Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:
 "Highlights:

   1) Steady transitioning of the BPF instructure to a generic spot so
      all kernel subsystems can make use of it, from Alexei Starovoitov.

   2) SFC driver supports busy polling, from Alexandre Rames.

   3) Take advantage of hash table in UDP multicast delivery, from David
      Held.

   4) Lighten locking, in particular by getting rid of the LRU lists, in
      inet frag handling.  From Florian Westphal.

   5) Add support for various RFC6458 control messages in SCTP, from
      Geir Ola Vaagland.

   6) Allow to filter bridge forwarding database dumps by device, from
      Jamal Hadi Salim.

   7) virtio-net also now supports busy polling, from Jason Wang.

   8) Some low level optimization tweaks in pktgen from Jesper Dangaard
      Brouer.

   9) Add support for ipv6 address generation modes, so that userland
      can have some input into the process.  From Jiri Pirko.

  10) Consolidate common TCP connection request code in ipv4 and ipv6,
      from Octavian Purdila.

  11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.

  12) Generic resizable RCU hash table, with intial users in netlink and
      nftables.  From Thomas Graf.

  13) Maintain a name assignment type so that userspace can see where a
      network device name came from (enumerated by kernel, assigned
      explicitly by userspace, etc.) From Tom Gundersen.

  14) Automatic flow label generation on transmit in ipv6, from Tom
      Herbert.

  15) New packet timestamping facilities from Willem de Bruijn, meant to
      assist in measuring latencies going into/out-of the packet
      scheduler, latency from TCP data transmission to ACK, etc"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
  cxgb4 : Disable recursive mailbox commands when enabling vi
  net: reduce USB network driver config options.
  tg3: Modify tg3_tso_bug() to handle multiple TX rings
  amd-xgbe: Perform phy connect/disconnect at dev open/stop
  amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
  net: sun4i-emac: fix memory leak on bad packet
  sctp: fix possible seqlock seadlock in sctp_packet_transmit()
  Revert "net: phy: Set the driver when registering an MDIO bus device"
  cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
  team: Simplify return path of team_newlink
  bridge: Update outdated comment on promiscuous mode
  net-timestamp: ACK timestamp for bytestreams
  net-timestamp: TCP timestamping
  net-timestamp: SCHED timestamp on entering packet scheduler
  net-timestamp: add key to disambiguate concurrent datagrams
  net-timestamp: move timestamp flags out of sk_flags
  net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
  cxgb4i : Move stray CPL definitions to cxgb4 driver
  tcp: reduce spurious retransmits due to transient SACK reneging
  qlcnic: Initialize dcbnl_ops before register_netdev
  ...

10 files changed, 194 insertions, 11 deletions

diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
index d01ed63d3ebb..42409bfe04c4 100644
--- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
+++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
@@ -8,10 +8,16 @@ Required properties:
    - SerDes integration registers (1/2)
    - SerDes integration registers (2/2)
 
+Optional properties:
+- amd,speed-set: Speed capabilities of the device
+    0 - 1GbE and 10GbE (default)
+    1 - 2.5GbE and 10GbE
+
 Example:
 	xgbe_phy@e1240800 {
 		compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45";
 		reg = <0 0xe1240800 0 0x00400>,
 		      <0 0xe1250000 0 0x00060>,
 		      <0 0xe1250080 0 0x00004>;
+		amd,speed-set = <0>;
 	};
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe.txt b/Documentation/devicetree/bindings/net/amd-xgbe.txt
index ea0c7908a3b8..41354f730beb 100644
--- a/Documentation/devicetree/bindings/net/amd-xgbe.txt
+++ b/Documentation/devicetree/bindings/net/amd-xgbe.txt
@@ -8,16 +8,21 @@ Required properties:
 - interrupt-parent: Should be the phandle for the interrupt controller
   that services interrupts for this device
 - interrupts: Should contain the amd-xgbe interrupt
-- clocks: Should be the DMA clock for the amd-xgbe device (used for
-  calculating the correct Rx interrupt watchdog timer value on a DMA
-  channel for coalescing)
-- clock-names: Should be the name of the DMA clock, "dma_clk"
+- clocks:
+   - DMA clock for the amd-xgbe device (used for calculating the
+     correct Rx interrupt watchdog timer value on a DMA channel
+     for coalescing)
+   - PTP clock for the amd-xgbe device
+- clock-names: Should be the names of the clocks
+   - "dma_clk" for the DMA clock
+   - "ptp_clk" for the PTP clock
 - phy-handle: See ethernet.txt file in the same directory
 - phy-mode: See ethernet.txt file in the same directory
 
 Optional properties:
 - mac-address: mac address to be assigned to the device. Can be overridden
   by UEFI.
+- dma-coherent: Present if dma operations are coherent
 
 Example:
 	xgbe@e0700000 {
@@ -26,8 +31,8 @@ Example:
 		      <0 0xe0780000 0 0x80000>;
 		interrupt-parent = <&gic>;
 		interrupts = <0 325 4>;
-		clocks = <&xgbe_clk>;
-		clock-names = "dma_clk";
+		clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>;
+		clock-names = "dma_clk", "ptp_clk";
 		phy-handle = <&phy>;
 		phy-mode = "xgmii";
 		mac-address = [ 02 a1 a2 a3 a4 a5 ];
diff --git a/Documentation/devicetree/bindings/net/broadcom-systemport.txt b/Documentation/devicetree/bindings/net/broadcom-systemport.txt
index c183ea90d9bc..aa7ad622259d 100644
--- a/Documentation/devicetree/bindings/net/broadcom-systemport.txt
+++ b/Documentation/devicetree/bindings/net/broadcom-systemport.txt
@@ -4,7 +4,8 @@ Required properties:
 - compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport"
 - reg: address and length of the register set for the device.
 - interrupts: interrupts for the device, first cell must be for the the rx
-  interrupts, and the second cell should be for the transmit queues
+  interrupts, and the second cell should be for the transmit queues. An
+  optional third interrupt cell for Wake-on-LAN can be specified
 - local-mac-address: Ethernet MAC address (48 bits) of this adapter
 - phy-mode: Should be a string describing the PHY interface to the
   Ethernet switch/PHY, see Documentation/devicetree/bindings/net/ethernet.txt
diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
index 72efaaf764f7..0369e25aabd2 100644
--- a/Documentation/devicetree/bindings/net/davinci-mdio.txt
+++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
@@ -1,8 +1,8 @@
-TI SoC Davinci MDIO Controller Device Tree Bindings
+TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings
 ---------------------------------------------------
 
 Required properties:
-- compatible		: Should be "ti,davinci_mdio"
+- compatible		: Should be "ti,davinci_mdio" or "ti,keystone_mdio"
 - reg			: physical base address and size of the davinci mdio
 			  registers map
 - bus_freq		: Mdio Bus frequency
@@ -19,7 +19,7 @@ file.
 Examples:
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		reg = <0x4A101000 0x1000>;
 		bus_freq = <1000000>;
 	};
@@ -27,7 +27,7 @@ Examples:
 (or)
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		ti,hwmods = "davinci_mdio";
 		bus_freq = <1000000>;
 	};
diff --git a/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt
new file mode 100644
index 000000000000..0071883c08d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt
@@ -0,0 +1,29 @@
+*CC2520 IEEE 802.15.4 Compatible Radio*
+
+Required properties:
+	- compatible: 		should be "ti,cc2520"
+	- spi-max-frequency:	maximal bus speed (8000000), should be set to 4000000 depends
+				sync or async operation mode
+	- reg:			the chipselect index
+	- pinctrl-0: 		pin control group to be used for this controller.
+	- pinctrl-names: 	must contain a "default" entry.
+	- fifo-gpio:		GPIO spec for the FIFO pin
+	- fifop-gpio:		GPIO spec for the FIFOP pin
+	- sfd-gpio:		GPIO spec for the SFD pin
+	- cca-gpio:		GPIO spec for the CCA pin
+	- vreg-gpio:		GPIO spec for the VREG pin
+	- reset-gpio:		GPIO spec for the RESET pin
+Example:
+	cc2520@0 {
+		compatible = "ti,cc2520";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cc2520_cape_pins>;
+		fifo-gpio = <&gpio1 18 0>;
+		fifop-gpio = <&gpio1 19 0>;
+		sfd-gpio = <&gpio1 13 0>;
+		cca-gpio = <&gpio1 16 0>;
+		vreg-gpio = <&gpio0 31 0>;
+		reset-gpio = <&gpio1 12 0>;
+	};
diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt
new file mode 100644
index 000000000000..aa4f4230bfd7
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt
@@ -0,0 +1,61 @@
+* Marvell Armada 375 Ethernet Controller (PPv2)
+
+Required properties:
+
+- compatible: should be "marvell,armada-375-pp2"
+- reg: addresses and length of the register sets for the device.
+  Must contain the following register sets:
+	- common controller registers
+	- LMS registers
+  In addition, at least one port register set is required.
+- clocks: a pointer to the reference clocks for this device, consequently:
+	- main controller clock
+	- GOP clock
+- clock-names: names of used clocks, must be "pp_clk" and "gop_clk".
+
+The ethernet ports are represented by subnodes. At least one port is
+required.
+
+Required properties (port):
+
+- interrupts: interrupt for the port
+- port-id: should be '0' or '1' for ethernet ports, and '2' for the
+           loopback port
+- phy-mode: See ethernet.txt file in the same directory
+
+Optional properties (port):
+
+- marvell,loopback: port is loopback mode
+- phy: a phandle to a phy node defining the PHY address (as the reg
+  property, a single integer). Note: if this property isn't present,
+  then fixed link is assumed, and the 'fixed-link' property is
+  mandatory.
+
+Example:
+
+ethernet@f0000 {
+	compatible = "marvell,armada-375-pp2";
+	reg = <0xf0000 0xa000>,
+	      <0xc0000 0x3060>,
+	      <0xc4000 0x100>,
+	      <0xc5000 0x100>;
+	clocks = <&gateclk 3>, <&gateclk 19>;
+	clock-names = "pp_clk", "gop_clk";
+	status = "okay";
+
+	eth0: eth0@c4000 {
+		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+		port-id = <0>;
+		status = "okay";
+		phy = <&phy0>;
+		phy-mode = "gmii";
+	};
+
+	eth1: eth1@c5000 {
+		interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+		port-id = <1>;
+		status = "okay";
+		phy = <&phy3>;
+		phy-mode = "gmii";
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt
new file mode 100644
index 000000000000..3b58ae480344
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt
@@ -0,0 +1,33 @@
+* STMicroelectronics SAS. ST21NFCB NFC Controller
+
+Required properties:
+- compatible: Should be "st,st21nfcb_i2c".
+- clock-frequency: I²C work frequency.
+- reg: address on the bus
+- interrupt-parent: phandle for the interrupt gpio controller
+- interrupts: GPIO interrupt to which the chip is connected
+- reset-gpios: Output GPIO pin used to reset the ST21NFCB
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2):
+
+&i2c2 {
+
+	status = "okay";
+
+	st21nfcb: st21nfcb@8 {
+
+		compatible = "st,st21nfcb_i2c";
+
+		reg = <0x08>;
+		clock-frequency = <400000>;
+
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt
index e7106b50dbdc..34d4db1a4e25 100644
--- a/Documentation/devicetree/bindings/net/sh_eth.txt
+++ b/Documentation/devicetree/bindings/net/sh_eth.txt
@@ -9,6 +9,7 @@ Required properties:
 	      "renesas,ether-r8a7779"  if the device is a part of R8A7779 SoC.
 	      "renesas,ether-r8a7790"  if the device is a part of R8A7790 SoC.
 	      "renesas,ether-r8a7791"  if the device is a part of R8A7791 SoC.
+	      "renesas,ether-r8a7794"  if the device is a part of R8A7794 SoC.
 	      "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC.
 - reg: offset and length of (1) the E-DMAC/feLic register block (required),
        (2) the TSU register block (optional).
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
index a2acd2b26baf..9b03c57563a4 100644
--- a/Documentation/devicetree/bindings/net/stmmac.txt
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -25,6 +25,10 @@ Required properties:
 - snps,force_sf_dma_mode	Force DMA to use the Store and Forward
 				mode for both tx and rx. This flag is
 				ignored if force_thresh_dma_mode is set.
+- snps,multicast-filter-bins:	Number of multicast filter hash bins
+				supported by this device instance
+- snps,perfect-filter-entries:	Number of perfect filter entries supported
+				by this device instance
 
 Optional properties:
 - resets: Should contain a phandle to the STMMAC reset signal, if any
@@ -47,6 +51,8 @@ Examples:
 		mac-address = [000000000000]; /* Filled in by U-Boot */
 		max-frame-size = <3800>;
 		phy-mode = "gmii";
+		snps,multicast-filter-bins = <256>;
+		snps,perfect-filter-entries = <128>;
 		clocks = <&clock>;
 		clock-names = "stmmaceth">;
 	};
diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt
new file mode 100644
index 000000000000..5dbf169cd81c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt
@@ -0,0 +1,41 @@
+Broadcom BCM43xx Fullmac wireless SDIO devices
+
+This node provides properties for controlling the Broadcom wireless device. The
+node is expected to be specified as a child node to the SDIO controller that
+connects the device to the system.
+
+Required properties:
+
+ - compatible : Should be "brcm,bcm4329-fmac".
+
+Optional properties:
+ - brcm,drive-strength : drive strength used for SDIO pins on device in mA
+	(default = 6).
+ - interrupt-parent : the phandle for the interrupt controller to which the
+	device interrupts are connected.
+ - interrupts : specifies attributes for the out-of-band interrupt (host-wake).
+	When not specified the device will use in-band SDIO interrupts.
+ - interrupt-names : name of the out-of-band interrupt, which must be set
+	to "host-wake".
+
+Example:
+
+mmc3: mmc@01c12000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins_a>;
+	vmmc-supply = <&reg_vmmc3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <10 8>; /* PH10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};