Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull ACPI and power management updates from Rafael Wysocki:
 "This time we have some more new material than we used to have during
  the last couple of development cycles.

  The most important part of it to me is the introduction of a unified
  interface for accessing device properties provided by platform
  firmware.  It works with Device Trees and ACPI in a uniform way and
  drivers using it need not worry about where the properties come from
  as long as the platform firmware (either DT or ACPI) makes them
  available.  It covers both devices and "bare" device node objects
  without struct device representation as that turns out to be necessary
  in some cases.  This has been in the works for quite a few months (and
  development cycles) and has been approved by all of the relevant
  maintainers.

  On top of that, some drivers are switched over to the new interface
  (at25, leds-gpio, gpio_keys_polled) and some additional changes are
  made to the core GPIO subsystem to allow device drivers to manipulate
  GPIOs in the "canonical" way on platforms that provide GPIO
  information in their ACPI tables, but don't assign names to GPIO lines
  (in which case the driver needs to do that on the basis of what it
  knows about the device in question).  That also has been approved by
  the GPIO core maintainers and the rfkill driver is now going to use
  it.

  Second is support for hardware P-states in the intel_pstate driver.
  It uses CPUID to detect whether or not the feature is supported by the
  processor in which case it will be enabled by default.  However, it
  can be disabled entirely from the kernel command line if necessary.

  Next is support for a platform firmware interface based on ACPI
  operation regions used by the PMIC (Power Management Integrated
  Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
  That interface is used for manipulating power resources and for
  thermal management: sensor temperature reporting, trip point setting
  and so on.

  Also the ACPI core is now going to support the _DEP configuration
  information in a limited way.  Basically, _DEP it supposed to reflect
  off-the-hierarchy dependencies between devices which may be very
  indirect, like when AML for one device accesses locations in an
  operation region handled by another device's driver (usually, the
  device depended on this way is a serial bus or GPIO controller).  The
  support added this time is sufficient to make the ACPI battery driver
  work on Asus T100A, but it is general enough to be able to cover some
  other use cases in the future.

  Finally, we have a new cpufreq driver for the Loongson1B processor.

  In addition to the above, there are fixes and cleanups all over the
  place as usual and a traditional ACPICA update to a recent upstream
  release.

  As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
  Intel platforms should be able to handle power management of the DMA
  engine correctly, the cpufreq-dt driver should interact with the
  thermal subsystem in a better way and the ACPI backlight driver should
  handle some more corner cases, among other things.

  On top of the ACPICA update there are fixes for race conditions in the
  ACPICA's interrupt handling code which might lead to some random and
  strange looking failures on some systems.

  In the cleanups department the most visible part is the series of
  commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
  option.  That was triggered by a discussion regarding the generic
  power domains code during which we realized that trying to support
  certain combinations of PM config options was painful and not really
  worth it, because nobody would use them in production anyway.  For
  this reason, we decided to make CONFIG_PM_SLEEP select
  CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
  became redundant and CONFIG_PM could be used instead of it.  The
  material here makes that replacement in a major part of the tree, but
  there will be at least one more batch of that in the second part of
  the merge window.

  Specifics:

   - Support for retrieving device properties information from ACPI _DSD
     device configuration objects and a unified device properties
     interface for device drivers (and subsystems) on top of that.  As
     stated above, this works with Device Trees and ACPI and allows
     device drivers to be written in a platform firmware (DT or ACPI)
     agnostic way.  The at25, leds-gpio and gpio_keys_polled drivers are
     now going to use this new interface and the GPIO subsystem is
     additionally modified to allow device drivers to assign names to
     GPIO resources returned by ACPI _CRS objects (in case _DSD is not
     present or does not provide the expected data).  The changes in
     this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
     Lu, and Darren Hart with some fixes from others (Fabio Estevam,
     Geert Uytterhoeven).

   - Support for Hardware Managed Performance States (HWP) as described
     in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
     driver.  CPUID is used to detect whether or not the feature is
     supported by the processor.  If supported, it will be enabled
     automatically unless the intel_pstate=no_hwp switch is present in
     the kernel command line.  From Dirk Brandewie.

   - New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).

   - Support for firmware interface based on ACPI operation regions used
     by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
     platforms for power resource control and thermal management (Aaron
     Lu).

   - Limited support for retrieving off-the-hierarchy dependencies
     between devices from ACPI _DEP device configuration objects and
     deferred probing support for the ACPI battery driver based on the
     _DEP information to make that driver work on Asus T100A (Lan
     Tianyu).

   - New cpufreq driver for the Loongson1B processor (Kelvin Cheung).

   - ACPICA update to upstream revision 20141107 which only affects
     tools (Bob Moore).

   - Fixes for race conditions in the ACPICA's interrupt handling code
     and in the ACPI code related to system suspend and resume (Lv Zheng
     and Rafael J Wysocki).

   - ACPI core fix for an RCU-related issue in the ioremap() regions
     management code that slowed down significantly after CPUs had been
     allowed to enter idle states even if they'd had RCU callbakcs
     queued and triggered some problems in certain proprietary graphics
     driver (and elsewhere).  The fix replaces synchronize_rcu() in that
     code with synchronize_rcu_expedited() which makes the issue go
     away.  From Konstantin Khlebnikov.

   - ACPI LPSS (Low-Power Subsystem) driver fix to handle power
     management of the DMA engine included into the LPSS correctly.  The
     problem is that the DMA engine doesn't have ACPI PM support of its
     own and it simply is turned off when the last LPSS device having
     ACPI PM support goes into D3cold.  To work around that, the PM
     domain used by the ACPI LPSS driver is redesigned so at least one
     device with ACPI PM support will be on as long as the DMA engine is
     in use.  From Andy Shevchenko.

   - ACPI backlight driver fix to avoid using it on "Win8-compatible"
     systems where it doesn't work and where it was used by default by
     mistake (Aaron Lu).

   - Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
     Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
     Chaugule (mostly related to the upcoming ARM64 support).

   - Intel RAPL (Running Average Power Limit) power capping driver fixes
     and improvements including new processor IDs (Jacob Pan).

   - Generic power domains modification to power up domains after
     attaching devices to them to meet the expectations of device
     drivers and bus types assuming devices to be accessible at probe
     time (Ulf Hansson).

   - Preliminary support for controlling device clocks from the generic
     power domains core code and modifications of the ARM/shmobile
     platform to use that feature (Ulf Hansson).

   - Assorted minor fixes and cleanups of the generic power domains core
     code (Ulf Hansson, Geert Uytterhoeven).

   - Assorted minor fixes and cleanups of the device clocks control code
     in the PM core (Geert Uytterhoeven, Grygorii Strashko).

   - Consolidation of device power management Kconfig options by making
     CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
     which is now redundant (Rafael J Wysocki and Kevin Hilman).  That
     is the first batch of the changes needed for this purpose.

   - Core device runtime power management support code cleanup related
     to the execution of callbacks (Andrzej Hajda).

   - cpuidle ARM support improvements (Lorenzo Pieralisi).

   - cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
     new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
     Bartlomiej Zolnierkiewicz).

   - New cpufreq driver callback (->ready) to be executed when the
     cpufreq core is ready to use a given policy object and cpufreq-dt
     driver modification to use that callback for cooling device
     registration (Viresh Kumar).

   - cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
     Geboski, Tomeu Vizoso).

   - Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
     cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
     Stefan Wahren, Petr Cvek).

   - OPP (Operating Performance Points) framework modification to allow
     OPPs to be removed too and update of a few cpufreq drivers
     (cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
     during initialization) on driver removal (Viresh Kumar).

   - Hibernation core fixes and cleanups (Tina Ruchandani and Markus
     Elfring).

   - PM Kconfig fix related to CPU power management (Pankaj Dubey).

   - cpupower tool fix (Prarit Bhargava)"

* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
  i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
  dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  tools: cpupower: fix return checks for sysfs_get_idlestate_count()
  drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
  MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  leds: leds-gpio: Fix multiple instances registration without 'label' property
  iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
  block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
  PM: Merge the SET*_RUNTIME_PM_OPS() macros
  ...

26 files changed, 1878 insertions, 108 deletions

diff --git a/drivers/acpi/Kconfig b/drivers/acpi/Kconfig
index b23fe37f67c0..8951cefb0a96 100644
--- a/drivers/acpi/Kconfig
+++ b/drivers/acpi/Kconfig
@@ -360,15 +360,14 @@ config ACPI_BGRT
 config ACPI_REDUCED_HARDWARE_ONLY
 	bool "Hardware-reduced ACPI support only" if EXPERT
 	def_bool n
-	depends on ACPI
 	help
-	This config item changes the way the ACPI code is built.  When this
-	option is selected, the kernel will use a specialized version of
-	ACPICA that ONLY supports the ACPI "reduced hardware" mode.  The
-	resulting kernel will be smaller but it will also be restricted to
-	running in ACPI reduced hardware mode ONLY.
+	  This config item changes the way the ACPI code is built.  When this
+	  option is selected, the kernel will use a specialized version of
+	  ACPICA that ONLY supports the ACPI "reduced hardware" mode.  The
+	  resulting kernel will be smaller but it will also be restricted to
+	  running in ACPI reduced hardware mode ONLY.
 
-	If you are unsure what to do, do not enable this option.
+	  If you are unsure what to do, do not enable this option.
 
 source "drivers/acpi/apei/Kconfig"
 
@@ -394,4 +393,27 @@ config ACPI_EXTLOG
 	  driver adds support for that functionality with corresponding
 	  tracepoint which carries that information to userspace.
 
+menuconfig PMIC_OPREGION
+	bool "PMIC (Power Management Integrated Circuit) operation region support"
+	help
+	  Select this option to enable support for ACPI operation
+	  region of the PMIC chip. The operation region can be used
+	  to control power rails and sensor reading/writing on the
+	  PMIC chip.
+
+if PMIC_OPREGION
+config CRC_PMIC_OPREGION
+	bool "ACPI operation region support for CrystalCove PMIC"
+	depends on INTEL_SOC_PMIC
+	help
+	  This config adds ACPI operation region support for CrystalCove PMIC.
+
+config XPOWER_PMIC_OPREGION
+	bool "ACPI operation region support for XPower AXP288 PMIC"
+	depends on AXP288_ADC = y
+	help
+	  This config adds ACPI operation region support for XPower AXP288 PMIC.
+
+endif
+
 endif	# ACPI
diff --git a/drivers/acpi/Makefile b/drivers/acpi/Makefile
index c3b2fcb729f3..f74317cc1ca9 100644
--- a/drivers/acpi/Makefile
+++ b/drivers/acpi/Makefile
@@ -47,6 +47,7 @@ acpi-y				+= int340x_thermal.o
 acpi-y				+= power.o
 acpi-y				+= event.o
 acpi-y				+= sysfs.o
+acpi-y				+= property.o
 acpi-$(CONFIG_X86)		+= acpi_cmos_rtc.o
 acpi-$(CONFIG_DEBUG_FS)		+= debugfs.o
 acpi-$(CONFIG_ACPI_NUMA)	+= numa.o
@@ -87,3 +88,7 @@ obj-$(CONFIG_ACPI_PROCESSOR_AGGREGATOR) += acpi_pad.o
 obj-$(CONFIG_ACPI_APEI)		+= apei/
 
 obj-$(CONFIG_ACPI_EXTLOG)	+= acpi_extlog.o
+
+obj-$(CONFIG_PMIC_OPREGION)	+= pmic/intel_pmic.o
+obj-$(CONFIG_CRC_PMIC_OPREGION) += pmic/intel_pmic_crc.o
+obj-$(CONFIG_XPOWER_PMIC_OPREGION) += pmic/intel_pmic_xpower.o
diff --git a/drivers/acpi/acpi_lpss.c b/drivers/acpi/acpi_lpss.c
index 93d160661f4c..4f3febf8a589 100644
--- a/drivers/acpi/acpi_lpss.c
+++ b/drivers/acpi/acpi_lpss.c
@@ -1,7 +1,7 @@
 /*
  * ACPI support for Intel Lynxpoint LPSS.
  *
- * Copyright (C) 2013, Intel Corporation
+ * Copyright (C) 2013, 2014, Intel Corporation
  * Authors: Mika Westerberg <mika.westerberg@linux.intel.com>
  *          Rafael J. Wysocki <rafael.j.wysocki@intel.com>
  *
@@ -60,6 +60,8 @@ ACPI_MODULE_NAME("acpi_lpss");
 #define LPSS_CLK_DIVIDER		BIT(2)
 #define LPSS_LTR			BIT(3)
 #define LPSS_SAVE_CTX			BIT(4)
+#define LPSS_DEV_PROXY			BIT(5)
+#define LPSS_PROXY_REQ			BIT(6)
 
 struct lpss_private_data;
 
@@ -70,8 +72,10 @@ struct lpss_device_desc {
 	void (*setup)(struct lpss_private_data *pdata);
 };
 
+static struct device *proxy_device;
+
 static struct lpss_device_desc lpss_dma_desc = {
-	.flags = LPSS_CLK,
+	.flags = LPSS_CLK | LPSS_PROXY_REQ,
 };
 
 struct lpss_private_data {
@@ -146,22 +150,24 @@ static struct lpss_device_desc byt_pwm_dev_desc = {
 };
 
 static struct lpss_device_desc byt_uart_dev_desc = {
-	.flags = LPSS_CLK | LPSS_CLK_GATE | LPSS_CLK_DIVIDER | LPSS_SAVE_CTX,
+	.flags = LPSS_CLK | LPSS_CLK_GATE | LPSS_CLK_DIVIDER | LPSS_SAVE_CTX |
+		 LPSS_DEV_PROXY,
 	.prv_offset = 0x800,
 	.setup = lpss_uart_setup,
 };
 
 static struct lpss_device_desc byt_spi_dev_desc = {
-	.flags = LPSS_CLK | LPSS_CLK_GATE | LPSS_CLK_DIVIDER | LPSS_SAVE_CTX,
+	.flags = LPSS_CLK | LPSS_CLK_GATE | LPSS_CLK_DIVIDER | LPSS_SAVE_CTX |
+		 LPSS_DEV_PROXY,
 	.prv_offset = 0x400,
 };
 
 static struct lpss_device_desc byt_sdio_dev_desc = {
-	.flags = LPSS_CLK,
+	.flags = LPSS_CLK | LPSS_DEV_PROXY,
 };
 
 static struct lpss_device_desc byt_i2c_dev_desc = {
-	.flags = LPSS_CLK | LPSS_SAVE_CTX,
+	.flags = LPSS_CLK | LPSS_SAVE_CTX | LPSS_DEV_PROXY,
 	.prv_offset = 0x800,
 	.setup = byt_i2c_setup,
 };
@@ -368,6 +374,8 @@ static int acpi_lpss_create_device(struct acpi_device *adev,
 	adev->driver_data = pdata;
 	pdev = acpi_create_platform_device(adev);
 	if (!IS_ERR_OR_NULL(pdev)) {
+		if (!proxy_device && dev_desc->flags & LPSS_DEV_PROXY)
+			proxy_device = &pdev->dev;
 		return 1;
 	}
 
@@ -499,14 +507,15 @@ static void acpi_lpss_set_ltr(struct device *dev, s32 val)
 /**
  * acpi_lpss_save_ctx() - Save the private registers of LPSS device
  * @dev: LPSS device
+ * @pdata: pointer to the private data of the LPSS device
  *
  * Most LPSS devices have private registers which may loose their context when
  * the device is powered down. acpi_lpss_save_ctx() saves those registers into
  * prv_reg_ctx array.
  */
-static void acpi_lpss_save_ctx(struct device *dev)
+static void acpi_lpss_save_ctx(struct device *dev,
+			       struct lpss_private_data *pdata)
 {
-	struct lpss_private_data *pdata = acpi_driver_data(ACPI_COMPANION(dev));
 	unsigned int i;
 
 	for (i = 0; i < LPSS_PRV_REG_COUNT; i++) {
@@ -521,12 +530,13 @@ static void acpi_lpss_save_ctx(struct device *dev)
 /**
  * acpi_lpss_restore_ctx() - Restore the private registers of LPSS device
  * @dev: LPSS device
+ * @pdata: pointer to the private data of the LPSS device
  *
  * Restores the registers that were previously stored with acpi_lpss_save_ctx().
  */
-static void acpi_lpss_restore_ctx(struct device *dev)
+static void acpi_lpss_restore_ctx(struct device *dev,
+				  struct lpss_private_data *pdata)
 {
-	struct lpss_private_data *pdata = acpi_driver_data(ACPI_COMPANION(dev));
 	unsigned int i;
 
 	/*
@@ -549,54 +559,82 @@ static void acpi_lpss_restore_ctx(struct device *dev)
 #ifdef CONFIG_PM_SLEEP
 static int acpi_lpss_suspend_late(struct device *dev)
 {
-	int ret = pm_generic_suspend_late(dev);
+	struct lpss_private_data *pdata = acpi_driver_data(ACPI_COMPANION(dev));
+	int ret;
 
+	ret = pm_generic_suspend_late(dev);
 	if (ret)
 		return ret;
 
-	acpi_lpss_save_ctx(dev);
+	if (pdata->dev_desc->flags & LPSS_SAVE_CTX)
+		acpi_lpss_save_ctx(dev, pdata);
+
 	return acpi_dev_suspend_late(dev);
 }
 
 static int acpi_lpss_resume_early(struct device *dev)
 {
-	int ret = acpi_dev_resume_early(dev);
+	struct lpss_private_data *pdata = acpi_driver_data(ACPI_COMPANION(dev));
+	int ret;
 
+	ret = acpi_dev_resume_early(dev);
 	if (ret)
 		return ret;
 
-	acpi_lpss_restore_ctx(dev);
+	if (pdata->dev_desc->flags & LPSS_SAVE_CTX)
+		acpi_lpss_restore_ctx(dev, pdata);
+
 	return pm_generic_resume_early(dev);
 }
 #endif /* CONFIG_PM_SLEEP */
 
-#ifdef CONFIG_PM_RUNTIME
 static int acpi_lpss_runtime_suspend(struct device *dev)
 {
-	int ret = pm_generic_runtime_suspend(dev);
+	struct lpss_private_data *pdata = acpi_driver_data(ACPI_COMPANION(dev));
+	int ret;
+
+	ret = pm_generic_runtime_suspend(dev);
+	if (ret)
+		return ret;
 
+	if (pdata->dev_desc->flags & LPSS_SAVE_CTX)
+		acpi_lpss_save_ctx(dev, pdata);
+
+	ret = acpi_dev_runtime_suspend(dev);
 	if (ret)
 		return ret;
 
-	acpi_lpss_save_ctx(dev);
-	return acpi_dev_runtime_suspend(dev);
+	if (pdata->dev_desc->flags & LPSS_PROXY_REQ && proxy_device)
+		return pm_runtime_put_sync_suspend(proxy_device);
+
+	return 0;
 }
 
 static int acpi_lpss_runtime_resume(struct device *dev)
 {
-	int ret = acpi_dev_runtime_resume(dev);
+	struct lpss_private_data *pdata = acpi_driver_data(ACPI_COMPANION(dev));
+	int ret;
+
+	if (pdata->dev_desc->flags & LPSS_PROXY_REQ && proxy_device) {
+		ret = pm_runtime_get_sync(proxy_device);
+		if (ret)
+			return ret;
+	}
 
+	ret = acpi_dev_runtime_resume(dev);
 	if (ret)
 		return ret;
 
-	acpi_lpss_restore_ctx(dev);
+	if (pdata->dev_desc->flags & LPSS_SAVE_CTX)
+		acpi_lpss_restore_ctx(dev, pdata);
+
 	return pm_generic_runtime_resume(dev);
 }
-#endif /* CONFIG_PM_RUNTIME */
 #endif /* CONFIG_PM */
 
 static struct dev_pm_domain acpi_lpss_pm_domain = {
 	.ops = {
+#ifdef CONFIG_PM
 #ifdef CONFIG_PM_SLEEP
 		.prepare = acpi_subsys_prepare,
 		.complete = acpi_subsys_complete,
@@ -608,7 +646,6 @@ static struct dev_pm_domain acpi_lpss_pm_domain = {
 		.poweroff_late = acpi_lpss_suspend_late,
 		.restore_early = acpi_lpss_resume_early,
 #endif
-#ifdef CONFIG_PM_RUNTIME
 		.runtime_suspend = acpi_lpss_runtime_suspend,
 		.runtime_resume = acpi_lpss_runtime_resume,
 #endif
@@ -631,30 +668,27 @@ static int acpi_lpss_platform_notify(struct notifier_block *nb,
 		return 0;
 
 	pdata = acpi_driver_data(adev);
-	if (!pdata || !pdata->mmio_base)
+	if (!pdata)
 		return 0;
 
-	if (pdata->mmio_size < pdata->dev_desc->prv_offset + LPSS_LTR_SIZE) {
+	if (pdata->mmio_base &&
+	    pdata->mmio_size < pdata->dev_desc->prv_offset + LPSS_LTR_SIZE) {
 		dev_err(&pdev->dev, "MMIO size insufficient to access LTR\n");
 		return 0;
 	}
 
 	switch (action) {
-	case BUS_NOTIFY_BOUND_DRIVER:
-		if (pdata->dev_desc->flags & LPSS_SAVE_CTX)
-			pdev->dev.pm_domain = &acpi_lpss_pm_domain;
-		break;
-	case BUS_NOTIFY_UNBOUND_DRIVER:
-		if (pdata->dev_desc->flags & LPSS_SAVE_CTX)
-			pdev->dev.pm_domain = NULL;
-		break;
 	case BUS_NOTIFY_ADD_DEVICE:
+		pdev->dev.pm_domain = &acpi_lpss_pm_domain;
 		if (pdata->dev_desc->flags & LPSS_LTR)
 			return sysfs_create_group(&pdev->dev.kobj,
 						  &lpss_attr_group);
+		break;
 	case BUS_NOTIFY_DEL_DEVICE:
 		if (pdata->dev_desc->flags & LPSS_LTR)
 			sysfs_remove_group(&pdev->dev.kobj, &lpss_attr_group);
+		pdev->dev.pm_domain = NULL;
+		break;
 	default:
 		break;
 	}
diff --git a/drivers/acpi/acpica/acglobal.h b/drivers/acpi/acpica/acglobal.h
index ebf02cc10a43..7f60582d0c8c 100644
--- a/drivers/acpi/acpica/acglobal.h
+++ b/drivers/acpi/acpica/acglobal.h
@@ -305,6 +305,7 @@ ACPI_INIT_GLOBAL(u8, acpi_gbl_db_output_flags, ACPI_DB_CONSOLE_OUTPUT);
 
 ACPI_INIT_GLOBAL(u8, acpi_gbl_no_resource_disassembly, FALSE);
 ACPI_INIT_GLOBAL(u8, acpi_gbl_ignore_noop_operator, FALSE);
+ACPI_INIT_GLOBAL(u8, acpi_gbl_cstyle_disassembly, TRUE);
 
 ACPI_GLOBAL(u8, acpi_gbl_db_opt_disasm);
 ACPI_GLOBAL(u8, acpi_gbl_db_opt_verbose);
diff --git a/drivers/acpi/acpica/aclocal.h b/drivers/acpi/acpica/aclocal.h
index c00e7e41ad75..680d23bbae7c 100644
--- a/drivers/acpi/acpica/aclocal.h
+++ b/drivers/acpi/acpica/aclocal.h
@@ -454,6 +454,7 @@ struct acpi_gpe_register_info {
 	u16 base_gpe_number;	/* Base GPE number for this register */
 	u8 enable_for_wake;	/* GPEs to keep enabled when sleeping */
 	u8 enable_for_run;	/* GPEs to keep enabled when running */
+	u8 enable_mask;		/* Current mask of enabled GPEs */
 };
 
 /*
@@ -722,6 +723,7 @@ union acpi_parse_value {
 	ACPI_DISASM_ONLY_MEMBERS (\
 	u8                              disasm_flags;   /* Used during AML disassembly */\
 	u8                              disasm_opcode;  /* Subtype used for disassembly */\
+	char                            *operator_symbol;/* Used for C-style operator name strings */\
 	char                            aml_op_name[16])	/* Op name (debug only) */
 
 /* Flags for disasm_flags field above */
@@ -827,6 +829,8 @@ struct acpi_parse_state {
 #define ACPI_PARSEOP_EMPTY_TERMLIST     0x04
 #define ACPI_PARSEOP_PREDEF_CHECKED     0x08
 #define ACPI_PARSEOP_SPECIAL            0x10
+#define ACPI_PARSEOP_COMPOUND           0x20
+#define ACPI_PARSEOP_ASSIGNMENT         0x40
 
 /*****************************************************************************
  *
diff --git a/drivers/acpi/acpica/evgpe.c b/drivers/acpi/acpica/evgpe.c
index 2095dfb72bcb..aa70154cf4fa 100644
--- a/drivers/acpi/acpica/evgpe.c
+++ b/drivers/acpi/acpica/evgpe.c
@@ -134,7 +134,7 @@ acpi_status acpi_ev_enable_gpe(struct acpi_gpe_event_info *gpe_event_info)
 
 	/* Enable the requested GPE */
 
-	status = acpi_hw_low_set_gpe(gpe_event_info, ACPI_GPE_ENABLE);
+	status = acpi_hw_low_set_gpe(gpe_event_info, ACPI_GPE_ENABLE_SAVE);
 	return_ACPI_STATUS(status);
 }
 
@@ -213,7 +213,7 @@ acpi_ev_remove_gpe_reference(struct acpi_gpe_event_info *gpe_event_info)
 		if (ACPI_SUCCESS(status)) {
 			status =
 			    acpi_hw_low_set_gpe(gpe_event_info,
-						ACPI_GPE_DISABLE);
+						ACPI_GPE_DISABLE_SAVE);
 		}
 
 		if (ACPI_FAILURE(status)) {
@@ -616,8 +616,11 @@ static void ACPI_SYSTEM_XFACE acpi_ev_asynch_execute_gpe_method(void *context)
 static void ACPI_SYSTEM_XFACE acpi_ev_asynch_enable_gpe(void *context)
 {
 	struct acpi_gpe_event_info *gpe_event_info = context;
+	acpi_cpu_flags flags;
 
+	flags = acpi_os_acquire_lock(acpi_gbl_gpe_lock);
 	(void)acpi_ev_finish_gpe(gpe_event_info);
+	acpi_os_release_lock(acpi_gbl_gpe_lock, flags);
 
 	ACPI_FREE(gpe_event_info);
 	return;
@@ -655,7 +658,7 @@ acpi_status acpi_ev_finish_gpe(struct acpi_gpe_event_info * gpe_event_info)
 
 	/*
 	 * Enable this GPE, conditionally. This means that the GPE will
-	 * only be physically enabled if the enable_for_run bit is set
+	 * only be physically enabled if the enable_mask bit is set
 	 * in the event_info.
 	 */
 	(void)acpi_hw_low_set_gpe(gpe_event_info, ACPI_GPE_CONDITIONAL_ENABLE);
diff --git a/drivers/acpi/acpica/hwgpe.c b/drivers/acpi/acpica/hwgpe.c
index 48ac7b7b59cd..494027f5c067 100644
--- a/drivers/acpi/acpica/hwgpe.c
+++ b/drivers/acpi/acpica/hwgpe.c
@@ -115,12 +115,12 @@ acpi_hw_low_set_gpe(struct acpi_gpe_event_info *gpe_event_info, u32 action)
 	/* Set or clear just the bit that corresponds to this GPE */
 
 	register_bit = acpi_hw_get_gpe_register_bit(gpe_event_info);
-	switch (action) {
+	switch (action & ~ACPI_GPE_SAVE_MASK) {
 	case ACPI_GPE_CONDITIONAL_ENABLE:
 
-		/* Only enable if the enable_for_run bit is set */
+		/* Only enable if the corresponding enable_mask bit is set */
 
-		if (!(register_bit & gpe_register_info->enable_for_run)) {
+		if (!(register_bit & gpe_register_info->enable_mask)) {
 			return (AE_BAD_PARAMETER);
 		}
 
@@ -145,6 +145,9 @@ acpi_hw_low_set_gpe(struct acpi_gpe_event_info *gpe_event_info, u32 action)
 	/* Write the updated enable mask */
 
 	status = acpi_hw_write(enable_mask, &gpe_register_info->enable_address);
+	if (ACPI_SUCCESS(status) && (action & ACPI_GPE_SAVE_MASK)) {
+		gpe_register_info->enable_mask = enable_mask;
+	}
 	return (status);
 }
 
@@ -262,6 +265,32 @@ acpi_hw_get_gpe_status(struct acpi_gpe_event_info * gpe_event_info,
 
 /******************************************************************************
  *
+ * FUNCTION:    acpi_hw_gpe_enable_write
+ *
+ * PARAMETERS:  enable_mask         - Bit mask to write to the GPE register
+ *              gpe_register_info   - Gpe Register info
+ *
+ * RETURN:      Status
+ *
+ * DESCRIPTION: Write the enable mask byte to the given GPE register.
+ *
+ ******************************************************************************/
+
+static acpi_status
+acpi_hw_gpe_enable_write(u8 enable_mask,
+			 struct acpi_gpe_register_info *gpe_register_info)
+{
+	acpi_status status;
+
+	status = acpi_hw_write(enable_mask, &gpe_register_info->enable_address);
+	if (ACPI_SUCCESS(status)) {
+		gpe_register_info->enable_mask = enable_mask;
+	}
+	return (status);
+}
+
+/******************************************************************************
+ *
  * FUNCTION:    acpi_hw_disable_gpe_block
  *
  * PARAMETERS:  gpe_xrupt_info      - GPE Interrupt info
@@ -287,8 +316,8 @@ acpi_hw_disable_gpe_block(struct acpi_gpe_xrupt_info *gpe_xrupt_info,
 		/* Disable all GPEs in this register */
 
 		status =
-		    acpi_hw_write(0x00,
-				  &gpe_block->register_info[i].enable_address);
+		    acpi_hw_gpe_enable_write(0x00,
+					     &gpe_block->register_info[i]);
 		if (ACPI_FAILURE(status)) {
 			return (status);
 		}
@@ -355,21 +384,23 @@ acpi_hw_enable_runtime_gpe_block(struct acpi_gpe_xrupt_info *gpe_xrupt_info,
 {
 	u32 i;
 	acpi_status status;
+	struct acpi_gpe_register_info *gpe_register_info;
 
 	/* NOTE: assumes that all GPEs are currently disabled */
 
 	/* Examine each GPE Register within the block */
 
 	for (i = 0; i < gpe_block->register_count; i++) {
-		if (!gpe_block->register_info[i].enable_for_run) {
+		gpe_register_info = &gpe_block->register_info[i];
+		if (!gpe_register_info->enable_for_run) {
 			continue;
 		}
 
 		/* Enable all "runtime" GPEs in this register */
 
 		status =
-		    acpi_hw_write(gpe_block->register_info[i].enable_for_run,
-				  &gpe_block->register_info[i].enable_address);
+		    acpi_hw_gpe_enable_write(gpe_register_info->enable_for_run,
+					     gpe_register_info);
 		if (ACPI_FAILURE(status)) {
 			return (status);
 		}
@@ -399,10 +430,12 @@ acpi_hw_enable_wakeup_gpe_block(struct acpi_gpe_xrupt_info *gpe_xrupt_info,
 {
 	u32 i;
 	acpi_status status;
+	struct acpi_gpe_register_info *gpe_register_info;
 
 	/* Examine each GPE Register within the block */
 
 	for (i = 0; i < gpe_block->register_count; i++) {
+		gpe_register_info = &gpe_block->register_info[i];
 
 		/*
 		 * Enable all "wake" GPEs in this register and disable the
@@ -410,8 +443,8 @@ acpi_hw_enable_wakeup_gpe_block(struct acpi_gpe_xrupt_info *gpe_xrupt_info,
 		 */
 
 		status =
-		    acpi_hw_write(gpe_block->register_info[i].enable_for_wake,
-				  &gpe_block->register_info[i].enable_address);
+		    acpi_hw_gpe_enable_write(gpe_register_info->enable_for_wake,
+					     gpe_register_info);
 		if (ACPI_FAILURE(status)) {
 			return (status);
 		}
diff --git a/drivers/acpi/acpica/utresrc.c b/drivers/acpi/acpica/utresrc.c
index 5cd017c7ac0e..bc1ff820c7dd 100644
--- a/drivers/acpi/acpica/utresrc.c
+++ b/drivers/acpi/acpica/utresrc.c
@@ -263,7 +263,7 @@ const char *acpi_gbl_bpb_decode[] = {
 /* UART serial bus stop bits */
 
 const char *acpi_gbl_sb_decode[] = {
-	"StopBitsNone",
+	"StopBitsZero",
 	"StopBitsOne",
 	"StopBitsOnePlusHalf",
 	"StopBitsTwo"
diff --git a/drivers/acpi/acpica/utxface.c b/drivers/acpi/acpica/utxface.c
index 502a8492dc83..49c873c68756 100644
--- a/drivers/acpi/acpica/utxface.c
+++ b/drivers/acpi/acpica/utxface.c
@@ -531,7 +531,9 @@ acpi_decode_pld_buffer(u8 *in_buffer,
 	ACPI_MOVE_32_TO_32(&dword, &buffer[0]);
 	pld_info->revision = ACPI_PLD_GET_REVISION(&dword);
 	pld_info->ignore_color = ACPI_PLD_GET_IGNORE_COLOR(&dword);
-	pld_info->color = ACPI_PLD_GET_COLOR(&dword);
+	pld_info->red = ACPI_PLD_GET_RED(&dword);
+	pld_info->green = ACPI_PLD_GET_GREEN(&dword);
+	pld_info->blue = ACPI_PLD_GET_BLUE(&dword);
 
 	/* Second 32-bit DWord */
 
diff --git a/drivers/acpi/acpica/utxfinit.c b/drivers/acpi/acpica/utxfinit.c
index 13380d818462..b1fd6886e439 100644
--- a/drivers/acpi/acpica/utxfinit.c
+++ b/drivers/acpi/acpica/utxfinit.c
@@ -53,6 +53,9 @@
 #define _COMPONENT          ACPI_UTILITIES
 ACPI_MODULE_NAME("utxfinit")
 
+/* For acpi_exec only */
+void ae_do_object_overrides(void);
+
 /*******************************************************************************
  *
  * FUNCTION:    acpi_initialize_subsystem
@@ -65,6 +68,7 @@ ACPI_MODULE_NAME("utxfinit")
  *              called, so any early initialization belongs here.
  *
  ******************************************************************************/
+
 acpi_status __init acpi_initialize_subsystem(void)
 {
 	acpi_status status;
@@ -275,6 +279,13 @@ acpi_status __init acpi_initialize_objects(u32 flags)
 			return_ACPI_STATUS(status);
 		}
 	}
+#ifdef ACPI_EXEC_APP
+	/*
+	 * This call implements the "initialization file" option for acpi_exec.
+	 * This is the precise point that we want to perform the overrides.
+	 */
+	ae_do_object_overrides();
+#endif
 
 	/*
 	 * Execute any module-level code that was detected during the table load
diff --git a/drivers/acpi/battery.c b/drivers/acpi/battery.c
index 8ec8a89a20ab..d98ba4355819 100644
--- a/drivers/acpi/battery.c
+++ b/drivers/acpi/battery.c
@@ -1180,6 +1180,10 @@ static int acpi_battery_add(struct acpi_device *device)
 
 	if (!device)
 		return -EINVAL;
+
+	if (device->dep_unmet)
+		return -EPROBE_DEFER;
+
 	battery = kzalloc(sizeof(struct acpi_battery), GFP_KERNEL);
 	if (!battery)
 		return -ENOMEM;
diff --git a/drivers/acpi/device_pm.c b/drivers/acpi/device_pm.c
index 7db193160766..897640188acd 100644
--- a/drivers/acpi/device_pm.c
+++ b/drivers/acpi/device_pm.c
@@ -201,7 +201,7 @@ int acpi_device_set_power(struct acpi_device *device, int state)
 	 * Transition Power
 	 * ----------------
 	 * In accordance with the ACPI specification first apply power (via
-	 * power resources) and then evalute _PSx.
+	 * power resources) and then evaluate _PSx.
 	 */
 	if (device->power.flags.power_resources) {
 		result = acpi_power_transition(device, state);
@@ -692,7 +692,6 @@ static int acpi_device_wakeup(struct acpi_device *adev, u32 target_state,
 	return 0;
 }
 
-#ifdef CONFIG_PM_RUNTIME
 /**
  * acpi_pm_device_run_wake - Enable/disable remote wakeup for given device.
  * @dev: Device to enable/disable the platform to wake up.