dt-bindings: consolidate display related bindings

This is a quite large renaming to consolidate display related bindings
into a single "display" directory from various scattered locations of
video, drm, gpu, fb, mipi, and panel. The prior location was somewhat
based on the Linux driver location, but bindings should be independent
of that.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>

1 files changed, 120 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
new file mode 100644
index 000000000000..64693f2ebc51
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
@@ -0,0 +1,120 @@
+The Exynos display port interface should be configured based on
+the type of panel connected to it.
+
+We use two nodes:
+	-dp-controller node
+	-dptx-phy node(defined inside dp-controller node)
+
+For the DP-PHY initialization, we use the dptx-phy node.
+Required properties for dptx-phy: deprecated, use phys and phy-names
+	-reg: deprecated
+		Base address of DP PHY register.
+	-samsung,enable-mask: deprecated
+		The bit-mask used to enable/disable DP PHY.
+
+For the Panel initialization, we read data from dp-controller node.
+Required properties for dp-controller:
+	-compatible:
+		should be "samsung,exynos5-dp".
+	-reg:
+		physical base address of the controller and length
+		of memory mapped region.
+	-interrupts:
+		interrupt combiner values.
+	-clocks:
+		from common clock binding: handle to dp clock.
+	-clock-names:
+		from common clock binding: Shall be "dp".
+	-interrupt-parent:
+		phandle to Interrupt combiner node.
+	-phys:
+		from general PHY binding: the phandle for the PHY device.
+	-phy-names:
+		from general PHY binding: Should be "dp".
+	-samsung,color-space:
+		input video data format.
+			COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
+	-samsung,dynamic-range:
+		dynamic range for input video data.
+			VESA = 0, CEA = 1
+	-samsung,ycbcr-coeff:
+		YCbCr co-efficients for input video.
+			COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1
+	-samsung,color-depth:
+		number of bits per colour component.
+			COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
+	-samsung,link-rate:
+		link rate supported by the panel.
+			LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A
+	-samsung,lane-count:
+		number of lanes supported by the panel.
+			LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
+	- display-timings: timings for the connected panel as described by
+		Documentation/devicetree/bindings/display/display-timing.txt
+
+Optional properties for dp-controller:
+	-interlaced:
+		interlace scan mode.
+			Progressive if defined, Interlaced if not defined
+	-vsync-active-high:
+		VSYNC polarity configuration.
+			High if defined, Low if not defined
+	-hsync-active-high:
+		HSYNC polarity configuration.
+			High if defined, Low if not defined
+	-samsung,hpd-gpio:
+		Hotplug detect GPIO.
+			Indicates which GPIO should be used for hotplug
+			detection
+	-video interfaces: Device node can contain video interface port
+			    nodes according to [1].
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+SOC specific portion:
+	dp-controller {
+		compatible = "samsung,exynos5-dp";
+		reg = <0x145b0000 0x10000>;
+		interrupts = <10 3>;
+		interrupt-parent = <&combiner>;
+		clocks = <&clock 342>;
+		clock-names = "dp";
+
+		phys = <&dp_phy>;
+		phy-names = "dp";
+	};
+
+Board Specific portion:
+	dp-controller {
+		samsung,color-space = <0>;
+		samsung,dynamic-range = <0>;
+		samsung,ycbcr-coeff = <0>;
+		samsung,color-depth = <1>;
+		samsung,link-rate = <0x0a>;
+		samsung,lane-count = <4>;
+
+		display-timings {
+			native-mode = <&lcd_timing>;
+			lcd_timing: 1366x768 {
+				clock-frequency = <70589280>;
+				hactive = <1366>;
+				vactive = <768>;
+				hfront-porch = <40>;
+				hback-porch = <40>;
+				hsync-len = <32>;
+				vback-porch = <10>;
+				vfront-porch = <12>;
+				vsync-len = <6>;
+			};
+		};
+
+		ports {
+			port@0 {
+				dp_out: endpoint {
+					remote-endpoint = <&bridge_in>;
+				};
+			};
+		};
+	};