Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC multiplatform conversion patches from Olof Johansson:
 "Here are more patches in the progression towards multiplatform, sparse
  irq conversions in particular.

  Tegra has a handful of cleanups and general groundwork, but is not
  quite there yet on full enablement.

  Platforms that are enabled through this branch are VT8500 and Zynq.
  Note that i.MX was converted in one of the earlier cleanup branches as
  well (before we started a separate topic for multiplatform).  And both
  new platforms for this merge window, sunxi and bcm, were merged with
  multiplatform support enabled."

Fix up conflicts mostly as per Olof.

* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
  ARM: zynq: Remove all unused mach headers
  ARM: zynq: add support for ARCH_MULTIPLATFORM
  ARM: zynq: make use of debug_ll_io_init()
  ARM: zynq: remove TTC early mapping
  ARM: tegra: move debug-macro.S to include/debug
  ARM: tegra: don't include iomap.h from debug-macro.S
  ARM: tegra: decouple uncompress.h and debug-macro.S
  ARM: tegra: simplify DEBUG_LL UART selection options
  ARM: tegra: select SPARSE_IRQ
  ARM: tegra: enhance timer.c to get IO address from device tree
  ARM: tegra: enhance timer.c to get IRQ info from device tree
  ARM: timer: fix checkpatch warnings
  ARM: tegra: add TWD to device tree
  ARM: tegra: define DT bindings for and instantiate RTC
  ARM: tegra: define DT bindings for and instantiate timer
  clocksource/mtu-nomadik: use apb_pclk
  clk: ux500: Register mtu apb_pclocks
  ARM: plat-nomadik: convert platforms to SPARSE_IRQ
  mfd/db8500-prcmu: use the irq_domain_add_simple()
  mfd/ab8500-core: use irq_domain_add_simple()
  ...

52 files changed, 534 insertions, 1282 deletions

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 3bb60c8adbff..2277f9530b00 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -650,6 +650,7 @@ config ARCH_TEGRA
 	select HAVE_CLK
 	select HAVE_SMP
 	select MIGHT_HAVE_CACHE_L2X0
+	select SPARSE_IRQ
 	select USE_OF
 	help
 	  This enables support for NVIDIA Tegra based systems (Tegra APX,
@@ -891,6 +892,7 @@ config ARCH_U8500
 	select GENERIC_CLOCKEVENTS
 	select HAVE_SMP
 	select MIGHT_HAVE_CACHE_L2X0
+	select SPARSE_IRQ
 	help
 	  Support for ST-Ericsson's Ux500 architecture
 
@@ -905,6 +907,7 @@ config ARCH_NOMADIK
 	select MIGHT_HAVE_CACHE_L2X0
 	select PINCTRL
 	select PINCTRL_STN8815
+	select SPARSE_IRQ
 	help
 	  Support for the Nomadik platform by ST-Ericsson
 
@@ -948,7 +951,7 @@ config ARCH_OMAP
 	help
 	  Support for TI's OMAP platform (OMAP1/2/3/4).
 
-config ARCH_VT8500
+config ARCH_VT8500_SINGLE
 	bool "VIA/WonderMedia 85xx"
 	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
@@ -958,22 +961,12 @@ config ARCH_VT8500
 	select GENERIC_CLOCKEVENTS
 	select GENERIC_GPIO
 	select HAVE_CLK
+	select MULTI_IRQ_HANDLER
+	select SPARSE_IRQ
 	select USE_OF
 	help
 	  Support for VIA/WonderMedia VT8500/WM85xx System-on-Chip.
 
-config ARCH_ZYNQ
-	bool "Xilinx Zynq ARM Cortex A9 Platform"
-	select ARM_AMBA
-	select ARM_GIC
-	select COMMON_CLK
-	select CPU_V7
-	select GENERIC_CLOCKEVENTS
-	select ICST
-	select MIGHT_HAVE_CACHE_L2X0
-	select USE_OF
-	help
-	  Support for Xilinx Zynq ARM Cortex A9 Platform
 endchoice
 
 menu "Multiple platform selection"
@@ -1074,7 +1067,6 @@ source "arch/arm/mach-mxs/Kconfig"
 source "arch/arm/mach-netx/Kconfig"
 
 source "arch/arm/mach-nomadik/Kconfig"
-source "arch/arm/plat-nomadik/Kconfig"
 
 source "arch/arm/plat-omap/Kconfig"
 
@@ -1137,8 +1129,12 @@ source "arch/arm/mach-versatile/Kconfig"
 source "arch/arm/mach-vexpress/Kconfig"
 source "arch/arm/plat-versatile/Kconfig"
 
+source "arch/arm/mach-vt8500/Kconfig"
+
 source "arch/arm/mach-w90x900/Kconfig"
 
+source "arch/arm/mach-zynq/Kconfig"
+
 # Definitions to make life easier
 config ARCH_ACORN
 	bool
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 512b39438548..661030d6bc6c 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -379,6 +379,13 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on Allwinner A1X based platforms on the UART1.
 
+	config DEBUG_TEGRA_UART
+		depends on ARCH_TEGRA
+		bool "Use Tegra UART for low-level debug"
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on Tegra based platforms.
+
 	config DEBUG_VEXPRESS_UART0_DETECT
 		bool "Autodetect UART0 on Versatile Express Cortex-A core tiles"
 		depends on ARCH_VEXPRESS && CPU_CP15_MMU
@@ -452,6 +459,36 @@ config DEBUG_IMX6Q_UART_PORT
 	  Choose UART port on which kernel low-level debug messages
 	  should be output.
 
+choice
+	prompt "Low-level debug console UART"
+	depends on DEBUG_LL && DEBUG_TEGRA_UART
+
+	config TEGRA_DEBUG_UART_AUTO_ODMDATA
+	bool "Via ODMDATA"
+	help
+	  Automatically determines which UART to use for low-level debug based
+	  on the ODMDATA value. This value is part of the BCT, and is written
+	  to the boot memory device using nvflash, or other flashing tool.
+	  When bits 19:18 are 3, then bits 17:15 indicate which UART to use;
+	  0/1/2/3/4 are UART A/B/C/D/E.
+
+	config TEGRA_DEBUG_UARTA
+		bool "UART A"
+
+	config TEGRA_DEBUG_UARTB
+		bool "UART B"
+
+	config TEGRA_DEBUG_UARTC
+		bool "UART C"
+
+	config TEGRA_DEBUG_UARTD
+		bool "UART D"
+
+	config TEGRA_DEBUG_UARTE
+		bool "UART E"
+
+endchoice
+
 config DEBUG_LL_INCLUDE
 	string
 	default "debug/icedcc.S" if DEBUG_ICEDCC
@@ -469,6 +506,8 @@ config DEBUG_LL_INCLUDE
 	default "debug/sunxi.S" if DEBUG_SUNXI_UART0 || DEBUG_SUNXI_UART1
 	default "debug/vexpress.S" if DEBUG_VEXPRESS_UART0_DETECT || \
 		DEBUG_VEXPRESS_UART0_CA9 || DEBUG_VEXPRESS_UART0_RS1
+	default "debug/tegra.S" if DEBUG_TEGRA_UART
+	default "debug/zynq.S" if DEBUG_ZYNQ_UART0 || DEBUG_ZYNQ_UART1
 	default "mach/debug-macro.S"
 
 config EARLY_PRINTK
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 9c60f474a559..30c443c406f3 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -202,7 +202,6 @@ machine-$(CONFIG_ARCH_SUNXI)		+= sunxi
 plat-$(CONFIG_ARCH_OMAP)	+= omap
 plat-$(CONFIG_ARCH_S3C64XX)	+= samsung
 plat-$(CONFIG_PLAT_IOP)		+= iop
-plat-$(CONFIG_PLAT_NOMADIK)	+= nomadik
 plat-$(CONFIG_PLAT_ORION)	+= orion
 plat-$(CONFIG_PLAT_PXA)		+= pxa
 plat-$(CONFIG_PLAT_S3C24XX)	+= s3c24xx samsung
diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi
index fba998e3954a..b8effa1cbda7 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/tegra20.dtsi
@@ -91,6 +91,12 @@
 		};
 	};
 
+	timer@50004600 {
+		compatible = "arm,cortex-a9-twd-timer";
+		reg = <0x50040600 0x20>;
+		interrupts = <1 13 0x304>;
+	};
+
 	cache-controller@50043000 {
 		compatible = "arm,pl310-cache";
 		reg = <0x50043000 0x1000>;
@@ -108,6 +114,15 @@
 		#interrupt-cells = <3>;
 	};
 
+	timer@60005000 {
+		compatible = "nvidia,tegra20-timer";
+		reg = <0x60005000 0x60>;
+		interrupts = <0 0 0x04
+			      0 1 0x04
+			      0 41 0x04
+			      0 42 0x04>;
+	};
+
 	apbdma: dma {
 		compatible = "nvidia,tegra20-apbdma";
 		reg = <0x6000a000 0x1200>;
@@ -225,6 +240,12 @@
 		#pwm-cells = <2>;
 	};
 
+	rtc {
+		compatible = "nvidia,tegra20-rtc";
+		reg = <0x7000e000 0x100>;
+		interrupts = <0 2 0x04>;
+	};
+
 	i2c@7000c000 {
 		compatible = "nvidia,tegra20-i2c";
 		reg = <0x7000c000 0x100>;
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi
index efa603d47a6a..529fdb82dfdb 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/tegra30.dtsi
@@ -91,6 +91,12 @@
 		};
 	};
 
+	timer@50004600 {
+		compatible = "arm,cortex-a9-twd-timer";
+		reg = <0x50040600 0x20>;
+		interrupts = <1 13 0xf04>;
+	};
+
 	cache-controller@50043000 {
 		compatible = "arm,pl310-cache";
 		reg = <0x50043000 0x1000>;
@@ -108,6 +114,17 @@
 		#interrupt-cells = <3>;
 	};
 
+	timer@60005000 {
+		compatible = "nvidia,tegra30-timer", "nvidia,tegra20-timer";
+		reg = <0x60005000 0x400>;
+		interrupts = <0 0 0x04
+			      0 1 0x04
+			      0 41 0x04
+			      0 42 0x04
+			      0 121 0x04
+			      0 122 0x04>;
+	};
+
 	apbdma: dma {
 		compatible = "nvidia,tegra30-apbdma", "nvidia,tegra20-apbdma";
 		reg = <0x6000a000 0x1400>;
@@ -219,6 +236,12 @@
 		#pwm-cells = <2>;
 	};
 
+	rtc {
+		compatible = "nvidia,tegra30-rtc", "nvidia,tegra20-rtc";
+		reg = <0x7000e000 0x100>;
+		interrupts = <0 2 0x04>;
+	};
+
 	i2c@7000c000 {
 		compatible =  "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
 		reg = <0x7000c000 0x100>;
diff --git a/arch/arm/include/debug/tegra.S b/arch/arm/include/debug/tegra.S
new file mode 100644
index 000000000000..883d7c22fd9d
--- /dev/null
+++ b/arch/arm/include/debug/tegra.S
@@ -0,0 +1,223 @@
+/*
+ * Copyright (C) 2010,2011 Google, Inc.
+ * Copyright (C) 2011-2012 NVIDIA CORPORATION. All Rights Reserved.
+ *
+ * Author:
+ *	Colin Cross <ccross@google.com>
+ *	Erik Gilling <konkers@google.com>
+ *	Doug Anderson <dianders@chromium.org>
+ *	Stephen Warren <swarren@nvidia.com>
+ *
+ * Portions based on mach-omap2's debug-macro.S
+ * Copyright (C) 1994-1999 Russell King
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/serial_reg.h>
+
+#define UART_SHIFT 2
+
+/* Physical addresses */
+#define TEGRA_CLK_RESET_BASE		0x60006000
+#define TEGRA_APB_MISC_BASE		0x70000000
+#define TEGRA_UARTA_BASE		0x70006000
+#define TEGRA_UARTB_BASE		0x70006040
+#define TEGRA_UARTC_BASE		0x70006200
+#define TEGRA_UARTD_BASE		0x70006300
+#define TEGRA_UARTE_BASE		0x70006400
+#define TEGRA_PMC_BASE			0x7000e400
+
+#define TEGRA_CLK_RST_DEVICES_L		(TEGRA_CLK_RESET_BASE + 0x04)
+#define TEGRA_CLK_RST_DEVICES_H		(TEGRA_CLK_RESET_BASE + 0x08)
+#define TEGRA_CLK_RST_DEVICES_U		(TEGRA_CLK_RESET_BASE + 0x0c)
+#define TEGRA_CLK_OUT_ENB_L		(TEGRA_CLK_RESET_BASE + 0x10)
+#define TEGRA_CLK_OUT_ENB_H		(TEGRA_CLK_RESET_BASE + 0x14)
+#define TEGRA_CLK_OUT_ENB_U		(TEGRA_CLK_RESET_BASE + 0x18)
+#define TEGRA_PMC_SCRATCH20		(TEGRA_PMC_BASE + 0xa0)
+#define TEGRA_APB_MISC_GP_HIDREV	(TEGRA_APB_MISC_BASE + 0x804)
+
+/*
+ * Must be 1MB-aligned since a 1MB mapping is used early on.
+ * Must not overlap with regions in mach-tegra/io.c:tegra_io_desc[].
+ */
+#define UART_VIRTUAL_BASE		0xfe100000
+
+#define checkuart(rp, rv, lhu, bit, uart) \
+		/* Load address of CLK_RST register */ \
+		movw	rp, #TEGRA_CLK_RST_DEVICES_##lhu & 0xffff ; \
+		movt	rp, #TEGRA_CLK_RST_DEVICES_##lhu >> 16 ; \
+		/* Load value from CLK_RST register */ \
+		ldr	rp, [rp, #0] ; \
+		/* Test UART's reset bit */ \
+		tst	rp, #(1 << bit) ; \
+		/* If set, can't use UART; jump to save no UART */ \
+		bne	90f ; \
+		/* Load address of CLK_OUT_ENB register */ \
+		movw	rp, #TEGRA_CLK_OUT_ENB_##lhu & 0xffff ; \
+		movt	rp, #TEGRA_CLK_OUT_ENB_##lhu >> 16 ; \
+		/* Load value from CLK_OUT_ENB register */ \
+		ldr	rp, [rp, #0] ; \
+		/* Test UART's clock enable bit */ \
+		tst	rp, #(1 << bit) ; \
+		/* If clear, can't use UART; jump to save no UART */ \
+		beq	90f ; \
+		/* Passed all tests, load address of UART registers */ \
+		movw	rp, #TEGRA_UART##uart##_BASE & 0xffff ; \
+		movt	rp, #TEGRA_UART##uart##_BASE >> 16 ; \
+		/* Jump to save UART address */ \
+		b 91f
+
+		.macro  addruart, rp, rv, tmp
+		adr	\rp, 99f		@ actual addr of 99f
+		ldr	\rv, [\rp]		@ linked addr is stored there
+		sub	\rv, \rv, \rp		@ offset between the two
+		ldr	\rp, [\rp, #4]		@ linked tegra_uart_config
+		sub	\tmp, \rp, \rv		@ actual tegra_uart_config
+		ldr	\rp, [\tmp]		@ Load tegra_uart_config
+		cmp	\rp, #1			@ needs initialization?
+		bne	100f			@ no; go load the addresses
+		mov	\rv, #0			@ yes; record init is done
+		str	\rv, [\tmp]
+
+#ifdef CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA
+		/* Check ODMDATA */
+10:		movw	\rp, #TEGRA_PMC_SCRATCH20 & 0xffff
+		movt	\rp, #TEGRA_PMC_SCRATCH20 >> 16
+		ldr	\rp, [\rp, #0]		@ Load PMC_SCRATCH20
+		ubfx	\rv, \rp, #18, #2	@ 19:18 are console type
+		cmp	\rv, #2			@ 2 and 3 mean DCC, UART
+		beq	11f			@ some boards swap the meaning
+		cmp	\rv, #3			@ so accept either
+		bne	90f
+11:		ubfx	\rv, \rp, #15, #3	@ 17:15 are UART ID
+		cmp	\rv, #0			@ UART 0?
+		beq	20f
+		cmp	\rv, #1			@ UART 1?
+		beq	21f
+		cmp	\rv, #2			@ UART 2?
+		beq	22f
+		cmp	\rv, #3			@ UART 3?
+		beq	23f
+		cmp	\rv, #4			@ UART 4?
+		beq	24f
+		b	90f			@ invalid
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTA) || \
+    defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+		/* Check UART A validity */
+20:		checkuart(\rp, \rv, L, 6, A)
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTB) || \
+    defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+		/* Check UART B validity */
+21:		checkuart(\rp, \rv, L, 7, B)
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTC) || \
+    defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+		/* Check UART C validity */
+22:		checkuart(\rp, \rv, H, 23, C)
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTD) || \
+    defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+		/* Check UART D validity */
+23:		checkuart(\rp, \rv, U, 1, D)
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTE) || \
+    defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+		/* Check UART E validity */
+24:
+		checkuart(\rp, \rv, U, 2, E)
+#endif
+
+		/* No valid UART found */
+90:		mov	\rp, #0
+		/* fall through */
+
+		/* Record whichever UART we chose */
+91:		str	\rp, [\tmp, #4]		@ Store in tegra_uart_phys
+		cmp	\rp, #0			@ Valid UART address?
+		bne	92f			@ Yes, go process it
+		str	\rp, [\tmp, #8]		@ Store 0 in tegra_uart_virt
+		b	100f			@ Done
+92:		and	\rv, \rp, #0xffffff	@ offset within 1MB section
+		add	\rv, \rv, #UART_VIRTUAL_BASE
+		str	\rv, [\tmp, #8]		@ Store in tegra_uart_virt
+		movw	\rv, #TEGRA_APB_MISC_GP_HIDREV & 0xffff
+		movt	\rv, #TEGRA_APB_MISC_GP_HIDREV >> 16
+		ldr	\rv, [\rv, #0]		@ Load HIDREV
+		ubfx	\rv, \rv, #8, #8	@ 15:8 are SoC version
+		cmp	\rv, #0x20		@ Tegra20?
+		moveq	\rv, #0x75		@ Tegra20 divisor
+		movne	\rv, #0xdd		@ Tegra30 divisor
+		str	\rv, [\tmp, #12]	@ Save divisor to scratch
+		/* uart[UART_LCR] = UART_LCR_WLEN8 | UART_LCR_DLAB; */
+		mov	\rv, #UART_LCR_WLEN8 | UART_LCR_DLAB
+		str	\rv, [\rp, #UART_LCR << UART_SHIFT]
+		/* uart[UART_DLL] = div & 0xff; */
+		ldr	\rv, [\tmp, #12]
+		and	\rv, \rv, #0xff
+		str	\rv, [\rp, #UART_DLL << UART_SHIFT]
+		/* uart[UART_DLM] = div >> 8; */
+		ldr	\rv, [\tmp, #12]
+		lsr	\rv, \rv, #8
+		str	\rv, [\rp, #UART_DLM << UART_SHIFT]
+		/* uart[UART_LCR] = UART_LCR_WLEN8; */
+		mov	\rv, #UART_LCR_WLEN8
+		str	\rv, [\rp, #UART_LCR << UART_SHIFT]
+		b	100f
+
+		.align
+99:		.word	.
+		.word	tegra_uart_config
+		.ltorg
+
+		/* Load previously selected UART address */
+100:		ldr	\rp, [\tmp, #4]		@ Load tegra_uart_phys
+		ldr	\rv, [\tmp, #8]		@ Load tegra_uart_virt
+		.endm
+
+/*
+ * Code below is swiped from <asm/hardware/debug-8250.S>, but add an extra
+ * check to make sure that the UART address is actually valid.
+ */
+
+		.macro	senduart, rd, rx
+		cmp	\rx, #0
+		strneb	\rd, [\rx, #UART_TX << UART_SHIFT]
+1001:
+		.endm
+
+		.macro	busyuart, rd, rx
+		cmp	\rx, #0
+		beq	1002f
+1001:		ldrb	\rd, [\rx, #UART_LSR << UART_SHIFT]
+		and	\rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE
+		teq	\rd, #UART_LSR_TEMT | UART_LSR_THRE
+		bne	1001b
+1002:
+		.endm
+
+		.macro	waituart, rd, rx
+#ifdef FLOW_CONTROL
+		cmp	\rx, #0
+		beq	1002f
+1001:		ldrb	\rd, [\rx, #UART_MSR << UART_SHIFT]
+		tst	\rd, #UART_MSR_CTS
+		beq	1001b
+1002:
+#endif
+		.endm
diff --git a/arch/arm/mach-zynq/include/mach/debug-macro.S b/arch/arm/include/debug/zynq.S
index 3ab0be1f6191..f9aa9740a73f 100644
--- a/arch/arm/mach-zynq/include/mach/debug-macro.S
+++ b/arch/arm/include/debug/zynq.S
@@ -1,5 +1,4 @@
-/* arch/arm/mach-zynq/include/mach/debug-macro.S
- *
+/*
  * Debugging macro include header
  *
  *  Copyright (C) 2011 Xilinx
@@ -13,9 +12,25 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */
+#define UART_CR_OFFSET		0x00  /* Control Register [8:0] */
+#define UART_SR_OFFSET		0x2C  /* Channel Status [11:0] */
+#define UART_FIFO_OFFSET	0x30  /* FIFO [15:0] or [7:0] */
+
+#define UART_SR_TXFULL		0x00000010	/* TX FIFO full */
+#define UART_SR_TXEMPTY		0x00000008	/* TX FIFO empty */
+
+#define UART0_PHYS		0xE0000000
+#define UART1_PHYS		0xE0001000
+#define UART_SIZE		SZ_4K
+#define UART_VIRT		0xF0001000
+
+#if IS_ENABLED(CONFIG_DEBUG_ZYNQ_UART1)
+# define LL_UART_PADDR		UART1_PHYS
+#else
+# define LL_UART_PADDR		UART0_PHYS
+#endif
 
-#include <mach/zynq_soc.h>
-#include <mach/uart.h>
+#define LL_UART_VADDR		UART_VIRT
 
 		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =LL_UART_PADDR	@ physical
diff --git a/arch/arm/mach-nomadik/Kconfig b/arch/arm/mach-nomadik/Kconfig
index c744946ef022..706dc5727bbe 100644
--- a/arch/arm/mach-nomadik/Kconfig
+++ b/arch/arm/mach-nomadik/Kconfig
@@ -4,7 +4,7 @@ menu "Nomadik boards"
 
 config MACH_NOMADIK_8815NHK
 	bool "ST 8815 Nomadik Hardware Kit (evaluation board)"
-	select HAS_MTU
+	select CLKSRC_NOMADIK_MTU
 	select NOMADIK_8815
 
 endmenu
diff --git a/arch/arm/mach-nomadik/board-nhk8815.c b/arch/arm/mach-nomadik/board-nhk8815.c
index 22ef8a1abe08..5ccdf53c5a9d 100644
--- a/arch/arm/mach-nomadik/board-nhk8815.c
+++ b/arch/arm/mach-nomadik/board-nhk8815.c
@@ -25,18 +25,16 @@
 #include <linux/io.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/platform_data/pinctrl-nomadik.h>
+#include <linux/platform_data/clocksource-nomadik-mtu.h>
+#include <linux/platform_data/mtd-nomadik-nand.h>
 #include <asm/hardware/vic.h>
 #include <asm/sizes.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
-#include <asm/mach/irq.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/time.h>
-
-#include <plat/mtu.h>
-
-#include <linux/platform_data/mtd-nomadik-nand.h>
 #include <mach/fsmc.h>
+#include <mach/irqs.h>
 
 #include "cpu-8815.h"
 
@@ -260,7 +258,7 @@ static void __init nomadik_timer_init(void)
 	src_cr |= SRC_CR_INIT_VAL;
 	writel(src_cr, io_p2v(NOMADIK_SRC_BASE));
 
-	nmdk_timer_init(io_p2v(NOMADIK_MTU0_BASE));
+	nmdk_timer_init(io_p2v(NOMADIK_MTU0_BASE), IRQ_MTU0);
 }
 
 static struct sys_timer nomadik_timer = {
diff --git a/arch/arm/mach-nomadik/include/mach/irqs.h b/arch/arm/mach-nomadik/include/mach/irqs.h
index a118e615f865..b549d0571548 100644
--- a/arch/arm/mach-nomadik/include/mach/irqs.h
+++ b/arch/arm/mach-nomadik/include/mach/irqs.h
@@ -72,7 +72,7 @@
 #define NOMADIK_NR_GPIO			128 /* last 4 not wired to pins */
 #define NOMADIK_GPIO_TO_IRQ(gpio)	((gpio) + NOMADIK_GPIO_OFFSET)
 #define NOMADIK_IRQ_TO_GPIO(irq)	((irq) - NOMADIK_GPIO_OFFSET)
-#define NR_IRQS				NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO)
+#define NOMADIK_NR_IRQS			NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO)
 
 /* Following two are used by entry_macro.S, to access our dual-vic */
 #define VIC_REG_IRQSR0		0
diff --git a/arch/arm/mach-tegra/Kconfig b/arch/arm/mach-tegra/Kconfig
index 9ff6f6ea3617..e426d1b7747e 100644
--- a/arch/arm/mach-tegra/Kconfig
+++ b/arch/arm/mach-tegra/Kconfig
@@ -57,57 +57,6 @@ config TEGRA_AHB
 	  which controls AHB bus master arbitration and some
 	  perfomance parameters(priority, prefech size).
 
-choice
-        prompt "Default low-level debug console UART"
-        default TEGRA_DEBUG_UART_NONE
-
-config TEGRA_DEBUG_UART_NONE
-        bool "None"
-
-config TEGRA_DEBUG_UARTA
-        bool "UART-A"
-
-config TEGRA_DEBUG_UARTB
-        bool "UART-B"
-
-config TEGRA_DEBUG_UARTC
-        bool "UART-C"
-
-config TEGRA_DEBUG_UARTD
-        bool "UART-D"
-
-config TEGRA_DEBUG_UARTE
-        bool "UART-E"
-
-endchoice
-
-choice
-	prompt "Automatic low-level debug console UART"
-	default TEGRA_DEBUG_UART_AUTO_NONE
-
-config TEGRA_DEBUG_UART_AUTO_NONE
-	bool "None"
-
-config TEGRA_DEBUG_UART_AUTO_ODMDATA
-	bool "Via ODMDATA"
-	help
-	  Automatically determines which UART to use for low-level debug based
-	  on the ODMDATA value. This value is part of the BCT, and is written
-	  to the boot memory device using nvflash, or other flashing tool.
-	  When bits 19:18 are 3, then bits 17:15 indicate which UART to use;
-	  0/1/2/3/4 are UART A/B/C/D/E.
-
-config TEGRA_DEBUG_UART_AUTO_SCRATCH
-	bool "Via UART scratch register"
-	help
-	  Automatically determines which UART to use for low-level debug based
-	  on the UART scratch register value. Some bootloaders put ASCII 'D'
-	  in this register when they initialize their own console UART output.
-	  Using this option allows the kernel to automatically pick the same
-	  UART.
-
-endchoice
-
 config TEGRA_EMC_SCALING_ENABLE
 	bool "Enable scaling the memory frequency"
 
diff --git a/arch/arm/mach-tegra/common.c b/arch/arm/mach-tegra/common.c
index 11a74db51e5d..0816562725f6 100644
--- a/arch/arm/mach-tegra/common.c
+++ b/arch/arm/mach-tegra/common.c
@@ -45,14 +45,15 @@
  * kernel i