ARM: arm-soc: Merge branch 'next/pm2' into next/pm

Another smaller branch merged into next/pm before pull request.

Signed-off-by: Olof Johansson <olof@lixom.net>

30 files changed, 710 insertions, 35 deletions

diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards
index fc81a7d6b0f1..db5858e32d3f 100644
--- a/Documentation/devicetree/bindings/arm/arm-boards
+++ b/Documentation/devicetree/bindings/arm/arm-boards
@@ -9,6 +9,10 @@ Required properties (in root node):
 
 FPGA type interrupt controllers, see the versatile-fpga-irq binding doc.
 
+In the root node the Integrator/CP must have a /cpcon node pointing
+to the CP control registers, and the Integrator/AP must have a
+/syscon node pointing to the Integrator/AP system controller.
+
 
 ARM Versatile Application and Platform Baseboards
 -------------------------------------------------
diff --git a/Documentation/devicetree/bindings/arm/davinci.txt b/Documentation/devicetree/bindings/arm/davinci.txt
new file mode 100644
index 000000000000..cfaeda4274e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/davinci.txt
@@ -0,0 +1,17 @@
+Texas Instruments DaVinci Platforms Device Tree Bindings
+--------------------------------------------------------
+
+DA850/OMAP-L138/AM18x Evaluation Module (EVM) board
+Required root node properties:
+    - compatible = "ti,da850-evm", "ti,da850";
+
+EnBW AM1808 based CMC board
+Required root node properties:
+    - compatible = "enbw,cmc", "ti,da850;
+
+Generic DaVinci Boards
+----------------------
+
+DA850/OMAP-L138/AM18x generic board
+Required root node properties:
+    - compatible = "ti,da850";
diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt
index 6528e215c5fe..5216b419016a 100644
--- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt
+++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt
@@ -4,14 +4,13 @@ Exynos processors include support for multiple power domains which are used
 to gate power to one or more peripherals on the processor.
 
 Required Properties:
-- compatiable: should be one of the following.
+- compatible: should be one of the following.
     * samsung,exynos4210-pd - for exynos4210 type power domain.
 - reg: physical base address of the controller and length of memory mapped
     region.
 
-Optional Properties:
-- samsung,exynos4210-pd-off: Specifies that the power domain is in turned-off
-    state during boot and remains to be turned-off until explicitly turned-on.
+Node of a device using power domains must have a samsung,power-domain property
+defined with a phandle to respective power domain.
 
 Example:
 
@@ -19,3 +18,11 @@ Example:
 		compatible = "samsung,exynos4210-pd";
 		reg = <0x10023C00 0x10>;
 	};
+
+Example of the node using power domain:
+
+	node {
+		/* ... */
+		samsung,power-domain = <&lcd0>;
+		/* ... */
+	};
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index ac9e7516756e..f79818711e83 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -41,6 +41,10 @@ i.MX6 Quad SABRE Smart Device Board
 Required root node properties:
     - compatible = "fsl,imx6q-sabresd", "fsl,imx6q";
 
+i.MX6 Quad SABRE Automotive Board
+Required root node properties:
+    - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
+
 Generic i.MX boards
 -------------------
 
diff --git a/Documentation/devicetree/bindings/arm/omap/counter.txt b/Documentation/devicetree/bindings/arm/omap/counter.txt
new file mode 100644
index 000000000000..5bd8aa091315
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/counter.txt
@@ -0,0 +1,15 @@
+OMAP Counter-32K bindings
+
+Required properties:
+- compatible:	Must be "ti,omap-counter32k" for OMAP controllers
+- reg:		Contains timer register address range (base address and length)
+- ti,hwmods:	Name of the hwmod associated to the counter, which is typically
+		"counter_32k"
+
+Example:
+
+counter32k: counter@4a304000 {
+	compatible = "ti,omap-counter32k";
+	reg = <0x4a304000 0x20>;
+	ti,hwmods = "counter_32k";
+};
diff --git a/Documentation/devicetree/bindings/arm/omap/timer.txt b/Documentation/devicetree/bindings/arm/omap/timer.txt
new file mode 100644
index 000000000000..8732d4d41f8b
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/timer.txt
@@ -0,0 +1,31 @@
+OMAP Timer bindings
+
+Required properties:
+- compatible:		Must be "ti,omap2-timer" for OMAP2+ controllers.
+- reg:			Contains timer register address range (base address and
+			length).
+- interrupts: 		Contains the interrupt information for the timer. The
+			format is being dependent on which interrupt controller
+			the OMAP device uses.
+- ti,hwmods:		Name of the hwmod associated to the timer, "timer<X>",
+			where <X> is the instance number of the timer from the
+			HW spec.
+
+Optional properties:
+- ti,timer-alwon:	Indicates the timer is in an alway-on power domain.
+- ti,timer-dsp:		Indicates the timer can interrupt the on-chip DSP in
+			addition to the ARM CPU.
+- ti,timer-pwm: 	Indicates the timer can generate a PWM output.
+- ti,timer-secure: 	Indicates the timer is reserved on a secure OMAP device
+			and therefore cannot be used by the kernel.
+
+Example:
+
+timer12: timer@48304000 {
+	compatible = "ti,omap2-timer";
+	reg = <0x48304000 0x400>;
+	interrupts = <95>;
+	ti,hwmods = "timer12"
+	ti,timer-alwon;
+	ti,timer-secure;
+};
diff --git a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
new file mode 100644
index 000000000000..37824fac688e
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
@@ -0,0 +1,14 @@
+* Samsung SATA PHY Controller
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5-sata-phy"
+- reg               : <registers mapping>
+
+Example:
+        sata@ffe07000 {
+                compatible = "samsung,exynos5-sata-phy";
+                reg = <0xffe07000 0x1000>;
+        };
diff --git a/Documentation/devicetree/bindings/ata/exynos-sata.txt b/Documentation/devicetree/bindings/ata/exynos-sata.txt
new file mode 100644
index 000000000000..0849f1025e34
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/exynos-sata.txt
@@ -0,0 +1,17 @@
+* Samsung AHCI SATA Controller
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5-sata"
+- interrupts        : <interrupt mapping for SATA IRQ>
+- reg               : <registers mapping>
+- samsung,sata-freq : <frequency in MHz>
+
+Example:
+        sata@ffe08000 {
+                compatible = "samsung,exynos5-sata";
+                reg = <0xffe08000 0x1000>;
+                interrupts = <115>;
+        };
diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
index d2fe064a828b..63dd8051521c 100644
--- a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
+++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
@@ -2,9 +2,27 @@
 
 properties:
 - compatible : Should be "ti,omap-ocp2scp"
+- reg : Address and length of the register set for the device
 - #address-cells, #size-cells : Must be present if the device has sub-nodes
 - ranges : the child address space are mapped 1:1 onto the parent address space
 - ti,hwmods : must be "ocp2scp_usb_phy"
 
 Sub-nodes:
 All the devices connected to ocp2scp are described using sub-node to ocp2scp
+
+ocp2scp@4a0ad000 {
+	compatible = "ti,omap-ocp2scp";
+	reg = <0x4a0ad000 0x1f>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	ti,hwmods = "ocp2scp_usb_phy";
+
+	subnode1 {
+	...
+	};
+
+	subnode2 {
+	...
+	};
+};
diff --git a/Documentation/devicetree/bindings/clock/imx25-clock.txt b/Documentation/devicetree/bindings/clock/imx25-clock.txt
new file mode 100644
index 000000000000..c2a3525ecb4e
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/imx25-clock.txt
@@ -0,0 +1,162 @@
+* Clock bindings for Freescale i.MX25
+
+Required properties:
+- compatible: Should be "fsl,imx25-ccm"
+- reg: Address and length of the register set
+- interrupts: Should contain CCM interrupt
+- #clock-cells: Should be <1>
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  The following is a full list of i.MX25
+clocks and IDs.
+
+	Clock			ID
+	---------------------------
+	dummy			0
+	osc			1
+	mpll			2
+	upll			3
+	mpll_cpu_3_4		4
+	cpu_sel			5
+	cpu			6
+	ahb			7
+	usb_div			8
+	ipg			9
+	per0_sel		10
+	per1_sel		11
+	per2_sel		12
+	per3_sel		13
+	per4_sel		14
+	per5_sel		15
+	per6_sel		16
+	per7_sel		17
+	per8_sel		18
+	per9_sel		19
+	per10_sel		20
+	per11_sel		21
+	per12_sel		22
+	per13_sel		23
+	per14_sel		24
+	per15_sel		25
+	per0			26
+	per1			27
+	per2			28
+	per3			29
+	per4			30
+	per5			31
+	per6			32
+	per7			33
+	per8			34
+	per9			35
+	per10			36
+	per11			37
+	per12			38
+	per13			39
+	per14			40
+	per15			41
+	csi_ipg_per		42
+	epit_ipg_per		43
+	esai_ipg_per		44
+	esdhc1_ipg_per		45
+	esdhc2_ipg_per		46
+	gpt_ipg_per		47
+	i2c_ipg_per		48
+	lcdc_ipg_per		49
+	nfc_ipg_per		50
+	owire_ipg_per		51
+	pwm_ipg_per		52
+	sim1_ipg_per		53
+	sim2_ipg_per		54
+	ssi1_ipg_per		55
+	ssi2_ipg_per		56
+	uart_ipg_per		57
+	ata_ahb			58
+	reserved		59
+	csi_ahb			60
+	emi_ahb			61
+	esai_ahb		62
+	esdhc1_ahb		63
+	esdhc2_ahb		64
+	fec_ahb			65
+	lcdc_ahb		66
+	rtic_ahb		67
+	sdma_ahb		68
+	slcdc_ahb		69
+	usbotg_ahb		70
+	reserved		71
+	reserved		72
+	reserved		73
+	reserved		74
+	can1_ipg		75
+	can2_ipg		76
+	csi_ipg			77
+	cspi1_ipg		78
+	cspi2_ipg		79
+	cspi3_ipg		80
+	dryice_ipg		81
+	ect_ipg			82
+	epit1_ipg		83
+	epit2_ipg		84
+	reserved		85
+	esdhc1_ipg		86
+	esdhc2_ipg		87
+	fec_ipg			88
+	reserved		89
+	reserved		90
+	reserved		91
+	gpt1_ipg		92
+	gpt2_ipg		93
+	gpt3_ipg		94
+	gpt4_ipg		95
+	reserved		96
+	reserved		97
+	reserved		98
+	iim_ipg			99
+	reserved		100
+	reserved		101
+	kpp_ipg			102
+	lcdc_ipg		103
+	reserved		104
+	pwm1_ipg		105
+	pwm2_ipg		106
+	pwm3_ipg		107
+	pwm4_ipg		108
+	rngb_ipg		109
+	reserved		110
+	scc_ipg			111
+	sdma_ipg		112
+	sim1_ipg		113
+	sim2_ipg		114
+	slcdc_ipg		115
+	spba_ipg		116
+	ssi1_ipg		117
+	ssi2_ipg		118
+	tsc_ipg			119
+	uart1_ipg		120
+	uart2_ipg		121
+	uart3_ipg		122
+	uart4_ipg		123
+	uart5_ipg		124
+	reserved		125
+	wdt_ipg			126
+
+Examples:
+
+clks: ccm@53f80000 {
+	compatible = "fsl,imx25-ccm";
+	reg = <0x53f80000 0x4000>;
+	interrupts = <31>;
+	clock-output-names = ...
+			"uart_ipg",
+			"uart_serial",
+			...;
+};
+
+uart1: serial@43f90000 {
+	compatible = "fsl,imx25-uart", "fsl,imx21-uart";
+	reg = <0x43f90000 0x4000>;
+	interrupts = <45>;
+	clocks = <&clks 79>, <&clks 50>;
+	clock-names = "ipg", "per";
+	status = "disabled";
+};
diff --git a/Documentation/devicetree/bindings/clock/zynq-7000.txt b/Documentation/devicetree/bindings/clock/zynq-7000.txt
new file mode 100644
index 000000000000..23ae1db1bc13
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/zynq-7000.txt
@@ -0,0 +1,55 @@
+Device Tree Clock bindings for the Zynq 7000 EPP
+
+The Zynq EPP has several different clk providers, each with there own bindings.
+The purpose of this document is to document their usage.
+
+See clock_bindings.txt for more information on the generic clock bindings.
+See Chapter 25 of Zynq TRM for more information about Zynq clocks.
+
+== PLLs ==
+
+Used to describe the ARM_PLL, DDR_PLL, and IO_PLL.
+
+Required properties:
+- #clock-cells : shall be 0 (only one clock is output from this node)
+- compatible : "xlnx,zynq-pll"
+- reg : pair of u32 values, which are the address offsets within the SLCR
+        of the relevant PLL_CTRL register and PLL_CFG register respectively
+- clocks : phandle for parent clock.  should be the phandle for ps_clk
+
+Optional properties:
+- clock-output-names : name of the output clock
+
+Example:
+	armpll: armpll {
+		#clock-cells = <0>;
+		compatible = "xlnx,zynq-pll";
+		clocks = <&ps_clk>;
+		reg = <0x100 0x110>;
+		clock-output-names = "armpll";
+	};
+
+== Peripheral clocks ==
+
+Describes clock node for the SDIO, SMC, SPI, QSPI, and UART clocks.
+
+Required properties:
+- #clock-cells : shall be 1
+- compatible : "xlnx,zynq-periph-clock"
+- reg : a single u32 value, describing the offset within the SLCR where
+        the CLK_CTRL register is found for this peripheral
+- clocks : phandle for parent clocks.  should hold phandles for
+           the IO_PLL, ARM_PLL, and DDR_PLL in order
+- clock-output-names : names of the output clock(s).  For peripherals that have
+                       two output clocks (for example, the UART), two clocks
+                       should be listed.
+
+Example:
+	uart_clk: uart_clk {
+		#clock-cells = <1>;
+		compatible = "xlnx,zynq-periph-clock";
+		clocks = <&iopll &armpll &ddrpll>;
+		reg = <0x154>;
+		clock-output-names = "uart0_ref_clk",
+				     "uart1_ref_clk";
+	};
diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmi.txt b/Documentation/devicetree/bindings/drm/exynos/hdmi.txt
new file mode 100644
index 000000000000..589edee37394
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/exynos/hdmi.txt
@@ -0,0 +1,22 @@
+Device-Tree bindings for drm hdmi driver
+
+Required properties:
+- compatible: value should be "samsung,exynos5-hdmi".
+- reg: physical base address of the hdmi and length of memory mapped
+	region.
+- interrupts: interrupt number to the cpu.
+- hpd-gpio: following information about the hotplug gpio pin.
+	a) phandle of the gpio controller node.
+	b) pin number within the gpio controller.
+	c) pin function mode.
+	d) optional flags and pull up/down.
+	e) drive strength.
+
+Example:
+
+	hdmi {
+		compatible = "samsung,exynos5-hdmi";
+		reg = <0x14530000 0x100000>;
+		interrupts = <0 95 0>;
+		hpd-gpio = <&gpx3 7 0xf 1 3>;
+	};
diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt b/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt
new file mode 100644
index 000000000000..fa166d945809
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt
@@ -0,0 +1,12 @@
+Device-Tree bindings for hdmiddc driver
+
+Required properties:
+- compatible: value should be "samsung,exynos5-hdmiddc".
+- reg: I2C address of the hdmiddc device.
+
+Example:
+
+	hdmiddc {
+		compatible = "samsung,exynos5-hdmiddc";
+		reg = <0x50>;
+	};
diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt b/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt
new file mode 100644
index 000000000000..858f4f9b902f
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt
@@ -0,0 +1,12 @@
+Device-Tree bindings for hdmiphy driver
+
+Required properties:
+- compatible: value should be "samsung,exynos5-hdmiphy".
+- reg: I2C address of the hdmiphy device.
+
+Example:
+
+	hdmiphy {
+		compatible = "samsung,exynos5-hdmiphy";
+		reg = <0x38>;
+	};
diff --git a/Documentation/devicetree/bindings/drm/exynos/mixer.txt b/Documentation/devicetree/bindings/drm/exynos/mixer.txt
new file mode 100644
index 000000000000..9b2ea0343566
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/exynos/mixer.txt
@@ -0,0 +1,15 @@
+Device-Tree bindings for mixer driver
+
+Required properties:
+- compatible: value should be "samsung,exynos5-mixer".
+- reg: physical base address of the mixer and length of memory mapped
+	region.
+- interrupts: interrupt number to the cpu.
+
+Example:
+
+	mixer {
+		compatible = "samsung,exynos5-mixer";
+		reg = <0x14450000 0x10000>;
+		interrupts = <0 94 0>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt
new file mode 100644
index 000000000000..558cdf3c9abc
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt
@@ -0,0 +1,22 @@
+GPIO line that should be set high/low to power off a device
+
+Required properties:
+- compatible : should be "gpio-poweroff".
+- gpios : The GPIO to set high/low, see "gpios property" in
+  Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be
+  low to power down the board set it to "Active Low", otherwise set
+  gpio to "Active High".
+
+Optional properties:
+- input : Initially configure the GPIO line as an input. Only reconfigure
+  it to an output when the pm_power_off function is called. If this optional
+  property is not specified, the GPIO is initialized as an output in its
+  inactive state.
+
+
+Examples:
+
+gpio-poweroff {
+	compatible = "gpio-poweroff";
+	gpios = <&gpio 4 0>; /* GPIO 4 Active Low */
+};
diff --git a/Documentation/devicetree/bindings/gpio/leds-ns2.txt b/Documentation/devicetree/bindings/gpio/leds-ns2.txt
new file mode 100644
index 000000000000..aef3aca34d2d
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/leds-ns2.txt
@@ -0,0 +1,26 @@
+Binding for dual-GPIO LED found on Network Space v2 (and parents).
+
+Required properties:
+- compatible: "lacie,ns2-leds".
+
+Each LED is represented as a sub-node of the ns2-leds device.
+
+Required sub-node properties:
+- cmd-gpio: Command LED GPIO. See OF device-tree GPIO specification.
+- slow-gpio: Slow LED GPIO. See OF device-tree GPIO specification.
+
+Optional sub-node properties:
+- label: Name for this LED. If omitted, the label is taken from the node name.
+- linux,default-trigger: Trigger assigned to the LED.
+
+Example:
+
+ns2-leds {
+	compatible = "lacie,ns2-leds";
+
+	blue-sata {
+		label = "ns2:blue:sata";
+		slow-gpio = <&gpio0 29 0>;
+		cmd-gpio = <&gpio0 30 0>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt b/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt
index f3cf43b66f7e..3614242e7732 100644
--- a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt
+++ b/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt
@@ -12,13 +12,13 @@ Optional properties:
 Examples:
 
 i2c@83fc4000 { /* I2C2 on i.MX51 */
-	compatible = "fsl,imx51-i2c", "fsl,imx1-i2c";
+	compatible = "fsl,imx51-i2c", "fsl,imx21-i2c";
 	reg = <0x83fc4000 0x4000>;
 	interrupts = <63>;
 };
 
 i2c@70038000 { /* HS-I2C on i.MX51 */
-	compatible = "fsl,imx51-i2c", "fsl,imx1-i2c";
+	compatible = "fsl,imx51-i2c", "fsl,imx21-i2c";
 	reg = <0x70038000 0x4000>;
 	interrupts = <64>;
 	clock-frequency = <400000>;
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 2f5322b119eb..446859fcdca4 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -55,5 +55,7 @@ st-micro,24c256		i2c serial eeprom  (24cxx)
 stm,m41t00		Serial Access TIMEKEEPER
 stm,m41t62		Serial real-time clock (RTC) with alarm
 stm,m41t80		M41T80 - SERIAL ACCESS RTC WITH ALARMS
+taos,tsl2550		Ambient Light Sensor with SMBUS/Two Wire Serial Interface
 ti,tsc2003		I2C Touch-Screen Controller
 ti,tmp102		Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface
+ti,tmp275		Digital Temperature Sensor
diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt
new file mode 100644
index 000000000000..ca5a2c86480c
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt
@@ -0,0 +1,28 @@
+* Rohm BU21013 Touch Screen
+
+Required properties:
+ - compatible              : "rohm,bu21013_tp"
+ - reg                     :  I2C device address
+
+Optional properties:
+ - touch-gpio              : GPIO pin registering a touch event
+ - <supply_name>-supply    : Phandle to a regulator supply
+ - rohm,touch-max-x        : Maximum outward permitted limit in the X axis
+ - rohm,touch-max-y        : Maximum outward permitted limit in the Y axis
+ - rohm,flip-x             : Flip touch coordinates on the X axis
+ - rohm,flip-y             : Flip touch coordinates on the Y axis
+
+Example:
+
+	i2c@80110000 {
+		bu21013_tp@0x5c {
+			compatible = "rohm,bu21013_tp";
+			reg = <0x5c>;
+			touch-gpio = <&gpio2 20 0x4>;
+			avdd-supply = <&ab8500_ldo_aux1_reg>;
+
+			rohm,touch-max-x = <384>;
+			rohm,touch-max-y = <704>;
+			rohm,flip-y;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt
new file mode 100644
index 000000000000..67ec3d4ccc7f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt
@@ -0,0 +1,23 @@
+* Samsung Multi Format Codec (MFC)
+
+Multi Format Codec (MFC) is the IP present in Samsung SoCs which
+supports high resolution decoding and encoding functionalities.
+The MFC device driver is a v4l2 driver which can encode/decode
+video raw/elementary streams and has support for all popular
+video codecs.
+
+Required properties:
+  - compatible : value should be either one among the following
+	(a) "samsung,mfc-v5" for MFC v5 present in Exynos4 SoCs
+	(b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs
+
+  - reg : Physical base address of the IP registers and length of memory
+	  mapped region.
+
+  - interrupts : MFC interrupt number to the CPU.
+
+  - samsung,mfc-r : Base address of the first memory bank used by MFC
+		    for DMA contiguous memory allocation and its size.
+
+  - samsung,mfc-l : Base address of the second memory bank used by MFC
+		    for DMA contiguous memory allocation and its size.
diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt
index bc9549529014..c79bab025369 100644
--- a/Documentation/devicetree/bindings/net/mdio-gpio.txt
+++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt
@@ -8,9 +8,16 @@ gpios property as described in section VIII.1 in the following order:
 
 MDC, MDIO.
 
+Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases"
+node.
+
 Example:
 
-mdio {
+aliases {
+	mdio-gpio0 = <&mdio0>;
+};
+
+mdio0: mdio {
 	compatible = "virtual,mdio-gpio";
 	#address-cells = <1>;
 	#size-cells = <0>;
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt
index 361bccb7ec89..95daf6335c37 100644
--- a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt
@@ -7,8 +7,10 @@ Required properties:
 - compatible: "marvell,88f6180-pinctrl",
               "marvell,88f6190-pinctrl", "marvell,88f6192-pinctrl",
               "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl"
+              "marvell,98dx4122-pinctrl"
 
 This driver supports all kirkwood variants, i.e. 88f6180, 88f619x, and 88f628x.
+It also support the 88f6281-based variant in the 98dx412x Bobcat SoCs.
 
 Available mpp pins/groups and functions:
 Note: brackets (x) are not part of the mpp name for marvell,function and given
@@ -277,3 +279,40 @@ mpp46         46       gpio, ts(mp10), tdm(fs), lcd(hsync)
 mpp47         47       gpio, ts(mp11), tdm(drx), lcd(vsync)
 mpp48         48       gpio, ts(mp12), tdm(dtx), lcd(d16)
 mpp49         49       gpo, tdm(rx0ql), pex(clkreq), lcd(d17)
+
+* Marvell Bobcat 98dx4122
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, nand(io2), spi(cs)
+mpp1          1        gpo, nand(io3), spi(mosi)
+mpp2          2        gpo, nand(io4), spi(sck)
+mpp3          3        gpo, nand(io5), spi(miso)
+mpp4          4        gpio, nand(io6), uart0(rxd)
+mpp5          5        gpo, nand(io7), uart0(txd)
+mpp6          6        sysrst(out), spi(mosi)
+mpp7          7        gpo, pex(rsto), spi(cs)
+mpp8          8        gpio, twsi0(sda), uart0(rts), uart1(rts)
+mpp9          9        gpio, twsi(sck), uart0(cts), uart1(cts)
+mpp10         10       gpo, spi(sck), uart0(txd)
+mpp11         11       gpio, spi(miso), uart0(rxd)
+mpp13         13       gpio, uart1(txd)
+mpp14         14       gpio, uart1(rxd)
+mpp15         15       gpio, uart0(rts)
+mpp16         16       gpio, uart0(cts)
+mpp18         18       gpo, nand(io0)
+mpp19         19       gpo, nand(io1)
+mpp34         34       gpio
+mpp35         35       gpio
+mpp36         36       gpio
+mpp37         37       gpio
+mpp38         38       gpio
+mpp39         39       gpio
+mpp40         40       gpio
+mpp41         41       gpio
+mpp42         42       gpio
+mpp43         43       gpio
+mpp44         44       gpio
+mpp45         45       gpio
+mpp49         49       gpio
+
diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
index 03dee50532f5..e97a27856b21 100644
--- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -8,13 +8,20 @@ on-chip controllers onto these pads.
 Required Properties:
 - compatible: should be one of the following.
   - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
+  - "samsung,pinctrl-exynos4x12":