Merge tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC updates from Arnd Bergmann:
 "The code changes are mostly for 32-bit platforms and include:

   - Lots of updates for the Nvidia Tegra platform, including cpuidle,
     pmc, and dt-binding changes

   - Microchip at91 power management updates for the recently added
     sam9x60 SoC

   - Treewide setup_irq deprecation by afzal mohammed

   - STMicroelectronics stm32 gains earlycon support

   - Renesas platforms with Cortex-A9 can now use the global timer

   - Some TI OMAP2+ platforms gain cpuidle support

   - Various cleanups for the i.MX6 and Orion platforms, as well as
     Kconfig files across all platforms"

* tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (75 commits)
  ARM: qcom: Add support for IPQ40xx
  ARM: mmp: replace setup_irq() by request_irq()
  ARM: cns3xxx: replace setup_irq() by request_irq()
  ARM: spear: replace setup_irq() by request_irq()
  ARM: ep93xx: Replace setup_irq() by request_irq()
  ARM: iop32x: replace setup_irq() by request_irq()
  arm: mach-dove: Mark dove_io_desc as __maybe_unused
  ARM: orion: replace setup_irq() by request_irq()
  ARM: debug: stm32: add UART early console support for STM32MP1
  ARM: debug: stm32: add UART early console support for STM32H7
  ARM: debug: stm32: add UART early console configuration for STM32F7
  ARM: debug: stm32: add UART early console configuration for STM32F4
  cpuidle: tegra: Disable CC6 state if LP2 unavailable
  cpuidle: tegra: Squash Tegra114 driver into the common driver
  cpuidle: tegra: Squash Tegra30 driver into the common driver
  cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
  ARM: tegra: cpuidle: Remove unnecessary memory barrier
  ARM: tegra: cpuidle: Make abort_flag atomic
  ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
  ARM: tegra: Make outer_disable() open-coded
  ...

1 files changed, 24 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
index 9fb682e47c29..38c5fa21f435 100644
--- a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
+++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
@@ -37,6 +37,7 @@ Required properties:
   - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
   - Tegra210: "nvidia,tegra210-xusb-padctl"
   - Tegra186: "nvidia,tegra186-xusb-padctl"
+  - Tegra194: "nvidia,tegra194-xusb-padctl"
 - reg: Physical base address and length of the controller's registers.
 - resets: Must contain an entry for each entry in reset-names.
 - reset-names: Must include the following entries:
@@ -62,6 +63,10 @@ For Tegra186:
 - vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
 - vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.
 
+For Tegra194:
+- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
+  3.3 V.
+- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
 
 Pad nodes:
 ==========
@@ -154,6 +159,11 @@ For Tegra210, the list of valid PHY nodes is given below:
 - sata: sata-0
   - functions: "usb3-ss", "sata"
 
+For Tegra194, the list of valid PHY nodes is given below:
+- usb2: usb2-0, usb2-1, usb2-2, usb2-3
+  - functions: "xusb"
+- usb3: usb3-0, usb3-1, usb3-2, usb3-3
+  - functions: "xusb"
 
 Port nodes:
 ===========
@@ -174,6 +184,12 @@ Required properties:
   - "device": for USB device mode
   - "otg": for USB OTG mode
 
+Required properties for OTG/Peripheral capable USB2 ports:
+- usb-role-switch: Boolean property to indicate that the port support OTG or
+  peripheral mode. If present, the port supports switching between USB host
+  and peripheral roles. Connector should be added as subnode.
+  See usb/usb-conn-gpio.txt.
+
 Optional properties:
 - nvidia,internal: A boolean property whose presence determines that a port
   is internal. In the absence of this property the port is considered to be
@@ -221,6 +237,11 @@ Optional properties:
   is internal. In the absence of this property the port is considered to be
   external.
 
+- maximum-speed: Only for Tegra194. A string property that specifies maximum
+  supported speed of a usb3 port. Valid values are:
+  - "super-speed-plus": default, the usb3 port supports USB 3.1 Gen 2 speed.
+  - "super-speed": the usb3 port supports USB 3.1 Gen 1 speed only.
+
 For Tegra124 and Tegra132, the XUSB pad controller exposes the following
 ports:
 - 3x USB2: usb2-0, usb2-1, usb2-2
@@ -233,6 +254,9 @@ For Tegra210, the XUSB pad controller exposes the following ports:
 - 2x HSIC: hsic-0, hsic-1
 - 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3
 
+For Tegra194, the XUSB pad controller exposes the following ports:
+- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
+- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3
 
 Examples:
 =========