	/* next tx holding buffer for adapter to load */
+	int put_tx_holding_index;  	/* next tx holding buffer to store user request */
+	int tx_holding_count;		/* number of tx holding buffers waiting */
+	struct tx_holding_buffer tx_holding_buffers[MAX_TX_HOLDING_BUFFERS];
+
+	int rx_enabled;
+	int rx_overflow;
+	int rx_rcc_underrun;
+
+	int tx_enabled;
+	int tx_active;
+	u32 idle_mode;
+
+	u16 cmr_value;
+	u16 tcsr_value;
+
+	char device_name[25];		/* device instance name */
+
+	unsigned int bus_type;	/* expansion bus type (ISA,EISA,PCI) */
+	unsigned char bus;		/* expansion bus number (zero based) */
+	unsigned char function;		/* PCI device number */
+
+	unsigned int io_base;		/* base I/O address of adapter */
+	unsigned int io_addr_size;	/* size of the I/O address range */
+	int io_addr_requested;		/* nonzero if I/O address requested */
+	
+	unsigned int irq_level;		/* interrupt level */
+	unsigned long irq_flags;
+	int irq_requested;		/* nonzero if IRQ requested */
+	
+	unsigned int dma_level;		/* DMA channel */
+	int dma_requested;		/* nonzero if dma channel requested */
+
+	u16 mbre_bit;
+	u16 loopback_bits;
+	u16 usc_idle_mode;
+
+	MGSL_PARAMS params;		/* communications parameters */
+
+	unsigned char serial_signals;	/* current serial signal states */
+
+	int irq_occurred;		/* for diagnostics use */
+	unsigned int init_error;	/* Initialization startup error 		(DIAGS)	*/
+	int	fDiagnosticsmode;	/* Driver in Diagnostic mode?			(DIAGS)	*/
+
+	u32 last_mem_alloc;
+	unsigned char* memory_base;	/* shared memory address (PCI only) */
+	u32 phys_memory_base;
+	int shared_mem_requested;
+
+	unsigned char* lcr_base;	/* local config registers (PCI only) */
+	u32 phys_lcr_base;
+	u32 lcr_offset;
+	int lcr_mem_requested;
+
+	u32 misc_ctrl_value;
+	char flag_buf[MAX_ASYNC_BUFFER_SIZE];
+	char char_buf[MAX_ASYNC_BUFFER_SIZE];	
+	BOOLEAN drop_rts_on_tx_done;
+
+	BOOLEAN loopmode_insert_requested;
+	BOOLEAN	loopmode_send_done_requested;
+	
+	struct	_input_signal_events	input_signal_events;
+
+	/* generic HDLC device parts */
+	int netcount;
+	int dosyncppp;
+	spinlock_t netlock;
+
+#ifdef CONFIG_HDLC
+	struct net_device *netdev;
+#endif
+};
+
+#define MGSL_MAGIC 0x5401
+
+/*
+ * The size of the serial xmit buffer is 1 page, or 4096 bytes
+ */
+#ifndef SERIAL_XMIT_SIZE
+#define SERIAL_XMIT_SIZE 4096
+#endif
+
+/*
+ * These macros define the offsets used in calculating the
+ * I/O address of the specified USC registers.
+ */
+
+
+#define DCPIN 2		/* Bit 1 of I/O address */
+#define SDPIN 4		/* Bit 2 of I/O address */
+
+#define DCAR 0		/* DMA command/address register */
+#define CCAR SDPIN		/* channel command/address register */
+#define DATAREG DCPIN + SDPIN	/* serial data register */
+#define MSBONLY 0x41
+#define LSBONLY 0x40
+
+/*
+ * These macros define the register address (ordinal number)
+ * used for writing address/value pairs to the USC.
+ */
+
+#define CMR	0x02	/* Channel mode Register */
+#define CCSR	0x04	/* Channel Command/status Register */
+#define CCR	0x06	/* Channel Control Register */
+#define PSR	0x08	/* Port status Register */
+#define PCR	0x0a	/* Port Control Register */
+#define TMDR	0x0c	/* Test mode Data Register */
+#define TMCR	0x0e	/* Test mode Control Register */
+#define CMCR	0x10	/* Clock mode Control Register */
+#define HCR	0x12	/* Hardware Configuration Register */
+#define IVR	0x14	/* Interrupt Vector Register */
+#define IOCR	0x16	/* Input/Output Control Register */
+#define ICR	0x18	/* Interrupt Control Register */
+#define DCCR	0x1a	/* Daisy Chain Control Register */
+#define MISR	0x1c	/* Misc Interrupt status Register */
+#define SICR	0x1e	/* status Interrupt Control Register */
+#define RDR	0x20	/* Receive Data Register */
+#define RMR	0x22	/* Receive mode Register */
+#define RCSR	0x24	/* Receive Command/status Register */
+#define RICR	0x26	/* Receive Interrupt Control Register */
+#define RSR	0x28	/* Receive Sync Register */
+#define RCLR	0x2a	/* Receive count Limit Register */
+#define RCCR	0x2c	/* Receive Character count Register */
+#define TC0R	0x2e	/* Time Constant 0 Register */
+#define TDR	0x30	/* Transmit Data Register */
+#define TMR	0x32	/* Transmit mode Register */
+#define TCSR	0x34	/* Transmit Command/status Register */
+#define TICR	0x36	/* Transmit Interrupt Control Register */
+#define TSR	0x38	/* Transmit Sync Register */
+#define TCLR	0x3a	/* Transmit count Limit Register */
+#define TCCR	0x3c	/* Transmit Character count Register */
+#define TC1R	0x3e	/* Time Constant 1 Register */
+
+
+/*
+ * MACRO DEFINITIONS FOR DMA REGISTERS
+ */
+
+#define DCR	0x06	/* DMA Control Register (shared) */
+#define DACR	0x08	/* DMA Array count Register (shared) */
+#define BDCR	0x12	/* Burst/Dwell Control Register (shared) */
+#define DIVR	0x14	/* DMA Interrupt Vector Register (shared) */	
+#define DICR	0x18	/* DMA Interrupt Control Register (shared) */
+#define CDIR	0x1a	/* Clear DMA Interrupt Register (shared) */
+#define SDIR	0x1c	/* Set DMA Interrupt Register (shared) */
+
+#define TDMR	0x02	/* Transmit DMA mode Register */
+#define TDIAR	0x1e	/* Transmit DMA Interrupt Arm Register */
+#define TBCR	0x2a	/* Transmit Byte count Register */
+#define TARL	0x2c	/* Transmit Address Register (low) */
+#define TARU	0x2e	/* Transmit Address Register (high) */
+#define NTBCR	0x3a	/* Next Transmit Byte count Register */
+#define NTARL	0x3c	/* Next Transmit Address Register (low) */
+#define NTARU	0x3e	/* Next Transmit Address Register (high) */
+
+#define RDMR	0x82	/* Receive DMA mode Register (non-shared) */
+#define RDIAR	0x9e	/* Receive DMA Interrupt Arm Register */
+#define RBCR	0xaa	/* Receive Byte count Register */
+#define RARL	0xac	/* Receive Address Register (low) */
+#define RARU	0xae	/* Receive Address Register (high) */
+#define NRBCR	0xba	/* Next Receive Byte count Register */
+#define NRARL	0xbc	/* Next Receive Address Register (low) */
+#define NRARU	0xbe	/* Next Receive Address Register (high) */
+
+
+/*
+ * MACRO DEFINITIONS FOR MODEM STATUS BITS
+ */
+
+#define MODEMSTATUS_DTR 0x80
+#define MODEMSTATUS_DSR 0x40
+#define MODEMSTATUS_RTS 0x20
+#define MODEMSTATUS_CTS 0x10
+#define MODEMSTATUS_RI  0x04
+#define MODEMSTATUS_DCD 0x01
+
+
+/*
+ * Channel Command/Address Register (CCAR) Command Codes
+ */
+
+#define RTCmd_Null			0x0000
+#define RTCmd_ResetHighestIus		0x1000
+#define RTCmd_TriggerChannelLoadDma	0x2000
+#define RTCmd_TriggerRxDma		0x2800
+#define RTCmd_TriggerTxDma		0x3000
+#define RTCmd_TriggerRxAndTxDma		0x3800
+#define RTCmd_PurgeRxFifo		0x4800
+#define RTCmd_PurgeTxFifo		0x5000
+#define RTCmd_PurgeRxAndTxFifo		0x5800
+#define RTCmd_LoadRcc			0x6800
+#define RTCmd_LoadTcc			0x7000
+#define RTCmd_LoadRccAndTcc		0x7800
+#define RTCmd_LoadTC0			0x8800
+#define RTCmd_LoadTC1			0x9000
+#define RTCmd_LoadTC0AndTC1		0x9800
+#define RTCmd_SerialDataLSBFirst	0xa000
+#define RTCmd_SerialDataMSBFirst	0xa800
+#define RTCmd_SelectBigEndian		0xb000
+#define RTCmd_SelectLittleEndian	0xb800
+
+
+/*
+ * DMA Command/Address Register (DCAR) Command Codes
+ */
+
+#define DmaCmd_Null			0x0000
+#define DmaCmd_ResetTxChannel		0x1000
+#define DmaCmd_ResetRxChannel		0x1200
+#define DmaCmd_StartTxChannel		0x2000
+#define DmaCmd_StartRxChannel		0x2200
+#define DmaCmd_ContinueTxChannel	0x3000
+#define DmaCmd_ContinueRxChannel	0x3200
+#define DmaCmd_PauseTxChannel		0x4000
+#define DmaCmd_PauseRxChannel		0x4200
+#define DmaCmd_AbortTxChannel		0x5000
+#define DmaCmd_AbortRxChannel		0x5200
+#define DmaCmd_InitTxChannel		0x7000
+#define DmaCmd_InitRxChannel		0x7200
+#define DmaCmd_ResetHighestDmaIus	0x8000
+#define DmaCmd_ResetAllChannels		0x9000
+#define DmaCmd_StartAllChannels		0xa000
+#define DmaCmd_ContinueAllChannels	0xb000
+#define DmaCmd_PauseAllChannels		0xc000
+#define DmaCmd_AbortAllChannels		0xd000
+#define DmaCmd_InitAllChannels		0xf000
+
+#define TCmd_Null			0x0000
+#define TCmd_ClearTxCRC			0x2000
+#define TCmd_SelectTicrTtsaData		0x4000
+#define TCmd_SelectTicrTxFifostatus	0x5000
+#define TCmd_SelectTicrIntLevel		0x6000
+#define TCmd_SelectTicrdma_level		0x7000
+#define TCmd_SendFrame			0x8000
+#define TCmd_SendAbort			0x9000
+#define TCmd_EnableDleInsertion		0xc000
+#define TCmd_DisableDleInsertion	0xd000
+#define TCmd_ClearEofEom		0xe000
+#define TCmd_SetEofEom			0xf000
+
+#define RCmd_Null			0x0000
+#define RCmd_ClearRxCRC			0x2000
+#define RCmd_EnterHuntmode		0x3000
+#define RCmd_SelectRicrRtsaData		0x4000
+#define RCmd_SelectRicrRxFifostatus	0x5000
+#define RCmd_SelectRicrIntLevel		0x6000
+#define RCmd_SelectRicrdma_level		0x7000
+
+/*
+ * Bits for enabling and disabling IRQs in Interrupt Control Register (ICR)
+ */
+ 
+#define RECEIVE_STATUS		BIT5
+#define RECEIVE_DATA		BIT4
+#define TRANSMIT_STATUS		BIT3
+#define TRANSMIT_DATA		BIT2
+#define IO_PIN			BIT1
+#define MISC			BIT0
+
+
+/*
+ * Receive status Bits in Receive Command/status Register RCSR
+ */
+
+#define RXSTATUS_SHORT_FRAME		BIT8
+#define RXSTATUS_CODE_VIOLATION		BIT8
+#define RXSTATUS_EXITED_HUNT		BIT7
+#define RXSTATUS_IDLE_RECEIVED		BIT6
+#define RXSTATUS_BREAK_RECEIVED		BIT5
+#define RXSTATUS_ABORT_RECEIVED		BIT5
+#define RXSTATUS_RXBOUND		BIT4
+#define RXSTATUS_CRC_ERROR		BIT3
+#define RXSTATUS_FRAMING_ERROR		BIT3
+#define RXSTATUS_ABORT			BIT2
+#define RXSTATUS_PARITY_ERROR		BIT2
+#define RXSTATUS_OVERRUN		BIT1
+#define RXSTATUS_DATA_AVAILABLE		BIT0
+#define RXSTATUS_ALL			0x01f6
+#define usc_UnlatchRxstatusBits(a,b) usc_OutReg( (a), RCSR, (u16)((b) & RXSTATUS_ALL) )
+
+/*
+ * Values for setting transmit idle mode in 
+ * Transmit Control/status Register (TCSR)
+ */
+#define IDLEMODE_FLAGS			0x0000
+#define IDLEMODE_ALT_ONE_ZERO		0x0100
+#define IDLEMODE_ZERO			0x0200
+#define IDLEMODE_ONE			0x0300
+#define IDLEMODE_ALT_MARK_SPACE		0x0500
+#define IDLEMODE_SPACE			0x0600
+#define IDLEMODE_MARK			0x0700
+#define IDLEMODE_MASK			0x0700
+
+/*
+ * IUSC revision identifiers
+ */
+#define	IUSC_SL1660			0x4d44
+#define IUSC_PRE_SL1660			0x4553
+
+/*
+ * Transmit status Bits in Transmit Command/status Register (TCSR)
+ */
+
+#define TCSR_PRESERVE			0x0F00
+
+#define TCSR_UNDERWAIT			BIT11
+#define TXSTATUS_PREAMBLE_SENT		BIT7
+#define TXSTATUS_IDLE_SENT		BIT6
+#define TXSTATUS_ABORT_SENT		BIT5
+#define TXSTATUS_EOF_SENT		BIT4
+#define TXSTATUS_EOM_SENT		BIT4
+#define TXSTATUS_CRC_SENT		BIT3
+#define TXSTATUS_ALL_SENT		BIT2
+#define TXSTATUS_UNDERRUN		BIT1
+#define TXSTATUS_FIFO_EMPTY		BIT0
+#define TXSTATUS_ALL			0x00fa
+#define usc_UnlatchTxstatusBits(a,b) usc_OutReg( (a), TCSR, (u16)((a)->tcsr_value + ((b) & 0x00FF)) )
+				
+
+#define MISCSTATUS_RXC_LATCHED		BIT15
+#define MISCSTATUS_RXC			BIT14
+#define MISCSTATUS_TXC_LATCHED		BIT13
+#define MISCSTATUS_TXC			BIT12
+#define MISCSTATUS_RI_LATCHED		BIT11
+#define MISCSTATUS_RI			BIT10
+#define MISCSTATUS_DSR_LATCHED		BIT9
+#define MISCSTATUS_DSR			BIT8
+#define MISCSTATUS_DCD_LATCHED		BIT7
+#define MISCSTATUS_DCD			BIT6
+#define MISCSTATUS_CTS_LATCHED		BIT5
+#define MISCSTATUS_CTS			BIT4
+#define MISCSTATUS_RCC_UNDERRUN		BIT3
+#define MISCSTATUS_DPLL_NO_SYNC		BIT2
+#define MISCSTATUS_BRG1_ZERO		BIT1
+#define MISCSTATUS_BRG0_ZERO		BIT0
+
+#define usc_UnlatchIostatusBits(a,b) usc_OutReg((a),MISR,(u16)((b) & 0xaaa0))
+#define usc_UnlatchMiscstatusBits(a,b) usc_OutReg((a),MISR,(u16)((b) & 0x000f))
+
+#define SICR_RXC_ACTIVE			BIT15
+#define SICR_RXC_INACTIVE		BIT14
+#define SICR_RXC			(BIT15+BIT14)
+#define SICR_TXC_ACTIVE			BIT13
+#define SICR_TXC_INACTIVE		BIT12
+#define SICR_TXC			(BIT13+BIT12)
+#define SICR_RI_ACTIVE			BIT11
+#define SICR_RI_INACTIVE		BIT10
+#define SICR_RI				(BIT11+BIT10)
+#define SICR_DSR_ACTIVE			BIT9
+#define SICR_DSR_INACTIVE		BIT8
+#define SICR_DSR			(BIT9+BIT8)
+#define SICR_DCD_ACTIVE			BIT7
+#define SICR_DCD_INACTIVE		BIT6
+#define SICR_DCD			(BIT7+BIT6)
+#define SICR_CTS_ACTIVE			BIT5
+#define SICR_CTS_INACTIVE		BIT4
+#define SICR_CTS			(BIT5+BIT4)
+#define SICR_RCC_UNDERFLOW		BIT3
+#define SICR_DPLL_NO_SYNC		BIT2
+#define SICR_BRG1_ZERO			BIT1
+#define SICR_BRG0_ZERO			BIT0
+
+void usc_DisableMasterIrqBit( struct mgsl_struct *info );
+void usc_EnableMasterIrqBit( struct mgsl_struct *info );
+void usc_EnableInterrupts( struct mgsl_struct *info, u16 IrqMask );
+void usc_DisableInterrupts( struct mgsl_struct *info, u16 IrqMask );
+void usc_ClearIrqPendingBits( struct mgsl_struct *info, u16 IrqMask );
+
+#define usc_EnableInterrupts( a, b ) \
+	usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0xff00) + 0xc0 + (b)) )
+
+#define usc_DisableInterrupts( a, b ) \
+	usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0xff00) + 0x80 + (b)) )
+
+#define usc_EnableMasterIrqBit(a) \
+	usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0x0f00) + 0xb000) )
+
+#define usc_DisableMasterIrqBit(a) \
+	usc_OutReg( (a), ICR, (u16)(usc_InReg((a),ICR) & 0x7f00) )
+
+#define usc_ClearIrqPendingBits( a, b ) usc_OutReg( (a), DCCR, 0x40 + (b) )
+
+/*
+ * Transmit status Bits in Transmit Control status Register (TCSR)
+ * and Transmit Interrupt Control Register (TICR) (except BIT2, BIT0)
+ */
+
+#define TXSTATUS_PREAMBLE_SENT	BIT7
+#define TXSTATUS_IDLE_SENT	BIT6
+#define TXSTATUS_ABORT_SENT	BIT5
+#define TXSTATUS_EOF		BIT4
+#define TXSTATUS_CRC_SENT	BIT3
+#define TXSTATUS_ALL_SENT	BIT2
+#define TXSTATUS_UNDERRUN	BIT1
+#define TXSTATUS_FIFO_EMPTY	BIT0
+
+#define DICR_MASTER		BIT15
+#define DICR_TRANSMIT		BIT0
+#define DICR_RECEIVE		BIT1
+
+#define usc_EnableDmaInterrupts(a,b) \
+	usc_OutDmaReg( (a), DICR, (u16)(usc_InDmaReg((a),DICR) | (b)) )
+
+#define usc_DisableDmaInterrupts(a,b) \
+	usc_OutDmaReg( (a), DICR, (u16)(usc_InDmaReg((a),DICR) & ~(b)) )
+
+#define usc_EnableStatusIrqs(a,b) \
+	usc_OutReg( (a), SICR, (u16)(usc_InReg((a),SICR) | (b)) )
+
+#define usc_DisablestatusIrqs(a,b) \
+	usc_OutReg( (a), SICR, (u16)(usc_InReg((a),SICR) & ~(b)) )
+
+/* Transmit status Bits in Transmit Control status Register (TCSR) */
+/* and Transmit Interrupt Control Register (TICR) (except BIT2, BIT0) */
+
+
+#define DISABLE_UNCONDITIONAL    0
+#define DISABLE_END_OF_FRAME     1
+#define ENABLE_UNCONDITIONAL     2
+#define ENABLE_AUTO_CTS          3
+#define ENABLE_AUTO_DCD          3
+#define usc_EnableTransmitter(a,b) \
+	usc_OutReg( (a), TMR, (u16)((usc_InReg((a),TMR) & 0xfffc) | (b)) )
+#define usc_EnableReceiver(a,b) \
+	usc_OutReg( (a), RMR, (u16)((usc_InReg((a),RMR) & 0xfffc) | (b)) )
+
+static u16  usc_InDmaReg( struct mgsl_struct *info, u16 Port );
+static void usc_OutDmaReg( struct mgsl_struct *info, u16 Port, u16 Value );
+static void usc_DmaCmd( struct mgsl_struct *info, u16 Cmd );
+
+static u16  usc_InReg( struct mgsl_struct *info, u16 Port );
+static void usc_OutReg( struct mgsl_struct *info, u16 Port, u16 Value );
+static void usc_RTCmd( struct mgsl_struct *info, u16 Cmd );
+void usc_RCmd( struct mgsl_struct *info, u16 Cmd );
+void usc_TCmd( struct mgsl_struct *info, u16 Cmd );
+
+#define usc_TCmd(a,b) usc_OutReg((a), TCSR, (u16)((a)->tcsr_value + (b)))
+#define usc_RCmd(a,b) usc_OutReg((a), RCSR, (b))
+
+#define usc_SetTransmitSyncChars(a,s0,s1) usc_OutReg((a), TSR, (u16)(((u16)s0<<8)|(u16)s1))
+
+static void usc_process_rxoverrun_sync( struct mgsl_struct *info );
+static void usc_start_receiver( struct mgsl_struct *info );
+static void usc_stop_receiver( struct mgsl_struct *info );
+
+static void usc_start_transmitter( struct mgsl_struct *info );
+static void usc_stop_transmitter( struct mgsl_struct *info );
+static void usc_set_txidle( struct mgsl_struct *info );
+static void usc_load_txfifo( struct mgsl_struct *info );
+
+static void usc_enable_aux_clock( struct mgsl_struct *info, u32 DataRate );
+static void usc_enable_loopback( struct mgsl_struct *info, int enable );
+
+static void usc_get_serial_signals( struct mgsl_struct *info );
+static void usc_set_serial_signals( struct mgsl_struct *info );
+
+static void usc_reset( struct mgsl_struct *info );
+
+static void usc_set_sync_mode( struct mgsl_struct *info );
+static void usc_set_sdlc_mode( struct mgsl_struct *info );
+static void usc_set_async_mode( struct mgsl_struct *info );
+static void usc_enable_async_clock( struct mgsl_struct *info, u32 DataRate );
+
+static void usc_loopback_frame( struct mgsl_struct *info );
+
+static void mgsl_tx_timeout(unsigned long context);
+
+
+static void usc_loopmode_cancel_transmit( struct mgsl_struct * info );
+static void usc_loopmode_insert_request( struct mgsl_struct * info );
+static int usc_loopmode_active( struct mgsl_struct * info);
+static void usc_loopmode_send_done( struct mgsl_struct * info );
+
+static int mgsl_ioctl_common(struct mgsl_struct *info, unsigned int cmd, unsigned long arg);
+
+#ifdef CONFIG_HDLC
+#define dev_to_port(D) (dev_to_hdlc(D)->priv)
+static void hdlcdev_tx_done(struct mgsl_struct *info);
+static void hdlcdev_rx(struct mgsl_struct *info, char *buf, int size);
+static int  hdlcdev_init(struct mgsl_struct *info);
+static void hdlcdev_exit(struct mgsl_struct *info);
+#endif
+
+/*
+ * Defines a BUS descriptor value for the PCI adapter
+ * local bus address ranges.
+ */
+
+#define BUS_DESCRIPTOR( WrHold, WrDly, RdDly, Nwdd, Nwad, Nxda, Nrdd, Nrad ) \
+(0x00400020 + \
+((WrHold) << 30) + \
+((WrDly)  << 28) + \
+((RdDly)  << 26) + \
+((Nwdd)   << 20) + \
+((Nwad)   << 15) + \
+((Nxda)   << 13) + \
+((Nrdd)   << 11) + \
+((Nrad)   <<  6) )
+
+static void mgsl_trace_block(struct mgsl_struct *info,const char* data, int count, int xmit);
+
+/*
+ * Adapter diagnostic routines
+ */
+static BOOLEAN mgsl_register_test( struct mgsl_struct *info );
+static BOOLEAN mgsl_irq_test( struct mgsl_struct *info );
+static BOOLEAN mgsl_dma_test( struct mgsl_struct *info );
+static BOOLEAN mgsl_memory_test( struct mgsl_struct *info );
+static int mgsl_adapter_test( struct mgsl_struct *info );
+
+/*
+ * device and resource management routines
+ */
+static int mgsl_claim_resources(struct mgsl_struct *info);
+static void mgsl_release_resources(struct mgsl_struct *info);
+static void mgsl_add_device(struct mgsl_struct *info);
+static struct mgsl_struct* mgsl_allocate_device(void);
+
+/*
+ * DMA buffer manupulation functions.
+ */
+static void mgsl_free_rx_frame_buffers( struct mgsl_struct *info, unsigned int StartIndex, unsigned int EndIndex );
+static int  mgsl_get_rx_frame( struct mgsl_struct *info );
+static int  mgsl_get_raw_rx_frame( struct mgsl_struct *info );
+static void mgsl_reset_rx_dma_buffers( struct mgsl_struct *info );
+static void mgsl_reset_tx_dma_buffers( struct mgsl_struct *info );
+static int num_free_tx_dma_buffers(struct mgsl_struct *info);
+static void mgsl_load_tx_dma_buffer( struct mgsl_struct *info, const char *Buffer, unsigned int BufferSize);
+static void mgsl_load_pci_memory(char* TargetPtr, const char* SourcePtr, unsigned short count);
+
+/*
+ * DMA and Shared Memory buffer allocation and formatting
+ */
+static int  mgsl_allocate_dma_buffers(struct mgsl_struct *info);
+static void mgsl_free_dma_buffers(struct mgsl_struct *info);
+static int  mgsl_alloc_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList,int Buffercount);
+static void mgsl_free_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList,int Buffercount);
+static int  mgsl_alloc_buffer_list_memory(struct mgsl_struct *info);
+static void mgsl_free_buffer_list_memory(struct mgsl_struct *info);
+static int mgsl_alloc_intermediate_rxbuffer_memory(struct mgsl_struct *info);
+static void mgsl_free_intermediate_rxbuffer_memory(struct mgsl_struct *info);
+static int mgsl_alloc_intermediate_txbuffer_memory(struct mgsl_struct *info);
+static void mgsl_free_intermediate_txbuffer_memory(struct mgsl_struct *info);
+static int load_next_tx_holding_buffer(struct mgsl_struct *info);
+static int save_tx_buffer_request(struct mgsl_struct *info,const char *Buffer, unsigned int BufferSize);
+
+/*
+ * Bottom half interrupt handlers
+ */
+static void mgsl_bh_handler(void* Context);
+static void mgsl_bh_receive(struct mgsl_struct *info);
+static void mgsl_bh_transmit(struct mgsl_struct *info);
+static void mgsl_bh_status(struct mgsl_struct *info);
+
+/*
+ * Interrupt handler routines and dispatch table.
+ */
+static void mgsl_isr_null( struct mgsl_struct *info );
+static void mgsl_isr_transmit_data( struct mgsl_struct *info );
+static void mgsl_isr_receive_data( struct mgsl_struct *info );
+static void mgsl_isr_receive_status( struct mgsl_struct *info );
+static void mgsl_isr_transmit_status( struct mgsl_struct *info );
+static void mgsl_isr_io_pin( struct mgsl_struct *info );
+static void mgsl_isr_misc( struct mgsl_struct *info );
+static void mgsl_isr_receive_dma( struct mgsl_struct *info );
+static void mgsl_isr_transmit_dma( struct mgsl_struct *info );
+
+typedef void (*isr_dispatch_func)(struct mgsl_struct *);
+
+static isr_dispatch_func UscIsrTable[7] =
+{
+	mgsl_isr_null,
+	mgsl_isr_misc,
+	mgsl_isr_io_pin,
+	mgsl_isr_transmit_data,
+	mgsl_isr_transmit_status,
+	mgsl_isr_receive_data,
+	mgsl_isr_receive_status
+};
+
+/*
+ * ioctl call handlers
+ */
+static int tiocmget(struct tty_struct *tty, struct file *file);
+static int tiocmset(struct tty_struct *tty, struct file *file,
+		    unsigned int set, unsigned int clear);
+static int mgsl_get_stats(struct mgsl_struct * info, struct mgsl_icount
+	__user *user_icount);
+static int mgsl_get_params(struct mgsl_struct * info, MGSL_PARAMS  __user *user_params);
+static int mgsl_set_params(struct mgsl_struct * info, MGSL_PARAMS  __user *new_params);
+static int mgsl_get_txidle(struct mgsl_struct * info, int __user *idle_mode);
+static int mgsl_set_txidle(struct mgsl_struct * info, int idle_mode);
+static int mgsl_txenable(struct mgsl_struct * info, int enable);
+static int mgsl_txabort(struct mgsl_struct * info);
+static int mgsl_rxenable(struct mgsl_struct * info, int enable);
+static int mgsl_wait_event(struct mgsl_struct * info, int __user *mask);
+static int mgsl_loopmode_send_done( struct mgsl_struct * info );
+
+/* set non-zero on successful registration with PCI subsystem */
+static int pci_registered;
+
+/*
+ * Global linked list of SyncLink devices
+ */
+static struct mgsl_struct *mgsl_device_list;
+static int mgsl_device_count;
+
+/*
+ * Set this param to non-zero to load eax with the
+ * .text section address and breakpoint on module load.
+ * This is useful for use with gdb and add-symbol-file command.
+ */
+static int break_on_load;
+
+/*
+ * Driver major number, defaults to zero to get auto
+ * assigned major number. May be forced as module parameter.
+ */
+static int ttymajor;
+
+/*
+ * Array of user specified options for ISA adapters.
+ */
+static int io[MAX_ISA_DEVICES];
+static int irq[MAX_ISA_DEVICES];
+static int dma[MAX_ISA_DEVICES];
+static int debug_level;
+static int maxframe[MAX_TOTAL_DEVICES];
+static int dosyncppp[MAX_TOTAL_DEVICES];
+static int txdmabufs[MAX_TOTAL_DEVICES];
+static int txholdbufs[MAX_TOTAL_DEVICES];
+	
+module_param(break_on_load, bool, 0);
+module_param(ttymajor, int, 0);
+module_param_array(io, int, NULL, 0);
+module_param_array(irq, int, NULL, 0);
+module_param_array(dma, int, NULL, 0);
+module_param(debug_level, int, 0);
+module_param_array(maxframe, int, NULL, 0);
+module_param_array(dosyncppp, int, NULL, 0);
+module_param_array(txdmabufs, int, NULL, 0);
+module_param_array(txholdbufs, int, NULL, 0);
+
+static char *driver_name = "SyncLink serial driver";
+static char *driver_version = "$Revision: 4.28 $";
+
+static int synclink_init_one (struct pci_dev *dev,
+				     const struct pci_device_id *ent);
+static void synclink_remove_one (struct pci_dev *dev);
+
+static struct pci_device_id synclink_pci_tbl[] = {
+	{ PCI_VENDOR_ID_MICROGATE, PCI_DEVICE_ID_MICROGATE_USC, PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_MICROGATE, 0x0210, PCI_ANY_ID, PCI_ANY_ID, },
+	{ 0, }, /* terminate list */
+};
+MODULE_DEVICE_TABLE(pci, synclink_pci_tbl);
+
+MODULE_LICENSE("GPL");
+
+static struct pci_driver synclink_pci_driver = {
+	.name		= "synclink",
+	.id_table	= synclink_pci_tbl,
+	.probe		= synclink_init_one,
+	.remove		= __devexit_p(synclink_remove_one),
+};
+
+static struct tty_driver *serial_driver;
+
+/* number of characters left in xmit buffer before we ask for more */
+#define WAKEUP_CHARS 256
+
+
+static void mgsl_change_params(struct mgsl_struct *info);
+static void mgsl_wait_until_sent(struct tty_struct *tty, int timeout);
+
+/*
+ * 1st function defined in .text section. Calling this function in
+ * init_module() followed by a breakpoint allows a remote debugger
+ * (gdb) to get the .text address for the add-symbol-file command.
+ * This allows remote debugging of dynamically loadable modules.
+ */
+static void* mgsl_get_text_ptr(void)
+{
+	return mgsl_get_text_ptr;
+}
+
+/*
+ * tmp_buf is used as a temporary buffer by mgsl_write.  We need to
+ * lock it in case the COPY_FROM_USER blocks while swapping in a page,
+ * and some other program tries to do a serial write at the same time.
+ * Since the lock will only come under contention when the system is
+ * swapping and available memory is low, it makes sense to share one
+ * buffer across all the serial ioports, since it significantly saves
+ * memory if large numbers of serial ports are open.
+ */
+static unsigned char *tmp_buf;
+static DECLARE_MUTEX(tmp_buf_sem);
+
+static inline int mgsl_paranoia_check(struct mgsl_struct *info,
+					char *name, const char *routine)
+{
+#ifdef MGSL_PARANOIA_CHECK
+	static const char *badmagic =
+		"Warning: bad magic number for mgsl struct (%s) in %s\n";
+	static const char *badinfo =
+		"Warning: null mgsl_struct for (%s) in %s\n";
+
+	if (!info) {
+		printk(badinfo, name, routine);
+		return 1;
+	}
+	if (info->magic != MGSL_MAGIC) {
+		printk(badmagic, name, routine);
+		return 1;
+	}
+#else
+	if (!info)
+		return 1;
+#endif
+	return 0;
+}
+
+/**
+ * line discipline callback wrappers
+ *
+ * The wrappers maintain line discipline references
+ * while calling into the line discipline.
+ *
+ * ldisc_receive_buf  - pass receive data to line discipline
+ */
+
+static void ldisc_receive_buf(struct tty_struct *tty,
+			      const __u8 *data, char *flags, int count)
+{
+	struct tty_ldisc *ld;
+	if (!tty)
+		return;
+	ld = tty_ldisc_ref(tty);
+	if (ld) {
+		if (ld->receive_buf)
+			ld->receive_buf(tty, data, flags, count);
+		tty_ldisc_deref(ld);
+	}
+}
+
+/* mgsl_stop()		throttle (stop) transmitter
+ * 	
+ * Arguments:		tty	pointer to tty info structure
+ * Return Value:	None
+ */
+static void mgsl_stop(struct tty_struct *tty)
+{
+	struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data;
+	unsigned long flags;
+	
+	if (mgsl_paranoia_check(info, tty->name, "mgsl_stop"))
+		return;
+	
+	if ( debug_level >= DEBUG_LEVEL_INFO )
+		printk("mgsl_stop(%s)\n",info->device_name);	
+		
+	spin_lock_irqsave(&info->irq_spinlock,flags);
+	if (info->tx_enabled)
+	 	usc_stop_transmitter(info);
+	spin_unlock_irqrestore(&info->irq_spinlock,flags);
+	
+}	/* end of mgsl_stop() */
+
+/* mgsl_start()		release (start) transmitter
+ * 	
+ * Arguments:		tty	pointer to tty info structure
+ * Return Value:	None
+ */
+static void mgsl_start(struct tty_struct *tty)
+{
+	struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data;
+	unsigned long flags;
+	
+	if (mgsl_paranoia_check(info, tty->name, "mgsl_start"))
+		return;
+	
+	if ( debug_level >= DEBUG_LEVEL_INFO )
+		printk("mgsl_start(%s)\n",info->device_name);	
+		
+	spin_lock_irqsave(&info->irq_spinlock,flags);
+	if (!info->tx_enabled)
+	 	usc_start_transmitter(inf