Merge tag 'qcom-arm64-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/late

Qualcomm ARM64 DT updates for v5.7

This brings initial support for the SM8250 and IPQ6018 platforms.

SDM845 gets audio, PCIe and IP-accelerator support, and the interconnect
providers are refactored. The Lenovo Yoga C630 has audio enabled and the
DB845c has PCIe, analog audio and low-speed interfaces enabled. The
SDM845 MTP has its display enabled and firmware location updated to
match linux-firmware.

SC7180 gains CPU topology and power properties. Interconnect providers,
eMMC, SD-card, multimedia clocks, display, Bluetooth, Venus are added.
Critical trip points are added as well as various fixes.

For MSM8916 FastRPC support is added, ETM power management and reserved
memory for Samsung A2015 are corrected.

MSM8996 switches to generic QMP phy driver for its UFS support. MSM8998
temporarily disables part of Coresight to boot without
clk_ignore_unused.  CEQ for eMMC on QCS404 is enabled.

Fixes throughout the platforms to fix binding compliance, correct
compatibles for SDHCI nodes and add gpio-ranges.

* tag 'qcom-arm64-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (56 commits)
  arm64: dts: qcom: sdm845-mtp: Relocate remoteproc firmware
  arm64: dts: sdm845: add IPA information
  arm64: dts: qcom: db845c: add analog audio support
  arm64: dts: qcom: sdm845: add pinctrl nodes for quat i2s
  arm64: dts: qcom: c630: Enable audio support
  arm64: dts: qcom: sdm845: add apr nodes
  arm64: dts: qcom: sdm845: add slimbus nodes
  arm64: dts: qcom: sc7180: Update reg names for SDHC
  arm64: dts: qcom: qcs404: Enable CQE support for eMMC
  arm64: dts: msm8916: Add fastrpc node
  arm64: dts: qcom: sm8250: Add sm8250 dts file
  arm64: dts: qcom: msm8998-mtp: Disable funnel 4 and 5
  arm64: dts: qcom: db845c: add Low speed expansion i2c and spi nodes
  arm64: dts: qcom: apq8016-sbc: Remove wrong regulator supply
  arm64: dts: qcom: sc7180: Added critical trip point Thermal-zones node
  arm64: dts: qcom: msm8998: Fix cpu compatible
  arm64: dts: qcom: sc7180: Add OSM L3 interconnect provider
  arm64: dts: qcom: sdm845: Add OSM L3 interconnect provider
  arm64: dts: sc7180: Add interconnect provider DT nodes
  arm64: dts: qcom: msm8996: Use generic QMP driver for UFS
  ...

Link: https://lore.kernel.org/r/20200318043823.GA470201@yoga
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

26 files changed, 2860 insertions, 69 deletions

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 973c0f079659..cc103f7020fd 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -2,6 +2,7 @@
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8016-sbc.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-db820c.dtb
 dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= ipq6018-cp01-c1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk01.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-longcheer-l8150.dtb
@@ -22,5 +23,6 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index 037e26b3f8d5..06aab44d798c 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -562,7 +562,6 @@
 
 &smd_rpm_regulators {
 	vdd_l1_l2_l3-supply = <&pm8916_s3>;
-	vdd_l5-supply = <&pm8916_s3>;
 	vdd_l4_l5_l6-supply = <&pm8916_s4>;
 	vdd_l7-supply = <&pm8916_s4>;
 
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index fff6115f2670..af87350b5547 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -999,13 +999,7 @@
 
 	vdda-phy-supply = <&vreg_l28a_0p925>;
 	vdda-pll-supply = <&vreg_l12a_1p8>;
-
-	vdda-phy-max-microamp = <18380>;
-	vdda-pll-max-microamp = <9440>;
-
 	vddp-ref-clk-supply = <&vreg_l25a_1p2>;
-	vddp-ref-clk-max-microamp = <100>;
-	vddp-ref-clk-always-on;
 };
 
 &ufshc {
diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
new file mode 100644
index 000000000000..b31117a93995
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ6018 CP01 board device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq6018.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ6018/AP-CP01-C1";
+	compatible = "qcom,ipq6018-cp01", "qcom,ipq6018";
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs-append = " swiotlb=1";
+	};
+};
+
+&blsp1_uart3 {
+	pinctrl-0 = <&serial_3_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&i2c_1 {
+	pinctrl-0 = <&i2c_1_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&spi_0 {
+	cs-select = <0>;
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		compatible = "n25q128a11";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&tlmm {
+	i2c_1_pins: i2c-1-pins {
+		pins = "gpio42", "gpio43";
+		function = "blsp2_i2c";
+		drive-strength = <8>;
+	};
+
+	spi_0_pins: spi-0-pins {
+		pins = "gpio38", "gpio39", "gpio40", "gpio41";
+		function = "blsp0_spi";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
new file mode 100644
index 000000000000..1aa8d8579463
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -0,0 +1,443 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ6018 SoC device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-ipq6018.h>
+#include <dt-bindings/reset/qcom,gcc-ipq6018.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&intc>;
+
+	clocks {
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};
+
+		xo: xo {
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+		};
+
+		L2_0: l2-cache {
+			compatible = "cache";
+			cache-level = <0x2>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm";
+		};
+	};
+
+	tcsr_mutex: hwlock {
+		compatible = "qcom,tcsr-mutex";
+		syscon = <&tcsr_mutex_regs 0 0x80>;
+		#hwlock-cells = <1>;
+	};
+
+	pmuv8: pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+					 IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	psci: psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		tz: tz@48500000 {
+			reg = <0x0 0x48500000 0x0 0x00200000>;
+			no-map;
+		};
+
+		smem_region: memory@4aa00000 {
+			reg = <0x0 0x4aa00000 0x0 0x00100000>;
+			no-map;
+		};
+
+		q6_region: memory@4ab00000 {
+			reg = <0x0 0x4ab00000 0x0 0x02800000>;
+			no-map;
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem_region>;
+		hwlocks = <&tcsr_mutex 0>;
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0xffffffff>;
+		dma-ranges;
+		compatible = "simple-bus";
+
+		prng: qrng@e1000 {
+			compatible = "qcom,prng-ee";
+			reg = <0xe3000 0x1000>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		cryptobam: dma@704000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x00704000 0x20000>;
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_CRYPTO_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <1>;
+			qcom,controlled-remotely = <1>;
+			qcom,config-pipe-trust-reg = <0>;
+		};
+
+		crypto: crypto@73a000 {
+			compatible = "qcom,crypto-v5.1";
+			reg = <0x0073a000 0x6000>;
+			clocks = <&gcc GCC_CRYPTO_AHB_CLK>,
+				<&gcc GCC_CRYPTO_AXI_CLK>,
+				<&gcc GCC_CRYPTO_CLK>;
+			clock-names = "iface", "bus", "core";
+			dmas = <&cryptobam 2>, <&cryptobam 3>;
+			dma-names = "rx", "tx";
+		};
+
+		tlmm: pinctrl@1000000 {
+			compatible = "qcom,ipq6018-pinctrl";
+			reg = <0x01000000 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&tlmm 0 80>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			serial_3_pins: serial3-pinmux {
+				pins = "gpio44", "gpio45";
+				function = "blsp2_uart";
+				drive-strength = <8>;
+				bias-pull-down;
+			};
+		};
+
+		gcc: gcc@1800000 {
+			compatible = "qcom,gcc-ipq6018";
+			reg = <0x01800000 0x80000>;
+			clocks = <&xo>, <&sleep_clk>;
+			clock-names = "xo", "sleep_clk";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		tcsr_mutex_regs: syscon@1905000 {
+			compatible = "syscon";
+			reg = <0x01905000 0x8000>;
+		};
+
+		tcsr_q6: syscon@1945000 {
+			compatible = "syscon";
+			reg = <0x01945000 0xe000>;
+		};
+
+		blsp_dma: dma@7884000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x07884000 0x2b000>;
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		blsp1_uart3: serial@78b1000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b1000 0x200>;
+			interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
+				<&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		spi_0: spi@78b5000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x078b5000 0x600>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			spi-max-frequency = <50000000>;
+			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+				<&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		spi_1: spi@78b6000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x078b6000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			spi-max-frequency = <50000000>;
+			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+				<&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		i2c_0: i2c@78b6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x078b6000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				<&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			clock-frequency  = <400000>;
+			dmas = <&blsp_dma 15>, <&blsp_dma 14>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2c_1: i2c@78b7000 { /* BLSP1 QUP2 */
+			compatible = "qcom,i2c-qup-v2.2.1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x078b7000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				<&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			clock-frequency  = <400000>;
+			dmas = <&blsp_dma 17>, <&blsp_dma 16>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		intc: interrupt-controller@b000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <0x3>;
+			reg =   <0x0b000000 0x1000>,  /*GICD*/
+				<0x0b002000 0x1000>,  /*GICC*/
+				<0x0b001000 0x1000>,  /*GICH*/
+				<0x0b004000 0x1000>;  /*GICV*/
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		watchdog@b017000 {
+			compatible = "qcom,kpss-wdt";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
+			reg = <0x0b017000 0x40>;
+			clocks = <&sleep_clk>;
+			timeout-sec = <10>;
+		};
+
+		apcs_glb: mailbox@b111000 {
+			compatible = "qcom,ipq8074-apcs-apps-global";
+			reg = <0x0b111000 0xc>;
+
+			#mbox-cells = <1>;
+		};
+
+		timer {
+			compatible = "arm,armv8-timer";
+			interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		};
+
+		timer@b120000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0b120000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@b120000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b121000 0x1000>,
+				      <0x0b122000 0x1000>;
+			};
+
+			frame@b123000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb123000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b124000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b124000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b125000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b125000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b126000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b126000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b127000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b127000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b128000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b128000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		q6v5_wcss: remoteproc@cd00000 {
+			compatible = "qcom,ipq8074-wcss-pil";
+			reg = <0x0cd00000 0x4040>,
+				<0x004ab000 0x20>;
+			reg-names = "qdsp6",
+				    "rmb";
+			interrupts-extended = <&intc GIC_SPI 325 IRQ_TYPE_EDGE_RISING>,
+					      <&wcss_smp2p_in 0 0>,
+					      <&wcss_smp2p_in 1 0>,
+					      <&wcss_smp2p_in 2 0>,
+					      <&wcss_smp2p_in 3 0>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+
+			resets = <&gcc GCC_WCSSAON_RESET>,
+				 <&gcc GCC_WCSS_BCR>,
+				 <&gcc GCC_WCSS_Q6_BCR>;
+
+			reset-names = "wcss_aon_reset",
+				      "wcss_reset",
+				      "wcss_q6_reset";
+
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "prng";
+
+			qcom,halt-regs = <&tcsr_q6 0xa000 0xd000 0x0>;
+
+			qcom,smem-states = <&wcss_smp2p_out 0>,
+					   <&wcss_smp2p_out 1>;
+			qcom,smem-state-names = "shutdown",
+						"stop";
+
+			memory-region = <&q6_region>;
+
+			glink-edge {
+				interrupts = <GIC_SPI 321 IRQ_TYPE_EDGE_RISING>;
+				qcom,remote-pid = <1>;
+				mboxes = <&apcs_glb 8>;
+
+				qrtr_requests {
+					qcom,glink-channels = "IPCRTR";
+				};
+			};
+		};
+
+	};
+
+	wcss: wcss-smp2p {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 322 IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&apcs_glb 9>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		wcss_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		wcss_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 67ee5f560104..2b31823d3ccd 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -21,6 +21,7 @@
 			reg = <0x1000000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 70>;
 			#gpio-cells = <0x2>;
 			interrupt-controller;
 			#interrupt-cells = <0x2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
index bd1eb3eeca53..43c5e0f882f1 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
@@ -15,6 +15,14 @@
 		stdout-path = "serial0";
 	};
 
+	reserved-memory {
+		/* Additional memory used by Samsung firmware modifications */
+		tz-apps@85500000 {
+			reg = <0x0 0x85500000 0x0 0xb00000>;
+			no-map;
+		};
+	};
+
 	soc {
 		sdhci@7824000 {
 			status = "okay";
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 9f31064f2374..a88a15f2352b 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -423,6 +423,7 @@
 			reg = <0x1000000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 122>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -860,7 +861,7 @@
 		};
 
 		tsens: thermal-sensor@4a9000 {
-			compatible = "qcom,msm8916-tsens";
+			compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1";
 			reg = <0x4a9000 0x1000>, /* TM */
 			      <0x4a8000 0x1000>; /* SROT */
 			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
@@ -1129,6 +1130,20 @@
 				qcom,remote-pid = <1>;
 
 				label = "hexagon";
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,smd-channels = "fastrpcsmd-apps-dsp";
+					label = "adsp";
+
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					cb@1{
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <1>;
+					};
+				};
 			};
 		};
 
@@ -1415,6 +1430,7 @@
 
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
+			arm,coresight-loses-context-with-cpu;
 
 			cpu = <&CPU0>;
 
@@ -1433,6 +1449,7 @@
 
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
+			arm,coresight-loses-context-with-cpu;
 
 			cpu = <&CPU1>;
 
@@ -1451,6 +1468,7 @@
 
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
+			arm,coresight-loses-context-with-cpu;
 
 			cpu = <&CPU2>;
 
@@ -1469,6 +1487,7 @@
 
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
+			arm,coresight-loses-context-with-cpu;
 
 			cpu = <&CPU3>;
 
diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi
index 8be60c08a9ab..2021795c99ad 100644
--- a/arch/arm64/boot/dts/qcom/msm8992.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi
@@ -171,6 +171,7 @@
 			reg = <0xfd510000 0x4000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 146>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index 3932757f78b7..b1c2d7d6a0f2 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -133,6 +133,7 @@
 			reg = <0xfd510000 0x4000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 146>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 7ae082ea14ea..14827adebd94 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -443,10 +443,13 @@
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			reg = <0x00300000 0x90000>;
+
+			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>;
+			clock-names = "cxo2";
 		};
 
 		tsens0: thermal-sensor@4a9000 {
-			compatible = "qcom,msm8996-tsens";
+			compatible = "qcom,msm8996-tsens", "qcom,tsens-v2";
 			reg = <0x004a9000 0x1000>, /* TM */
 			      <0x004a8000 0x1000>; /* SROT */
 			#qcom,sensors = <13>;
@@ -457,7 +460,7 @@
 		};
 
 		tsens1: thermal-sensor@4ad000 {
-			compatible = "qcom,msm8996-tsens";
+			compatible = "qcom,msm8996-tsens", "qcom,tsens-v2";
 			reg = <0x004ad000 0x1000>, /* TM */
 			      <0x004ac000 0x1000>; /* SROT */
 			#qcom,sensors = <8>;
@@ -695,6 +698,7 @@
 			reg = <0x01010000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 150>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -882,7 +886,7 @@
 			reg = <0x00624000 0x2500>;
 			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
 
-			phys = <&ufsphy>;
+			phys = <&ufsphy_lane>;
 			phy-names = "ufsphy";
 
 			power-domains = <&gcc UFS_GDSC>;
@@ -934,16 +938,25 @@
 		};
 
 		ufsphy: phy@627000 {
-			compatible = "qcom,msm8996-ufs-phy-qmp-14nm";
-			reg = <0x00627000 0xda8>;
-			reg-names = "phy_mem";
-			#phy-cells = <0>;
+			compatible = "qcom,msm8996-qmp-ufs-phy";
+			reg = <0x00627000 0x1c4>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_UFS_CLKREF_CLK>;
+			clock-names = "ref";
 
-			clock-names = "ref_clk_src", "ref_clk";
-			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
-				 <&gcc GCC_UFS_CLKREF_CLK>;
 			resets = <&ufshc 0>;
+			reset-names = "ufsphy";
 			status = "disabled";
+
+			ufsphy_lane: lanes@627400 {
+				reg = <0x627400 0x12c>,
+				      <0x627600 0x200>,
+				      <0x627c00 0x1b4>;
+				#phy-cells = <0>;
+			};
 		};
 
 		camss: camss@a00000 {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
index 0e0b9bc12945..8a14b2bf7bca 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
@@ -95,11 +95,15 @@
 };
 
 &funnel4 {
-	status = "okay";
+	// FIXME: Figure out why clock late_initcall crashes the board with
+	// this enabled.
+	// status = "okay";
 };
 
 &funnel5 {
-	status = "okay";
+	// FIXME: Figure out why clock late_initcall crashes the board with
+	// this enabled.
+	// status = "okay";
 };
 
 &pm8005_lsid1 {
diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
index 91f7f2d07597..c07fee6fd7eb 100644
--- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -130,7 +130,7 @@
 
 		CPU0: cpu@0 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
@@ -149,7 +149,7 @@
 
 		CPU1: cpu@1 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x1>;
 			enable-method = "psci";
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
@@ -164,7 +164,7 @@
 
 		CPU2: cpu@2 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x2>;
 			enable-method = "psci";
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
@@ -179,7 +179,7 @@
 
 		CPU3: cpu@3 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x3>;
 			enable-method = "psci";
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
@@ -194,7 +194,7 @@
 
 		CPU4: cpu@100 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
 			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
@@ -213,7 +213,7 @@
 
 		CPU5: cpu@101 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x101>;
 			enable-method = "psci";
 			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;