Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

power management changes for omap and imx

A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.

* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
  ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
  ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
  ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
  ARM: imx6q: build pm code only when CONFIG_PM selected
  ARM: mx5: use generic irq chip pm interface for pm functions on
  ARM: omap: pass minimal SoC/board data for UART from dt
  arm/dts: Add minimal device tree support for omap2420 and omap2430
  omap-serial: Add minimal device tree support
  omap-serial: Use default clock speed (48Mhz) if not specified
  omap-serial: Get rid of all pdev->id usage
  ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
  ARM: OMAP4: PRM: use PRCM interrupt handler
  ARM: OMAP3: pm: use prcm chain handler
  ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
  ARM: OMAP2+: mux: add support for PAD wakeup interrupts
  ARM: OMAP: PRCM: add suspend prepare / finish support
  ARM: OMAP: PRCM: add support for chain interrupt handler
  ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
  ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
  ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
  ...

37 files changed, 3222 insertions, 1083 deletions

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index b7407154c881..904bd1dfcd2e 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -365,6 +365,27 @@ config OMAP3_SDRC_AC_TIMING
 	  wish to say no.  Selecting yes without understanding what is
 	  going on could result in system crashes;
 
+config OMAP4_ERRATA_I688
+	bool "OMAP4 errata: Async Bridge Corruption"
+	depends on ARCH_OMAP4
+	select ARCH_HAS_BARRIERS
+	help
+	  If a data is stalled inside asynchronous bridge because of back
+	  pressure, it may be accepted multiple times, creating pointer
+	  misalignment that will corrupt next transfers on that data path
+	  until next reset of the system (No recovery procedure once the
+	  issue is hit, the path remains consistently broken). Async bridge
+	  can be found on path between MPU to EMIF and MPU to L3 interconnect.
+	  This situation can happen only when the idle is initiated by a
+	  Master Request Disconnection (which is trigged by software when
+	  executing WFI on CPU).
+	  The work-around for this errata needs all the initiators connected
+	  through async bridge must ensure that data path is properly drained
+	  before issuing WFI. This condition will be met if one Strongly ordered
+	  access is performed to the target right before executing the WFI.
+	  In MPU case, L3 T2ASYNC FIFO and DDR T2ASYNC FIFO needs to be drained.
+	  IO barrier ensure that there is no synchronisation loss on initiators
+	  operating on both interconnect port simultaneously.
 endmenu
 
 endif
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 6d226a76d057..fc9b238cbc19 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -11,10 +11,11 @@ hwmod-common				= omap_hwmod.o \
 					  omap_hwmod_common_data.o
 clock-common				= clock.o clock_common_data.o \
 					  clkt_dpll.o clkt_clksel.o
+secure-common                          = omap-smc.o omap-secure.o
 
-obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common)
-obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(hwmod-common)
-obj-$(CONFIG_ARCH_OMAP4) += prm44xx.o $(hwmod-common)
+obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common) $(secure-common)
+obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(hwmod-common) $(secure-common)
+obj-$(CONFIG_ARCH_OMAP4) += prm44xx.o $(hwmod-common) $(secure-common)
 
 obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
 
@@ -24,11 +25,13 @@ obj-$(CONFIG_TWL4030_CORE) += omap_twl.o
 obj-$(CONFIG_SMP)			+= omap-smp.o omap-headsmp.o
 obj-$(CONFIG_LOCAL_TIMERS)		+= timer-mpu.o
 obj-$(CONFIG_HOTPLUG_CPU)		+= omap-hotplug.o
-obj-$(CONFIG_ARCH_OMAP4)		+= omap44xx-smc.o omap4-common.o
+obj-$(CONFIG_ARCH_OMAP4)		+= omap4-common.o omap-wakeupgen.o \
+					   sleep44xx.o
 
 plus_sec := $(call as-instr,.arch_extension sec,+sec)
 AFLAGS_omap-headsmp.o			:=-Wa,-march=armv7-a$(plus_sec)
-AFLAGS_omap44xx-smc.o			:=-Wa,-march=armv7-a$(plus_sec)
+AFLAGS_omap-smc.o			:=-Wa,-march=armv7-a$(plus_sec)
+AFLAGS_sleep44xx.o			:=-Wa,-march=armv7-a$(plus_sec)
 
 # Functions loaded to SRAM
 obj-$(CONFIG_SOC_OMAP2420)		+= sram242x.o
@@ -62,7 +65,8 @@ obj-$(CONFIG_ARCH_OMAP2)		+= pm24xx.o
 obj-$(CONFIG_ARCH_OMAP2)		+= sleep24xx.o
 obj-$(CONFIG_ARCH_OMAP3)		+= pm34xx.o sleep34xx.o \
 					   cpuidle34xx.o
-obj-$(CONFIG_ARCH_OMAP4)		+= pm44xx.o
+obj-$(CONFIG_ARCH_OMAP4)		+= pm44xx.o omap-mpuss-lowpower.o \
+					   cpuidle44xx.o
 obj-$(CONFIG_PM_DEBUG)			+= pm-debug.o
 obj-$(CONFIG_OMAP_SMARTREFLEX)          += sr_device.o smartreflex.o
 obj-$(CONFIG_OMAP_SMARTREFLEX_CLASS3)	+= smartreflex-class3.o
@@ -77,6 +81,7 @@ endif
 endif
 
 # PRCM
+obj-y					+= prm_common.o
 obj-$(CONFIG_ARCH_OMAP2)		+= prcm.o cm2xxx_3xxx.o prm2xxx_3xxx.o
 obj-$(CONFIG_ARCH_OMAP3)		+= prcm.o cm2xxx_3xxx.o prm2xxx_3xxx.o \
 					   vc3xxx_data.o vp3xxx_data.o
@@ -86,7 +91,7 @@ obj-$(CONFIG_ARCH_OMAP3)		+= prcm.o cm2xxx_3xxx.o prm2xxx_3xxx.o \
 obj-$(CONFIG_ARCH_OMAP4)		+= prcm.o cm2xxx_3xxx.o cminst44xx.o \
 					   cm44xx.o prcm_mpu44xx.o \
 					   prminst44xx.o vc44xx_data.o \
-					   vp44xx_data.o
+					   vp44xx_data.o prm44xx.o
 
 # OMAP voltage domains
 voltagedomain-common			:= voltage.o vc.o vp.o
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 9996334cb687..383717ba63b9 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -475,106 +475,8 @@ static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
 static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
-
-static struct omap_device_pad serial1_pads[] __initdata = {
-	/*
-	 * Note that off output enable is an active low
-	 * signal. So setting this means pin is a
-	 * input enabled in off mode
-	 */
-	OMAP_MUX_STATIC("uart1_cts.uart1_cts",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_rts.uart1_rts",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_rx.uart1_rx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_tx.uart1_tx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLDOWN |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial1_data __initdata = {
-	.id		= 0,
-	.pads		= serial1_pads,
-	.pads_cnt	= ARRAY_SIZE(serial1_pads),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id		= 1,
-	.pads		= serial2_pads,
-	.pads_cnt	= ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id		= 2,
-	.pads		= serial3_pads,
-	.pads_cnt	= ARRAY_SIZE(serial3_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init_port(&serial1_data);
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
 #endif
 
 /*
@@ -711,7 +613,7 @@ static void __init omap_3430sdp_init(void)
 	else
 		gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1;
 	omap_ads7846_init(1, gpio_pendown, 310, NULL);
-	board_serial_init();
+	omap_serial_init();
 	omap_sdrc_init(hyb18m512160af6_sdrc_params, NULL);
 	usb_musb_init(NULL);
 	board_smc91x_init();
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 4b4c9e25a83e..2ceb75d21eb2 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -844,74 +844,8 @@ static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial4_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart4_rx.uart4_rx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart4_tx.uart4_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id		= 1,
-	.pads		= serial2_pads,
-	.pads_cnt	= ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id		= 2,
-	.pads		= serial3_pads,
-	.pads_cnt	= ARRAY_SIZE(serial3_pads),
-};
-
-static struct omap_board_data serial4_data __initdata = {
-	.id		= 3,
-	.pads		= serial4_pads,
-	.pads_cnt	= ARRAY_SIZE(serial4_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	struct omap_board_data bdata;
-	bdata.flags	= 0;
-	bdata.pads	= NULL;
-	bdata.pads_cnt	= 0;
-	bdata.id	= 0;
-	/* pass dummy data for UART1 */
-	omap_serial_init_port(&bdata);
-
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-	omap_serial_init_port(&serial4_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
  #endif
 
 static void omap4_sdp4430_wifi_mux_init(void)
@@ -961,7 +895,7 @@ static void __init omap_4430sdp_init(void)
 	omap4_i2c_init();
 	omap_sfh7741prox_init();
 	platform_add_devices(sdp4430_devices, ARRAY_SIZE(sdp4430_devices));
-	board_serial_init();
+	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
 	omap4_sdp4430_wifi_init();
 	omap4_twl6030_hsmmc_init(mmc);
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index f8c5b2cc7c9c..d58756060483 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -69,7 +69,6 @@ static void __init omap_generic_init(void)
 	if (node)
 		irq_domain_add_simple(node, 0);
 
-	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
 
 	of_platform_populate(NULL, omap_dt_match_table, NULL, NULL);
diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index 72d76ed94a65..42a4d11fad23 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -644,15 +644,15 @@ static inline void board_serial_init(void)
 	bdata.pads_cnt = 0;
 
 	bdata.id = 0;
-	omap_serial_init_port(&bdata);
+	omap_serial_init_port(&bdata, NULL);
 
 	bdata.id = 1;
-	omap_serial_init_port(&bdata);
+	omap_serial_init_port(&bdata, NULL);
 
 	bdata.id = 2;
 	bdata.pads = serial2_pads;
 	bdata.pads_cnt = ARRAY_SIZE(serial2_pads);
-	omap_serial_init_port(&bdata);
+	omap_serial_init_port(&bdata, NULL);
 }
 
 #else
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 8b06c6a60d02..e96a2e7ad36f 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -364,74 +364,8 @@ static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial4_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart4_rx.uart4_rx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart4_tx.uart4_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id             = 1,
-	.pads           = serial2_pads,
-	.pads_cnt       = ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id             = 2,
-	.pads           = serial3_pads,
-	.pads_cnt       = ARRAY_SIZE(serial3_pads),
-};
-
-static struct omap_board_data serial4_data __initdata = {
-	.id             = 3,
-	.pads           = serial4_pads,
-	.pads_cnt       = ARRAY_SIZE(serial4_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	struct omap_board_data bdata;
-	bdata.flags     = 0;
-	bdata.pads      = NULL;
-	bdata.pads_cnt  = 0;
-	bdata.id        = 0;
-	/* pass dummy data for UART1 */
-	omap_serial_init_port(&bdata);
-
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-	omap_serial_init_port(&serial4_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
 #endif
 
 /* Display DVI */
@@ -562,7 +496,7 @@ static void __init omap4_panda_init(void)
 	omap4_panda_i2c_init();
 	platform_add_devices(panda_devices, ARRAY_SIZE(panda_devices));
 	platform_device_register(&omap_vwlan_device);
-	board_serial_init();
+	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
 	omap4_twl6030_hsmmc_init(mmc);
 	omap4_ehci_init();
diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h
index 9403b2ce6c85..febffde2ff10 100644
--- a/arch/arm/mach-omap2/common.h
+++ b/arch/arm/mach-omap2/common.h
@@ -24,9 +24,11 @@
 
 #ifndef __ARCH_ARM_MACH_OMAP2PLUS_COMMON_H
 #define __ARCH_ARM_MACH_OMAP2PLUS_COMMON_H
+#ifndef __ASSEMBLER__
 
 #include <linux/delay.h>
 #include <plat/common.h>
+#include <asm/proc-fns.h>
 
 #ifdef CONFIG_SOC_OMAP2420
 extern void omap242x_map_common_io(void);
@@ -168,23 +170,23 @@ void omap3_intc_resume_idle(void);
 void omap2_intc_handle_irq(struct pt_regs *regs);
 void omap3_intc_handle_irq(struct pt_regs *regs);
 
-/*
- * wfi used in low power code. Directly opcode is used instead
- * of instruction to avoid mulit-omap build break
- */
-#ifdef CONFIG_THUMB2_KERNEL
-#define do_wfi() __asm__ __volatile__ ("wfi" : : : "memory")
-#else
-#define do_wfi()			\
-		__asm__ __volatile__ (".word	0xe320f003" : : : "memory")
+#ifdef CONFIG_CACHE_L2X0
+extern void __iomem *omap4_get_l2cache_base(void);
 #endif
 
-#ifdef CONFIG_CACHE_L2X0
-extern void __iomem *l2cache_base;
+#ifdef CONFIG_SMP
+extern void __iomem *omap4_get_scu_base(void);
+#else
+static inline void __iomem *omap4_get_scu_base(void)
+{
+	return NULL;
+}
 #endif
 
 extern void __init gic_init_irq(void);
 extern void omap_smc1(u32 fn, u32 arg);
+extern void __iomem *omap4_get_sar_ram_base(void);
+extern void omap_do_wfi(void);
 
 #ifdef CONFIG_SMP
 /* Needed for secondary core boot */
@@ -194,4 +196,44 @@ extern void omap_auxcoreboot_addr(u32 cpu_addr);
 extern u32 omap_read_auxcoreboot0(void);
 #endif
 
+#if defined(CONFIG_SMP) && defined(CONFIG_PM)
+extern int omap4_mpuss_init(void);
+extern int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state);
+extern int omap4_finish_suspend(unsigned long cpu_state);
+extern void omap4_cpu_resume(void);
+extern int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state);
+extern u32 omap4_mpuss_read_prev_context_state(void);
+#else
+static inline int omap4_enter_lowpower(unsigned int cpu,
+					unsigned int power_state)
+{
+	cpu_do_idle();
+	return 0;
+}
+
+static inline int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state)
+{
+	cpu_do_idle();
+	return 0;
+}
+
+static inline int omap4_mpuss_init(void)
+{
+	return 0;
+}
+
+static inline int omap4_finish_suspend(unsigned long cpu_state)
+{
+	return 0;
+}
+
+static inline void omap4_cpu_resume(void)
+{}
+
+static inline u32 omap4_mpuss_read_prev_context_state(void)
+{
+	return 0;
+}
+#endif
+#endif /* __ASSEMBLER__ */
 #endif /* __ARCH_ARM_MACH_OMAP2PLUS_COMMON_H */
diff --git a/arch/arm/mach-omap2/cpuidle34xx.c b/arch/arm/mach-omap2/cpuidle34xx.c
index e20332f4abdc..464cffde58fe 100644
--- a/arch/arm/mach-omap2/cpuidle34xx.c
+++ b/arch/arm/mach-omap2/cpuidle34xx.c
@@ -25,12 +25,12 @@
 #include <linux/sched.h>
 #include <linux/cpuidle.h>
 #include <linux/export.h>
+#include <linux/cpu_pm.h>
 
 #include <plat/prcm.h>
 #include <plat/irqs.h>
 #include "powerdomain.h"
 #include "clockdomain.h"
-#include <plat/serial.h>
 
 #include "pm.h"
 #include "control.h"
@@ -124,9 +124,23 @@ static int omap3_enter_idle(struct cpuidle_device *dev,
 		pwrdm_for_each_clkdm(core_pd, _cpuidle_deny_idle);
 	}
 
+	/*
+	 * Call idle CPU PM enter notifier chain so that
+	 * VFP context is saved.
+	 */
+	if (mpu_state == PWRDM_POWER_OFF)
+		cpu_pm_enter();
+
 	/* Execute ARM wfi */
 	omap_sram_idle();
 
+	/*
+	 * Call idle CPU PM enter notifier chain to restore
+	 * VFP context.
+	 */
+	if (pwrdm_read_prev_pwrst(mpu_pd) == PWRDM_POWER_OFF)
+		cpu_pm_exit();
+
 	/* Re-allow idle for C1 */
 	if (index == 0) {
 		pwrdm_for_each_clkdm(mpu_pd, _cpuidle_allow_idle);
@@ -245,11 +259,6 @@ static int omap3_enter_idle_bm(struct cpuidle_device *dev,
 	struct omap3_idle_statedata *cx;
 	int ret;
 
-	if (!omap3_can_sleep()) {
-		new_state_idx = drv->safe_state_index;
-		goto select_state;
-	}
-
 	/*
 	 * Prevent idle completely if CAM is active.
 	 * CAM does not have wakeup capability in OMAP3.
diff --git a/arch/arm/mach-omap2/cpuidle44xx.c b/arch/arm/mach-omap2/cpuidle44xx.c
new file mode 100644
index 000000000000..cfdbb86bc84e
--- /dev/null
+++ b/arch/arm/mach-omap2/cpuidle44xx.c
@@ -0,0 +1,245 @@
+/*
+ * OMAP4 CPU idle Routines
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ * Santosh Shilimkar <santosh.shilimkar@ti.com>
+ * Rajendra Nayak <rnayak@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/sched.h>
+#include <linux/cpuidle.h>
+#include <linux/cpu_pm.h>
+#include <linux/export.h>
+#include <linux/clockchips.h>
+
+#include <asm/proc-fns.h>
+
+#include "common.h"
+#include "pm.h"
+#include "prm.h"
+
+#ifdef CONFIG_CPU_IDLE
+
+/* Machine specific information to be recorded in the C-state driver_data */
+struct omap4_idle_statedata {
+	u32 cpu_state;
+	u32 mpu_logic_state;
+	u32 mpu_state;
+	u8 valid;
+};
+
+static struct cpuidle_params cpuidle_params_table[] = {
+	/* C1 - CPU0 ON + CPU1 ON + MPU ON */
+	{.exit_latency = 2 + 2 , .target_residency = 5, .valid = 1},
+	/* C2- CPU0 OFF + CPU1 OFF + MPU CSWR */
+	{.exit_latency = 328 + 440 , .target_residency = 960, .valid = 1},
+	/* C3 - CPU0 OFF + CPU1 OFF + MPU OSWR */
+	{.exit_latency = 460 + 518 , .target_residency = 1100, .valid = 1},
+};
+
+#define OMAP4_NUM_STATES ARRAY_SIZE(cpuidle_params_table)
+
+struct omap4_idle_statedata omap4_idle_data[OMAP4_NUM_STATES];
+static struct powerdomain *mpu_pd, *cpu0_pd, *cpu1_pd;
+
+/**
+ * omap4_enter_idle - Programs OMAP4 to enter the specified state
+ * @dev: cpuidle device
+ * @drv: cpuidle driver
+ * @index: the index of state to be entered
+ *
+ * Called from the CPUidle framework to program the device to the
+ * specified low power state selected by the governor.
+ * Returns the amount of time spent in the low power state.
+ */
+static int omap4_enter_idle(struct cpuidle_device *dev,
+			struct cpuidle_driver *drv,
+			int index)
+{
+	struct omap4_idle_statedata *cx =
+			cpuidle_get_statedata(&dev->states_usage[index]);
+	struct timespec ts_preidle, ts_postidle, ts_idle;
+	u32 cpu1_state;
+	int idle_time;
+	int new_state_idx;
+	int cpu_id = smp_processor_id();
+
+	/* Used to keep track of the total time in idle */
+	getnstimeofday(&ts_preidle);
+
+	local_irq_disable();
+	local_fiq_disable();
+
+	/*
+	 * CPU0 has to stay ON (i.e in C1) until CPU1 is OFF state.
+	 * This is necessary to honour hardware recommondation
+	 * of triggeing all the possible low power modes once CPU1 is
+	 * out of coherency and in OFF mode.
+	 * Update dev->last_state so that governor stats reflects right
+	 * data.
+	 */
+	cpu1_state = pwrdm_read_pwrst(cpu1_pd);
+	if (cpu1_state != PWRDM_POWER_OFF) {
+		new_state_idx = drv->safe_state_index;
+		cx = cpuidle_get_statedata(&dev->states_usage[new_state_idx]);
+	}
+
+	if (index > 0)
+		clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &cpu_id);
+
+	/*
+	 * Call idle CPU PM enter notifier chain so that
+	 * VFP and per CPU interrupt context is saved.
+	 */
+	if (cx->cpu_state == PWRDM_POWER_OFF)
+		cpu_pm_enter();
+
+	pwrdm_set_logic_retst(mpu_pd, cx->mpu_logic_state);
+	omap_set_pwrdm_state(mpu_pd, cx->mpu_state);
+
+	/*
+	 * Call idle CPU cluster PM enter notifier chain
+	 * to save GIC and wakeupgen context.
+	 */
+	if ((cx->mpu_state == PWRDM_POWER_RET) &&
+		(cx->mpu_logic_state == PWRDM_POWER_OFF))
+			cpu_cluster_pm_enter();
+
+	omap4_enter_lowpower(dev->cpu, cx->cpu_state);
+
+	/*
+	 * Call idle CPU PM exit notifier chain to restore
+	 * VFP and per CPU IRQ context. Only CPU0 state is
+	 * considered since CPU1 is managed by CPU hotplug.
+	 */
+	if (pwrdm_read_prev_pwrst(cpu0_pd) == PWRDM_POWER_OFF)
+		cpu_pm_exit();
+
+	/*
+	 * Call idle CPU cluster PM exit notifier chain
+	 * to restore GIC and wakeupgen context.
+	 */
+	if (omap4_mpuss_read_prev_context_state())
+		cpu_cluster_pm_exit();
+
+	if (index > 0)
+		clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &cpu_id);
+
+	getnstimeofday(&ts_postidle);
+	ts_idle = timespec_sub(ts_postidle, ts_preidle);
+
+	local_irq_enable();
+	local_fiq_enable();
+
+	idle_time = ts_idle.tv_nsec / NSEC_PER_USEC + ts_idle.tv_sec * \
+								USEC_PER_SEC;
+
+	/* Update cpuidle counters */
+	dev->last_residency = idle_time;
+
+	return index;
+}
+
+DEFINE_PER_CPU(struct cpuidle_device, omap4_idle_dev);
+
+struct cpuidle_driver omap4_idle_driver = {
+	.name =		"omap4_idle",
+	.owner =	THIS_MODULE,
+};
+
+static inline void _fill_cstate(struct cpuidle_driver *drv,
+					int idx, const char *descr)
+{
+	struct cpuidle_state *state = &drv->states[idx];
+
+	state->exit_latency	= cpuidle_params_table[idx].exit_latency;
+	state->target_residency	= cpuidle_params_table[idx].target_residency;
+	state->flags		= CPUIDLE_FLAG_TIME_VALID;
+	state->enter		= omap4_enter_idle;
+	sprintf(state->name, "C%d", idx + 1);
+	strncpy(state->desc, descr, CPUIDLE_DESC_LEN);
+}
+
+static inline struct omap4_idle_statedata *_fill_cstate_usage(
+					struct cpuidle_device *dev,
+					int idx)
+{
+	struct omap4_idle_statedata *cx = &omap4_idle_data[idx];
+	struct cpuidle_state_usage *state_usage = &dev->states_usage[idx];
+
+	cx->valid		= cpuidle_params_table[idx].valid;
+	cpuidle_set_statedata(state_usage, cx);
+
+	return cx;
+}
+
+
+